TSC FRAF1602G

FRAF1601G THRU FRAF1607G
Isolation 16.0 AMPS. Glass Passivated Fast Recovery Rectifiers
Voltage Range
50 to 1000 Volts
Current
16.0 Amperes
ITO-220AC
Features
.185(4.7)
.406(10.3)
.173(4.4)
Low forward voltage drop
High current capability
High reliability
High surge current capability
.390(9.90)
.124(3.16)
.118(3.00)
.13 4(3. 4)D IA
. 112 (2. 85)
. 11 3(3. 0)D IA
. 100 (2.5 5)
.2 72( 6. 9)
.2 48( 6. 3)
. 606(1 5.5 )
Mechanical Data
. 583(1 4.8 )
Cases: ITO-220AC molded plastic
Epoxy: UL 94V-0 rate flame retardant
Terminals: Leads solderable per
MIL-STD-202, Method 208 guaranteed
Polarity: As marked
High temperature soldering guaranteed:
260℃/10 seconds 0.25”,(6.35mm) from
case.
Mounting position: Any
Weight: 2.24 grams
Mounting torque: 5 in – 1bs. max.
.0 63 (1 .6 )
MA X
.161(4.1)
.146(3.7)
.110( 2.8)
. 071 (1. 8)
. 543( 13. 8)
MA X
. 512( 13. 2)
.0 98(2 .5)
2
PIN 1
. 10 0( 2 . 55)
. 100 (2.5 5)
PIN 2
Case Positive
Dimensions in inches and (millimeters)
Maximum Ratings and Electrical Characteristics
Rating at 25℃ambient temperature unless otherwise specified.
Single phase, half wave, 60 Hz, resistive or inductive load.
For capacitive load, derate current by 20%
Symbol FRAF FRAF FRAF FRAF FRAF FRAF FRAF Units
Type Number
1601G 1602G 1603G 1604G 1605G 1606G 1607G
Maximum Recurrent Peak Reverse Voltage
Maximum RMS Voltage
Maximum DC Blocking Voltage
Maximum Average Forward Rectified Current
See Fig. 1
Peak Forward Surge Current, 8.3 ms Single
Half Sine-wave Superimposed on Rated
Load (JEDEC method )
Maximum Instantaneous Forward Voltage
@ 16.0A
Maximum DC Reverse Current @ TC=25℃
at Rated DC Blocking Voltage @ TC=125℃
VRRM
VRMS
VDC
50
35
50
100
70
100
200
140
200
400
280
400
600
420
600
800 1000
560 700
800 1000
V
V
V
I(AV)
16.0
A
IFSM
250
A
VF
1.3
V
IR
5.0
100
uA
uA
nS
℃/W
℃
250
500
4.5
Operating and Storage Temperature Range TJ ,TSTG
-65 to +150
Notes: 1. Reverse Recovery Test Conditions: IF=0.5A, IR=1.0A, IRR=0.25A
2. Thermal Resistance from Junction to Case Per Leg Mounted on Heatsink size 2” x
3” x 0.25” Al-Plate
Maximum Reverse Recovery Time ( Note 1)
Typical Thermal Resistance (Note 2)
Trr
RθJC
- 466 -
150
RATINGS AND CHARACTERISTIC CURVES (FRAF1601G THRU FRAF1607G)
FIG.1- REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM
10W
NONINDUCTIVE
50W
NONINDUCTIVE
trr
+0.5A
(-)
DUT
(+)
50Vdc
(approx)
(-)
PULSE
GENERATOR
(NOTE 2)
1W
NON
INDUCTIVE
OSCILLOSCOPE
(NOTE 1)
(+)
-1.0A
1cm
FIG.2- MAXIMUM FORWARD CURRENT DERATING
CURVE
1000
12.0
8.0
4.0
0
0
50
100
150
o
PEAK FORWARD SURGE CURRENT. (A)
FIG.3- MAXIMUM NON-REPETITIVE FORWARD
SURGE CURRENT
300
250
INSTANTANEOUS REVERSE CURRENT. ( A)
16.0
CASE TEMPERATURE. ( C)
8.3ms Single Half Sine Wave
JEDEC Method
100
Tj=125 0C
10
Tj=25 0C
1.0
0.1
0
200
20
40
60
80
100
120
140
PERCENT OF RATED PEAK REVERSE VOLTAGE. (%)
150
FIG.6- TYPICAL INSTANTANEOUS
FORWARD CHARACTERISTICS
100
80
50
0
1
2
5
10
20
50
100
NUMBER OF CYCLES AT 60Hz
FIG.4- TYPICAL JUNCTION CAPACITANCE
300
250
CAPACITANCE.(pF)
SET TIME BASE FOR
5/ 10ns/ cm
FIG.5- TYPICAL REVERSE CHARACTERISTICS
200
150
INSTANTANEOUS FORWARD CURRENT. (A)
AVERAGE FORWARD CURRENT. (A)
NOTES: 1. Rise Time=7ns max. Input Impedance=
1 megohm 22pf
2. Rise Time=10ns max. Sourse Impedance=
50 ohms
20.0
0
-0.25A
40
20
10
4
2
1.0
.4
100
50
Tj=25 C
f=1.0MHz
Vsig=50mVp-p
.1
.8
0
0.1
0.5
1.0
Tj=25oC
Pulse Width=300 s
1% Duty Cycle
.2
0
5
10
50
100
500 1000
REVERSE VOLTAGE. (V)
- 467 -
.9
1.0
1.1
1.2
1.3
1.4
INSTANTANEOUS FORWARD VOLTAGE. (V)
1.5