UCC5343 PRELIMINARY IrDA Transceiver with Encoder/Decoder FEATURES • Micropower in the Sleep Mode, (2µA) • 3V to 5V Operation • Wide Dynamic Receiver Range from 200nA to 50mA Typical • Direct Interface to IrDA Compatible UARTs or Super I/O ICs • Supports IrDA Standard to 115.2kbps Data Rates • Transmitter Output Stage Capable to 500mA Sink Current • IrDA Compliant Modulation & Demodulation Scheme • Direct Interface to Standard UART • 16 Pin SSOP, SOIC and DIL Package DESCRIPTION The UCC5343 IrDA Transceiver with Encoder/Decoder supports the Physical Layer specifications of the IrDA standard. Additional functionality is provided by data format translation between standard UART and IrDA formats. The UCC5343 is readily interfaced to a standard UART. The Receiver has a limiting transresistance amplifier to detect a current signal from a PIN diode and drives RXX pulses into a UART. The receiver is capable of detecting input currents ranging from 200nA to greater than 50mA. The receiver signal path is frequency limited by an internal bandpass filter to reduce interference from other sources of IR energy. The output of the receiver is designed for direct interface to standard UARTs and Super I/O devices up to 115.2kbps. Internal resistors are provided for decoupling the pin diode supply, minimizing the number of required external components. The UCC5343 has low current consumption in the active mode, making it excellent for applications with low power requirements. The transmitter section has a low impedance open drain MOSFET output. It is capable of sinking 300mA from an output LED at 3V and 500mA at LED at 5V. BLOCK DIAGRAM UDG-97076 1/98 UCC5343 ABSOLUTE MAXIMUM RATINGS CONNECTION DIAGRAM AVDD, DVDD, CAT. . . . . . . . . . . . . . . . . . . . . . . . . –0.3V to 7V SLEEP, DET, TXX, LED, DVDD, CAT. . . . . . . . . . . . . . . . . . . –-0.3mA to AVDD + 0.3mA IRXX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –10mA to 10 mA IDET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 250mA ILED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1A Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TBA Storage Temperature . . . . . . . . . . . . . . . . . . . –65°C to +150°C Junction Temperature . . . . . . . . . . . . . . . . . . . –55°C to +150°C Lead Temperature (Soldering, 10sec.) . . . . . . . . . . . . . +300°C SSOP-16, SOIC-16 and DIL-16 (Top View) M Package, D and N Packages All voltages are positive with respect to AGND. DGND and PGND must be connected to AGND. Currents are positive into, negative out of the specified terminal. Consult Packaging Section of the Databook for thermal limitations and considerations of packages. ELECTRICAL CHARACTERISTICS: Unless otherwise specified, 0°C < TA < 70°C TA = 0°C to 70°C, AVDD = 3V to 5.5V, CAVDD = 100nF, CDVDD = 100nF, CCAT = 4.7µF + 100nF, CRXX = 40pF, CDET < 56pF. TA = TJ. PARAMETER TEST CONDITIONS MIN TYP MAX UNITS 280 450 µA 1 3 µA Supply Current Section IDD No Output Load, SLEEP ≤ 0.5V SLEEP > AVDD – 0.5V RVDD AVDD to DVDD 1.0 2 3.0 kΩ RCAT AVDD to CAT 15 20 32 Ω Receiver Section Input Referred Noise (Note 1) pA Hz 10 Detection Threshold 200 400 nA DetectionThreshold Signal to Noise Ratio IDET = 200nA (Note 1) Lower Band Limit (Note 1) 50 kHz Upper Band Limit (Note 1) 1 MHz Output Pulse Width IDET = 200nA Peak to 20mA Peak and 0 to 200µADC, 1.6µS Peak fUARTCLK = 2MHz 8.95 µS RXX Output (VOL) IRXX = 800µA 200 400 mV RXX Output (VOH) IRXX = –100µA, DVDD - RXX 200 400 mV RXX Rise Time 10% to 90% of DVDD 150 200 nS RXX Fall Time 90% to 10% of DVDD 100 150 nS –1 1 µA 11.8 Transmitter Section ITXX TXX = 0 to AVDD TXX (VIH) DVDD = 5V 0.7 • DVDD DVDD V TXX ( VIL) DVDD = 5V 0 0.3 • DVDD V LED TXX = 0, AVDD = 4.5V, ILED = 500mA 0.3 0.6 V TXX = 0, AVDD = 3V, ILED = 300mA 0.3 0.6 V 2.23 µS Encoder Transmit Section Encoder Output Pulse Width TXMODE = VDD 1.41 Note 1: Guaranteed by Design. Not 100% tested in production. 2 UCC5343 PIN DESCRIPTIONS AGND: Ground pin for analog circuits. AVDD: Supply pin for analog circuits. Bypass to AGND with 100nF or 1µF capacitor. CAT: This pin is a filtered supply for PIN diode cathode. Internally connected to AGND with a 20Ω resistor. Bypass to a GND with a 4.7µF electrolytic capacitor and a 100nF ceramic capacitor. DET: This is the input to the receiver amplifier. Connect pin diode anode to this pin. DGND: Ground pin for digital circuits. DVDD: Supply pin for digital circuits. Internally connected to AVDD through 2k resistor. This pin must be bypassed to DGND with a 100nf or 1µF ceramic capacitor. LED: LED pin is the output of the transmitter section of the chip. The signal on this pin is the IrDA encoded version of the UART transmit signal. PGND: Ground pin for the transmitter power device. This pin should be connected to the circuit board ground plane. RSTB: This active low input signal is used to reset the encoder and decoder sections of the chip. This signal must be provided by the system during startup. RXX: RXX is the demodulated receive signal. Normally this pin is tied to SIN signal of UART. TTL/CMOS compatible output from the receiver stage to an IrDA UART. This output is digitally decoded (pulse stretched). SLEEP: Sleep mode select pin. A logic high on SLEEP pin puts the chip into a low current mode. TXMODE: TXMODE is used to select the modulation mode. If TXMODE is set high (1) the signal on TXD pin will have the output pulse width of 1.6µS. If TXMODE is set low (0), the output will have the pulse width of 3/16 of the UARTCLK frequency. If TXMODE pin is left floating, the output will default to 1.6µS pulse width. TXX: Input from the UART. This pin is normally tied to SOUT signal of UART. UARTCLK: Input of the system clock. This frequency must set at 16 times the IrDA data rate, and must be available from the UART. APPLICATION INFORMATION Figures 1 and 2 outline the IrDA SIR encoding scheme. The encoding scheme relies on a clock being present. The clock must be set to 16 times the data transmission baud rate. The encoder sends a pulse for every space (0) that is sent. On a high to low transition of TXD signal, the generation of the pulse is delayed for 7 clock cycles of the 16XCLK before the pulse is set high for 3/16 of a bit time or 1.6µs the pulse width is selected by TXMODE. For consecutive spaces, pulses with 1 bit time delay are generated in series. If a logic 1 (mark) is sent, the encoder does not generate a pulse. UDG-97076 Figure 1. IrDA Encoder Timing Diagram 3 UCC5343 APPLICATION INFORMATION (cont.) UDG-97077 Figure 2. IrDA Encoder Timing Diagram (1.6µs Pulse Width) The IrDA SIR decoding modulation method performs a pulse stretching function. Every high to low transition of the IRRXD line signifies an arrival of a 3/16th pulse. This pulse needs to be stretched to accommodate 1 bit time (or 16 of 16XCLK cycles). Every pulse that is received is translated into a space (0) on the RXD output. If a series of pulses separated by 1 bit time are received, then the result is a 1 bit time low pulse for every 3/16 pulse received. The decoding scheme is shown in Figure 3. UDG-97078 Figure 3. IrDA Decoder Timing Diagram 4 UCC5343 APPLICATION INFORMATION (cont.) Ground Plane Analog Power Supply De-coupling There are 3 ground connections shown on the application drawing. They represent the sensitive analog ground, the dirty digital ground, and the high current transmitter ground. These 3 points can simply be geographic groupings of connections to a ground plane. If a ground plane is not used, other provision to isolate the analog and digital ground currents should be provided. The use of a ground plane is strongly recommended. The UCC5343 has a highly sensitive amplifier section capable of detecting extremely low current levels (200nA typical). Achieving this sensitivity requires quiet analog power supply rails. A 100nF high frequency capacitor in close proximity to AVDD and AGND is required for quiet analog rails. DET Considerations The DET circuit board trace should be surrounded with AGND in order to shield leakage noise from DET. The DET circuit board trace length should be minimized. Since the PIN diode connected to DET is capacitive, noise coupling to the cathode of the diode will be coupled directly to DET. For this reason, the 100nF capacitor on CAT should be located physically close to the cathode of the PIN diode. There is natural parasitic coupling from RXX to DET. RXX should be routed to minimize the parasitic capacitive coupling from RXX to DET. The transmitter section of the chip runs from the AVDD supply and draws high peak currents (~ 500 mA in a typical application). A bulk capacitor may be required physically close to the AVDD and AGND pins if the connection length to the power supply is long or if the supply is or appears to be relatively high impedance. This bulk capacitor is in addition to the 100nF high frequency capacitor mentioned above. The bypass capacitors on CAT and AVDD should present very low equivalent series resistance and inductance to the circuit. Digital Power Supply DVDD is fed directly from AVDD through an internal 2k resistor. The DVDD bypass cap handles all transient current produced by the digital section of the chip. If more drive is required from RXX than the internal 2k resistor will allow, an external resistor can shunt it. This technique should always be accompanied by increasing the value of the de-coupling capacitor on DVDD and AVDD. UDG-97160 Figure 4. IrDA Transceiver with UART Encoder/Decoder Logic UNITRODE CORPORATION 7 CONTINENTAL BLVD. • MERRIMACK, NH 03054 TEL. (603) 424-2410 • FAX (603) 424-3460 5 IMPORTANT NOTICE Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue any product or service without notice, and advise customers to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those pertaining to warranty, patent infringement, and limitation of liability. TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed, except those mandated by government requirements. CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE (“CRITICAL APPLICATIONS”). TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, AUTHORIZED, OR WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT DEVICES OR SYSTEMS OR OTHER CRITICAL APPLICATIONS. INCLUSION OF TI PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO BE FULLY AT THE CUSTOMER’S RISK. In order to minimize risks associated with the customer’s applications, adequate design and operating safeguards must be provided by the customer to minimize inherent or procedural hazards. TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right of TI covering or relating to any combination, machine, or process in which such semiconductor products or services might be or are used. TI’s publication of information regarding any third party’s products or services does not constitute TI’s approval, warranty or endorsement thereof. Copyright 1999, Texas Instruments Incorporated