WINBOND W77L32

Preliminary W77L32
8-BIT MICROCONTROLLER
Table of Contents-1. GENERAL DESCRIPTION..........................................................................................................................3
2. FEATURES .................................................................................................................................................3
3. PIN CONFIGURATIONS.............................................................................................................................4
4. PIN DESCRIPTION.....................................................................................................................................5
5. BLOCK DIAGRAM ......................................................................................................................................6
6. FUNCTIONAL DESCRIPTION....................................................................................................................7
I/O Ports.....................................................................................................................................................7
Serial I/O....................................................................................................................................................7
Timers........................................................................................................................................................8
Interrupts....................................................................................................................................................8
Data Pointers .............................................................................................................................................8
Power Management...................................................................................................................................8
On-chip Data SRAM ..................................................................................................................................8
7. MEMORY ORGANIZATION ........................................................................................................................8
Program Memory .......................................................................................................................................8
Data Memory .............................................................................................................................................9
Special Function Registers ......................................................................................................................10
Special Function Registers ......................................................................................................................11
8. INSTRUCTION..........................................................................................................................................28
Intruction Timing ......................................................................................................................................35
9. POWER MANAGEMENT..........................................................................................................................43
Idle Mode .................................................................................................................................................43
Economy Mode ........................................................................................................................................43
Power Down Mode ..................................................................................................................................44
10. RESET CONDITIONS.............................................................................................................................45
External Reset ........................................................................................................................................45
Watchdog Timer Reset...........................................................................................................................45
Reset State .............................................................................................................................................46
11. INTERRUPTS .........................................................................................................................................47
Interrupt Sources ....................................................................................................................................47
Priority Level Structure ...........................................................................................................................48
Interrupt Response Time ........................................................................................................................49
-1-
Publication Release Date: November 2, 2001
Revision A1
Preliminary W77L32
12. PROGRAMMABLE TIMERS/COUNTERS ..............................................................................................50
Timer/Counters 0 & 1..............................................................................................................................50
Time-base Selection ...............................................................................................................................50
Timer/Counter 2......................................................................................................................................53
Baud Rate Generator Mode....................................................................................................................55
Watchdog Timer .....................................................................................................................................56
Serial Port ...............................................................................................................................................58
Timed Access Protection ........................................................................................................................64
13. ABSOLUTE MAXIMUM RATINGS..........................................................................................................65
14. DC ELECTRICAL CHARACTERISTICS .................................................................................................66
External Clock Characteristics................................................................................................................67
AC Specification .....................................................................................................................................67
15. TIMING WAVEFORMS ...........................................................................................................................69
Program Memory Read Cycle.................................................................................................................69
Data Memory Read Cycle.......................................................................................................................70
Data Memory Write Cycle.......................................................................................................................70
16. TYPICAL APPLICATION CIRCUITS.......................................................................................................71
Expanded External Program Memory and Crystal..................................................................................71
Expanded External Data Memory and Oscillator....................................................................................72
17. PACKAGE DIMENSIONS .......................................................................................................................72
40-pin DIP...............................................................................................................................................72
44-pin PLCC ...........................................................................................................................................73
44-pin QFP .............................................................................................................................................73
-2-
Preliminary W77L32
1. GENERAL DESCRIPTION
The W77L32 is a fast 8051 compatible microcontroller with a redesigned processor core without
wasted clock and memory cycles. As a result, it executes every 8051 instruction faster than the original
8051 for the same crystal speed. Typically, the instruction executing time of W77L32 is 1.5 to 3 times
faster then that of traditional 8051, depending on the type of instruction. In general, the overall
performance is about 2.5 times better than the original for the same crystal speed. Giving the same
throughput with lower clock speed, power consumption has been improved. Consequently, the
W77L32 is a fully static CMOS design; it can also be operated at a lower crystal clock. W77L32
support on-chip 1KB SRAM without external memory component and glue logic, saving more I/O pins
for users application usage if they use on-chip SRAM instead of external SRAM.
2. FEATURES
• 8-bit CMOS microcontroller
• High speed architecture of 4 clocks/machine cycle
• Pin compatible with standard 80C52
• Instruction-set compatible with MCS-51
• Four 8-bit I/O Ports
• One extra 4-bit I/O port and Wait State control signal (available on 44-pin PLCC/QFP package)
• Three 16-bit Timers
• 12 interrupt sources with two levels of priority
• On-chip oscillator and clock circuitry
• Two enhanced full duplex serial ports
• 256 bytes scratch-pad RAM
• 1KB on-chip SRAM for MOVX instruction
• Programmable Watchdog Timer
• Dual 16-bit Data Pointers
• Software programmable access cycle to external RAM/peripherals
• Packages:
− DIP 40: W77L32-25
− PLCC 44: W77L32P-25
− QFP 44: W77L32F-25
-3-
Publication Release Date: November 2, 2001
Revision A1
Preliminary W77L32
3. PIN CONFIGURATIONS
40-Pin DIP (W77L32)
T2, P1.0
T2EX, P1.1
RXD1, P1.2
TXD1, P1.3
INT2, P1.4
INT3, P1.5
INT4, P1.6
INT5, P1.7
RST
RXD, P3.0
TXD, P3.1
INT0, P3.2
INT1, P3.3
T0, P3.4
T1, P3.5
WR, P3.6
RD, P3.7
XTAL2
XTAL1
VSS
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
INT3, P1.5
INT4, P1.6
INT5, P1.7
RST
RXD, P3.0
P4.3
TXD, P3.1
INT0, P3.2
INT1, P3.3
T0, P3.4
T1, P3.5
T
X
D
1
,
P
1
.
3
R
X
D
1
,
P
1
.
2
T
2
E
X
,
P
1
.
1
T
2
,
P
1
.
0
A
D
0
,
P
P
4 V 0
. D .
2 D 0
A
D
1
,
P
0
.
1
A
D
2
,
P
0
.
2
P
3
.
7
,
/
R
D
X
T
A
L
2
X V P P
T S 4 2
A S . .
0 0
L
, ,
1
/ A
W 8
A
I
T
EA
ALE
PSEN
P2.7, A15
P2.6, A14
P2.5, A13
P2.4, A12
P2.3, A11
P2.2, A10
P2.1, A9
P2.0, A8
P
2
.
1
,
A
9
P
2
.
2
,
A
1
0
P
2
.
3
,
A
1
1
I
N
T
2
,
P
1
.
4
A
D
3
,
P
0
.
3
6 5 4 3 2 1 44 43 42 41 40
7
39
8
38
9
37
10
36
11
35
12
34
13
33
14
32
15
31
16
30
17
29
18 19 20 21 22 23 24 25 26 27 28
P
3
.
6
,
/
W
R
P0.0, AD0
P0.1, AD1
P0.2, AD2
P0.3, AD3
P0.4, AD4
P0.5, AD5
P0.6, AD6
P0.7, AD7
44-Pin QFP (W77L32F)
44-Pin PLCC (W77L32P)
I
N
T
2
,
P
1
.
4
VDD
P0.4, AD4
P0.5, AD5
P0.6, AD6
P0.7, AD7
INT3, P1.5
INT4, P1.6
INT5, P1.7
RST
RXD, P3.0
P4.3
TXD, P3.1
EA
P4.1
ALE
PSEN
P2.7, A15
P2.6, A14
P2.5, A13
INT0, P3.2
INT1, P3.3
T0, P3.4
T1, P3.5
P
2
.
4
,
A
1
2
R
X
D
1
,
P
1
.
2
T
2
E
X
,
P
1
.
1
T
2
,
P
1
.
0
A
D
0
,
P
P
4 V 0
. D .
2 D 0
A
D
1
,
P
0
.
1
A
D
2
,
P
0
.
2
A
D
3
,
P
0
.
3
44 43 42 41 40 39 38 37 36 35 34
33
32
31
3
30
4
29
5
28
6
27
7
26
8
9
25
10
24
23
11
12 13 14 15 16 17 18 19 20 21 22
1
2
P
3
.
6
,
/
W
R
-4-
T
X
D
1
,
P
1
.
3
P
3
.
7
,
/
R
D
X
T
A
L
2
X V P P
T S 4 2
A S . .
0 0
L
, ,
1
/ A
W 8
A
I
T
P
2
.
1
,
A
9
P
2
.
2
,
A
1
0
P
2
.
3
,
A
1
1
P
2
.
4
,
A
1
2
P0.4, AD4
P0.5, AD5
P0.6, AD6
P0.7, AD7
EA
P4.1
ALE
PSEN
P2.7, A15
P2.6, A14
P2.5, A13
Preliminary W77L32
4. PIN DESCRIPTION
SYMBOL
TYPE
DESCRIPTIONS
EA
I
EXTERNAL ACCESS ENABLE: It should be kept low.
PSEN
O
PROGRAM STORE ENABLE: PSEN enables the external ROM data onto the Port 0
address/data bus during fetch and MOVC operations.
ALE
O
ADDRESS LATCH ENABLE: ALE is used to enable the address latch that separates
the address from the data on Port 0.
RST
I
RESET: A high on this pin for two machine cycles while the oscillator is running resets
the device.
XTAL1
I
CRYSTAL1: This is the crystal oscillator input. This pin may be driven by an external
clock.
XTAL2
O
CRYSTAL2: This is the crystal oscillator output. It is the inversion of XTAL1.
VSS
I
GROUND: Ground potential
POWER SUPPLY: Supply voltage for operation.
VDD
I
P0.0 − P0.7
I/O
PORT 0: Port 0 is an open-drain bi-directional I/O port. This port also provides a
multiplexed low order address/data bus during accesses to external memory.
P1.0 − P1.7
I/O
PORT 1: Port 1 is a bi-directional I/O port with internal pull-ups. The bits have alternate
functions which are described below:
T2(P1.0): Timer/Counter 2 external count input
T2EX(P1.1): Timer/Counter 2 Reload/Capture/Direction control
RXD1(P1.2): Serial port 1 RXD
TXD1(P1.3): Serial port 1 TXD
INT2(P1.4) : External Interrupt 2
INT3 (P1.5): External Interrupt 3
INT4(P1.6) : External Interrupt 4
INT5 (P1.7): External Interrupt 5
P2.0 − P2.7
I/O
PORT 2: Port 2 is a bi-directional I/O port with internal pull-ups. This port also provides
the upper address bits for accesses to external memory.
P3.0 − P3.7
I/O
PORT 3: Port 3 is a bi-directional I/O port with internal pull-ups. All bits have alternate
functions, which are described below:
RXD(P3.0) : Serial Port 0 input
TXD(P3.1) : Serial Port 0 output
INT0 (P3.2): External Interrupt 0
INT1 (P3.3): External Interrupt 1
T0(P3.4) : Timer 0 External Input
T1(P3.5) : Timer 1 External Input
WR (P3.6) : External Data Memory Write Strobe
RD (P3.7) : External Data Memory Read Strobe
P4.0 − P4.3
I/O
PORT 4: Port 4 is a 4-bit bi-directional I/O port. The P4.0 also provides the alternate
function WAIT which is the wait state control signal.
* Note: TYPE I: input, O: output, I/O: bi-directional.
-5-
Publication Release Date: November 2, 2001
Revision A1
Preliminary W77L32
5. BLOCK DIAGRAM
P1.0
I
Port
1
Port 1
Latch
ACC
P1.7
B
Port 0
Latch
Port
0
P0.0
I
P0.7
T1 Register
T2 Register
Interrupt
DPTR
PSW
Stack
Pointer
ALU
Timer
2
DPTR 1
Temp Reg.
Address
Bus
PC
Timer
0
Incrementor
SFR RAM Address
Timer
1
Addr. Reg.
Instruction
Decoder
&
Sequencer
256 bytes
RAM & SFR
2 UARTs
P3.0
ò
I
P3.7
P4.0
I
P4.3
Port
3
Port 3
Latch
1KB SRAM
Bus & lock
Controller
Port 2
Latch
Port
2
P2.0
I
P2.7
Port
4
Port 4
Latch
Oscillator
Power control
&
Power monitor
Reset Block
Watchdog Timer
XTAL1 XTAL2
ALE PSEN
RST
-6-
VCC
GND
Preliminary W77L32
6. FUNCTIONAL DESCRIPTION
The W77L32 is 8052 pin compatible and instruction set compatible. It includes the resources of the
standard 8052 such as four 8-bit I/O Ports, three 16-bit timer/counters, full duplex serial port and
interrupt sources.
The W77L32 features a faster running and better performance 8-bit CPU with a redesigned core
processor without wasted clock and memory cycles. it improves the performance not just by running at
high frequency but also by reducing the machine cycle duration from the standard 8052 period of
twelve clocks to four clock cycles for the majority of instructions. This improves performance by an
average of 1.5 to 3 times. The W77L32 also provides dual Data Pointers (DPTRs) to speed up block
data memory transfers. It can also adjust the duration of the MOVX instruction (access to off-chip data
memory) between two machine cycles and nine machine cycles. This flexibility allows the W77L32 to
work efficiently with both fast and slow RAMs and peripheral devices. In addition, the W77L32 contains
on-chip 1KB MOVX SRAM, the address of which is between 0000H and 03FFH. It only can be
accessed by MOVX instruction; this on-chip SRAM is optional under software control.
The W77L32 is an 8052 compatible device that gives the user the features of the original 8052 device,
but with improved speed and power consumption characteristics. It has the same instruction set as the
8051 family, with one addition: DEC DPTR (op-code A5H, the DPTR is decreased by 1). While the
original 8051 family was designed to operate at 12 clock periods per machine cycle, the W77L32
operates at a much reduced clock rate of only 4 clock periods per machine cycle. This naturally speeds
up the execution of instructions. Consequently, the W77L32 can run at a higher speed as compared to
the original 8052, even if the same crystal is used. Since the W77L32 is a fully static CMOS design, it
can also be operated at a lower crystal clock, giving the same throughput in terms of instruction
execution, yet reducing the power consumption.
The 4 clocks per machine cycle feature in the W77L32 is responsible for a three-fold increase in
execution speed. The W77L32 has all the standard features of the 8052, and has a few extra
peripherals and features as well.
I/O Ports
The W77L32 has four 8-bit ports and one extra 4-bit port. Port 0 can be used as an Address/Data bus
when external program is running or external memory/device is accessed by MOVC or MOVX
instruction. In these cases, it has strong pull-ups and pull-downs, and does not need any external pullups. Otherwise it can be used as a general I/O port with open-drain circuit. Port 2 is used chiefly as the
upper 8-bits of the Address bus when port 0 is used as an address/data bus. It also has strong pull-ups
and pull-downs when it serves as an address bus. Port 1 and 3 act as I/O ports with alternate
functions. Port 4 is only available on 44-pin PLCC/QFP package type. It serves as a general purpose
I/O port as Port 1 and Port 3. The P4.0 has an alternate function WAIT which is the wait state control
signal. When wait state control signal is enabled, P4.0 is input only.
Serial I/O
The W77L32 has two enhanced serial ports that are functionally similar to the serial port of the original
8052 family. However the serial ports on the W77L32 can operate in different modes in order to obtain
timing similarity as well. Note that the serial port 0 can use Timer 1 or 2 as baud rate generator,
but the serial port 1 can only use Timer 1 as baud rate generator. The serial ports have the
enhanced features of Automatic Address recognition and Frame Error detection.
-7-
Publication Release Date: November 2, 2001
Revision A1
Preliminary W77L32
Timers
The W77L32 has three 16-bit timers that are functionally similar to the timers of the 8052 family. When
used as timers, they can be set to run at either 4 clocks or 12 clocks per count, thus providing the user
with the option of operating in a mode that emulates the timing of the original 8052. The W77L32 has
an additional feature, the watchdog timer. This timer is used as a System Monitor or as a very long
time period timer.
Interrupts
The Interrupt structure in the W77L32 is slightly different from that of the standard 8052. Due to the
presence of additional features and peripherals, the number of interrupt sources and vectors has been
increased. The W77L32 provides 12 interrupt resources with two priority level, including six external
interrupt sources, timer interrupts, serial I/O interrupts and power-fail interrupt.
Data Pointers
The original 8052 had only one 16-bit Data Pointer (DPL, DPH). In the W77L32, there is an additional
16-bit Data Pointer (DPL1, DPH1). This new Data Pointer uses two SFR locations which were unused
in the original 8052. In addition there is an added instruction, DEC DPTR (op-code A5H), which helps
in improving programming flexibility for the user.
Power Management
Like the standard 80C52, the W77L32 also has IDLE and POWER DOWN modes of operation. The
W77L32 provides a new Economy mode which allow user to switch the internal clock rate divided by
either 4, 64 or 1024. In the IDLE mode, the clock to the CPU core is stopped while the timers, serial
ports and interrupts clock continue to operate. In the POWER DOWN mode, all the clock are stopped
and the chip operation is completely stopped. This is the lowest power consumption state.
On-chip Data SRAM
The W77L32 has 1K Bytes of data space SRAM which is read/write accessible and is memory
mapped. This on-chip MOVX SRAM is reached by the MOVX instruction. It is not used for executable
program memory. There is no conflict or overlap among the 256 bytes Scratchpad RAM and the 1K
Bytes MOVX SRAM as they use different addressing modes and separate instructions. The on-chip
MOVX SRAM is enabled by setting the DME0 bit in the PMR register. After a reset, the DME0 bit is
cleared such that the on-chip MOVX SRAM is disabled, and all data memory spaces 0000H − FFFFH
access to the external memory.
7. MEMORY ORGANIZATION
The W77L32 separates the memory into two separate sections, the Program Memory and the Data
Memory. The Program Memory is used to store the instruction op-codes, while the Data Memory is
used to store data or for memory mapped devices.
Program Memory
The Program Memory on the W77L32 can be up to 64Kbytes long. All instructions are fetched for
execution from this memory area. The MOVC instruction can also access this memory region.
-8-
Preliminary W77L32
Data Memory
The W77L32 can access up to 64Kbytes of external Data Memory. This memory region is accessed by
the MOVX instructions. Unlike the 8051 derivatives, the W77L32 contains on-chip 1K bytes MOVX
SRAM of Data Memory, which can only be accessed by MOVX instructions. These 1K bytes of SRAM
are between address 0000H and 03FFH. Access to the on-chip MOVX SRAM is optional under
software control. When enabled by software, any MOVX instruction that uses this area will go to the
on-chip RAM. MOVX addresses greater than 03FFH automatically go to external memory through Port
0 and 2. When disabled, the 1KB memory area is transparent to the system memory map. Any MOVX
directed to the space between 0000H and FFFFH goes to the expanded bus on Port 0 and 2. This is
the default condition. In addition, the W77L32 has the standard 256 bytes of on-chip Scratchpad RAM.
This can be accessed either by direct addressing or by indirect addressing. There are also some
Special Function Registers (SFRs), which can only be accessed by direct addressing. Since the
Scratchpad RAM is only 256 bytes, it can be used only when data contents are small. In the event that
larger data contents are present, two selections can be used. One is on-chip MOVX SRAM , the other
is the external Data Memory. The on-chip MOVX SRAM can only be accessed by a MOVX instruction,
the same as that for external Data Memory. However, the on-chip RAM has the fastest access times.
FFh
80h
7Fh
00h
Indirect
Addressing
RAM
FFFFh
FFFFh
SFRs
Direct
Addressing
only
64 K
Bytes
External
Data
Memory
Direct &
Indirect
Addressing
RAM
03FFh
0000h
64K bytes
of
External
Program
Memory
1K Bytes
On-chip SRAM
0000h
0000h
Figure 1. Memory Map
-9-
Publication Release Date: November 2, 2001
Revision A1
Preliminary W77L32
FFh
Indirect RAM
80h
7Fh
30h
2Fh
2Eh
2Dh
2Ch
2Bh
2Ah
29h
28h
27h
26h
25h
24h
23h
22h
21h
20h
1Fh
18h
17h
10h
0Fh
08h
07h
00h
Direct RAM
7F
77
6F
67
5F
57
4F
47
3F
37
2F
27
1F
17
0F
07
7E
76
6E
66
5E
56
4E
46
3E
36
2E
26
1E
16
0E
06
7D
75
6D
65
5D
55
4D
45
3D
35
2D
25
1D
15
0D
05
7C
74
6C
64
5C
54
4C
44
3C
34
2C
24
1C
14
0C
04
7B
73
6B
63
5B
53
4B
43
3B
33
2B
23
1B
13
0B
03
7A
72
6A
62
5A
52
4A
42
3A
32
2A
22
1A
12
0A
02
79
71
69
61
59
51
49
41
39
31
29
21
19
11
09
01
Bank 3
Bank 2
Bank 1
Bank 0
Figure 2. Scratchpad RAM / Register Addressing
- 10 -
78
70
68
60
58
50
48
40
38
30
28
20
18
10
08
00
Bit Addressable
20H−2FH
Preliminary W77L32
Special Function Registers
The W77L32 uses Special Function Registers (SFRs) to control and monitor peripherals and their
Modes.
The SFRs reside in the register locations 80-FFh and are accessed by direct addressing only. Some of
the SFRs are bit addressable. This is very useful in cases where one wishes to modify a particular bit
without changing the others. The SFRs that are bit addressable are those whose addresses end in 0 or
8. The W77L32 contains all the SFRs present in the standard 8052. However, some additional SFRs
have been added. In some cases unused bits in the original 8052 have been given new functions. The
list of SFRs is as follows. The table is condensed with eight locations per row. Empty locations indicate
that there are no registers at these addresses. When a bit or register is not implemented, it will read
high.
Table 1. Special Function Register Location Table
F8
EIP
F0
B
E8 EIE
E0 ACC
D8 WDCON
D0 PSW
C8 T2CON
T2MOD
RCAP2L
RCAP2H
C0 SCON1
SBUF1
ROMMAP
B8 IP
SADEN
SADEN1
SADDR
SADDR1
TL2
TH2
PMR
STATUS
TA
B0 P3
A8 IE
A0 P2
P4
98
SCON0
SBUF
90
P1
EXIF
88
TCON
80
P0
TMOD
TL0
TL1
TH0
TH1
CKCON
SP
DPL
DPH
DPL1
DPH1
DPS
PCON
Note: The SFRs in the column with dark borders are bit-addressable.
A brief description of the SFRs now follows.
Port 0
Bit:
7
6
5
4
3
2
1
0
P0.7
P0.6
P0.5
P0.4
P0.3
P0.2
P0.1
P0.0
Mnemonic: P0
Address: 80h
- 11 -
Publication Release Date: November 2, 2001
Revision A1
Preliminary W77L32
Port 0 is an open-drain bi-directional I/O port. This port also provides a multiplexed low order
address/data bus during accesses to external memory.
Stack Pointer
Bit:
7
6
5
4
3
2
1
0
SP.7
SP.6
SP.5
SP.4
SP.3
SP.2
SP.1
SP.0
Mnemonic: SP
Address: 81h
The Stack Pointer stores the Scratchpad RAM address where the stack begins. In other words, it
always points to the top of the stack.
Data Pointer Low
Bit:
7
6
5
4
3
2
1
0
DPL.7
DPL.6
DPL.5
DPL.4
DPL.3
DPL.2
DPL.1
DPL.0
Mnemonic: DPL
Address: 82h
This is the low byte of the standard 8052 16-bit data pointer.
Data Pointer High
Bit:
7
6
5
4
3
2
1
0
DPH.7
DPH.6
DPH.5
DPH.4
DPH.3
DPH.2
DPH.1
DPH.0
Mnemonic: DPH
Address: 83h
This is the high byte of the standard 8052 16-bit data pointer.
Data Pointer Low1
7
6
5
4
3
2
1
0
DPL1.7
DPL1.6
DPL1.5
DPL1.4
DPL1.3
DPL1.2
DPL1.1
DPL1.0
Bit:
Mnemonic: DPL1
Address: 84h
This is the low byte of the new additional 16-bit data pointer that has been added to the W77L32. The
user can switch between DPL, DPH and DPL1, DPH1 simply by setting register DPS = 1. The
instructions that use DPTR will now access DPL1 and DPH1 in place of DPL and DPH. If they are not
required they can be used as conventional register locations by the user.
Data Pointer High1
Bit:
7
6
5
4
3
2
1
0
DPH1.7
DPH1.6
DPH1.5
DPH1.4
DPH1.3
DPH1.2
DPH1.1
DPH1.0
Mnemonic: DPH1
Address: 85h
This is the high byte of the new additional 16-bit data pointer that has been added to the W77L32. The
user can switch between DPL, DPH and DPL1, DPH1 simply by setting register DPS = 1. The
- 12 -
Preliminary W77L32
instructions that use DPTR will now access DPL1 and DPH1 in place of DPL and DPH. If they are not
required they can be used as conventional register locations by the user.
Data Pointer Select
Bit:
7
6
5
4
3
2
1
0
-
-
-
-
-
-
-
DPS.0
Mnemonic: DPS
Address: 86h
DPS.0: This bit is used to select either the DPL,DPH pair or the DPL1, DPH1 pair as the active Data
Pointer. When set to 1, DPL1, DPH1 will be selected, otherwise DPL, DPH will be selected.
DPS.1 − 7: These bits are reserved, but will read 0.
Power Control
Bit:
7
6
5
4
3
2
1
0
SM0D
SMOD0
-
-
GF1
GF0
PD
IDL
Mnemonic: PCON
Address: 87h
SMOD : This bit doubles the serial port baud rate in mode 1, 2, and 3 when set to 1.
SMOD0: Framing Error Detection Enable: When SMOD0 is set to 1, then SCON.7(SCON1.7) indicates
a Frame Error and acts as the FE(FE_1) flag. When SMOD0 is 0, then SCON.7(SCON1.7)
acts as per the standard 8052 function.
GF1 − 0: These two bits are general purpose user flags.
PD:
Setting this bit causes the W77L32 to go into the POWER DOWN mode. In this mode all the
clocks are stopped and program execution is frozen.
IDL:
Setting this bit causes the W77L32 to go into the IDLE mode. In this mode the clocks to the
CPU are stopped, so program execution is frozen. But the clock to the serial, timer and
interrupt blocks is not stopped, and these blocks continue operating.
Timer Control
Bit:
7
6
5
4
3
2
1
0
TF1
TR1
TF0
TR0
IE1
IT
IE0
IT
Mnemonic: TCON
Address: 88h
TF1:
Timer 1 overflow flag: This bit is set when Timer 1 overflows. It is cleared automatically when
the program does a timer 1 interrupt service routine. Software can also set or clear this bit.
TR1:
Timer 1 run control: This bit is set or cleared by software to turn timer/counter on or off.
TF0:
Timer 0 overflow flag: This bit is set when Timer 0 overflows. It is cleared automatically when
the program does a timer 0 interrupt service routine. Software can also set or clear this bit.
TR0:
Timer 0 run control: This bit is set or cleared by software to turn timer/counter on or off.
- 13 -
Publication Release Date: November 2, 2001
Revision A1
Preliminary W77L32
IE1:
Interrupt 1 edge detect: Set by hardware when an edge/level is detected on INT1. This bit is
cleared by hardware when the service routine is vectored to only if the interrupt was edge
triggered. Otherwise it follows the pin.
IT1:
Interrupt 1 type control: Set/cleared by software to specify falling edge/ low level triggered
external inputs.
IE0:
Interrupt 0 edge detect: Set by hardware when an edge/level is detected on INT0 . This bit is
cleared by hardware when the service routine is vectored to only if the interrupt was edge
triggered. Otherwise it follows the pin.
IT0:
Interrupt 0 type control: Set/cleared by software to specify falling edge/ low level triggered
external inputs.
Timer Mode Control
Bit:
7
6
5
4
3
2
1
0
GATE
C/ T
M1
M0
GATE
C/ T
M1
M0
TIMER1
TIMER0
Mnemonic: TMOD
Address: 89h
GATE: Gating control: When this bit is set, Timer/counter x is enabled only while INTx pin is high and
TRx control bit is set. When cleared, Timer x is enabled whenever TRx control bit is set.
C/ T :
Timer or Counter Select: When cleared, the timer is incremented by internal clocks. When set,
the timer counts high-to-low edges of the Tx pin.
M1, M0: Mode Select bits:
M1
M0
Mode
0
0
Mode 0: 8-bits with 5-bit prescale.
0
1
Mode 1: 18-bits, no prescale.
1
0
Mode 2: 8-bits with auto-reload from THx
1
1
Mode 3: (Timer 0) TL0 is an 8-bit timer/counter controlled by the
standard Timer 0 control bits. TH0 is a 8-bit timer only controlled by
Timer 1 control bits. (Timer 1) Timer/counter is stopped.
Timer 0 LSB
Bit:
7
6
5
4
3
2
1
0
TL0.7
TL0.6
TL0.5
TL0.4
TL0.3
TL0.2
TL0.1
TL0.0
Mnemonic: TL0
Address: 8Ah
TL0.7 − 0: Timer 0 LSB
- 14 -
Preliminary W77L32
Timer 1 LSB
Bit:
7
6
5
4
3
2
1
0
TL1.7
TL1.6
TL1.5
TL1.4
TL1.3
TL1.2
TL1.1
TL1.0
Mnemonic: TL1
Address: 8Bh
TL1.7 − 0: Timer 1 LSB
Timer 0 MSB
Bit:
7
6
5
4
3
2
1
0
TH0.7
TH0.6
TH0.5
TH0.4
TH0.3
TH0.2
TH0.1
TH0.0
Mnemonic: TH0
Address: 8Ch
TH0.7 − 0: Timer 0 MSB
Timer 1 MSB
Bit:
7
6
5
4
3
2
1
0
TH1.7
TH1.6
TH1.5
TH1.4
TH1.3
TH1.2
TH1.1
TH1.0
Mnemonic: TH1
Address: 8Dh
TH1.7 − 0: Timer 1 MSB
Clock Control
Bit:
7
6
5
4
3
2
1
0
WD1
WD0
T2M
T1M
T0M
MD2
MD1
MD0
Mnemonic: CKCON
Address: 8Eh
WD1 − 0: Watchdog timer mode select bits: These bits determine the time-out period for the watchdog
timer. In all four time-out options the reset time-out is 512 clocks more than the interrupt
time-out period.
WD1 WD0 Interrupt time-out
Reset time-out
0
0
1
1
0
1
0
1
17
17
2
2
20
20
2
2
23
23
2
2
26
26
2
2
+ 512
+ 512
+ 512
+ 512
T2M:
Timer 2 clock select: When T2M is set to 1, timer 2 uses a divide by 4 clock, and when set to 0
it uses a divide by 12 clock
T1M:
Timer 1 clock select: When T1M is set to 1, timer 1 uses a divide by 4 clock, and when set to 0
it uses a divide by 12 clock.
T0M:
Timer 0 clock select: When T0M is set to 1, timer 0 uses a divide by 4 clock, and when set to 0
it uses a divide by 12 clock.
- 15 -
Publication Release Date: November 2, 2001
Revision A1
Preliminary W77L32
MD2 − 0: Stretch MOVX select bits: These three bits are used to select the stretch value for the MOVX
instruction. Using a variable MOVX length enables the user to access slower external
memory devices or peripherals without the need for external circuits. The RD or WR strobe
will be stretched by the selected interval. When accessing the on-chip SRAM, the MOVX
instruction is always in 2 machine cycles regardless of the stretch setting. By default, the
stretch has value of 1. If the user needs faster accessing, then a stretch value of 0 should be
selected.
MD2 MD1 MD0 Stretch value MOVX duration
0
0
0
0
2 machine cycles
0
0
1
1
3 machine cycles (Default)
0
1
0
2
4 machine cycles
0
1
1
3
5 machine cycles
1
0
0
4
6 machine cycles
1
0
1
5
7 machine cycles
1
1
0
6
8 machine cycles
1
1
1
7
9 machine cycles
Port 1
Bit:
7
6
5
4
3
2
1
0
P1.7
P1.6
P1.5
P1.4
P1.3
P1.2
P1.1
P1.0
Mnemonic: P1
Address: 90h
P1.7 − 0: General purpose I/O port. Most instructions will read the port pins in case of a port read
access, however in case of read-modify-write instructions, the port latch is read. Some pins
also have alternate input or output functions. This alternate functions are described below:
P1.0 : T2
External I/O for Timer/Counter 2
P1.1 : T2EX Timer/Counter 2 Capture/Reload Trigger
P1.2 : RXD1 Serial Port 1 Receive
P1.3 : TXD1 Serial Port 1 Transmit
P1.4 : INT2 External Interrupt 2
P1.5 : INT3 External Interrupt 3
P1.6 : INT4 External Interrupt 4
P1.7 : INT5 External Interrupt 5
External Interrupt Flag
Bit:
7
6
5
4
3
2
1
0
IE5
IE4
IE3
IE2
XT/RG
RGMD
RGSL
-
Mnemonic: EXIF
Address: 91h
IE5: External Interrupt 5 flag. Set by hardware when a falling edge is detected on INT5 .
IE4: External Interrupt 4 flag. Set by hardware when a rising edge is detected on INT4.
IE3: External Interrupt 3 flag. Set by hardware when a falling edge is detected on INT5 .
IE2: External Interrupt 2 flag. Set by hardware when a rising edge is detected on INT2.
- 16 -
Preliminary W77L32
XT/ RG RG: Crystal/RC Oscillator Select. Setting this bit selects crystal or external clock as system
clock source. Clearing this bit selects the on-chip RC oscillator as clock source.
XTUP(STATUS.4) must be set to 1 and XTOFF (PMR.3) must be cleared before this bit
can be set. Attempts to set this bit without obeying these conditions will be ignored. This
bit is set to 1 after a power-on reset and unchanged by other forms of reset.
RGMD: RC Mode Status. This bit indicates the current clock source of microcontroller. When cleared,
CPU is operating from the external crystal or oscillator. When set, CPU is operating from the
on-chip RC oscillator. This bit is cleared to 0 after a power-on reset and unchanged by other
forms of reset.
RGSL: RC Oscillator Select. This bit selects the clock source following a resume from Power Down
Mode. Setting this bit allows device operating from RC oscillator when a resume from Power
Down Mode. When this bit is cleared, the device will hold operation until the crystal oscillator
has warmed-up following a resume from Power Down Mode. This bit is cleared to 0 after a
power-on reset and unchanged by other forms of reset.
Serial Port Control
Bit:
7
6
5
4
3
2
1
0
SM0/FE
SM1
SM2
REN
TB8
RB8
TI
RI
Mnemonic: SCON
Address: 98h
SM0/FE: Serial port 0, Mode 0 bit or Framing Error Flag: The SMOD0 bit in PCON SFR determines
whether this bit acts as SM0 or as FE. The operation of SM0 is described below. When used
as FE, this bit will be set to indicate an invalid stop bit. This bit must be manually cleared in
software to clear the FE condition.
SM1:
Serial port Mode bit 1:
SM0
SM1
Mode
0
0
0
0
1
1
1
0
2
1
1
3
Description
Length
Synchronous
8
Asynchronous 10
Asynchronous 11
Asynchronous 11
Baud rate
4/12 Tclk
variable
64/32 Tclk
variable
SM2:
Multiple processors communication. Setting this bit to 1 enables the multiprocessor
communication feature in mode 2 and 3. In mode 2 or 3, if SM2 is set to 1, then RI will not be
activated if the received 9th data bit (RB8) is 0. In mode 1, if SM2 = 1, then RI will not be
activated if a valid stop bit was not received. In mode 0, the SM2 bit controls the serial port
clock. If set to 0, then the serial port runs at a divide by 12 clock of the oscillator. This gives
compatibility with the standard 8052. When set to 1, the serial clock become divide by 4 of the
oscillator clock. This results in faster synchronous serial communication.
REN:
Receive enable: When set to 1 serial reception is enabled, otherwise reception is disabled.
TB8:
This is the 9th bit to be transmitted in modes 2 and 3. This bit is set and cleared by software as
desired.
In modes 2 and 3 this is the received 9th data bit. In mode 1, if SM2 = 0, RB8 is the stop bit
that was received. In mode 0 it has no function.
Transmit interrupt flag: This flag is set by hardware at the end of the 8th bit time in mode 0, or
at the beginning of the stop bit in all other modes during serial transmission. This bit must be
cleared by software.
RB8:
TI:
- 17 -
Publication Release Date: November 2, 2001
Revision A1
Preliminary W77L32
RI:
Receive interrupt flag: This flag is set by hardware at the end of the 8th bit time in mode 0, or
halfway through the stop bits time in the other modes during serial reception. However the
restrictions of SM2 apply to this bit. This bit can be cleared only by software
Serial Data Buffer
Bit:
7
6
5
4
3
2
1
0
SBUF.7
SBUF.6
SBUF.5
SBUF.4
SBUF.3
SBUF.2
SBUF.1
SBUF.0
Mnemonic: SBUF
Address: 99h
SBUF.7 − 0: Serial data on the serial port 0 is read from or written to this location. It actually consists of
two separate internal 8-bit registers. One is the receive resister, and the other is the
transmit buffer. Any read access gets data from the receive data buffer, while write
access is to the transmit data buffer.
Port 2
Bit:
7
6
5
4
3
2
1
0
P2.7
P2.6
P2.5
P2.4
P2.3
P2.2
P2.1
P2.0
Mnemonic: P2
Address: A0h
P2.7 − 0: Port 2 is a bi-directional I/O port with internal pull-ups. This port also provides the upper
address bits for accesses to external memory.
Port 4
Bit:
7
6
5
4
3
2
1
0
-
-
-
-
P4.3
P4.2
P4.1
P4.0
Mnemonic: P4
Address: A5h
P4.3 − 0: Port 4 is a bi-directional I/O port with internal pull-ups.
Interrupt Enable
Bit:
7
6
5
4
3
2
1
0
EA
ES1
ET2
ES
ET1
EX1
ET0
EX0
Mnemonic: IE
EA:
ES1:
ET2:
ES:
ET1:
EX1:
ET0:
EX0:
Address: A8h
Global enable. Enable/disable all interrupts.
Enable Serial Port 1 interrupt.
Enable Timer 2 interrupt.
Enable Serial Port 0 interrupt.
Enable Timer 1 interrupt
Enable external interrupt 1
Enable Timer 0 interrupt
Enable external interrupt 0
- 18 -
Preliminary W77L32
Slave Address
Bit:
7
6
5
4
3
2
Mnemonic: SADDR
1
0
Address: A9h
SADDR: The SADDR should be programmed to the given or broadcast address for serial port 0 to
which the slave processor is designated.
Slave Address 1
Bit:
7
6
5
4
3
Mnemonic: SADDR1
2
1
0
Address: AAh
SADDR1: The SADDR1 should be programmed to the given or broadcast address for serial port 1 to
which the slave processor is designated.
Port 3
Bit:
7
6
5
4
3
2
1
0
P3.7
P3.6
P3.5
P3.4
P3.3
P3.2
P3.1
P3.0
Mnemonic: P3
Address: B0h
P3.7 − 0: General purpose I/O port. Each pin also has an alternate input or output function. The
alternate functions are described below.
P3.7
RD
Strobe for read from external RAM
P3.6
P3.5
P3.4
WR
T1
T0
Strobe for write to external RAM
Timer/counter 1 external count input
Timer/counter 0 external count input
P3.3
INT1
External interrupt 1
P3.2
P3.1
P3.0
INT0
TxD
RxD
External interrupt 0
Serial port 0 output
Serial port 0 input
Interrupt Priority
Bit:
7
6
5
4
3
2
1
0
-
PS1
PT2
PS
PT1
PX1
PT0
PX0
Mnemonic: IP
IP.7:
PS1:
PT2:
PS:
Address: B8h
This bit is un-implemented and will read high.
This bit defines the Serial port 1 interrupt priority. PS = 1 sets it to higher priority level.
This bit defines the Timer 2 interrupt priority.
PT2 = 1 sets it to higher priority level.
This bit defines the Serial port 0 interrupt priority. PS = 1 sets it to higher priority level.
- 19 -
Publication Release Date: November 2, 2001
Revision A1
Preliminary W77L32
PT1:
PX1:
PT0:
PX0:
This bit defines the Timer 1 interrupt priority.
This bit defines the External interrupt 1 priority.
This bit defines the Timer 0 interrupt priority.
This bit defines the External interrupt 0 priority.
PT1 = 1 sets it to higher priority level.
PX1 = 1 sets it to higher priority level.
PT0 = 1 sets it to higher priority level.
PX0 = 1 sets it to higher priority level.
Slave Address Mask Enable
Bit:
7
6
5
4
3
2
Mnemonic: SADEN
1
0
Address: B9h
SADEN: This register enables the Automatic Address Recognition feature of the Serial port 0. When a
bit in the SADEN is set to 1, the same bit location in SADDR will be compared with the
incoming serial data. When SADEN.n is 0, then the bit becomes a "don't care" in the
comparison. This register enables the Automatic Address Recognition feature of the Serial
port 0. When all the bits of SADEN are 0, interrupt will occur for any incoming address.
Slave Address Mask Enable 1
Bit:
7
6
5
4
3
Mnemonic: SADEN1
2
1
0
Address: BAh
SADEN1: This register enables the Automatic Address Recognition feature of the Serial port 1. When
a bit in the SADEN1 is set to 1, the same bit location in SADDR1 will be compared with the
incoming serial data. When SADEN1.n is 0, then the bit becomes a "don't care" in the
comparison. This register enables the Automatic Address Recognition feature of the Serial
port 1. When all the bits of SADEN1 are 0, interrupt will occur for any incoming address.
Serial Port Control 1
Bit:
7
6
5
4
3
2
1
0
SM0_1/FE_1
SM1_1
SM2_1
REN_1
TB8_1
RB8_1
TI_1
RI_1
Mnemonic: SCON1
Address: C0h
SM0_1/FE_1: Serial port 1, Mode 0 bit or Framing Error Flag 1: The SMOD0 bit in PCON SFR
determines whether this bit acts as SM0_1 or as FE_1. the operation of SM0_1 is
described below. When used as FE_1, this bit will be set to indicate an invalid stop bit.
This bit must be manually cleared in software to clear the FE_1 condition.
SM1_1: Serial port 1 Mode bit 1:
SM0_1
0
0
1
1
SM1_1
0
1
0
1
Mode
0
1
2
3
Description
Length
Synchronous
8
Asynchronous 10
Asynchronous 11
Asynchronous 11
- 20 -
Baud rate
4/12 Tclk
variable
64/32 Tclk
variable
Preliminary W77L32
SM2_1: Multiple processors communication. Setting this bit to 1 enables the multiprocessor
communication feature in mode 2 and 3. In mode 2 or 3, if SM2_1 is set to 1, then RI_1 will
not be activated if the received 9th data bit (RB8_1) is 0. In mode 1, if SM2_1 = 1, then RI_1
will not be activated if a valid stop bit was not received. In mode 0, the SM2_1 bit controls the
serial port 1 clock. If set to 0, then the serial port 1 runs at a divide by 12 clock of the
oscillator. This gives compatibility with the standard 8052. When set to 1, the serial clock
become divide by 4 of the oscillator clock. This results in faster synchronous serial
communication.
REN_1: Receive enable: When set to 1 serial reception is enabled, otherwise reception is disabled.
TB8_1: This is the 9th bit to be transmitted in modes 2 and 3. This bit is set and cleared by software as
desired.
RB8_1: In modes 2 and 3 this is the received 9th data bit. In mode 1, if SM2_1 = 0, RB8_1 is the stop
bit that was received. In mode 0 it has no function.
TI_1:
Transmit interrupt flag: This flag is set by hardware at the end of the 8th bit time in mode 0, or
at the beginning of the stop bit in all other modes during serial transmission. This bit must be
cleared by software.
RI_1:
Receive interrupt flag: This flag is set by hardware at the end of the 8th bit time in mode 0, or
halfway through the stop bits time in the other modes during serial reception. However the
restrictions of SM2_1 apply to this bit. This bit can be cleared only by software
Serial Data Buffer 1
Bit:
7
6
5
4
3
2
1
0
SBUF1.7
SBUF1.6
SBUF1.5
SBUF1.4
SBUF1.3
SBUF1.2
SBUF1.1
SBUF1.0
Mnemonic: SBUF1
Address: C1h
SBUF1.7 − 0: Serial data of the serial port 1 is read from or written to this location. It actually consists
of two separate 8-bit registers. One is the receive resister, and the other is the transmit
buffer. Any read access gets data from the receive data buffer, while write accesses are
to the transmit data buffer.
ROMMAP
Bit:
7
6
5
4
3
2
1
0
WS
1
-
-
-
-
-
-
Mnemonic: ROMMAP
Address: C2h
WS: Wait State Signal Enable. Setting this bit enables the WAIT signal on P4.0. The device will
sample the wait state control signal WAIT via P4.0 during MOVX instruction. This bit is time
access protected.
Power Management Register
Bit:
7
6
5
4
3
2
1
0
CD1
CD0
SWB
-
XTOFF
ALE-OFF
-
DME0
Mnemonic: PMR
Address: C4h
- 21 -
Publication Release Date: November 2, 2001
Revision A1
Preliminary W77L32
CD1, CD0: Clock Divide Control. These bit selects the number of clocks required to generate one
machine cycle. There are three modes including divide by 4, 64 or 1024. Switching
between modes must first go back devide by 4 mode. For instance, to go from 64 to 1024
clocks/machine cycle the device must first go from 64 to 4 clocks/machine cycle, and then
from 4 to 1024 clocks/machine cycle.
CD1,
0
0
1
1
SWB:
CD0
0
1
0
1
Clocks/machine cycle
Reserved
4
64
1024
Switchback Enable. Setting this bit allows an enabled external interrupt or serial port activity
to force the CD1,CD0 to divide by 4 state (0,1). The device will switch modes at the start of
the jump to interrupt service routine while a external interrupt is enabled and actually
recongnized by microcontroller. While a serial port reception, the switchback occurs at the
start of the instruction following the falling edge of the start bit.
XTOFF: Crystal Oscillator Disable. Setting this bit disables the external crystal oscillator. This bit can
only be set to 1 while the microcontroller is operating from the RC oscillator. Clearing this bit
restarts the crystal oscillator, the XTUP (STATUS.4) bit will be set after crystal oscillator
warmed-up has completed.
ALEOFF: This bit disables the expression of the ALE signal on the device pin during all on-board
program and data memory accesses. External memory accesses will automatically enable
ALE independent of ALEOFF.
0 = ALE expression is enable; 1 = ALE expression is disable
DME0:
This bit determines the on-chip MOVX SRAM to be enabled or disabled.
Set this bit to 1 will enable the on-chip 1KB MOVX SRAM.
Status Register
Bit:
7
6
5
4
3
2
1
0
-
HIP
LIP
XTUP
SPTA1
SPRA1
SPTA0
SPRA0
Mnemonic: STATUS
Address: C5h
HIP:
High Priority Interrupt Status. When set, it indicates that software is servicing a high priority
interrupt. This bit will be cleared when the program executes the corresponding RETI
instruction.
LIP:
Low Priority Interrupt Status. When set, it indicates that software is servicing a low priority
interrupt. This bit will be cleared when the program executes the corresponding RETI
instruction.
XTUP: Crystal Oscillator Warm-up Status. when set, this bit indicates CPU has detected clock to be
ready. Each time the crystal oscillator is restarted by exit from power down mode or the
XTOFF bit is set, hardware will clear this bit. This bit is set to 1 after a power-on reset. When
this bit is cleared, it prevents software from setting the XT/ RG bit to enable CPU operation
from crystal oscillator.
- 22 -
Preliminary W77L32
SPTA1: Serial Port 1 Transmit Activity. This bit is set during serial port 1 is currently transmitting data.
It is cleared when TI_1 bit is set by hardware. Changing the Clock Divide Control bits CD0,
CD1 will be ignored when this bit is set to 1 and SWB = 1.
SPRA1: Serial Port 1 Receive Activity. This bit is set during serial port 1 is currently receiving a data. It
is cleared when RI_1 bit is set by hardware. Changing the Clock Divide Control bits CD0, CD1
will be ignored when this bit is set to 1 and SWB = 1.
SPTA0: Serial Port 0 Transmit Activity. This bit is set during serial port 0 is currently transmitting data.
It is cleared when TI bit is set by hardware. Changing the Clock Divide Control bits CD0,CD1
will be ignored when this bit is set to 1 and SWB = 1.
SPRA0: Serial Port 0 Receive Activity. This bit is set during serial port 0 is currently receiving a data. It
is cleared when RI bit is set by hardware. Changing the Clock Divide Control bits CD0, CD1
will be ignored when this bit is set to 1 and SWB = 1.
Timed Access
Bit:
7
TA.7
6
TA.6
5
TA.5
4
TA.4
3
TA.3
2
TA.2
Mnemonic: TA
1
TA.1
0
TA.0
Address: C7h
TA: The Timed Access register controls the access to protected bits. To access protected bits, the
user must first write AAH to the TA. This must be immediately followed by a write of 55H to TA.
Now a window is opened in the protected bits for three machine cycles, during which the user can
write to these bits.
Timer 2 Control
Bit:
7
TF2
6
EXF2
5
RCLK
4
TCLK
Mnemonic: T2CON
3
EXEN2
2
TR2
1
0
C/ T2
CP/ RL2
Address: C8h
TF2:
Timer 2 overflow flag: This bit is set when Timer 2 overflows. It is also set when the count is
equal to the capture register in down count mode. It can be set only if RCLK and TCLK are
both 0. It is cleared only by software. Software can also set or clear this bit.
EXF2: Timer 2 External Flag: A negative transition on the T2EX pin (P1.1) or timer 2 overflow will
cause this flag to set based on the CP/RL2, EXEN2 and DCEN bits. If set by a negative
transition, this flag must be cleared by software. Setting this bit in software or detection of a
negative transition on T2EX pin will force a timer interrupt if enabled.
RCLK: Receive Clock Flag: This bit determines the serial port 0 time-base when receiving data in
serial modes 1 or 3. If it is 0, then timer 1 overflow is used for baud rate generation, otherwise
timer 2 overflow is used. Setting this bit forces timer 2 in baud rate generator mode.
TCLK: Transmit Clock Flag: This bit determines the serial port 0 time-base when transmitting data in
modes 1 and 3. If it is set to 0, the timer 1 overflow is used to generate the baud rate clock,
otherwise timer 2 overflow is used. Setting this bit forces timer 2 in baud rate generator mode.
EXEN2: Timer 2 External Enable. This bit enables the capture/reload function on the T2EX pin if Timer
2 is not generating baud clocks for the serial port. If this bit is 0, then the T2EX pin will be
ignored, otherwise a negative transition detected on the T2EX pin will result in capture or
reload.
TR2: Timer 2 Run Control. This bit enables/disables the operation of timer 2. Clearing this bit will
halt the timer 2 and preserve the current count in TH2, TL2.
- 23 -
Publication Release Date: November 2, 2001
Revision A1
Preliminary W77L32
C/ T2 : Counter/Timer Select. This bit determines whether timer 2 will function as a timer or a counter.
Independent of this bit, the timer will run at 2 clocks per tick when used in baud rate generator
mode. If it is set to 0, then timer 2 operates as a timer at a speed depending on T2M bit
(CKCON.5), otherwise it will count negative edges on T2 pin.
CP/ RL2 : Capture/Reload Select. This bit determines whether the capture or reload function will be
used for timer 2. If either RCLK or TCLK is set, this bit will be ignored and the timer will
function in an auto-reload mode following each overflow. If the bit is 0 then auto-reload will
occur when timer 2 overflows or a falling edge is detected on T2EX pin if EXEN2 = 1.
If this bit is 1, then timer 2 captures will occur when a falling edge is detected on T2EX pin if
EXEN2 = 1.
Timer 2 Mode Control
Bit:
7
6
5
4
3
2
1
0
HC5
HC4
HC3
HC2
T2CR
-
T2OE
DCEN
Mnemonic: T2MOD
Address: C9h
HC5:
Hardware Clear INT5 flag. Setting this bit allows the flag of external interrupt 5 to be
automatically cleared by hardware while entering the interrupt service routine.
HC4:
Hardware Clear INT4 flag. Setting this bit allows the flag of external interrupt 4 to be
automatically cleared by hardware while entering the interrupt service routine.
HC3:
Hardware Clear INT3 flag. Setting this bit allows the flag of external interrupt 3 to be
automatically cleared by hardware while entering the interrupt service routine.
HC3:
Hardware Clear INT2 flag. Setting this bit allows the flag of external interrupt 3 to be
automatically cleared by hardware while entering the interrupt service routine.
T2CR: Timer 2 Capture Reset. In the Timer 2 Capture Mode this bit enables/disables hardware
automatically reset Timer 2 while the value in TL2 and TH2 have been transferred into the
capture register.
T2OE: Timer 2 Output Enable. This bit enables/disables the Timer 2 clock out function.
DCEN: Down Count Enable: This bit, in conjunction with the T2EX pin, controls the direction that timer
2 counts in 16-bit auto-reload mode.
Timer 2 Capture LSB
Bit:
7
6
RCAP2L.7
RCAP2L.6
5
RCAP2L.5
4
3
2
1
0
RCAP2L.4
RCAP2L.3
RCAP2L.2
RCAP2L.1
RCAP2L.0
Mnemonic: RCAP2L
Address: CAh
RCAP2L: This register is used to capture the TL2 value when a timer 2 is configured in capture mode.
RCAP2L is also used as the LSB of a 16-bit reload value when timer 2 is configured in autoreload mode.
- 24 -
Preliminary W77L32
Timer 2 Capture MSB
Bit:
7
6
5
4
3
2
1
0
RCAP2H.7
RCAP2H.6
RCAP2H.5
RCAP2H.4
RCAP2H.3
RCAP2H.2
RCAP2H.1
RCAP2H.0
Mnemonic: RCAP2H
Address: CBh
RCAP2H: This register is used to capture the TH2 value when a timer 2 is configured in capture mode.
RCAP2H is also used as the MSB of a 16-bit reload value when timer 2 is configured in
auto-reload mode.
Timer 2 LSB
Bit:
7
6
5
4
3
2
1
0
TL2.7
TL2.6
TL2.5
TL2.4
TL2.3
TL2.2
TL2.1
TL2.0
Mnemonic: TL2
TL2:
Address: CCh
Timer 2 LSB
Timer 2 MSB
Bit:
7
6
5
4
3
2
1
0
TH2.7
TH2.6
TH2.5
TH2.4
TH2.3
TH2.2
TH2.1
TH2.0
Mnemonic: TH2
TH2:
Address: CDh
Timer 2 MSB
Program Status Word
Bit:
CY:
AC:
F0:
7
6
5
4
3
2
1
0
CY
AC
F0
RS1
RS0
OV
F1
P
Mnemonic: PSW
Address: D0h
Carry flag: Set for an arithmetic operation which results in a carry being generated from the
ALU. It is also used as the accumulator for the bit operations.
Auxiliary carry: Set when the previous operation resulted in a carry from the high order nibble.
User flag 0: General purpose flag that can be set or cleared by the user.
RS.1 − 0: Register bank select bits:
OV:
F1:
P:
RS1
RS0
Register bank
Address
0
0
0
00-07h
0
1
1
08-0Fh
1
0
2
10-17h
1
1
3
18-1Fh
Overflow flag: Set when a carry was generated from the seventh bit but not from the 8th bit as
a result of the previous operation, or vice-versa.
User Flag 1: General purpose flag that can be set or cleared by the user by software
Parity flag: Set/cleared by hardware to indicate odd/even number of 1's in the accumulator.
- 25 -
Publication Release Date: November 2, 2001
Revision A1
Preliminary W77L32
Watchdog Control
Bit:
7
6
5
4
3
2
1
0
SMOD_1
POR
-
-
WDIF
WTRF
EWT
RWT
Mnemonic: WDCON
Address: D8h
SMOD_1:This bit doubles the Serial Port 1 baud rate in mode 1, 2, and 3 when set to 1.
POR:
Power-on reset flag. Hardware will set this flag on a power up condition. This flag can be read
or written by software. A write by software is the only way to clear this bit once it is set.
WDIF: Watchdog Timer Interrupt Flag. If the watchdog interrupt is enabled, hardware will set this bit to
indicate that the watchdog interrupt has occurred. If the interrupt is not enabled, then this bit
indicates that the time-out period has elapsed. This bit must be cleared by software.
WTRF: Watchdog Timer Reset Flag. Hardware will set this bit when the watchdog timer causes a
reset. Software can read it but must clear it manually. A power-fail reset will also clear the bit.
This bit helps software in determining the cause of a reset. If EWT = 0, the watchdog timer will
have no affect on this bit.
EWT:
Enable Watchdog timer Reset. Setting this bit will enable the Watchdog timer Reset function.
RWT: Reset Watchdog Timer. This bit helps in putting the watchdog timer into a know state. It also
helps in resetting the watchdog timer before a time-out occurs. Failing to set the RWT before
time-out will cause an interrupt, if EWDI (EIE.4) is set, and 512 clocks after that a watchdog
timer reset will be generated if EWT is set. This bit is self-clearing by hardware.
The WDCON SFR is set to a 0x0x0xx0b on an external reset. WTRF is set to a 1 on a Watchdog timer
reset, but to a 0 on power on/down resets. WTRF is not altered by an external reset. POR is set to 1 by
a power-on reset. EWT is set to 0 on a Power-on reset and unaffected by other resets.
All the bits in this SFR have unrestricted read access. POR, EWT, WDIF and RWT require Timed
Access procedure to write. The remaining bits have unrestricted write accesses.
Accumulator
Bit:
7
6
5
4
3
2
1
0
ACC.7
ACC.6
ACC.5
ACC.4
ACC.3
ACC.2
ACC.1
ACC.0
Mnemonic: ACC
Address: E0h
ACC.7 − 0: The A (or ACC) register is the standard 8052 accumulator.
- 26 -
Preliminary W77L32
Extended Interrupt Enable
Bit:
7
6
5
4
3
2
1
0
-
-
-
EWDI
EX5
EX4
EX3
EX2
Mnemonic: EIE
Address: E8h
EIE.7 − 5: Reserved bits, will read high
EWDI: Enable Watchdog timer interrupt
EX5: External Interrupt 5 Enable.
EX4: External Interrupt 4 Enable.
EX3: External Interrupt 3 Enable.
EX2: External Interrupt 2 Enable.
B Register
Bit:
7
6
5
4
3
2
1
0
B.7
B.6
B.5
B.4
B.3
B.2
B.1
B.0
Mnemonic: B
Address: F0h
B.7 − 0: The B register is the standard 8052 register that serves as a second accumulator.
Extended Interrupt Priority
Bit:
7
6
5
4
3
2
1
0
-
-
-
PWDI
PX5
PX4
PX3
PX2
Mnemonic: EIP
Address: F8h
EIP.7 − 5: Reserved bits.
PWDI: Watchdog timer interrupt priority.
PX5:
External Interrupt 5 Priority. 0 = Low priority, 1 = High priority.
PX4:
External Interrupt 4 Priority. 0 = Low priority, 1 = High priority.
PX3:
External Interrupt 3 Priority. 0 = Low priority, 1 = High priority.
PX2:
External Interrupt 2 Priority. 0 = Low priority, 1 = High priority.
- 27 -
Publication Release Date: November 2, 2001
Revision A1
Preliminary W77L32
8. INSTRUCTION
The W77L32 executes all the instructions of the standard 8032 family. The operation of these
instructions, their effect on the flag bits and the status bits is exactly the same. However, timing of
these instructions is different. The reason for this is two fold. Firstly, in the W77L32, each machine
cycle consists of 4 clock periods, while in the standard 8032 it consists of 12 clock periods. Also, in the
W77L32 there is only one fetch per machine cycle i.e. 4 clocks per fetch, while in the standard 8032
there can be two fetches per machine cycle, which works out to 6 clocks per fetch.
The advantage the W77L32 has is that since there is only one fetch per machine cycle, the number of
machine cycles in most cases is equal to the number of operands that the instruction has. In case of
jumps and calls there will be an additional cycle that will be needed to calculate the new address. But
overall the W77L32 reduces the number of dummy fetches and wasted cycles, thereby improving
efficiency as compared to the standard 8032.
Table 2. Instructions that affect Flag settings
Instruction
Carry
Overflow
Auxiliary Carry
ADD
X
X
X
CLR C
0
ADDC
X
X
X
CPL C
X
SUBB
X
X
X
ANL C, bit
X
MUL
0
X
ANL C, bit
X
DIV
0
X
ORL C, bit
X
DA A
X
ORL C, bit
X
RRC A
X
MOV C, bit
X
RLC A
X
CJNE
X
SETB C
1
Instruction
Carry
Overflow
Auxiliary Carry
A "X" indicates that the modification is as per the result of instruction.
Table 3. Instruction Timing for W77L32
Instruction
HEX
Op-Code
Bytes
W77L32
Machine Cycles
W77L32
Clock Cycles
8032
Clock Cycles
W77L32 vs.8032
Speed Ratio
NOP
00
1
1
4
12
3
ADD A, R0
28
1
1
4
12
3
ADD A, R1
29
1
1
4
12
3
ADD A, R2
2A
1
1
4
12
3
ADD A, R3
2B
1
1
4
12
3
ADD A, R4
2C
1
1
4
12
3
ADD A, R5
2D
1
1
4
12
3
- 28 -
Preliminary W77L32
Table 3. Instruction Timing for W77L32, continued
Instruction
HEX
Op-Code
Bytes
W77L32
Machine Cycles
W77L32
Clock Cycles
8032
Clock Cycles
W77L32 vs.
8032 Speed Ratio
ADD A, R6
2E
1
1
4
12
3
ADD A, R7
2F
1
1
4
12
3
ADD A, @R0
26
1
1
4
12
3
ADD A, @R1
27
1
1
4
12
3
ADD A, direct
25
2
2
8
12
1.5
ADD A, #data
24
2
2
8
12
1.5
ADDC A, R0
38
1
1
4
12
3
ADDC A, R1
39
1
1
4
12
3
ADDC A, R2
3A
1
1
4
12
3
ADDC A, R3
3B
1
1
4
12
3
ADDC A, R4
3C
1
1
4
12
3
ADDC A, R5
3D
1
1
4
12
3
ADDC A, R6
3E
1
1
4
12
3
ADDC A, R7
3F
1
1
4
12
3
ADDC A, @R0
36
1
1
4
12
3
ADDC A, @R1
37
1
1
4
12
3
ADDC A, direct
35
2
2
8
12
1.5
ADDC A, #data
34
2
2
8
12
1.5
ACALL addr11
71, 91, B1, 11,
31, 51, D1, F1
2
3
12
24
2
AJMP ADDR11
01, 21, 41, 61,
81, A1, C1, E1
2
3
12
24
2
ANL A, R0
58
1
1
4
12
3
ANL A, R1
59
1
1
4
12
3
ANL A, R2
5A
1
1
4
12
3
ANL A, R3
5B
1
1
4
12
3
ANL A, R4
5C
1
1
4
12
3
ANL A, R5
5D
1
1
4
12
3
ANL A, R6
5E
1
1
4
12
3
ANL A, R7
5F
1
1
4
12
3
ANL A, @R0
56
1
1
4
12
3
ANL A, @R1
57
1
1
4
12
3
ANL A, direct
55
2
2
8
12
1.5
ANL A, #data
54
2
2
8
12
1.5
ANL direct, A
52
2
2
8
12
1.5
ANL direct, #data
53
3
3
12
24
2
ANL C, bit
82
2
2
8
24
3
ANL C, /bit
B0
2
2
8
24
3
CJNE A, direct, rel
B5
3
4
16
24
1.5
- 29 -
Publication Release Date: November 2, 2001
Revision A1
Preliminary W77L32
Table 3. Instruction Timing for W77L32, continued
Instruction
HEX
Op-Code
Bytes
W77L32
Machine Cycles
W77L32
Clock Cycles
8032
Clock Cycles
W77L32 vs.
8032 Speed Ratio
CJNE A, #data, rel
B4
3
4
16
24
1.5
CJNE @R0, #data, rel
B6
3
4
16
24
1.5
CJNE @R1, #data, rel
B7
3
4
16
24
1.5
CJNE R0, #data, rel
B8
3
4
16
24
1.5
CJNE R1, #data, rel
B9
3
4
16
24
1.5
CJNE R2, #data, rel
BA
3
4
16
24
1.5
CJNE R3, #data, rel
BB
3
4
16
24
1.5
CJNE R4, #data, rel
BC
3
4
16
24
1.5
CJNE R5, #data, rel
BD
3
4
16
24
1.5
CJNE R6, #data, rel
BE
3
4
16
24
1.5
CJNE R7, #data, rel
BF
3
4
16
24
1.5
CLR A
E4
1
1
4
12
3
CPL A
F4
1
1
4
12
3
CLR C
C3
1
1
4
12
3
CLR bit
C2
2
2
8
12
1.5
CPL C
B3
1
1
4
12
3
CPL bit
B2
2
2
8
12
1.5
DEC A
14
1
1
4
12
3
DEC R0
18
1
1
4
12
3
DEC R1
19
1
1
4
12
3
DEC R2
1A
1
1
4
12
3
DEC R3
1B
1
1
4
12
3
DEC R4
1C
1
1
4
12
3
DEC R5
1D
1
1
4
12
3
DEC R6
1E
1
1
4
12
3
DEC R7
1F
1
1
4
12
3
DEC @R0
16
1
1
4
12
3
DEC @R1
17
1
1
4
12
3
DEC direct
15
2
2
8
12
1.5
DEC DPTR
A5
1
2
8
-
-
DIV AB
84
1
5
20
48
2.4
DA A
D4
1
1
4
12
3
DJNZ R0, rel
D8
2
3
12
24
2
DJNZ R1, rel
D9
2
3
12
24
2
DJNZ R5, rel
DD
2
3
12
24
2
DJNZ R2, rel
DA
2
3
12
24
2
DJNZ R3, rel
DB
2
3
12
24
2
- 30 -
Preliminary W77L32
Table 3. Instruction Timing for W77L32, continued
Instruction
HEX
Op-Code
Bytes
W77L32
Machine Cycles
W77L32
Clock Cycles
8032
Clock Cycles
W77L32 vs.
8032 Speed Ratio
DJNZ R4, rel
DC
2
3
12
24
2
DJNZ R6, rel
DE
2
3
12
24
2
DJNZ R7, rel
DF
2
3
12
24
2
DJNZ direct, rel
D5
3
4
16
24
1.5
INC A
04
1
1
4
12
3
INC R0
08
1
1
4
12
3
INC R1
09
1
1
4
12
3
INC R2
0A
1
1
4
12
3
INC R3
0B
1
1
4
12
3
INC R4
0C
1
1
4
12
3
INC R5
0D
1
1
4
12
3
INC R6
0E
1
1
4
12
3
INC R7
0F
1
1
4
12
3
INC @R0
06
1
1
4
12
3
INC @R1
07
1
1
4
12
3
INC direct
05
2
2
8
12
1.5
INC DPTR
A3
1
2
8
24
3
JMP @A+DPTR
73
1
2
8
24
3
JZ rel
60
2
3
12
24
2
JNZ rel
70
2
3
12
24
2
JC rel
40
2
3
12
24
2
JNC rel
50
2
3
12
24
2
JB bit, rel
20
3
4
16
24
1.5
JNB bit, rel
30
3
4
16
24
1.5
JBC bit, rel
10
3
4
16
24
1.5
LCALL addr16
12
3
4
16
24
1.5
LJMP addr16
02
3
4
16
24
1.5
MUL AB
A4
1
5
20
48
2.4
MOV A, R0
E8
1
1
4
12
3
MOV A, R1
E9
1
1
4
12
3
MOV A, R2
EA
1
1
4
12
3
MOV A, R3
EB
1
1
4
12
3
MOV A, R4
EC
1
1
4
12
3
MOV A, R5
ED
1
1
4
12
3
MOV A, R6
EE
1
1
4
12
3
MOV A, R7
EF
1
1
4
12
3
MOV A, @R0
E6
1
1
4
12
3
MOV A, @R1
E7
1
1
4
12
3
- 31 -
Publication Release Date: November 2, 2001
Revision A1
Preliminary W77L32
Table 3. Instruction Timing for W77L32, continued
Instruction
HEX
Op-Code
Bytes
W77L32
Machine Cycles
W77L32
Clock Cycles
8032
Clock Cycles
W77L32 vs.
8032 Speed Ratio
MOV A, direct
E5
2
2
8
12
1.5
MOV A, #data
74
2
2
8
12
1.5
MOV R0, A
F8
1
1
4
12
3
MOV R1, A
F9
1
1
4
12
3
MOV R2, A
FA
1
1
4
12
3
MOV R3, A
FB
1
1
4
12
3
MOV R4, A
FC
1
1
4
12
3
MOV R5, A
FD
1
1
4
12
3
MOV R6, A
FE
1
1
4
12
3
MOV R7, A
FF
1
1
4
12
3
MOV R0, direct
A8
2
2
8
12
1.5
MOV R1, direct
A9
2
2
8
12
1.5
MOV R2, direct
AA
2
2
8
12
1.5
MOV R3, direct
AB
2
2
8
12
1.5
MOV R4, direct
AC
2
2
8
12
1.5
MOV R5, direct
AD
2
2
8
12
1.5
MOV R6, direct
AE
2
2
8
12
1.5
MOV R7, direct
AF
2
2
8
12
1.5
MOV R0, #data
78
2
2
8
12
1.5
MOV R1, #data
79
2
2
8
12
1.5
MOV R2, #data
7A
2
2
8
12
1.5
MOV R3, #data
7B
2
2
8
12
1.5
MOV R4, #data
7C
2
2
8
12
1.5
MOV R5, #data
7D
2
2
8
12
1.5
MOV R6, #data
7E
2
2
8
12
1.5
MOV R7, #data
7F
2
2
8
12
1.5
MOV @R0, A
F6
1
1
4
12
3
MOV @R1, A
F7
1
1
4
12
3
MOV @R0, direct
A6
2
2
8
12
1.5
MOV @R1, direct
A7
2
2
8
12
1.5
MOV @R0, #data
76
2
2
8
12
1.5
MOV @R1, #data
77
2
2
8
12
1.5
MOV direct, A
F5
2
2
8
12
1.5
MOV direct, R0
88
2
2
8
12
1.5
MOV direct, R1
89
2
2
8
12
1.5
MOV direct, R2
8A
2
2
8
12
1.5
MOV direct, R3
8B
2
2
8
12
1.5
- 32 -
Preliminary W77L32
Table 3. Instruction Timing for W77L32, continued
Instruction
HEX
Op-Code
Bytes
W77L32
Machine Cycles
W77L32
Clock Cycles
8032
Clock Cycles
W77L32 vs.
8032 Speed Ratio
MOV direct, R4
8C
2
2
8
12
1.5
MOV direct, R5
8D
2
2
8
12
1.5
MOV direct, R6
8E
2
2
8
12
1.5
MOV direct, R7
8F
2
2
8
12
1.5
MOV direct, @R0
86
2
2
8
12
1.5
MOV direct, @R1
87
2
2
8
12
1.5
MOV direct, direct
85
3
3
12
24
2
MOV direct, #data
75
3
3
12
24
2
MOV DPTR, #data 16
90
3
3
12
24
2
MOVC A, @A+DPTR
93
1
2
8
24
3
MOVC A, @A+PC
83
1
2
8
24
3
MOVX A, @R0
E2
1
2-9
8 - 36
24
3 - 0.66
MOVX A, @R1
E3
1
2-9
8 - 36
24
3 - 0.66
MOVX A, @DPTR
E0
1
2-9
8 - 36
24
3 - 0.66
MOVX @R0, A
F2
1
2-9
8 - 36
24
3 - 0.66
MOVX @R1, A
F3
1
2-9
8 - 36
24
3 - 0.66
MOVX @DPTR, A
F0
1
2-9
8 - 36
24
3 - 0.66
MOV C, bit
A2
2
2
8
12
1.5
MOV bit, C
92
2
2
8
24
3
ORL A, R0
48
1
1
4
12
3
ORL A, R1
49
1
1
4
12
3
ORL A, R2
4A
1
1
4
12
3
ORL A, R3
4B
1
1
4
12
3
ORL A, R4
4C
1
1
4
12
3
ORL A, R5
4D
1
1
4
12
3
ORL A, R6
4E
1
1
4
12
3
ORL A, R7
4F
1
1
4
12
3
ORL A, @R0
46
1
1
4
12
3
ORL A, @R1
47
1
1
4
12
3
ORL A, direct
45
2
2
8
12
1.5
ORL A, #data
44
2
2
8
12
1.5
ORL direct, A
42
2
2
8
12
1.5
ORL direct, #data
43
3
3
12
24
2
ORL C, bit
72
2
2
8
24
3
ORL C, /bit
A0
2
2
6
24
3
PUSH direct
C0
2
2
8
24
3
POP direct
D0
2
2
8
24
3
RET
22
1
2
8
24
3
- 33 -
Publication Release Date: November 2, 2001
Revision A1
Preliminary W77L32
Table 3. Instruction Timing for W77L32, continued
Instruction
HEX
Op-Code
Bytes
W77L32
Machine Cycles
W77L32
Clock Cycles
8032
Clock Cycles
W77L32 vs.
8032 Speed Ratio
RETI
32
1
2
8
24
3
RL A
23
1
1
4
12
3
RLC A
33
1
1
4
12
3
RR A
03
1
1
4
12
3
RRC A
13
1
1
4
12
3
SETB C
D3
1
1
4
12
3
SETB bit
D2
2
2
8
12
1.5
SWAP A
C4
1
1
4
12
3
SJMP rel
80
2
3
12
24
2
SUBB A, R0
98
1
1
4
12
3
SUBB A, R1
99
1
1
4
12
3
SUBB A, R2
9A
1
1
4
12
3
SUBB A, R3
9B
1
1
4
12
3
SUBB A, R4
9C
1
1
4
12
3
SUBB A, R5
9D
1
1
4
12
3
SUBB A, R6
9E
1
1
4
12
3
SUBB A, R7
9F
1
1
4
12
3
SUBB A, @R0
96
1
1
4
12
3
SUBB A, @R1
97
1
1
4
12
3
SUBB A, direct
95
2
2
8
12
1.5
SUBB A, #data
94
2
2
8
12
1.5
XCH A, R0
C8
1
1
4
12
3
XCH A, R1
C9
1
1
4
12
3
XCH A, R2
CA
1
1
4
12
3
XCH A, R3
CB
1
1
4
12
3
XCH A, R4
CC
1
1
4
12
3
XCH A, R5
CD
1
1
4
12
3
XCH A, R6
CE
1
1
4
12
3
XCH A, R7
CF
1
1
4
12
3
XCH A, @R0
C6
1
1
4
12
3
XCH A, @R1
C7
1
1
4
12
3
XCHD A, @R0
D6
1
1
4
12
3
XCHD A, @R1
D7
1
1
4
12
3
XCH A, direct
C5
2
2
8
12
1.5
XRL A, R0
68
1
1
4
12
3
XRL A, R1
69
1
1
4
12
3
XRL A, R2
6A
1
1
4
12
3
- 34 -
Preliminary W77L32
Table 3. Instruction Timing for W77L32, continued
Instruction
HEX
Op-Code
Bytes
W77L32
Machine Cycles
W77L32
Clock Cycles
8032
Clock Cycles
W77L32 vs.
8032 Speed Ratio
XRL A, R3
6B
1
1
4
12
3
XRL A, R4
6C
1
1
4
12
3
XRL A, R5
6D
1
1
4
12
3
XRL A, R6
6E
1
1
4
12
3
XRL A, R7
6F
1
1
4
12
3
XRL A, @R0
66
1
1
4
12
3
XRL A, @R1
67
1
1
4
12
3
XRL A, direct
65
2
2
8
12
1.5
XRL A, #data
64
2
2
8
12
1.5
XRL direct, A
62
2
2
8
12
1.5
XRL direct, #data
63
3
3
12
24
2
Intruction Timing
The instruction timing for the W77L32 is an important aspect, especially for those users who wish to
use software instructions to generate timing delays. Also, it provides the user with an insight into the
timing differences between the W77L32 and the standard 8032. In the W77L32 each machine cycle is
four clock periods long. Each clock period is designated a state. Thus each machine cycle is made up
of four states, C1, C2, C3 and C4 in that order. Due to the reduced time for each instruction execution,
both the clock edges are used for internal timing. Hence it is important that the duty cycle of the clock
be as close to 50% as possible to avoid timing conflicts. As mentioned earlier, the W77L32 does one
op-code fetch per machine cycle. Therefore, in most of the instructions, the number of machine cycles
needed to execute the instruction is equal to the number of bytes in the instruction. Of the 256
available op-codes, 128 of them are single cycle instructions. Thus more than half of all op-codes in
the W77L32 are executed in just four clock periods. Most of the two-cycle instructions are those that
have two byte instruction codes. However there are some instructions that have only one byte
instructions, yet they are two cycle instructions. One instruction which is of importance is the MOVX
instruction. In the standard 8032, the MOVX instruction is always two machine cycles long. However in
the W77L32, the user has a facility to stretch the duration of this instruction from 2 machine cycles to 9
machine cycles. The RD and WR strobe lines are also proportionately elongated. This gives the user
flexibility in accessing both fast and slow peripherals without the use of external circuitry and with
minimum software overhead. The rest of the instructions are either three, four or five machine cycle
instructions. Note that in the W77L32, based on the number of machine cycles, there are five different
types, while in the standard 8032 there are only three. However, in the W77L32 each machine cycle is
made of only 4 clock periods compared to the 12 clock periods for the standard 8032. Therefore, even
though the number of categories has increased, each instruction is at least 1.5 to 3 times faster than
the standard 8032 in terms of clock periods.
- 35 -
Publication Release Date: November 2, 2001
Revision A1
Preliminary W77L32
Single Cycle
C2
C1
C4
C3
CLK
ALE
PSEN
A7-0
AD7-0
PORT 2
Data_ in D7-0
Address A15-8
Figure 3: Single Cycle Instruction Timing
Operand Fetch
Instruction Fetch
C1
C2
C3
C4
C1
C2
C3
C4
CLK
ALE
PSEN
PC
AD7-0
OP-CODE
PC+1
Address A15-8
PORT 2
OPERAND
Address A15-8
Figure 4: Two Cycle Instruction Timing
Instruction Fetch
C1
C2
C3
Operand Fetch
C4
C1
C2
C3
Operand Fetch
C4
C1
C2
C3
C4
CLK
ALE
PSEN
AD7-0
PORT 2
A7-0
OP-CODE
Address A15-8
A7-0
OPERAND
Address A15-8
Figure 5: Three Cycle Instruction Timing
- 36 -
A7-0
OPERAND
Address A15-8
Preliminary W77L32
Instruction Fetch
C1
C2
C3
Operand Fetch
C4
C1
C2
C3
Operand Fetch
C4
C1
C2
C3
Operand Fetch
C4
C1
C2
C3
C4
CLK
ALE
PSEN
A7-0 OP-CODE
AD7-0
Port 2
A7-0
Address A15-8
A7-0
OPERAND
Address A15-8
A7-0 OPERAND
OPERAND
Address A15-8
Address A15-8
Figure 6: Four Cycle Instruction Timing
Instruction Fetch
C1
C2
C3
C4
Operand Fetch
C1
C2
C3
C4
Operand Fetch
C1
C2
C3
Operand Fetch
C4
C1
C2
C3
C4
Operand Fetch
C1
C2
C3
C4
CLK
ALE
PSEN
AD7-0
PORT 2
A7-0
OP-CODE
Address A15-8
A7-0 OPERAND
A7-0 OPERAND
A7-0 OPERAND
A7-0 OPERAND
Address A15-8
Address A15-8
Address A15-8
Address A15-8
Figure 7: Five Cycle Instruction Timing
- 37 -
Publication Release Date: November 2, 2001
Revision A1
Preliminary W77L32
MOVX Instruction
The W77L32, like the standard 8032, uses the MOVX instruction to access external Data Memory.
This Data Memory includes both off-chip memory as well as memory mapped peripherals. While the
results of the MOVX instruction are the same as in the standard 8032, the operation and the timing of
the strobe signals have been modified in order to give the user much greater flexibility.
The MOVX instruction is of two types, the MOVX @Ri and MOVX @DPTR. In the MOVX @Ri, the
address of the external data comes from two sources. The lower 8-bits of the address are stored in the
Ri register of the selected working register bank. The upper 8-bits of the address come from the port 2
SFR. In the MOVX @DPTR type, the full 16-bit address is supplied by the Data Pointer.
Since the W77L32 has two Data Pointers, DPTR and DPTR1, the user has to select between the two
by setting or clearing the DPS bit. The Data Pointer Select bit (DPS) is the LSB of the DPS SFR, which
exists at location 86h. No other bits in this SFR have any effect, and they are set to 0. When DPS is 0,
then DPTR is selected, and when set to 1, DPTR1 is selected. The user can switch between DPTR
and DPTR1 by toggling the DPS bit. The quickest way to do this is by the INC instruction. The
advantage of having two Data Pointers is most obvious while performing block move operations. The
accompanying code shows how the use of two separate Data Pointers speeds up the execution time
for code performing the same task.
Block Move with single Data Pointer:
; SH and SL are the high and low bytes of Source Address
; DH and DL are the high and low bytes of Destination Address
; CNT is the number of bytes to be moved
MOV
MOV
MOV
MOV
MOV
R2, #CNT
R3, #SL
R4, #SH
R5, #DL
R6, #DH
Machine cycles of W77L32
#
; Load R2 with the count value
2
; Save low byte of Source Address in R3
2
; Save high byte of Source address in R4
2
; Save low byte of Destination Address in R5
2
; Save high byte of Destination address in R6
2
LOOP:
MOV
MOV
MOVX
INC
MOV
MOV
MOV
MOV
MOVX
INC
MOV
MOV
DJNZ
DPL, R3
DPH, R4
A, @DPTR
DPTR
R3, DPL
R4, DPH
DPL, R5
DPH, R6
@DPTR, A
DPTR
DPL, R5
DPH, R6
R2, LOOP
; Load DPL with low byte of Source address
; Load DPH with high byte of Source address
; Get byte from Source to Accumulator
; Increment Source Address to next byte
; Save low byte of Source address in R3
; Save high byte of Source Address in R4
; Load low byte of Destination Address in DPL
; Load high byte of Destination Address in DPH
; Write data to destination
; Increment Destination Address
; Save low byte of new destination address in R5 2
; Save high byte of new destination address in R6
; Decrement count and do LOOP again if count <> 0
- 38 -
2
2
2
2
2
2
2
2
2
2
2
2
Preliminary W77L32
Machine cycles in standard 8032 = 10 + (26 * CNT)
Machine cycles in W77L32 = 10 + (26 * CNT)
If CNT = 50
Clock cycles in standard 8032= ((10 + (26 *50)) * 12 = (10 + 1300) * 12 = 15720
Clock cycles in W77L32 = ((10 + (26 * 50)) * 4 = (10 + 1300) * 4 = 5240
Block Move with Two Data Pointers in W77L32:
; SH and SL are the high and low bytes of Source Address
; DH and DL are the high and low bytes of Destination Address
; CNT is the number of bytes to be moved
MOV
MOV
MOV
INC
MOV
R2, #CNT
DPS, #00h
DPTR, #DHDL
DPS
DPTR, #SHSL
; Load R2 with the count value
; Clear DPS to point to DPTR
; Load DPTR with Destination address
; Set DPS to point to DPTR1
; Load DPTR1 with Source address
LOOP:
MOVX
INC
DEC
MOVX
INC
INC
DJNZ
A, @DPTR
DPTR
DPS
@DPTR, A
DPTR
DPS
R2, LOOP
; Get data from Source block
; Increment source address
; Clear DPS to point to DPTR
; Write data to Destination
; Increment destination address
; Set DPS to point to DPTR1
; Check if all done
Machine cycles of W77L32
#
2
2
3
2
3
2
2
2
2
2
2
3
Machine cycles in W77L32 = 12 + (15 * CNT)
If CNT = 50
Clock cycles in W77L32 = (12 + (15 * 50)) * 4 = (12 + 750) * 4 = 3048
We can see that in the first program the standard 8032 takes 15720 cycles, while the W77L32 takes
only 5240 cycles for the same code. In the second program, written for the W77L32, program
execution requires only 3048 clock cycles. If the size of the block is increased then the saving is even
greater.
External Data Memory Access Timing
The timing for the MOVX instruction is another feature of the W77L32. In the standard 8032, the
MOVX instruction has a fixed execution time of 2 machine cycles. However in the W77L32, the
duration of the access can be varied by the user.
The instruction starts off as a normal op-code fetch of 4 clocks. In the next machine cycle, the W77L32
puts out the address of the external Data Memory and the actual access occurs here. The user can
change the duration of this access time by setting the STRETCH value. The Clock Control SFR
(CKCON) has three bits that control the stretch value. These three bits are M2-0 (bits 2-0 of CKCON).
These three bits give the user 8 different access time options. The stretch can be varied from 0 to 7,
- 39 -
Publication Release Date: November 2, 2001
Revision A1
Preliminary W77L32
resulting in MOVX instructions that last from 2 to 9 machine cycles in length. Note that the stretching of
the instruction only results in the elongation of the MOVX instruction, as if the state of the CPU was
held for the desired period. There is no effect on any other instruction or its timing. By default, the
Stretch value is set at 1, giving a MOVX instruction of 3 machine cycles. If desired by the user the
stretch value can be set to 0 to give the fastest MOVX instruction of only 2 machine cycles.
Table 4. Data Memory Cycle Stretch Values
M2
M1
M0
Machine
Cycles
RD or WR
Strobe Width
in Clocks
RD or WR
Strobe Width
@25 MHz
RD or WR
Strobe Width
@40 MHz
0
0
0
2
2
80 nS
50 nS
0
0
1
3 (Default)
4
160 nS
100 nS
0
1
0
4
8
320 nS
200 nS
0
1
1
5
12
480 nS
300 nS
1
0
0
6
16
640 nS
400 nS
1
0
1
7
20
800 nS
500 nS
1
1
0
8
24
960 nS
600 nS
1
1
1
9
28
1120 nS
700 nS
Last Cycle
First
Second
of Previous
Instruction
Machine cycle
Machine cycle
Next Instruction
Machine Cycle
MOVX instruction cycle
C1 C2 C3 C4 C1 C2 C3 C4 C1 C2 C3 C4 C1 C2 C3 C4
CLK
ALE
PSEN
WR
PORT 0
A0-A7
A0-A7
D0-D7
Next Inst.
Address
MOVX Inst.
Address
MOVX Inst.
PORT 2
D0-D7
A15-A8
D0-D7
A0-A7
D0-D7
MOVX Data
Address
Next Inst. Read
MOVX Data out
A15-A8
A15-A8
Figure 8: Data Memory Write with Stretch Value = 0
- 40 -
A0-A7
A15-A8
Preliminary W77L32
Last Cycle
First
of Previous
Instruction
Second
Third
Machine Cycle Machine Cycle Machine Cycle
Next Instruction
Machine Cycle
MOVX instruction cycle
C1 C2 C3 C4 C1 C2 C3 C4 C1 C2 C3 C4 C1 C2 C3 C4 C1 C2 C3 C4
CLK
ALE
PSEN
WR
D0-D7
A0-A7
PORT 0
MOVX Inst.
Address
Next Inst.
Address
D0-D7
A0-A7
MOVX Data
Address
D0-D7
A0-A7
MOVX Data out
Next Inst.
Read
MOVX Inst.
PORT 2
D0-D7
A0-A7
A15-A8
A15-A8
A15-A8
A15-A8
Figure 9: Dada Memory Write with Stretch Value = 1
Last Cycle
First
Second
Third
Fourth
of Previous
Instruction
Machine Cycle
Machine Cycle
Machine Cycle
Machine Cycle
Next
Instruction
Machine Cycle
MOVX instruction cycle
C1 C2 C3 C4 C1 C2 C3 C4 C1 C2 C3 C4 C1 C2 C3 C4 C1 C2 C3 C4 C1 C2 C3 C4
CLK
ALE
PSEN
WR
PORT 0
D0-D7
A0-A7
A0-A7
D0-D7
A0-A7
MOVX Inst.
Address
Next Inst.
MOVX Data
Address
Address
Next Inst.
MOVX Inst.
Read
PORT 2
A15-A8
A15-A8
D0-D7
A0-A7
D0-D7
MOVX Data out
A15-A8
A15-A8
Figure 10: Dada Memory Write with Stretch Value = 2
- 41 -
Publication Release Date: November 2, 2001
Revision A1
Preliminary W77L32
Wait State Control Signal
Either with the software using stretch value to change the required machine cycle of MOVX instruction,
the W77L32 provides another hardware signal WAIT to implement the wider duration of external data
access timing. This wait state control signal is the alternate function of P4.0 such that it can only be
invoked to 44-pin PLCC/QFP package type. The wait state control signal can be enabled by setting
WS (ROMMAP.7) bit. When enabled, the setting of stretch value decides the minimum length of
MOVX instruction cycle and the device will sample the WAIT pin at each C3 state before the rising
edge of read/write strobe signal during MOVX instruction. Once this signal being recongnized, one
more machine cycle (wait state cycle) will be inserted into next cycle. The inserted wait state cycles are
unlimited, so the MOVX instruction cycle will end in which the wait state control signal is deactivated.
Using wait state control signal allows a dynamically access timimg to a selected external peripheral.
The WS bit is accessed by the Timed Access Protection procedure.
Wait State Control Signal Timing ( when Stretch = 1 )
Third
Machine
Cycle
Second
Machine
Cycle
First
Machine
Cycle
Wait-State
Cycle
MOVX Instruction
C1
C2 C3 C4
C1
C2 C3 C4
C1
C2 C3 C4
C1
C2 C3 C4 C1
C2 C3 C4
CLOCK
ALE
PSEN
ADDRESS
original rising edge
RD / WR
Extended duration
sample WAIT
sample
WAIT
WAIT
Wait State Control Signal Timing ( when Stretch = 2 )
Third
Machine
Cycle
Second
Machine
Cycle
First
Machine
Cycle
Fourth
Machine
Cycle
Wait-State
Cycle
MOVX Instruction
C1
C2 C3
C4
C1
C2 C3
C4
C1
C2 C3 C4
C1
C2 C3 C4
C1
C2 C3
C4
C1
CLOCK
ALE
PSEN
ADDRESS
original rising edge
RD / WR
Extended duration
sample
WAIT
WAIT
- 42 -
sample WAIT
C2
Preliminary W77L32
9. POWER MANAGEMENT
The W77L32 has several features that help the user to modify the power consumption of the device.
The power saving features are basically the POWER DOWN mode, ECONOMY mode and the IDLE
mode of operation.
Idle Mode
The user can put the device into idle mode by writing 1 to the bit PCON.0. The instruction that sets the
idle bit is the last instruction that will be executed before the device goes into Idle Mode. In the Idle
mode, the clock to the CPU is halted, but not to the Interrupt, Timer, Watchdog timer and Serial port
blocks. This forces the CPU state to be frozen; the Program counter, the Stack Pointer, the Program
Status Word, the Accumulator and the other registers hold their contents. The ALE and PSEN pins
are held high during the Idle state. The port pins hold the logical states they had at the time Idle was
activated. The Idle mode can be terminated in two ways. Since the interrupt controller is still active, the
activation of any enabled interrupt can wake up the processor. This will automatically clear the Idle bit,
terminate the Idle mode, and the Interrupt Service Routine (ISR) will be executed. After the ISR,
execution of the program will continue from the instruction which put the device into Idle mode.
The Idle mode can also be exited by activating the reset. The device can be put into reset either by
applying a high on the external RST pin, a Power on/fail reset condition or a Watchdog timer reset. The
external reset pin has to be held high for at least two machine cycles I.e. 8 clock periods to be
recognized as a valid reset. In the reset condition the program counter is reset to 0000h and all the
SFRs are set to the reset condition. Since the clock is already running there is no delay and execution
starts immediately. In the Idle mode, the Watchdog timer continues to run, and if enabled, a time-out
will cause a watchdog timer interrupt which will wake up the device. The software must reset the
Watchdog timer in order to preempt the reset which will occur after 512 clock periods of the time-out.
When the W77L32 is exiting from an Idle mode with a reset, the instruction following the one which put
the device into Idle mode is not executed. So there is no danger of unexpected writes.
Economy Mode
The power consumption of microcontroller relates to operating frequency. The W77L32 offers a
Economy mode to reduce the internal clock rate dynamically without external components. By default,
one machine cycle needs 4 clocks. In Economy mode, software can select 4, 64 or 1024 clocks per
machine cycle. It keeps the CPU operating at a acceptable speed but eliminates the power
consumption. In the Idle mode, the clock of the core logic is stopped, b+ut all clocked peripherals such
as watchdog timer are still running at a rate of clock/4. In the Economy mode, all clocked peripherals
run at the same reduced clocks rate as in core logic. So the Economy mode may provide a lower
power consumption than idle mode.
Software invokes the Economy mode by setting the appropriate bits in the SFRs. Setting the bits
CD0(PMR.6),CD1(PMR.7) decides the instruction cycle rate as below:
CD1
CD0
0
0
1
1
0
1
0
1
Clocks/Machine Cycle
Reserved
4 (default)
64
1024
- 43 -
Publication Release Date: November 2, 2001
Revision A1
Preliminary W77L32
The selection of instruction rate is going to take effect after a delay of one instruction cycle. Switching
to divide by 64 or 1024 mode must first go from divide by 4 mode. This means software can not switch
directly between clock/64 and clock/1024 mode. The CPU has to return clock/4 mode first, then go to
clock/64 or clock/1024 mode.
The W77L32 allows the user to use internal RC oscillator instead of external crystal. Setting the
XT/ RG bit (EXIF.3) selects the crystal or RC oscillator as the clock source. When invoking RC
oscillator in Economy mode, software may set the XTOFF bit to turn off the crystal amplifier for saving
power. The CPU would run at the clock rate of approximately 2−4 MHz divided by 4, 64 or 1024. The
RC oscillator is not precise so that can not be invoked to the operation which needs the accurate timebase such as serial communication. The RGMD(EXIF.2) indicates current clock source. When
switching the clock source, CPU needs one instruction cycle delay to take effect new setting. If crystal
amplifier is disabled and RC oscillator is present clock source, software must first clear the XTOFF bit
to turn on crystal amplifier before switch to crystal operation. Hardware will set the XTUP bit
(STATUS.4) once the crystal is warm-up and ready for use. It is unable to set XT/ RG bit to 1 if XTUP
= 0.
In Economy mode, the serial port can not receive/transmit data correctly because the baud rate is
changed. In some systems, the external interrupts may require the fastest process such that the
reducing of operating speed is restricted. In order to solve these dilemmas, the W77L32 offers a
switchback feature which allows the CPU back to clock/4 mode immediately when triggered by serial
operation or external interrupts. The switchback feature is enabled by setting the SWB bit (PMR.5). A
serial port reception/transmission or qualified external interrupt which is enabled and acknowledged
without block conditions will cause CPU to return to divide by 4 mode. For the serial port reception, a
switchback is generated by a falling edge associated with start bit if the serial port reception is enabled.
When a serial port transmission, an instruction which writes a byte of data to serial port buffer will
cause a switchback to ensure the correct transmission. The switchback feature is unaffected by serial
port interrupt flags. After a switchback is generated, the software can manually return the CPU to
Economy mode. Note that the modification of clock control bits CD0 and CD1 will be ignored during
serial port transmit/receive when switchback is enabled. The Watchdog timer reset, power-on/fail reset
or external reset will force the CPU to return to divide by 4 mode.
Power Down Mode
The device can be put into Power Down mode by writing 1 to bit PCON.1. The instruction that does this
will be the last instruction to be executed before the device goes into Power Down mode. In the Power
Down mode, all the clocks are stopped and the device comes to a halt. All activity is completely
stopped and the power consumption is reduced to the lowest possible value. In this state the ALE and
PSEN pins are pulled low. The port pins output the values held by their respective SFRs.
The W77L32 will exit the Power Down mode with a reset or by an external interrupt pin enabled as
level detect. An external reset can be used to exit the Power down state. The high on RST pin
terminates the Power Down mode, and restarts the clock. The program execution will restart from
0000h. In the Power down mode, the clock is stopped, so the Watchdog timer cannot be used to
provide the reset to exit Power down mode.
The W77L32 can be woken from the Power Down mode by forcing an external interrupt pin activated,
provided the corresponding interrupt is enabled, while the global enable(EA) bit is set and the external
input has been set to a level detect mode. If these conditions are met, then the low level on the
external pin re-starts the oscillator. Then device executes the interrupt service routine for the
corresponding external interrupt. After the interrupt service routine is completed, the program
execution returns to the instruction after the one which put the device into Power Down mode and
continues from there. When RGSL(EXIF.1) bit is set to 1, the CPU will use the internal RC oscillator
- 44 -
Preliminary W77L32
instead of crystal to exit Power Down mode. The microcontroller will automatically switch from RC
oscillator to crystal after clock is stable. The RC oscillator runs at approximately 2−4 MHz. Using RC
oscillator to exit from Power Down mode saves the time for waiting crystal start-up. It is useful in the
low power system which usually be awakened from a short operation then returns to Power Down
mode.
Table 5. Status of external pins during Idle and Power Down
MODE
PROGRAM
MEMORY
ALE
PSEN
PORT0
PORT1
PORT2
PORT3
Idle
Internal
1
1
Data
Data
Data
Data
Idle
External
1
1
Float
Data
Address
Data
Power Down
Internal
0
0
Data
Data
Data
Data
Power Down
External
0
0
Float
Data
Data
Data
10. RESET CONDITIONS
The user has several hardware related options for placing the W77L32 into reset condition. In general,
most register bits go to their reset value irrespective of the reset condition, but there are a few flags
whose state depends on the source of reset. The user can use these flags to determine the cause of
reset using software. There are ways of putting the device into reset state, external reset and watchdog
reset.
External Reset
The device continuously samples the RST pin at state C4 of every machine cycle. Therefore the RST
pin must be held for at least 2 machine cycles to ensure detection of a valid RST high. The reset
circuitry then synchronously applies the internal reset signal. Thus the reset is a synchronous operation
and requires the clock to be running to cause an external reset.
Once the device is in reset condition, it will remain so as long as RST is 1. Even after RST is
deactivated, the device will continue to be in reset state for up to two machine cycles, and then begin
program execution from 0000h. There is no flag associated with the external reset condition. However
since the other two reset sources have flags, the external reset can be considered as the default reset
if those two flags are cleared.
Watchdog Timer Reset
The Watchdog timer is a free running timer with programmable time-out intervals. The user can clear
the watchdog timer at any time, causing it to restart the count. When the time-out interval is reached an
interrupt flag is set. If the Watchdog reset is enabled and the watchdog timer is not cleared, then 512
clocks from the flag being set, the watchdog timer will generate a reset . This places the device into the
reset condition. The reset condition is maintained by hardware for two machine cycles. Once the reset
is removed the device will begin execution from 0000h.
- 45 -
Publication Release Date: November 2, 2001
Revision A1
Preliminary W77L32
Reset State
Most of the SFRs and registers on the device will go to the same condition in the reset state. The
Program Counter is forced to 0000h and is held there as long as the reset condition is applied.
However, the reset state does not affect the on-chip RAM. The data in the RAM will be preserved
during the reset. However, the stack pointer is reset to 07h, and therefore the stack contents will be
lost. The RAM contents will be lost if the VDD falls below approximately 2V, as this is the minimum
voltage level required for the RAM to operate normally. Therefore after a first time power on reset the
RAM contents will be indeterminate. During a power fail condition, if the power falls below 2V, the RAM
contents are lost. Hence it should be assumed that after a power fail, the RAM contents are lost.
After a reset most SFRs are cleared. Interrupts and Timers are disabled. The Watchdog timer is
disabled if the reset source was a POR. The port SFRs have FFh written into them which puts the port
pins in a high state. Port 0 floats as it does not have on-chip pull-ups.
Table 6. SFR Reset Value
SFR NAME
RESET VALUE
SFR NAME
RESET VALUE
P0
11111111b
IE
00000000b
SP
00000111b
SADDR
00000000b
DPL
00000000b
P3
11111111b
DPH
00000000b
IP
x0000000b
DPL1
00000000b
SADEN
00000000b
DPH1
00000000b
T2CON
00000000b
DPS
00000000b
T2MOD
00000x00b
PCON
00xx0000b
RCAP2L
00000000b
TCON
00000000b
RCAP2H
00000000b
TMOD
00000000b
TL2
00000000b
TL0
00000000b
TH2
00000000b
TL1
00000000b
TA
11111111b
TH0
00000000b
PSW
00000000b
TH1
00000000b
WDCON
0x0x0xx0b
CKCON
00000001b
ACC
00000000b
P1
11111111b
EIE
xxx00000b
SCON
00000000b
B
00000000b
SBUF
xxxxxxxxb
EIP
xxx00000b
P2
11111111b
PC
00000000b
SADDR1
00000000b
SADEN1
00000000b
SCON1
00000000b
SBUF1
xxxxxxxxb
ROMMAP
01xxxxxxb
PMR
010xx0x0b
EXIF
0000xxx0b
STATUS
000x0000b
P4
xxxx1111b
- 46 -
Preliminary W77L32
The WDCON SFR bits are set/cleared in reset condition depending on the source of the reset.
WDCON
External reset
Watchdog reset
Power on reset
0x0x0xx0b
0x0x01x0b
01000000b
The POR bit WDCON.6 is set only by the power on reset. The WTRF bit WDCON.2 is set when the
Watchdog timer causes a reset. A power on reset will also clear this bit. The EWT bit WDCON.1 is
cleared by power on resets. This disables the Watchdog timer resets. A watchdog or external reset
does not affect the EWT bit.
11. INTERRUPTS
The W77L32 has a two priority level interrupt structure with 12 interrupt sources. Each of the interrupt
sources has an individual priority bit, flag, interrupt vector and enable bit. In addition, the interrupts can
be globally enabled or disabled.
Interrupt Sources
The External Interrupts INT0 and INT1 can be either edge triggered or level triggered, depending on
bits IT0 and IT1. The bits IE0 and IE1 in the TCON register are the flags which are checked to
generate the interrupt. In the edge triggered mode, the INTx inputs are sampled in every machine
cycle. If the sample is high in one cycle and low in the next, then a high to low transition is detected and
the interrupts request flag IEx in TCON or EXIF is set. The flag bit requests the interrupt. Since the
external interrupts are sampled every machine cycle, they have to be held high or low for at least one
complete machine cycle. The IEx flag is automatically cleared when the service routine is called. If the
level triggered mode is selected, then the requesting source has to hold the pin low till the interrupt is
serviced. The IEx flag will not be cleared by the hardware on entering the service routine. If the
interrupt continues to be held low even after the service routine is completed, then the processor may
acknowledge another interrupt request from the same source. Note that the external interrupts INT2 to
INT5 are edge triggered only. By default, the individual interrupt flag corresponding to external
interrupt 2 to 5 must be cleared manually by software. It can be configured with hardware cleared by
setting the corresponding bit HCx in the T2MOD register. For instance, if HC2 is set hardware will clear
IE2 flag after program enters the interrupt 2 service routine.
The Timer 0 and 1 Interrupts are generated by the TF0 and TF1 flags. These flags are set by the
overflow in the Timer 0 and Timer 1. The TF0 and TF1 flags are automatically cleared by the hardware
when the timer interrupt is serviced. The Timer 2 interrupt is generated by a logical OR of the TF2 and
the EXF2 flags. These flags are set by overflow or capture/reload events in the timer 2 operation. The
hardware does not clear these flags when a timer 2 interrupt is executed. Software has to resolve the
cause of the interrupt between TF2 and EXF2 and clear the appropriate flag.
The Watchdog timer can be used as a system monitor or a simple timer. In either case, when the timeout count is reached, the Watchdog timer interrupt flag WDIF (WDCON.3) is set. If the interrupt is
enabled by the enable bit EIE.4, then an interrupt will occur.
The Serial block can generate interrupts on reception or transmission. There are two interrupt sources
from the Serial block, which are obtained by the RI and TI bits in the SCON SFR and RI_1 and TI_1 in
the SCON1 SFR. These bits are not automatically cleared by the hardware, and the user will have to
clear these bits using software.
- 47 -
Publication Release Date: November 2, 2001
Revision A1
Preliminary W77L32
All the bits that generate interrupts can be set or reset by hardware, and thereby software initiated
interrupts can be generated. Each of the individual interrupts can be enabled or disabled by setting or
clearing a bit in the IE SFR. IE also has a global enable/disable bit EA, which can be cleared to disable
all the interrupt, at once.
Priority Level Structure
There are two priority levels for the interrupts, high and low. The interrupt source can be individually set
to either high or low levels. Naturally, a higher priority interrupt cannot be interrupted by a lower priority
interrupt. However there exists a pre-defined hierarchy amongst the interrupts themselves. This
hierarchy comes into play when the interrupt controller has to resolve simultaneous requests having
the same priority level. This hierarchy is defined as shown below; the interrupts are numbered starting
from the highest priority to the lowest.
Table 7. Priority structure of interrupts
SOURCE
External Interrupt 0
Timer 0 Overflow
External Interrupt 1
Timer 1 Overflow
Serial Port
Timer 2 Overflow
Serial Port 1
External Interrupt 2
External Interrupt 3
External Interrupt 4
External Interrupt 5
Watchdog Timer
FLAG
IE0
TF0
IE1
TF1
RI + TI
TF2 + EXF2
RI_1 + TI_1
IE2
IE3
IE4
IE5
WDIF
PRIORITY LEVEL
1 (highest)
2
3
4
5
6
7
8
9
10
11
12 (lowest)
The interrupt flags are sampled every machine cycle. In the same machine cycle, the sampled
interrupts are polled and their priority is resolved. If certain conditions are met then the hardware will
execute an internally generated LCALL instruction which will vector the process to the appropriate
interrupt vector address. The conditions for generating the LCALL are
1. An interrupt of equal or higher priority is not currently being serviced.
2. The current polling cycle is the last machine cycle of the instruction currently being executed.
3. The current instruction does not involve a write to IP, IE, EIP or EIE registers and is not a RETI.
If any of these conditions are not met, then the LCALL will not be generated. The polling cycle is
repeated every machine cycle, with the interrupts sampled in the same machine cycle. If an interrupt
flag is active in one cycle but not responded to, and is not active when the above conditions are met,
the denied interrupt will not be serviced. This means that active interrupts are not remembered; every
polling cycle is new.
The processor responds to a valid interrupt by executing an LCALL instruction to the appropriate
service routine. This may or may not clear the flag which caused the interrupt. In case of Timer
interrupts, the TF0 or TF1 flags are cleared by hardware whenever the processor vectors to the
- 48 -
Preliminary W77L32
appropriate timer service routine. In case of external interrupt, INT0 and INT1, the flags are cleared
only if they are edge triggered. In case of Serial interrupts, the flags are not cleared by hardware. In the
case of Timer 2 interrupt, the flags are not cleared by hardware. Watchdog timer interrupt flag WDIF
have to be cleared by software. The hardware LCALL behaves exactly like the software LCALL
instruction. This instruction saves the Program Counter contents onto the Stack, but does not save the
Program Status Word PSW. The PC is reloaded with the vector address of that interrupt which caused
the LCALL. These vector address for the different sources are as follows.
Table 8. Vector locations for interrupt sources
SOURCE
VECTOR ADDRESS
SOURCE
VECTOR ADDRESS
Timer 0 Overflow
000Bh
External Interrupt 0
0003h
Timer 1 Overflow
001Bh
External Interrupt 1
0013h
Timer 2 Interrupt
002Bh
Serial Port
0023h
External Interrupt 2
0043h
Serial Port 1
003Bh
External Interrupt 4
0053h
External Interrupt 3
004Bh
Watchdog Timer
0063h
External Interrupt 5
005Bh
The vector table is not evenly spaced; this is to accommodate future expansions to the device family.
Execution continues from the vectored address till an RETI instruction is executed. On execution of the
RETI instruction the processor pops the Stack and loads the PC with the contents at the top of the
stack. The user must take care that the status of the stack is restored to what is was after the
hardware LCALL, if the execution is to return to the interrupted program. The processor does not
notice anything if the stack contents are modified and will proceed with execution from the address put
back into PC. Note that a RET instruction would perform exactly the same process as a RETI
instruction, but it would not inform the Interrupt Controller that the interrupt service routine is
completed, and would leave the controller still thinking that the service routine is underway.
Interrupt Response Time
The response time for each interrupt source depends on several factors, such as the nature of the
interrupt and the instruction underway. In the case of external interrupts INT0 to INT5 , they are
sampled at C3 of every machine cycle and then their corresponding interrupt flags IEx will be set or
reset. The Timer 0 and 1 overflow flags are set at C3 of the machine cycle in which overflow has
occurred. These flag values are polled only in the next machine cycle. If a request is active and all
three conditions are met, then the hardware generated LCALL is executed. This LCALL itself takes
four machine cycles to be completed. Thus there is a minimum time of five machine cycles between
the interrupt flag being set and the interrupt service routine being executed.
A longer response time should be anticipated if any of the three conditions are not met. If a higher or
equal priority is being serviced, then the interrupt latency time obviously depends on the nature of the
service routine currently being executed. If the polling cycle is not the last machine cycle of the
instruction being executed, then an additional delay is introduced. The maximum response time (if no
other interrupt is in service) occurs if the W77L32 is performing a write to IE, IP, EIE or EIP and then
executes a MUL or DIV instruction. From the time an interrupt source is activated, the longest reaction
time is 12 machine cycles. This includes 1 machine cycle to detect the interrupt, 2 machine cycles to
- 49 -
Publication Release Date: November 2, 2001
Revision A1
Preliminary W77L32
complete the IE, IP, EIE or EIP access, 5 machine cycles to complete the MUL or DIV instruction and 4
machine cycles to complete the hardware LCALL to the interrupt vector location.
Thus in a single-interrupt system the interrupt response time will always be more than 5 machine
cycles and not more than 12 machine cycles. The maximum latency of 12 machine cycle is 48 clock
cycles. Note that in the standard 8051 the maximum latency is 8 machine cycles which equals 96
machine cycles. This is a 50% reduction in terms of clock periods.
12. PROGRAMMABLE TIMERS/COUNTERS
The W77L32 has three 16-bit programmable timer/counters and one programmable Watchdog timer.
The Watchdog timer is operationally quite different from the other two timers.
Timer/Counters 0 & 1
The W77L32 has two 16-bit Timer/Counters. Each of these Timer/Counters has two 8 bit registers
which form the 16 bit counting register. For Timer/Counter 0 they are TH0, the upper 8 bits register,
and TL0, the lower 8 bit register. Similarly Timer/Counter 1 has two 8 bit registers, TH1 and TL1. The
two can be configured to operate either as timers, counting machine cycles or as counters counting
external inputs.
When configured as a "Timer", the timer counts clock cycles. The timer clock can be programmed to
be thought of as 1/12 of the system clock or 1/4 of the system clock. In the "Counter" mode, the
register is incremented on the falling edge of the external input pin, T0 in case of Timer 0, and T1 for
Timer 1. The T0 and T1 inputs are sampled in every machine cycle at C4. If the sampled value is high
in one machine cycle and low in the next, then a valid high to low transition on the pin is recognized
and the count register is incremented. Since it takes two machine cycles to recognize a negative
transition on the pin, the maximum rate at which counting will take place is 1/24 of the master clock
frequency. In either the "Timer" or "Counter" mode, the count register will be updated at C3. Therefore,
in the "Timer" mode, the recognized negative transition on pin T0 and T1 can cause the count register
value to be updated only in the machine cycle following the one in which the negative edge was
detected.
The "Timer" or "Counter" function is selected by the "C/ T " bit in the TMOD Special Function Register.
Each Timer/Counter has one selection bit for its own; bit 2 of TMOD selects the function for
Timer/Counter 0 and bit 6 of TMOD selects the function for Timer/Counter 1. In addition each
Timer/Counter can be set to operate in any one of four possible modes. The mode selection is done by
bits M0 and M1 in the TMOD SFR.
Time-base Selection
The W77L32 gives the user two modes of operation for the timer. The timers can be programmed to
operate like the standard 8051 family, counting at the rate of 1/12 of the clock speed. This will ensure
that timing loops on the W77L32 and the standard 8051 can be matched. This is the default mode of
operation of the W77L32 timers. The user also has the option to count in the turbo mode, where the
timers will increment at the rate of 1/4 clock speed. This will straight-away increase the counting speed
three times. This selection is done by the T0M and T1M bits in CKCON SFR. A reset sets these bits to
0, and the timers then operate in the standard 8051 mode. The user should set these bits to 1 if the
timers are to operate in turbo mode.
- 50 -
Preliminary W77L32
Mode 0
In Mode 0, the timer/counters act as a 8 bit counter with a 5 bit, divide by 32 pre-scale. In this mode we
have a 13 bit timer/counter. The 13 bit counter consists of 8 bits of THx and 5 lower bits of TLx. The
upper 3 bits of TLx are ignored.
The negative edge of the clock increments the count in the TLx register. When the fifth bit in TLx
moves from 1 to 0, then the count in the THx register is incremented. When the count in THx moves
from FFh to 00h, then the overflow flag TFx in TCON SFR is set. The counted input is enabled only if
TRx is set and either GATE = 0 or INTx = 1. When C/ T is set to 0, then it will count clock cycles, and
if C/ T is set to 1, then it will count 1 to 0 transitions on T0 (P3.4) for timer 0 and T1 (P3.5) for timer 1.
When the 13 bit count reaches 1FFFh the next count will cause it to roll-over to 0000h. The timer
overflow flag TFx of the relevant timer is set and if enabled an interrupts will occur. Note that when
used as a timer, the time-base may be either clock cycles/12 or clock cycles/4 as selected by the bits
TxM of the CKCON SFR.
Clock Source
Mode
input
1/4
div. by 4
osc/1
div. by 64
osc/16
div. by 1024 osc/256
1/12
T0 = P3.4
(T1 = P3.5)
Timer 1 functions are shown in brackets
T0M = CKCON.3
(T1M = CKCON.4)
1
0
M1,M0 = TMOD.1,TMOD.0
(M1,M0 = TMOD.5,TMOD.4)
C/T = TMOD.2
(C/T = TMOD.6)
00
0
0
1
4
7
0
01
TL0
(TL1)
TR0 = TCON.4
(TR1 = TCON.6)
GATE = TMOD.3
(GATE = TMOD.7)
INT0 = P3.2
(INT1 = P3.3)
TFx
7
TH0
(TH1)
Interrupt
TF0
(TF1)
Figure 11: Timer/Counter Mode 0 & Mode 1
Mode 1
Mode 1 is similar to Mode 0 except that the counting register forms a 16 bit counter, rather than a 13
bit counter. This means that all the bits of THx and TLx are used. Roll-over occurs when the timer
moves from a count of FFFFh to 0000h. The timer overflow flag TFx of the relevant timer is set and if
enabled an interrupt will occur. The selection of the time-base in the timer mode is similar to that in
Mode 0. The gate function operates similarly to that in Mode 0.
Mode 2
In Mode 2, the timer/counter is in the Auto Reload Mode. In this mode, TLx acts as a 8 bit count
register, while THx holds the reload value. When the TLx register overflows from FFh to 00h, the TFx
bit in TCON is set and TLx is reloaded with the contents of THx, and the counting process continues
from here. The reload operation leaves the contents of the THx register unchanged. Counting is
enabled by the TRx bit and proper setting of GATE and INTx pins. As in the other two modes 0 and 1,
mode 2 allows counting of either clock cycles (clock/12 or clock/4) or pulses on pin Tn.
- 51 -
Publication Release Date: November 2, 2001
Revision A1
Preliminary W77L32
Clock Source
Mode
input
div. by 4
osc/1
div. by 64
osc/16
div. by 1024 osc/256
T0M = CKCON.3
(T1M = CKCON.4)
1/4
1/12
1
0
Timer 1 functions are shown in brackets
C/T = TMOD.2
(C/T = TMOD.6)
0
0
1
T0 = P3.4
(T1 = P3.5)
TL0
(TL1)
7
TFx
Interrupt
TF0
(TF1)
TR0 = TCON.4
(TR1 = TCON.6)
GATE = TMOD.3
(GATE = TMOD.7)
0
7
TH0
(TH1)
INT0 = P3.2
(INT1 = P3.3)
Figure 12: Timer/Counter Mode 2
Mode 3
Mode 3 has different operating methods for the two timer/counters. For timer/counter 1, mode 3 simply
freezes the counter. Timer/Counter 0, however, configures TL0 and TH0 as two separate 8 bit count
registers in this mode. The logic for this mode is shown in the figure. TL0 uses the Timer/Counter 0
control bits C/ T , GATE, TR0, INTx and TF0. The TL0 can be used to count clock cycles (clock/12 or
clock/4) or 1-to-0 transitions on pin T0 as determined by C/ T (TMOD.2). TH0 is forced as a clock
cycle counter (clock/12 or clock/4) and takes over the use of TR1 and TF1 from Timer/Counter 1.
Mode 3 is used in cases where an extra 8 bit timer is needed. With Timer 0 in Mode 3, Timer 1 can still
be used in Modes 0, 1 and 2., but its flexibility is somewhat limited. While its basic functionality is
maintained, it no longer has control over its overflow flag TF1 and the enable bit TR1. Timer 1 can still
be used as a timer/counter and retains the use of GATE and INT1 pin. In this condition it can be turned
on and off by switching it out of and into its own Mode 3. It can also be used as a baud rate generator
for the serial port.
Clock Source
Mode
input
div. by 4
osc/1
div. by 64
osc/16
div. by 1024 osc/256
T0 = P3.4
T0M = CKCON.3
1/4
1/12
1
C/T = TMOD.2
0
TL0
0
0
1
7
TF0
Interrupt
TR0 = TCON.4
GATE = TMOD.3
INT0 = P3.2
TH0
0
TR1 = TCON.6
Figure 13. Timer/Counter 0 Mode 3
- 52 -
7
TF1
Interrupt
Preliminary W77L32
Timer/Counter 2
Timer/Counter 2 is a 16 bit up/down counter which is configured by the T2MOD register and controlled
by the T2CON register. Timer/Counter 2 is equipped with a capture/reload capability. As with the Timer
0 and Timer 1 counters, there exists considerable flexibility in selecting and controlling the clock, and in
defining the operating mode. The clock source for Timer/Counter 2 may be selected for either the
external T2 pin (C/ T2 = 1) or the crystal oscillator, which is divided by 12 or 4 (C/ T2 = 0). The clock is
then enabled when TR2 is a 1, and disabled when TR2 is a 0.
Capture Mode
The capture mode is enabled by setting the CP/ RL2 bit in the T2CON register to a 1. In the capture
mode, Timer/Counter 2 serves as a 16 bit up counter. When the counter rolls over from FFFFh to
0000h, the TF2 bit is set, which will generate an interrupt request. If the EXEN2 bit is set, then a
negative transition of T2EX pin will cause the value in the TL2 and TH2 register to be captured by the
RCAP2L and RCAP2H registers. This action also causes the EXF2 bit in T2CON to be set, which will
also generate an interrupt. Setting the T2CR bit (T2MOD.3), the W77L32 allows hardware to reset
timer 2 automatically after the value of TL2 and TH2 have been captured.
Clock Source
Mode
input
1/4
div. by 4
osc/1
div. by 64
osc/16
div. by 1024 osc/256
1/12
T2M = CKCON.5
1
C/T2 = T2CON.1
0
T2CON.7
0
TL2
1
TH2
TF2
T2 = P1.0
TR2 = T2CON.2
Timer 2
Interrupt
T2EX = P1.1
RCAP2L RCAP2H
L
EXEN2 = T2CON.3
HH
EXF2
T2CON.6
Figure 14. 16-Bit Capture Mode
Auto-reload Mode, Counting Up
The auto-reload mode as an up counter is enabled by clearing the CP/ RL2 bit in the T2CON register
and clearing the DCEN bit in T2MOD register. In this mode, Timer/Counter 2 is a 16 bit up counter.
When the counter rolls over from FFFFh, a reload is generated that causes the contents of the
RCAP2L and RCAP2H registers to be reloaded into the TL2 and TH2 registers. The reload action also
sets the TF2 bit. If the EXEN2 bit is set, then a negative transition of T2EX pin will also cause a reload.
This action also sets the EXF2 bit in T2CON.
- 53 -
Publication Release Date: November 2, 2001
Revision A1
Preliminary W77L32
T2M = CKCON.5
Clock Source
Mode
input
1/4
1
div. by 4
osc/1
div. by 64
osc/16
div. by 1024 osc/256
1/12
0
C/T2 = T2CON.1
0
T2CON.7
TL2
1
TH2
TF2
T2 = P1.0
TR2 = T2CON.2
Timer 2
Interrupt
T2EX = P1.1
RCAP2L RCAP2H
L
EXEN2 = T2CON.3
EXF2
T2CON.6
Figure 15. 16-Bit Auto-reload Mode, Counting Up
Auto-reload Mode, Counting Up/Down
Timer/Counter 2 will be in auto-reload mode as an up/down counter if CP/ RL2 bit in T2CON is cleared
and the DCEN bit in T2MOD is set. In this mode, Timer/Counter 2 is an up/down counter whose
direction is controlled by the T2EX pin. A 1 on this pin cause the counter to count up. An overflow while
counting up will cause the counter to be reloaded with the contents of the capture registers. The next
down count following the case where the contents of Timer/Counter equal the capture registers will
load an FFFFh into Timer/Counter 2. In either event a reload will set the TF2 bit. A reload will also
toggle the EXF2 bit. However, the EXF2 bit can not generate an interrupt while in this mode.
Down Counting Reload Value
0FFh
T2M = CKCON.5
Clock Source
Mode
input
1/4
div. by 4
osc/1
div. by 64
osc/16
div. by 1024 osc/256
1/12
1
0FFh
C/T = T2CON.1
0
T2CON.7
0
TL2
1
TH2
TF2
Timer 2
Interrupt
T2 = P1.0
TR2 = T2CON.2
RCAP2L
T2EX = P1.1
RCAP2H
Up Counting Reload
Value
DCEN = 1
Figure 16. 16-Bit Auto-reload Up/Down Counter
- 54 -
EXF2
T2CON.6
Preliminary W77L32
Baud Rate Generator Mode
The baud rate generator mode is enabled by setting either the RCLK or TCLK bits in T2CON register.
While in the baud rate generator mode, Timer/Counter 2 is a 16 bit counter with auto reload when the
count rolls over from FFFFh. However, rolling over does not set the TF2 bit. If EXEN2 bit is set, then a
negative transition of the T2EX pin will set EXF2 bit in the T2CON register and cause an interrupt
request.
Clock Source
Mode
input
C/T = T2CON.1
div. by 4
osc/2
div. by 64
osc/32
div. by 1024 osc/512
0
TL2
1
Timer 2
overflow
TH2
T2 = P1.0
TR2 = T2CON.2
T2EX = P1.1
RCAP2L RCAP2H
EXF2
T2CON.6
EXEN2 = T2CON.3
Timer 2
Interrupt
Figure 17. Baud Rate Generator Mode
Programmable Clock-out
Timer 2 is equipped with a new clock-out feature which outputs a 50% duty cycle clock on P1.0. It can
be invoked as a programmable clock generator. To configure Timer 2 with clock-out mode, software
must initiate it by setting bit T2OE = 1, C/T2 = 0 and CP/RL = 0. Setting bit TR2 will start the timer. This
mode is similar to the baud rate generator mode, it will not generate an interrupt while Timer 2
overflow. So it is possible to use Timer 2 as a baud rate generator and a clock generator at the same
time. The clock-out frequency is determined by the following equation:
The Clock-out Frequency = Oscillator Frequency / [4 X (RCAP2H, RCAP2L) ]
Clock Source
Mode
input
div. by 4
osc/2
div. by 64
osc/32
div. by 1024 osc/512
TL2
TH2
1/2
T2=P1.0
TR2 = T2CON.2
T2EX = P1.1
RCAP2L RCAP2H
EXF2
T2CON.6
EXEN2 = T2CON.3
Timer 2
Interrupt
Figure 18. Programmable Clock-Out Mode
- 55 -
Publication Release Date: November 2, 2001
Revision A1
Preliminary W77L32
Watchdog Timer
The Watchdog timer is a free-running timer which can be programmed by the user to serve as a
system monitor, a time-base generator or an event timer. It is basically a set of dividers that divide the
system clock. The divider output is selectable and determines the time-out interval. When the time-out
occurs a flag is set, which can cause an interrupt if enabled, and a system reset can also be caused if
it is enabled. The interrupt will occur if the individual interrupt enable and the global enable are set. The
interrupt and reset functions are independent of each other and may be used separately or together
depending on the users software.
0
16
WD1,WD0
Clock Source
Mode
input
div. by 4
osc/1
div. by 64
osc/16
div. by 1024 osc/256
WDIF
17
19
EWDI(EIE.4)
00
01
20
22
10
11
WTRF
Time-out
512 clock
delay
Reset Watchdog
RWT (WDCON.0)
23
25
Interrupt
Reset
Enable Watchdog timer reset
EWT(WDCON.1)
Figure 19. Watchdog Timer
The Watchdog timer should first be restarted by using RWT. This ensures that the timer starts from a
known state. The RWT bit is used to restart the watchdog timer. This bit is self clearing, i.e. after
writing a 1 to this bit the software will automatically clear it. The watchdog timer will now count clock
cycles. The time-out interval is selected by the two bits WD1 and WD0 (CKCON.7 and CKCON.6).
When the selected time-out occurs, the Watchdog interrupt flag WDIF (WDCON.3) is set. After the
time-out has occurred, the watchdog timer waits for an additional 512 clock cycles. If the Watchdog
Reset EWT (WDCON.1) is enabled, then 512 clocks after the time-out, if there is no RWT, a system
reset due to Watchdog timer will occur. This will last for two machine cycles, and the Watchdog timer
reset flag WTRF (WDCON.2) will be set. This indicates to the software that the watchdog was the
cause of the reset.
When used as a simple timer, the reset and interrupt functions are disabled. The timer will set the
WDIF flag each time the timer completes the selected time interval. The WDIF flag is polled to detect a
time-out and the RWT allows software to restart the timer. The Watchdog timer can also be used as a
very long timer. The interrupt feature is enabled in this case. Every time the time-out occurs an
interrupt will occur if the global interrupt enable EA is set.
The main use of the Watchdog timer is as a system monitor. This is important in real-time control
applications. In case of some power glitches or electro-magnetic interference, the processor may begin
to execute errant code. If this is left unchecked the entire system may crash. Using the watchdog timer
interrupt during software development will allow the user to select ideal watchdog reset locations. The
code is first written without the watchdog interrupt or reset. Then the watchdog interrupt is enabled to
identify code locations where interrupt occurs. The user can now insert instructions to reset the
watchdog timer which will allow the code to run without any watchdog timer interrupts. Now the
watchdog timer reset is enabled and the watchdog interrupt may be disabled,. If any errant code is
- 56 -
Preliminary W77L32
executed now, then the reset watchdog timer instructions will not be executed at the required instants
and watchdog reset will occur.
The watchdog time-out selection will result in different time-out values depending on the clock speed.
The reset, when enabled, will occur 512 clocks after the time-out has occurred.
Table 9. Time-out values for the Watchdog timer
WD1
WD0
0
0
WATCHDOGIN
TERVAL
NUMBER OF
CLOCKS
2
17
131072
TIME
@1.8432 MHz
TIME
@10 MHz
71.11 mS
13.11 mS
TIME
@25 MHz
5.24 mS
0
1
2
20
1048576
568.89 mS
104.86 mS
41.94 mS
1
0
2
23
8388608
4551.11 mS
838.86 mS
335.54 mS
1
1
2
26
67108864
36408.88 mS
6710.89 mS
2684.35 mS
The Watchdog timer will de disabled by a power-on/fail reset. The Watchdog timer reset does not
disable the watchdog timer, but will restart it. In general, software should restart the timer to put it into a
known state.
The control bits that support the Watchdog timer are discussed below.
WATCHDOG CONTROL
WDIF: WDCON.3 - Watchdog Timer Interrupt flag. This bit is set whenever the time-out occurs in the
watchdog timer. If the Watchdog interrupt is enabled (EIE.4), then an interrupt will occur (if the
global interrupt enable is set and other interrupt requirements are met). Software or any reset
can clear this bit.
WTRF: WDCON.2 - Watchdog Timer Reset flag. This bit is set whenever a watchdog reset occurs.
This bit is useful for determined the cause of a reset. Software must read it, and clear it
manually. A Power-fail reset will clear this bit. If EWT = 0, then this bit will not be affected by
the watchdog timer.
EWT:
WDCON.1 - Enable Watchdog timer Reset. This bit when set to 1 will enable the Watchdog
timer reset function. Setting this bit to 0 will disable the Watchdog timer reset function, but will
leave the timer running
RWT: WDCON.0 - Reset Watchdog Timer. This bit is used to clear the Watchdog timer and to restart
it. This bit is self-clearing, so after the software writes 1 to it the hardware will automatically
clear it. If the Watchdog timer reset is enabled, then the RWT has to be set by the user within
512 clocks of the time-out. If this is not done then a Watchdog timer reset will occur.
CLOCK CONTROL
WD1, WD0: CKCON.7, CKCON.6 - Watchdog Timer Mode select bits. These two bits select the timeout interval for the watchdog timer. The reset time is 512 clock longer than the interrupt
time-out value.
17
The default Watchdog time-out is 2 clocks, which is the shortest time-out period. The EWT, WDIF
and RWT bits are protected by the Timed Access procedure. This prevents software from accidentally
enabling or disabling the watchdog timer. More importantly, it makes it highly improbable that errant
code can enable or disable the watchdog timer.
- 57 -
Publication Release Date: November 2, 2001
Revision A1
Preliminary W77L32
Serial Port
Serial port in the W77L32 is a full duplex port. The W77L32 provides the user with additional features
such as the Frame Error Detection and the Automatic Address Recognition. The serial ports are
capable of synchronous as well as asynchronous communication. In Synchronous mode the W77L32
generates the clock and operates in a half duplex mode. In the asynchronous mode, full duplex
operation is available. This means that it can simultaneously transmit and receive data. The transmit
register and the receive buffer are both addressed as SBUF Special Function Register. However any
write to SBUF will be to the transmit register, while a read from SBUF will be from the receive buffer
register. The serial port can operate in four different modes as described below.
Mode 0
This mode provides synchronous communication with external devices. In this mode serial data is
transmitted and received on the RXD line. TXD is used to transmit the shift clock. The TxD clock is
provided by the W77L32 whether the device is transmitting or receiving. This mode is therefore a half
duplex mode of serial communication. In this mode, 8 bits are transmitted or received per frame. The
LSB is transmitted/received first. The baud rate is fixed at 1/12 or 1/4 of the oscillator frequency. This
baud rate is determined by the SM2 bit (SCON.5). When this bit is set to 0, then the serial port runs at
1/12 of the clock. When set to 1, the serial port runs at 1/4 of the clock. This additional facility of
programmable baud rate in mode 0 is the only difference between the standard 8051 and the W77L32.
The functional block diagram is shown below. Data enters and leaves the Serial port on the RxD line.
The TxD line is used to output the shift clock. The shift clock is used to shift data into and out of the
W77L32 and the device at the other end of the line. Any instruction that causes a write to SBUF will
start the transmission. The shift clock will be activated and data will be shifted out on the RxD pin till all
8 bits are transmitted. If SM2 = 1, then the data on RxD will appear 1 clock period before the falling
edge of shift clock on TxD. The clock on TxD then remains low for 2 clock periods, and then goes high
again. If SM2 = 0, the data on RxD will appear 3 clock periods before the falling edge of shift clock on
TxD. The clock on TxD then remains low for 6 clock periods, and then goes high again. This ensures
that at the receiving end the data on RxD line can either be clocked on the rising edge of the shift clock
on TxD or latched when the TxD clock is low.
Clock Source
Mode
input
div. by 4
osc/1
div. by 64
osc/16
div. by 1024 osc/256
Internal
Data Bus
Write to
SBUF
÷12
÷4
TX SHIFT
TX START
1
Transmit Shift Register
Serial Port Interrupt
RI
CONTROLLER
RX
CLOCK
RI
REN
RXD
P3.0 Alternate
Output Function
TI
SERIAL
0
SOUT
LOAD
CLOCK
TX CLOCK
SM2
PARIN
RX
START
SHIFT
CLOCK
TXD
P3.1 Alternate
Output function
LOAD SBUF
RX SHIFT
Read SBUF
RXD
P3.0 Alternate
Iutput function
CLOCK
SBUF
PAROUT
SIN
Receive Shift Register
Figure 20. Serial Port Mode 0
- 58 -
SBUF
Internal
Data Bus
Preliminary W77L32
The TI flag is set high in C1 following the end of transmission of the last bit. The serial port will receive
data when REN is 1 and RI is zero. The shift clock (TxD) will be activated and the serial port will latch
data on the rising edge of shift clock. The external device should therefore present data on the falling
edge on the shift clock. This process continues till all the 8 bits have been received. The RI flag is set
in C1 following the last rising edge of the shift clock on TxD. This will stop reception, till the RI is
cleared by software.
Mode 1
In Mode 1, the full duplex asynchronous mode is used. Serial communication frames are made up of
10 bits transmitted on TXD and received on RXD. The 10 bits consist of a start bit (0), 8 data bits (LSB
first), and a stop bit (1). On receive, the stop bit goes into RB8 in the SFR SCON. The baud rate in this
mode is variable. The serial baud can be programmed to be 1/16 or 1/32 of the Timer 1 overflow.
Since the Timer 1 can be set to different reload values, a wide variation in baud rates is possible.
Transmission begins with a write to SBUF. The serial data is brought out on to TxD pin at C1 following
the first roll-over of divide by 16 counter. The next bit is placed on TxD pin at C1 following the next
rollover of the divide by 16 counter. Thus the transmission is synchronized to the divide by 16 counter
and not directly to the write to SBUF signal. After all 8 bits of data are transmitted, the stop bit is
transmitted. The TI flag is set in the C1 state after the stop bit has been put out on TxD pin. This will be
at the 10th rollover of the divide by 16 counter after a write to SBUF.
Reception is enabled only if REN is high. The serial port actually starts the receiving of serial data, with
the detection of a falling edge on the RxD pin. The 1-to-0 detector continuously monitors the RxD line,
sampling it at the rate of 16 times the selected baud rate. When a falling edge is detected, the divide
by 16 counter is immediately reset. This helps to align the bit boundaries with the rollovers of the divide
by 16 counter.
The 16 states of the counter effectively divide the bit time into 16 slices. The bit detection is done on a
best of three basis. The bit detector samples the RxD pin, at the 8th, 9th and 10th counter states. By
using a majority 2 of 3 voting system, the bit value is selected. This is done to improve the noise
rejection feature of the serial port. If the first bit detected after the falling edge of RxD pin is not 0, then
this indicates an invalid start bit, and the reception is immediately aborted. The serial port again looks
for a falling edge in the RxD line. If a valid start bit is detected, then the rest of the bits are also
detected and shifted into the SBUF.
After shifting in 8 data bits, there is one more shift to do, after which the SBUF and RB8 are loaded
and RI is set. However certain conditions must be met before the loading and setting of RI can be
done.
1. RI must be 0 and
2. Either SM2 = 0, or the received stop bit = 1.
If these conditions are met, then the stop bit goes to RB8, the 8 data bits go into SBUF and RI is set.
Otherwise the received frame may be lost. After the middle of the stop bit, the receiver goes back to
looking for a 1-to-0 transition on the RxD pin.
- 59 -
Publication Release Date: November 2, 2001
Revision A1
Preliminary W77L32
Timer 1
Overflow
Transmit Shift Register
Timer 2 Overflow
(for Serial Port 0 only)
STOP
Write to
SBUF
÷2
SMOD=
(SMOD_1) 0
TCLK
PARIN
START
LOAD
0
0
SOUT
1
1
÷16
Γ ∼
SAMPLE
1-TO-0
DETECTOR
ϖ
TX START
TX SHIFT
TX CLOCK
λ _; Φ
TI
SERIAL
CONTROLLER
Serial Port
Interrupt
RI
RX CLOCK
RX
START
LOAD
SBUF
RX SHIFT
Read
SBUF
CLOCK
PAROUT
RXD
TXD
CLOCK
1
÷16
ς ϖ
RCLK
Internal
Data Bus
BIT
DETECTOR
SIN
D8
SBUF
RB8
Internal
Data
Bus
Receive Shift Register
Figure 21: Serial Port Mode
Mode 2
This mode uses a total of 11 bits in asynchronous full-duplex communication. The functional
description is shown in the figure below. The frame consists of one start bit (0), 8 data bits (LSB first), a
programmable 9th bit (TB8) and a stop bit (0). The 9th bit received is put into RB8. The baud rate is
programmable to 1/32 or 1/64 of the oscillator frequency, which is determined by the SMOD bit in
PCON SFR. Transmission begins with a write to SBUF. The serial data is brought out on to TxD pin at
C1 following the first roll-over of the divide by 16 counter. The next bit is placed on TxD pin at C1
following the next rollover of the divide by 16 counter. Thus the transmission is synchronized to the
divide by 16 counter, and not directly to the write to SBUF signal. After all 9 bits of data are transmitted,
the stop bit is transmitted. The TI flag is set in the C1 state after the stop bit has been put out on TxD
pin. This will be at the 11th rollover of the divide by 16 counter after a write to SBUF. Reception is
enabled only if REN is high. The serial port actually starts the receiving of serial data, with the detection
of a falling edge on the RxD pin. The 1-to-0 detector continuously monitors the RxD line, sampling it at
the rate of 16 times the selected baud rate. When a falling edge is detected, the divide by 16 counter is
immediately reset. This helps to align the bit boundaries with the rollovers of the divide by 16 counter.
The 16 states of the counter effectively divide the bit time into 16 slices. The bit detection is done on a
best of three basis. The bit detector samples the RxD pin, at the 8th, 9th and 10th counter states. By
using a majority 2 of 3 voting system, the bit value is selected. This is done to improve the noise
rejection feature of the serial port. If the first bit detected after the falling edge of RxD pin, is not 0, then
this indicates an invalid start bit, and the reception is immediately aborted. The serial port again looks
for a falling edge in the RxD line. If a valid start bit is detected, then the rest of the bits are also
detected and shifted into the SBUF. After shifting in 9 data bits, there is one more shift to do, after
- 60 -
Preliminary W77L32
which the SBUF and RB8 are loaded and RI is set. However certain conditions must be met before the
loading and setting of RI can be done.
1. RI must be 0 and
2. Either SM2 = 0, or the received stop bit = 1.
If these conditions are met, then the stop bit goes to RB8, the 8 data bits go into SBUF and RI is set.
Otherwise the received frame may be lost. After the middle of the stop bit, the receiver goes back to
looking for a 1-to-0 transition on the RxD pin.
Clock Source
Mode
input
div. by 4
osc/2
div. by 64
osc/32
div. by 1024 osc/512
TB8
Write to
SBUF
÷2
SMOD=
(SMOD_1)
0
D8
STOP
Internal
Data Bus
PARIN
TXD
START SOUT
LOAD
1
T
CLOCK
÷16
÷16
TX
SHIFT
TX START
TX CLOCK
Transmit Shift Register
TI
SERIAL
CONTROLLER
Serial Port
Interrupt
RI
RX CLOCK
SAMPLE
1-TO-0
DETECTOR
RX START
LOAD
SBUF
RX SHIFT
Read
SBUF
CLOCK
PAROUT
RXD
BIT
DETECTOR
SIN
D8
SBUF
RB8
Internal
Data
Bus
Receive Shift Register
Figure 22. Serial Port Mode 2
- 61 -
Publication Release Date: November 2, 2001
Revision A1
Preliminary W77L32
Mode 3
This mode is similar to Mode 2 in all respects, except that the baud rate is programmable. The user
must first initialize the Serial related SFR SCON before any communication can take place. This
involves selection of the Mode and baud rate. The Timer 1 should also be initialized if modes 1 and 3
are used. In all four modes, transmission is started by any instruction that uses SBUF as a destination
register. Reception is initiated in Mode 0 by the condition RI = 0 and REN = 1. This will generate a
clock on the TxD pin and shift in 8 bits on the RxD pin. Reception is initiated in the other modes by the
incoming start bit if REN = 1. The external device will start the communication by transmitting the start
bit.
Table 10. Serial Ports Modes
SM1
SM0
MODE
TYPE
BAUD CLOCK
FRAME
SIZE
START
BIT
STOP
BIT
9TH BIT
FUNCTION
0
0
0
Synch.
4 or 12 TCLKs
8 bits
No
No
None
0
1
1
Asynch.
Timer 1 or 2
10 bits
1
1
None
1
0
2
Asynch.
32 or 64 TCLKs
11 bits
1
1
0, 1
1
1
3
Asynch.
Timer 1 or 2
11 bits
1
1
0, 1
Timer 1
Overflow
Timer 2 Overflow
(for Serial Port 0 only)
SMOD=
(SMOD_1) 0
PARIN
START
LOAD
0
0
SOUT
TXD
CLOCK
1
TX START
1
÷16
RCLK
D8
Internal
Data Bus
Write to
SBUF
÷2
TCLK
STOP
TB8
1
÷16
Transmit Shift Register
TX SHIFT
TX CLOCK
TI
SERIAL
CONTROLLER
Serial Port
Interrupt
RI
RX CLOCK
SAMPLE
1-TO-0
DETECTOR
LOAD
SBUF
RX
START
Read
SBUF
RX SHIFT
CLOCK
PAROUT
RXD
BIT
DETECTOR
SIN
D8
Receive Shift Register
Figure 23: Serial Port Mode 3
- 62 -
SBUF
RB8
Internal
Data
Bus
Preliminary W77L32
Framing Error Detection
A Frame Error occurs when a valid stop bit is not detected. This could indicate incorrect serial data
communication. Typically the frame error is due to noise and contention on the serial communication
line. The W77L32 has the facility to detect such framing errors and set a flag which can be checked by
software.
The Frame Error FE(FE_1) bit is located in SCON.7(SCON1.7). This bit is normally used as SM0 in the
standard 8051 family. However, in the W77L32 it serves a dual function and is called SM0/FE
(SM0_1/FE_1). There are actually two separate flags, one for SM0 and the other for FE. The flag that
is actually accessed as SCON.7(SCON1.7) is determined by SMOD0 (PCON.6) bit. When SMOD0 is
set to 1, then the FE flag is indicated in SM0/FE. When SMOD0 is set to 0, then the SM0 flag is
indicated in SM0/FE.
The FE bit is set to 1 by hardware but must be cleared by software. Note that SMOD0 must be 1 while
reading or writing to FE or FE_1. If FE is set, then any following frames received without any error will
not clear the FE flag. The clearing has to be done by software.
Multiprocessor Communications
Multiprocessor communications makes use of the 9th data bit in modes 2 and 3. In the W77L32, the RI
flag is set only if the received byte corresponds to the Given or Broadcast address. This hardware
feature eliminates the software overhead required in checking every received address, and greatly
simplifies the software programmer task.
In the multiprocessor communication mode, the address bytes are distinguished from the data bytes by
transmitting the address with the 9th bit set high. When the master processor wants to transmit a block
of data to one of the slaves, it first sends out the address of the targeted slave (or slaves). All the slave
processors should have their SM2 bit set high when waiting for an address byte. This ensures that they
will be interrupted only by the reception of a address byte. The Automatic address recognition feature
ensures that only the addressed slave will be interrupted. The address comparison is done in hardware
not software.
The addressed slave clears the SM2 bit, thereby clearing the way to receive data bytes. With SM2 = 0,
the slave will be interrupted on the reception of every single complete frame of data. The unaddressed
slaves will be unaffected, as they will be still waiting for their address. In Mode 1, the 9th bit is the stop
bit, which is 1 in case of a valid frame. If SM2 is 1, then RI is set only if a valid frame is received and
the received byte matches the Given or Broadcast address.
The Master processor can selectively communicate with groups of slaves by using the Given Address.
All the slaves can be addressed together using the Broadcast Address. The addresses for each slave
are defined by the SADDR and SADEN SFRs. The slave address is an 8-bit value specified in the
SADDR SFR. The SADEN SFR is actually a mask for the byte value in SADDR. If a bit position in
SADEN is 0, then the corresponding bit position in SADDR is don't care. Only those bit positions in
SADDR whose corresponding bits in SADEN are 1 are used to obtain the Given Address. This gives
the user flexibility to address multiple slaves without changing the slave address in SADDR.
The following example shows how the user can define the Given Address to address different slaves.
Slave 1:
SADDR 1010 0100
SADEN 1111 1010
Given 1010 0x0x
- 63 -
Publication Release Date: November 2, 2001
Revision A1
Preliminary W77L32
Slave 2:
SADDR 1010 0111
SADEN 1111 1001
Given 1010 0xx1
The Given address for slave 1 and 2 differ in the LSB. For slave 1, it is a don't care, while for slave 2 it
is 1. Thus to communicate only with slave 1, the master must send an address with LSB = 0 (1010
0000). Similarly the bit 1 position is 0 for slave 1 and don't care for slave 2. Hence to communicate only
with slave 2 the master has to transmit an address with bit 1 = 1 (1010 0011). If the master wishes to
communicate with both slaves simultaneously, then the address must have bit 0 = 1 and bit 1 = 0. The
bit 3 position is don't care for both the slaves. This allows two different addresses to select both slaves
(1010 0001 and 1010 0101).
The master can communicate with all the slaves simultaneously with the Broadcast Address. This
address is formed from the logical ORing of the SADDR and SADEN SFRs. The zeros in the result are
defined as don't cares In most cases the Broadcast Address is FFh. In the previous case, the
Broadcast Address is (1111111X) for slave 1 and (11111111) for slave 2.
The SADDR and SADEN SFRs are located at address A9h and B9h respectively. On reset, these two
SFRs are initialized to 00h. This results in Given Address and Broadcast Address being set as XXXX
XXXX(i.e. all bits don't care). This effectively removes the multiprocessor communications feature,
since any selectivity is disabled.
Timed Access Protection
The W77L32 has several new features, like the Watchdog timer, on-chip ROM size adjustment, wait
state control signal and Power on/fail reset flag, which are crucial to proper operation of the system. If
left unprotected, errant code may write to the Watchdog control bits resulting in incorrect operation and
loss of control. In order to prevent this, the W77L32 has a protection scheme which controls the write
access to critical bits. This protection scheme is done using a timed access.
In this method, the bits which are to be protected have a timed write enable window. A write is
successful only if this window is active, otherwise the write will be discarded. This write enable window
is open for 3 machine cycles if certain conditions are met. After 3 machine cycles, this window
automatically closes. The window is opened by writing AAh and immediately 55h to the Timed
Access(TA) SFR. This SFR is located at address C7h. The suggested code for opening the timed
access window is
TA
REG
0C7h
MOV
TA, #0AAh
MOV
TA, #055h
; define new register TA, located at 0C7h
When the software writes AAh to the TA SFR, a counter is started. This counter waits for 3 machine
cycles looking for a write of 55h to TA. If the second write (55h) occurs within 3 machine cycles of the
first write (AAh), then the timed access window is opened. It remains open for 3 machine cycles, during
which the user may write to the protected bits. Once the window closes the procedure must be
repeated to access the other protected bits.
- 64 -
Preliminary W77L32
Examples of Timed Assessing are shown below.
Example 1: Valid access
MOV
TA, #0AAh
3 M/C
MOV
TA, #055h
3 M/C
MOV
WDCON, #00h 3 M/C
Note: M/C = Machine Cycles
Example 2: Valid access
MOV
TA, #0AAh
3 M/C
MOV
TA, #055h
3 M/C
NOP
SETB
1 M/C
EWT
2 M/C
Example 3: Invalid access
MOV
MOV
NOP
NOP
CLR
TA, #0AAh
TA, #055h
POR
3 M/C
3 M/C
1 M/C
1 M/C
2 M/C
Example 4: Invalid Access
MOV
NOP
MOV
SETB
TA, #0AAh
TA, #055h
EWT
3 M/C
1 M/C
3 M/C
2 M/C
In the first two examples, the writing to the protected bits is done before the 3 machine cycle window
closes. In Example 3, however, the writing to the protected bit occurs after the window has closed, and
so there is effectively no change in the status of the protected bit. In Example 4, the second write to TA
occurs 4 machine cycles after the first write, therefore the timed access window in not opened at all,
and the write to the protected bit fails.
13. ABSOLUTE MAXIMUM RATINGS
PARAMETER
SYMBOL
CONDITION
RATING
UNIT
VDD − VSS
-0.3
+7.0
V
Input Voltage
VIN
VSS -0.3
VDD +0.3
V
Operating Temperature
TA
0
+70
°C
Storage Temperatute
Tst
-55
+150
°C
DC Power Supply
Note: Exposure to conditions beyond those listed under Absolute Maximum Ratings may adversely affect the life and reliability
of the device.
- 65 -
Publication Release Date: November 2, 2001
Revision A1
Preliminary W77L32
14. DC ELECTRICAL CHARACTERISTICS
(TA = -40 − +85°C, Fosc = 20 MHz, unless otherwise specified.)
PARAMETER
SYMBOL
Operating Voltage
Operating Current
VDD
IDD
Idle Current
IIDLE
Power Down Current
IPWDN
Input Current
P1, P2, P3, P4
[*1]
Input Current RST
IIN1
Input Leakage Current
P0, EA
Logic 1 to 0 Transition
Current P1, P2, P3, P4
Input Low Voltage
+300
µA
ILK
-10
+10
µA
-500
-200
µA
VIL1
0
0
0.8
0.6
V
V
VDD = 5.5V
VIN = 2.0V
VDD = 4.5V
VDD = 3.0V
VIL2
0
0
0
0
2.4
2.0
0.8
0.6
0.8
0.4
VDD +0.2
VDD +0.2
V
V
V
V
V
V
VDD = 4.5V
VDD = 3.0V
VDD = 4.5V
VDD = 3.0V
VDD = 5.5V
VDD = 3.0V
3.5
2.2
3.5
2.4
-
VDD +0.2
VDD +0.2
VDD +0.2
VDD +0.2
0.45
0.40
0.45
0.40
V
V
V
V
V
V
V
V
VDD = 5.5V
VDD = 3.0V
VDD = 5.5V
VDD = 3.0V
VDD = 4.5V, IOL = +4 mA
VDD = 3V, IOL = +4 mA
VDD = 4.5V, IOL = +10 mA
VDD = 3V, IOL = +6 mA
VOH1
2.4
-
V
VOH2
2.4
-
V
VDD = 4.5V, IOH = -120 µA
VDD = 3.0V, IOH = -45 µA
VDD = 4.5V, IOH = -8 mA
VDD = 3.0V, IOH = -3 mA
[*4]
ITL
P0, P1, P2, P3, P4, EA
Input High Voltage RST
VIH2
VIL3
VIH3
VOL1
VOL2
[*2]
Output High Voltage
[*2]
P0, ALE, PSEN
No load, VDD = RST = 5.5V
No load, VDD = RST = 3.0V
No load, VDD = 5.5V
No load, VDD = 3.0V
No load, VDD = 5.5V
No load, VDD = 3.0V
VDD = 5.5V
VIN = 0V or VDD
VDD = 5.5V
0<VIN<VDD
VDD = 5.5V
0V<VIN<VDD
-10
VIH1
P0, ALE, PSEN
Output High Voltage
P1, P2, P3, P4
TEST CONDITIONS
IIN2
P0, P1, P2, P3, P4, EA
Input Low Voltage
[*1]
RST
Input Low Voltage
[*3]
XTAL1
Input High Voltage
Input High Voltage
[*3]
XTAL1
Output Low Voltage
P1, P2, P3, P4
Output Low Voltage
SPECIFICATION
MIN.
MAX.
UNIT
2.7
5.5
V
50
mA
15
mA
30
mA
12
mA
10
µA
10
µA
-70
+10
µA
Notes:
*1. RST pin is a Schmitt trigger input.
*2. P0, ALE and PSEN are tested in the external access mode.
*3. XTAL1 is a CMOS input.
*4. Pins of P1, P2, P3 can source a transition current when they are being externally driven from 1 to 0. The transition
current reaches its maximum value when VIN approximates to 2V.
- 66 -
Preliminary W77L32
15. AC CHARACTERISTICS
tCLCL
tCLCH
tCLCX
tCHCL
tCHCX
External Clock Characteristics
PARAMETER
SYMBOL
MIN.
TYP.
MAX.
UNITS
Clock High Time
tCHCX
12.5
-
-
nS
Clock Low Time
tCLCX
12.5
-
-
nS
Clock Rise Time
tCLCH
-
-
10
nS
Clock Fall Time
tCHCL
-
-
10
nS
NOTES
Note: Duty cycle is 50 %.
AC Specification
PARAMETER
Oscillator Frequency
ALE Pulse Width
SYM.
1/tCLCL
VARIABLE
CLOCK
MIN.
0
tLHLL
1.5 tCLCL - 5
VARIABLE
CLOCK
MAX.
40
UNITS
MHz
nS
Address Valid to ALE Low
tAVLL
0.5 tCLCL - 5
nS
Address Hold After ALE Low
tLLAX1
0.5 tCLCL - 5
nS
Address Hold After ALE Low for MOVX Write
tLLAX2
0.5 tCLCL - 5
nS
ALE Low to Valid Instruction In
tLLIV
ALE Low to PSEN Low
tLLPL
0.5 tCLCL - 5
nS
PSEN Pulse Width
tPLPH
2.0 tCLCL - 5
nS
PSEN Low to Valid Instruction In
Input Instruction Hold After PSEN
tPLIV
tPXIX
Input Instruction Float After PSEN
tPXIZ
tCLCL - 5
nS
Port 0 Address to Valid Instr. In
tAVIV1
3.0 tCLCL - 20
nS
Port 2 Address to Valid Instr. In
tAVIV2
3.5 tCLCL - 20
nS
PSEN Low to Address Float
Data Hold After Read
tPLAZ
0
nS
tRHDX
0
nS
Data Float After Read
tRHDZ
tCLCL - 5
nS
RD Low to Address Float
tRLAZ
0.5 tCLCL - 5
nS
- 67 -
2.5 tCLCL - 20
2.0 tCLCL - 20
0
nS
nS
nS
Publication Release Date: November 2, 2001
Revision A1
Preliminary W77L32
MOVX Characteristics Using Strech Memory Cycles
PARAMETER
Data Access ALE Pulse Width
SYM.
VARIABLE
CLOCK
MIN.
tLLHL2
1.5 tCLCL - 5
VARIABLE
CLOCK
MAX.
UNITS
STRECH
nS
tMCS = 0
2.0 tCLCL - 5
tMCS > 0
Address Hold After ALE Low for
MOVX Write
tLLAX2
0.5 tCLCL - 5
nS
RD Pulse Width
tRLRH
2.0 tCLCL - 5
nS
tMCS - 10
WR Pulse Width
tWLWH
tMCS > 0
2.0 tCLCL - 5
nS
tMCS - 10
RD Low to Valid Data In
nS
tMCS - 20
Data Hold after Read
tRHDX
Data Float after Read
tRHDZ
0
nS
tCLCL - 5
2.5 tCLCL - 5
tLLDV
nS
3.0 tCLCL - 20
tAVDV1
nS
3.5 tCLCL - 20
tAVDV2
nS
Port 0 Address to RD or WR Low
tLLWL
tAVWL
0.5 tCLCL - 5
0.5 tCLCL + 5
1.5 tCLCL - 5
1.5 tCLCL + 5
tCLCL - 5
nS
tAVWL2
nS
nS
nS
tWHQX
-5
nS
tRLAZ
RD or WR High to ALE High
tWHLH
tMCS = 0
tMCS > 0
tCLCL - 5
nS
2.0 tCLCL - 5
RD Low to Address Float
tMCS = 0
tMCS > 0
1.0 tCLCL - 5
Data Hold after Write
tMCS = 0
tMCS > 0
1.5 tCLCL - 5
tQVWX
tMCS = 0
tMCS > 0
2.5 tCLCL - 5
Data Valid to WR Transition
tMCS = 0
tMCS > 0
2.0 tCLCL - 5
Port 2 Address to RD or WR Low
tMCS = 0
tMCS > 0
2.5 tCLCL - 5
ALE Low to RD or WR Low
tMCS = 0
tMCS > 0
2.0tCLCL - 5
Port 2 Address to Valid Data In
tMCS = 0
tMCS > 0
tMCS + 2tCLCL - 40
Port 0 Address to Valid Data In
tMCS = 0
tMCS > 0
2.0 tCLCL - 5
ALE Low to Valid Data In
tMCS = 0
tMCS > 0
2.0 tCLCL - 20
tRLDV
tMCS = 0
tMCS = 0
tMCS > 0
0.5 tCLCL - 5
nS
0
10
nS
1.0 tCLCL - 5
1.0 tCLCL + 5
tMCS = 0
tMCS > 0
Note: tMCS is a time period related to the Stretch memory cycle selection. The following table shows the time period of tMCS for
each selection of the Stretch value.
- 68 -
Preliminary W77L32
M2
0
0
0
0
1
1
1
1
M1
0
0
1
1
0
0
1
1
M0
0
1
0
1
0
1
0
1
MOVX Cycles
2 machine cycles
3 machine cycles
4 machine cycles
5 machine cycles
6 machine cycles
7 machine cycles
8 machine cycles
9 machine cycles
tMCS
0
4 tCLCL
8 tCLCL
12 tCLCL
16 tCLCL
20 tCLCL
24 tCLCL
28 tCLCL
Explanation of Logic Symbols
In order to maintain compatibility with the original 8051 family, this device specifies the same
parameter for each device, using the same symbols. The explanation of the symbols is as follows.
t
C
H
Time
Clock
Logic level high
A
D
L
Address
Input Data
Logic level low
I
Instruction
P
PSEN
Q
Output Data
R
RD signal
V
X
Valid
No longer a valid state
W
Z
WR signal
Tri-state
15. TIMING WAVEFORMS
Program Memory Read Cycle
tLHLL
tLLIV
ALE
tAVLL
tPLPH
tPLIV
PSEN
tLLPL
tPXIZ
tPLAZ
tLLAX1
PORT 0
ADDRESS
A0-A7
tPXIX
INSTRUCTION
IN
ADDRESS
A0-A7
tAVIV1
tAVIV2
PORT 2
ADDRESS A8-A15
- 69 -
ADDRESS A8-A15
Publication Release Date: November 2, 2001
Revision A1
Preliminary W77L32
Timing Waveforms, continued
Data Memory Read Cycle
tLLDV
ALE
tWHLH
tLLWL
PSEN
tRLRH
tLLAX1
tRLDV
tAVLL
RD
tAVWL1
PORT 0 INSTRUCTION
IN
tRHDZ
tRLAZ
tRHDX
ADDRESS
A0-A7
DATA
IN
ADDRESS
A0-A7
tAVDV1
tAVDV2
ADDRESS A8-A15
PORT 2
Data Memory Write Cycle
ALE
tWHLH
tLLWL
PSEN
tWLWH
tLLAX2
tAVLL
WR
tAVWL1
tWHQX
tQVWX
PORT 0
INSTRUCTION
IN
ADDRESS
A0-A7
DATA OUT
tAVDV2
PORT 2
ADDRESS A8-A15
- 70 -
ADDRESS
A0-A7
Preliminary W77L32
16. TYPICAL APPLICATION CIRCUITS
Expanded External Program Memory and Crystal
VCC
31
19
10 u
R
EA
XTAL1
18
XTAL2
9
RST
CRYSTAL
8.2 K
C1
C2
INT0
12
13
14
15
INT1
T0
T1
1
2
3
4
5
6
7
8
P1.0
P1.1
P1.2
P1.3
P1.4
P1.5
P1.6
P1.7
P0.0
P0.1
P0.2
P0.3
P0.4
P0.5
P0.6
P0.7
39
38
37
36
35
34
33
32
P2.0
P2.1
P2.2
P2.3
P2.4
P2.5
P2.6
P2.7
21
22
23
24
25
26
27
28
RD
WR
PSEN
ALE
TXD
RXD
17
16
29
30
11
10
AD0
AD1
AD2
AD3
AD4
AD5
AD6
AD7
AD0
AD1
AD2
AD3
AD4
AD5
AD6
AD7
A8
A9
A10
A11
A12
A13
A14
A15
GND
3
4
7
8
13
14
17
18
1
11
D0
D1
D2
D3
D4
D5
D6
D7
Q0
Q1
Q2
Q3
Q4
Q5
Q6
Q7
2
5
6
9
12
15
16
19
A0 10
A1
9
A2
8
A3
7
A4
6
A5
5
A6
4
A7
3
A8 25
A9 24
A10 21
A11 23
A12 2
A13 26
A14 27
A15 1
A0
A1
A2
A3
A4
A5
A6
A7
OC
G
74F373
GND
20
22
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
O0
O1
O2
O3
O4
O5
O6
O7
11
12
13
15
16
17
18
19
AD0
AD1
AD2
AD3
AD4
AD5
AD6
AD7
CE
OE
27512
W77L32
Figure A
CRYSTAL
C1
C2
R
16 MHz
30P
30P
-
25 MHz
15P
15P
-
The above table shows the reference values for crystal applications.
Note: C1, C2, R components refer to Figure A.
- 71 -
Publication Release Date: November 2, 2001
Revision A1
Preliminary W77L32
Typical Application Circuits, continued
Expanded External Data Memory and Oscillator
VCC
31
10 u
EA
19
XTAL1
18
XTAL2
9
RST
12
13
14
15
INT0
OSCILLATOR
8.2 K
1
2
3
4
5
6
7
8
INT1
T0
T1
P1.0
P1.1
P1.2
P1.3
P1.4
P1.5
P1.6
P1.7
P0.0
P0.1
P0.2
P0.3
P0.4
P0.5
P0.6
P0.7
39
38
37
36
35
34
33
32
AD0
AD1
AD2
AD3
AD4
AD5
AD6
AD7
AD0
AD1
AD2
AD3
AD4
AD5
AD6
AD7
P2.0
P2.1
P2.2
P2.3
P2.4
P2.5
P2.6
P2.7
21
22
23
24
25
26
27
28
A8
A9
A10
A11
A12
A13
A14
GND 1
11
RD
17
16
29
30
11
10
WR
PSEN
ALE
TXD
RXD
3
4
7
8
13
14
17
18
D0
D1
D2
D3
D4
D5
D6
D7
Q0
Q1
Q2
Q3
Q4
Q5
Q6
Q7
2
5
6
9
12
15
16
19
A0
A1
A2
A3
A4
A5
A6
A7
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
OC
G
74F373
10
9
8
7
6
5
4
3
25
24
21
23
2
26
1
GND 20
22
27
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
CE
OE
D0
D1
D2
D3
D4
D5
D6
D7
11
12
13
15
16
17
18
19
AD0
AD1
AD2
AD3
AD4
AD5
AD6
AD7
WR
20256
W77L32
Figure B
17. PACKAGE DIMENSIONS
40-pin DIP
Symbol
A
A1
A2
B
B1
c
D
E
E1
e1
L
D
40
21
E1
a
eA
S
20
1
c
A A2
A1
L
Base Plane
Seating Plane
B
B
e1
a
1
- 72 -
eA
Min.
Nom.
Dimension in mm
Max.
Min.
Nom.
Max.
5.334
0.210
0.010
0.254
0.150
0.155
0.160
3.81
3.937
4.064
0.016
0.018
0.022
0.406
0.457
0.559
0.048
0.050
0.054
1.219
1.27
0.008
0.010
0.014
0.203
2.055
2.070
1.372
0.254
0.356
52.20
52.58
15.494
0.590
0.600
0.610
14.986
15.24
0.540
0.545
0.550
13.72
13.84
13.97
0.090
0.100
0.110
2.286
2.54
2.794
0.130
0.140
3.048
3.302
3.556
0.650
0.670
16.51
17.01
0.120
0
0.630
15
0
16.00
0.090
Notes:
E
S
Dimension in inches
1. Dimension D Max. & S include mold flash or
tie bar burrs.
2. Dimension E1 does not include interlead flash.
3. Dimension D & E1 include mold mismatch and
.
are determined at the mold parting
line.
4. Dimension B1 does not include dambar
protrusion/intrusion.
5. Controlling dimension: Inches.
6. General appearance spec. should be based on
final visual inspection spec.
15
2.286
Preliminary W77L32
Package Dimensions, continued
44-pin PLCC
HD
D
6
1
44
40
Symbol
7
39
E
17
HE
GE
29
18
28
c
A
A1
A2
b1
b
c
D
E
e
GD
GE
HD
HE
L
y
Dimension in inches
Dimension in mm
Min. Nom. Max.
Min. Nom. Max.
0.185
4.699
0.508
0.020
0.145 0.150
0.155
3.683
3.81
3.937
0.026 0.028
0.032
0.66
0.711
0.813
0.016 0.018
0.022
0.406 0.457
0.559
0.008 0.010
0.014
0.203
0.254
0.356
0.648 0.653
0.658 16.46 16.59
16.71
0.648 0.653
0.658 16.46 16.59
16.71
0.050
1.27
BSC
BSC
0.590 0.610
0.630 14.99 15.49
16.00
0.590 0.610
0.630 14.99 15.49
16.00
0.680 0.690
0.700 17.27
17.53 17.78
0.680 0.690
0.700 17.27
17.53 17.78
0.090 0.100
0.110
2.296
2.54
2.794
0.10
0.004
L
Notes:
A2 A
1. Dimension D & E do not include interlead
flash.
2. Dimension b1 does not include dambar
protrusion/intrusion.
3. Controlling dimension: Inches
4. General appearance spec. should be based
on final visual inspection spec.
θ
e
b
b1
Seating Plane
A1
y
GD
44-pin QFP
HD
Dimension in Inches
D
Symbol
E HE
11
12
Nom.
Max.
Min.
Nom.
---
---
---
---
---
0.002
0.01
0.02
0.05
0.25
0.5
0.075
0.081
0.087
1.90
2.05
2.20
0.01
0.014
0.018
0.25
0.35
0.45
c
D
E
e
0.004
0.006
0.010
0.101
0.152
0.254
0.390
0.394
0.398
9.9
10.00
10.1
0.390
0.394
0.398
9.9
10.00
10.1
0.025
0.031
0.036
0.635
0.80
0.952
HD
HE
L
L1
y
0.510
0.520
0.530
12.95
13.2
13.45
13.45
A
A1
A2
b
33
1
e
b
θ
22
Dimension in mm
Min.
34
44
Max.
---
0.510
0.520
0.530
12.95
13.2
0.025
0.031
0.037
0.65
0.8
0.95
0.051
0.063
0.075
1.295
1.6
1.905
0.08
0.003
0
7
0
7
Notes:
1. Dimension D & E do not include interlead
flash.
2. Dimension b does not include dambar
protrusion/intrusion.
3. Controlling dimension: Millimeter
4. General appearance spec. should be based
on final visual inspection spec.
c
A2
A
θ
A1
Seating Plane
See Detail F
y
L
L
Detail F
1
- 73 -
Publication Release Date: November 2, 2001
Revision A1
Preliminary W77L32
Headquarters
Winbond Electronics Corporation America
Winbond Electronics (Shanghai) Ltd.
No. 4, Creation Rd. III,
Science-Based Industrial Park,
Hsinchu, Taiwan
TEL: 886-3-5770066
FAX: 886-3-5665577
http://www.winbond.com.tw/
2727 North First Street, San Jose,
CA 95134, U.S.A.
TEL: 1-408-9436666
FAX: 1-408-5441798
27F, 2299 Yan An W. Rd. Shanghai,
200336 China
TEL: 86-21-62365999
FAX: 86-21-62365998
Taipei Office
Winbond Electronics Corporation Japan
Winbond Electronics (H.K.) Ltd.
11F, No. 115, Sec. 3,
Min-Sheng East. Rd.,
Taipei, Taiwan
TEL: 886-2-27190505
FAX: 886-2-27197502
7F Daini-ueno BLDG, 3-7-18
Shinyokohama Kohoku-ku,
Yokohama, 222-0033
TEL: 81-45-4781881
FAX: 81-45-4781800
Unit 9-15, 22F, Millennium City,
No. 378 Kwun Tong Rd.,
Kowloon, Hong Kong
TEL: 852-27513100
FAX: 852-27552064
Please note that all data and specifications are subject to change without notice.
All the trade marks of products and companies mentioned in this data sheet belong to their respective owners.
- 74 -