WINBOND W79E823

W79E825A/824A/823B/822B Data Sheet
8-BIT MICROCONTROLLER
Table of Contents1
2
3
4
5
6
GENERAL DESCRIPTION ......................................................................................................... 4
FEATURES ................................................................................................................................. 5
PARTS INFORMATION LIST ..................................................................................................... 6
3.1
Lead Free (RoHS) Parts information list......................................................................... 6
PIN CONFIGURATION ............................................................................................................... 7
PIN DESCRIPTION..................................................................................................................... 8
FUNCTIONAL DESCRIPTION.................................................................................................... 9
6.1
On-Chip Flash EPROM .................................................................................................. 9
6.2
I/O Ports.......................................................................................................................... 9
6.3
Serial I/O ......................................................................................................................... 9
6.4
Timers ............................................................................................................................. 9
6.5
Interrupts......................................................................................................................... 9
6.6
Data Pointers .................................................................................................................. 9
6.7
Architecture................................................................................................................... 10
6.7.1
6.7.2
6.7.3
6.7.4
6.7.5
6.7.6
7
8
9
10
11
ALU ................................................................................................................................10
Accumulator ...................................................................................................................10
B Register.......................................................................................................................10
Program Status Word: ....................................................................................................10
Scratch-pad RAM ...........................................................................................................10
Stack Pointer ..................................................................................................................11
6.8
Power Management...................................................................................................... 11
MEMORY ORGANIZATION...................................................................................................... 12
7.1
Program Memory (on-chip Flash) ................................................................................. 12
7.2
Data Memory ................................................................................................................ 12
7.3
Register Map................................................................................................................. 13
7.4
Working Registers......................................................................................................... 16
7.5
Bit addressable Locations............................................................................................. 16
7.6
Stack ............................................................................................................................. 16
SPECIAL FUNCTION REGISTERS ......................................................................................... 17
INSTRUCTION SET.................................................................................................................. 48
9.1
Instruction Timing.......................................................................................................... 56
POWER MANAGEMENT.......................................................................................................... 59
10.1 Idle Mode ...................................................................................................................... 59
10.2 Power Down Mode ....................................................................................................... 59
RESET CONDITIONS............................................................................................................... 60
11.1 Sources of reset............................................................................................................ 60
11.1.1
External Reset ..............................................................................................................60
-1-
Publication Release Date: February 21, 2008
Revision A9
W79E825A/824A/823B/822B Data Sheet
11.1.2
11.1.3
12
13
11.2 Reset State ................................................................................................................... 60
INTERRUPTS ........................................................................................................................... 65
12.1 Interrupt Sources .......................................................................................................... 65
12.2 Priority Level Structure ................................................................................................. 67
12.3 Response Time............................................................................................................. 68
12.4 Interrupt Inputs.............................................................................................................. 69
PROGRAMMABLE TIMERS/COUNTERS ............................................................................... 71
13.1 Timer/Counters 0 & 1.................................................................................................... 71
13.1.1
13.1.2
13.1.3
13.1.4
13.1.5
14
15
16
17
18
19
20
21
22
23
Power-On Reset (POR)................................................................................................60
Watchdog Timer Reset.................................................................................................60
Time-Base Selection ....................................................................................................71
Mode 0 .........................................................................................................................71
Mode 1 .........................................................................................................................72
Mode 2 .........................................................................................................................73
Mode 3 .........................................................................................................................73
NVM MEMORY ......................................................................................................................... 75
WATCHDOG TIMER................................................................................................................. 77
15.1 WATCHDOG CONTROL.............................................................................................. 78
15.2 CLOCK CONTROL of Watchdog.................................................................................. 79
SERIAL PORT (UART) ............................................................................................................. 80
16.1 MODE 0 ........................................................................................................................ 80
16.2 MODE 1 ........................................................................................................................ 81
16.3 MODE 2 ........................................................................................................................ 83
16.4 MODE 3 ........................................................................................................................ 84
16.5 Framing Error Detection ............................................................................................... 85
16.6 Multiprocessor Communications................................................................................... 85
TIME ACCESS PROCTECTION .............................................................................................. 87
KEYBOARD INTERRUPT (KBI) ............................................................................................... 89
ANALOG COMPARATORS ...................................................................................................... 90
I/O PORT CONFIGURATION ................................................................................................... 91
20.1 Quasi-Bidirectional Output Configuration ..................................................................... 91
20.2 Open Drain Output Configuration ................................................................................. 92
20.3 Push-Pull Output Configuration .................................................................................... 93
20.4 Input Only Configuration ............................................................................................... 93
OSCILLATOR ........................................................................................................................... 94
21.1 On-Chip RC Oscillator Option....................................................................................... 94
21.2 External Clock Input Option .......................................................................................... 95
21.3 CPU Clock Rate select ................................................................................................. 95
POWER MONITORING FUNCTION ........................................................................................ 96
22.1 Power On Detect........................................................................................................... 96
22.2 Brownout Detect ........................................................................................................... 96
PULSE-WIDTH-MODULATED (PWM) OUTPUTS ................................................................... 97
-2-
W79E825A/824A/823B/822B Data Sheet
24
25
ANALOG-TO-DIGITAL CONVERTER .................................................................................... 101
24.1 ADC Resolution and Analog Supply: .......................................................................... 102
I2C SERIAL CONTROL .......................................................................................................... 104
25.1 SIO Port ...................................................................................................................... 104
25.2 The I2C Control Registers: ......................................................................................... 105
25.2.1
25.2.2
25.2.3
25.2.4
25.2.5
25.3
Modes of Operation .................................................................................................... 107
25.3.1
25.3.2
25.3.3
25.3.4
26
27
28
29
30
The Address Registers, I2ADDR ................................................................................105
The Data Register, I2DAT ..........................................................................................105
The Control Register, I2CON .....................................................................................106
The Status Register, I2STATUS.................................................................................106
The I2C Clock Baud Rate Bits, I2CLK ........................................................................106
Master Transmitter Mode ...........................................................................................107
Master Receiver Mode ...............................................................................................107
Slave Receiver Mode .................................................................................................107
Slave Transmitter Mode .............................................................................................108
25.4 Data Transfer Flow in Five Operating Modes............................................................. 108
ICP(IN-CIRCUIT PROGRAM) FLASH PROGRAM ................................................................ 114
CONFIG BITS ......................................................................................................................... 115
27.1 CONFIG1 .................................................................................................................... 115
27.2 CONFIG2 .................................................................................................................... 116
ELECTRICAL CHARACTERISTICS....................................................................................... 118
28.1 Absolute Maximum Ratings ........................................................................................ 118
28.2 DC ELECTRICAL CHARACTERISTICS .................................................................... 119
28.3 The ADC Converter DC ELECTRICAL CHARACTERISTICS ................................... 121
28.4 The COMPARATOR ELECTRICAL CHARACTERISTICS ........................................ 121
28.5 AC ELECTRICAL CHARACTERISTICS .................................................................... 121
28.6 EXTERNAL CLOCK CHARACTERISTICS ................................................................ 122
28.7 AC SPECIFICATION .................................................................................................. 122
28.8 TYPICAL APPLICATION CIRCUITS .......................................................................... 122
PACKAGE DIMENSIONS ....................................................................................................... 123
29.1 20-pin SOP ................................................................................................................. 123
29.2 20-pin DIP ................................................................................................................... 124
REVISION HISTORY .............................................................................................................. 125
-3-
Publication Release Date: February 21, 2008
Revision A9
W79E825A/824A/823B/822B Data Sheet
1
GENERAL DESCRIPTION
The W79E825 series are an 8-bit Turbo 51 microcontroller which has an in-system programmable
Flash EPROM which Flash EPROM can program by ICP (In Circuit Program) or by hardware writer.
The instruction set of the W79E825 series are fully compatible with the standard 8052. The W79E825
series contain a 16K/8K/4K/2K bytes of main Flash EPROM; a 256/128 bytes of RAM; 256/128 bytes
NVM Data Flash EPROM; two 8-bit bi-directional, one 2-bit bi-directional and bit-addressable I/O
ports; two 16-bit timer/counters; 4-channel multiplexed 10-bit A/D convert; 4-channel 10-bit PWM; two
serial ports that include a I2C and an enhanced full duplex serial port. These peripherals are
supported by 13 sources four-level interrupt capability. To facilitate programming and verification, the
Flash EPROM inside the W79E825 series allow the program memory to be programmed and read
electronically. Once the code is confirmed, the user can protect the code for security.
-4-
W79E825A/824A/823B/822B Data Sheet
2
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
FEATURES
Fully static design 8-bit Turbo 51 CMOS microcontroller up to 20MHz when VDD=4.5V to 5.5V,
12MHz when VDD=2.7V to 5.5V
16K/8K/4K/2K bytes of AP Flash EPROM, with ICP and external writer programmable mode.
256/128 bytes of on-chip RAM.
256/128 bytes NVM Data Flash EPROM for customer data storage used and 10K writer cycles.
Instruction-set compatible with MSC-51.
Two 8-bit bi-directional and one 2-bit bi-directional ports.
Two 16-bit timer/counters.
13 interrupts source with four levels of priority.
One enhanced full duplex serial port with framing error detection and automatic address
recognition.
The 4 outputs mode and TTL/Schmitt trigger selectable Port.
Programmable Watchdog Timer.
Four-channel 10-bit PWM (Pulse Width Modulator).
Four-channel multiplexed with 10-bits A/D convert.
One I2C communication port (Master / Slave).
Eight keypad interrupt inputs.
Two analog comparators.
Configurable on-chip oscillator.
LED drive capability (20mA) on all port pins.
Low Voltage Detect interrupt and reset.
Development Tools:
- JTAG ICE(In Circuit Emulation) tool
- ICP(In Circuit Programming) writer
Packages:
- Lead Free (RoHS) DIP 20:
W79E825ADG
- Lead Free (RoHS) DIP 20:
W79E825ADG
- Lead Free (RoHS) SOP 20:
W79E825ASG
- Lead Free (RoHS) DIP 20:
W79E824ADG
- Lead Free (RoHS) SOP 20:
W79E824ASG
- Lead Free (RoHS) DIP 20:
W79E823BDG
- Lead Free (RoHS) SOP 20:
W79E823BSG
- Lead Free (RoHS) DIP 20:
W79E822BDG
- Lead Free (RoHS) SOP 20:
W79E822BSG
-5-
Publication Release Date: February 21, 2008
Revision A9
W79E825A/824A/823B/822B Data Sheet
3 PARTS INFORMATION LIST
3.1 Lead Free (RoHS) Parts information list
PART NO.
EPROM FLASH
SIZE
RAM
NVM FLASH
EPROM
PACKAGE
W79E825ADG
16KB
256B
256B
DIP-20 Pin
W79E825ASG
16KB
256B
256B
SOP-20 Pin
W79E824ADG
8KB
256B
256B
DIP-20 Pin
W79E824ASG
8KB
256B
256B
SOP-20 Pin
W79E823BDG
4KB
128B
128B
DIP-20 Pin
W79E823BSG
4KB
128B
128B
SOP-20 Pin
W79E822BDG
2KB
128B
128B
DIP-20 Pin
W79E822BSG
2KB
128B
128B
SOP-20 Pin
Table 3-1: Lead Free (RoHS) Parts information list
-6-
REMARK
W79E825A/824A/823B/822B Data Sheet
4
PIN CONFIGURATION
20 PIN DIP
1
20 P0.1/CIN2B/PWM0
PWM2/P1.7
2
19 P0.2/CIN2A/BRAKE
PWM1/P1.6
3
18 P0.3/CIN1B/AD0
RST/P1.5
4
17 P0.4/CIN1A/AD1
VSS
5
16 P0.5/CMPREF/AD2
PWM3/CMP2/P0.0
XTAL1/P2.1
6
15 VDD
XTAL2/CLKOUT/P2.0
7
14 P0.6/CMP1/AD3
INT1/P1.4
8
13 P0.7/T1
SDA/INT0/P1.3
9
12 P1.0/TXD
SCL/T0/P1.2 10
11 P1.1/RXD
20 PIN SOP
PWM3/CMP2/P0.0
1
20 P0.1/CIN2B/PWM0
PWM2/P1.7
2
19 P0.2/CIN2A/BRAKE
PWM1/P1.6
3
18 P0.3/CIN1B/AD0
RST/P1.5
4
17 P0.4/CIN1A/AD1
VSS
5
16 P0.5/CMPREF/AD2
XTAL1/P2.1
6
15 VDD
XTAL2/CLKOUT/P2.0
7
14 P0.6/CMP1/AD3
INT1/P1.4
8
13 P0.7/T1
SDA/INT0/P1.3
9
12 P1.0/TXD
SCL/T0/P1.2 10
11 P1.1/RXD
Figure 4-1: Pin Configuration
-7-
Publication Release Date: February 21, 2008
Revision A9
W79E825A/824A/823B/822B Data Sheet
5
PIN DESCRIPTION
SYMBOL
TYPE
DESCRIPTIONS
RESET: A low on this pin for two machine cycles while the oscillator is
running resets the device.
RST (P1.5)
I
XTAL1(P2.1)
I/O
CRYSTAL1: This is the crystal oscillator input. This pin may be driven by
an external clock or configurable I/O pin.
XTAL2(P2.0)
I/O
CRYSTAL2: This is the crystal oscillator output. It is the inversion of
XTAL1 or configurable I/O pin.
VSS
P
GROUND: Ground potential
VDD
P
POWER: SUPPLY: Supply voltage for operation.
P0.0−P0.7
I/O
PORT 0: Port 0 is four mode output pin and two mode input. The
P0.3~P0.6 are 4-channel input ports (ADC0-ADC3) for ADC used.
P1.0−P1.7
I/O
PORT 1: Port 1 is four mode output pin and two mode input. The P1.2
(SCL) and P1.3 (SDA) is only open drain circuit, and P1.5 only input pin.
* TYPE: P: power, I: input, O: output, I/O: bi-directional, H: pull-high, L: pull-low, D: open-drain.
Table 5-1: Pin Description
-8-
W79E825A/824A/823B/822B Data Sheet
6
FUNCTIONAL DESCRIPTION
The W79E825 series architecture consist of a 4T 8051 core controller surrounded by various registers,
16K/8K/4K/2K bytes Flash EPROM, 256/128 bytes of RAM, 256/128 bytes NVM Data Flash EPROM,
three general purpose I/O ports, two timer/counters, one serial port, one I2C serial I/O, 4 channel
PWM with 10-bit counter, 4-channel multiplexed with 10-bit ADC analog input, Flash EPROM program
by Writer and ICP.
6.1
On-Chip Flash EPROM
The W79E825 series include one 16K/8K/4K/2K bytes of main Flash EPROM for application program.
A Writer or ICP programming board is required to program the Flash EPROM or NVM Data Flash
EPROM.
This ICP (In-Circuit Programming) feature makes the job easy and efficient when the application’s
firmware needs to be updated frequently. In some applications, the in-circuit programming feature
makes it possible for the end-user to easily update the system firmware without opening the chassis.
6.2
I/O Ports
The W79E825 series have two 8-bit and one 2-bit port, up to 18 I/O pins using on-chip oscillator &
/RST is input only by reset options. All ports can be used as four outputs mode when it may set by
PxM1.y and PxM2.y SFR’s registers, it has strong pull-ups and pull-downs, and does not need any
external pull-ups. Otherwise it can be used as general I/O port as open drain circuit. All ports can be
used bi-directional and these are as I/O ports. These ports are not true I/O, but rather are pseudo-I/O
ports. This is because these ports have strong pull-downs and weak pull-ups.
6.3
Serial I/O
The W79E825 series have one serial port that is functionally similar to the serial port of the original
8032 family. However the serial port on the W79E825 series can operate in different modes in order to
obtain timing similarity as well. The Serial port has the enhanced features of Automatic Address
recognition and Frame Error detection.
6.4
Timers
The W79E825 series have two 16-bit timers that are functionally and similar to the timers of the 8052
family. When used as timers, the user has a choice of 12 or 4 clocks per count that emulates the
timing of the original 8052.
6.5
Interrupts
The Interrupt structure in the W79E825 series is slightly different from that of the standard 8052. Due
to the presence of additional features and peripherals, the number of interrupt sources and vectors
has been increased.
6.6
Data Pointers
The data pointers of W79E825 series are same as 8052 that has dual 16-bit Data Pointers (DPTR) by
setting DPS bit at AUXR1.0. The figure of dual DPTR is as below diagram.
-9-
Publication Release Date: February 21, 2008
Revision A9
W79E825A/824A/823B/822B Data Sheet
AUXR1.0
DPS=0
DPTR
DPS=1
DPTR1
DPS
Figure 6-1: Dual DPTR
6.7
Architecture
The W79E825 series are based on the standard 8052 device. It is built around an 8-bit ALU that uses
internal registers for temporary storage and control of the peripheral devices. It can execute the
standard 8052 instruction set.
6.7.1 ALU
The ALU is the heart of the W79E825 series. It is responsible for the arithmetic and logical functions. It
is also used in decision making, in case of jump instructions, and is also used in calculating jump
addresses. The user cannot directly use the ALU, but the Instruction Decoder reads the op-code,
decodes it, and sequences the data through the ALU and its associated registers to generate the
required result. The ALU mainly uses the ACC which is a special function register (SFR) on the chip.
Another SFR, namely B register is also used in Multiply and Divide instructions. The ALU generates
several status signals which are stored in the Program Status Word register (PSW).
6.7.2 Accumulator
The Accumulator (ACC) is the primary register used in arithmetic, logical and data transfer operations
in the W79E825 series. Since the Accumulator is directly accessible by the CPU, most of the high
speed instructions make use of the ACC as one argument.
6.7.3 B Register
This is an 8-bit register that is used as the second argument in the MUL and DIV instructions. For all
other instructions it can be used simply as a general purpose register.
6.7.4 Program Status Word:
This is an 8-bit SFR that is used to store the status bits of the ALU. It holds the Carry flag, the Auxiliary
Carry flag, General purpose flags, the Register Bank Select, the Overflow flag, and the Parity flag.
6.7.5 Scratch-pad RAM
The W79E825 series have a 256/128 bytes on-chip scratch-pad RAM. These can be used by the user
for temporary storage during program execution. A certain section of this RAM is bit addressable, and
can be directly addressed for this purpose.
- 10 -
W79E825A/824A/823B/822B Data Sheet
6.7.6 Stack Pointer
The W79E825 series have an 8-bit Stack Pointer which points to the top of the Stack. This stack
resides in the Scratch Pad RAM in the W79E825 series. Hence the size of the stack is limited by the
size of this RAM.
6.8
Power Management
Power Management like the standard 8052, the W79E825 series also have the IDLE and POWER
DOWN modes of operation. In the IDLE mode, the clock to the CPU is stopped while the timers, serial
ports and interrupt lock continue to operate. In the POWER DOWN mode, all clocks are stopped and
the chip operation is completely stopped. This is the lowest power consumption state.
- 11 -
Publication Release Date: February 21, 2008
Revision A9
W79E825A/824A/823B/822B Data Sheet
7
MEMORY ORGANIZATION
The W79E825 series separate the memory into two separate sections, the Program Memory and the
Data Memory. The Program Memory is used to store the instruction op-codes, while the Data Memory
is used to store data or for memory mapped devices.
7.1
Program Memory (on-chip Flash)
The Program Memory on the W79E825 series can be up to 16K/8K/4K/2K bytes long. All instructions
are fetched for execution from this memory area. The MOVC instruction can also access this memory
region.
7.2
Data Memory
The NVM Data Memory of Flash EPROM on the W79E825 series can be up to 256/128 bytes long.
The W79E825 series read the content of data memory by using “MOVC A, @A+DPTR”. To write data
is by NVMADDR, NVMDAT and NVMCON SFR’s registers.
FFFFH
Page 3
64 bytes
Unused
Code M emory
FCFFH
FC00H
FBFFH
Page 2
64 bytes
256 Bytes
NVM
Data Mem ory
Page 1
64 bytes
Page 0
64 bytes
Unused
Code M emory
FCC0H
FCBFH
FC80H
FC7FH
FC40H
FC3FH
FC00H
NVM Data M em ory Area
4000H/2000H
3FFFH/1FFFH
16K/8K Bytes
On-Chip
Code M emory
CONFIG 2
CONFIG 1
0000H
O n-Chip Code M em ory Space
Figure 7-1: W79E825/824 Memory Map
- 12 -
FCFFH
W79E825A/824A/823B/822B Data Sheet
FFFFH
U nused
C o d e M e m o ry
FC 7FH
FC00H
Page 1
6 4 b y te s
1 2 8 B y te s
NVM
D a ta M e m o ry
U nused
C o d e M e m o ry
Page 0
6 4 b y te s
FC 7FH
FC 40H
FC 3FH
FC 00H
N V M D a ta M e m o ry a re a
1 0 0 0 H /0 8 0 0 H
0 F F F H /0 7 F F H
4 K /2 K B y te s
O n -C h ip
C o d e M e m o ry
C O N F IG 2
C O N F IG 1
0000H
O n -C h ip C o d e M e m o ry S p a c e
Figure 7-2: W79E823/822 Memory Map
7.3
Register Map
As mentioned before the W79E825 series have separate Program and Data Memory areas. The onchip 256/128 bytes scratch pad RAM is in addition to the external memory. There are also several
Special Function Registers (SFRs) which can be accessed by software. The SFRs can be accessed
only by direct addressing, while the on-chip RAM can be accessed by either direct or indirect
addressing.
- 13 -
Publication Release Date: February 21, 2008
Revision A9
W79E825A/824A/823B/822B Data Sheet
FFH
SFR
Direct
Addressing
Only
Indirect
RAM
Addressing
80H
7FH
Direct
&
Indirect
RAM
Addressing
00H
RAM and SFR Data M em ory Space
Figure 7-3: W79E825 and W79E824 RAM and SFR memory map
FFH
SFR
Direct
Addressing
Only
Unused
Indirect
RAM
80H
7FH
Direct & Indirect
RAM
Addressing
00H
RAM and SFR Data Memory Space
Figure 7-4: W79E823 and W79E822 RAM and SFR memory map
Since the scratch-pad RAM is only 256/128 bytes it can be used only when data contents are small.
There are several other special purpose areas within the scratch-pad RAM. These are described as
follows.
- 14 -
W79E825A/824A/823B/822B Data Sheet
FFH
Indirect RAM
80H
7FH
Direct RAM
30H
2FH
7F
7E
7D
7C
7B
7A
79
78
2EH
77
76
75
74
73
72
71
70
2DH
6F
6E
6D
6C
6B
6A
69
68
2CH
67
66
65
64
63
62
61
60
2BH
5F
5E
5D
5C
5B
5A
59
58
2AH
57
56
55
54
53
52
51
50
29H
4F
4E
4D
4C
4B
4A
49
48
40
28H
47
46
45
44
43
42
41
27H
3F
3E
3D
3C
3B
3A
39
38
26H
37
36
35
34
33
32
31
30
25H
2F
2E
2D
2C
2B
2A
29
28
24H
27
26
25
24
23
22
21
20
23H
1F
1E
1D
1C
1B
1A
19
18
22H
17
16
15
14
13
12
11
10
21H
0F
0E
0D
0C
0B
0A
09
08
20H
1FH
07
06
05
04
03
02
01
00
Bank 3
18H
17H
Bank 2
10H
0FH
Bank 1
08H
07H
Bank 0
00H
Figure 7-5: Scratch pad RAM
- 15 -
Publication Release Date: February 21, 2008
Revision A9
W79E825A/824A/823B/822B Data Sheet
7.4
Working Registers
There are four sets of working registers, each consisting of eight 8-bit registers. These are termed as
Banks 0, 1, 2, and 3. Individual registers within these banks can be directly accessed by separate
instructions. These individual registers are named as R0, R1, R2, R3, R4, R5, R6 and R7. However, at
one time the W79E825 series can work with only one particular bank. The bank selection is done by
setting RS1-RS0 bits in the PSW. The R0 and R1 registers are used to store the address for indirect
accessing.
7.5
Bit addressable Locations
The Scratch-pad RAM area from location 20h to 2Fh is byte as well as bit addressable. This means
that a bit in this area can be individually addressed. In addition some of the SFRs are also bit
addressable. The instruction decoder is able to distinguish a bit access from a byte access by the type
of the instruction itself. In the SFR area, any existing SFR whose address ends in a 0 or 8 is bit
addressable.
7.6
Stack
The scratch-pad RAM can be used for the stack. This area is selected by the Stack Pointer (SP),
which stores the address of the top of the stack. Whenever a jump, call or interrupt is invoked the
return address is placed on the stack. There is no restriction as to where the stack can begin in the
RAM. By default however, the Stack Pointer contains 07h at reset. The user can then change this to
any value desired. The SP will point to the last used value. Therefore, the SP will be incremented and
then address saved onto the stack. Conversely, while popping from the stack the contents will be read
first, and then the SP is decreased.
- 16 -
W79E825A/824A/823B/822B Data Sheet
8
SPECIAL FUNCTION REGISTERS
The W79E825 series uses Special Function Registers (SFRs) to control and monitor peripherals and
their Modes. The SFRs reside in the register locations 80-FFh and are accessed by direct addressing
only. Some of the SFRs are bit addressable. This is very useful in cases where users wish to modify a
particular bit without changing the others. The SFRs that are bit addressable are those whose
addresses end in 0 or 8. The W79E825 series contain all the SFRs present in the standard 8052.
However some additional SFRs are added. In some cases the unused bits in the original 8052, have
been given new functions. The list of the SFRs is as follows.
F8
IP1
F0
B
E8
EIE
E0
ACC
ADCCON
ADCH
D8
WDCON
PWMPL
PWM0L
PWM1L
D0
PSW
PWMPH
PWM0H
PWM1H
PWMCON1
P0ID
IP1H
PWM2L
PWM3L
PWMCON2
PWM2H
PWM3H
PWMCON3
NVMCON
NVMDAT
NVMADDR
TA
C8
C0
I2CON
I2ADDR
B8
IP0
SADEN
P0M1
B0
P0M2
P1M1
A8
IE
SADDR
A0
P2
KBI
98
SCON
SBUF
90
P1
88
TCON
TMOD
TL0
TL1
80
P0
SP
DPL
DPH
I2DAT
I2STATUS
I2CLK
I2TIMER
P1M2
P2M1
P2M2
IP0H
CMP1
CMP2
AUXR1
DIVM
TH0
TH1
CKCON
PCON
Table 8-1: Special Function Register Location Table
Note: 1. The SFRs in the column with dark borders are bit-addressable
2. The table is condensed with eight locations per row. Empty locations indicate that these are no registers at these
addresses. When a bit or register is not implemented, it will read high.
- 17 -
Publication Release Date: February 21, 2008
Revision A9
W79E825A/824A/823B/822B Data Sheet
SYMBOL
DEFINITION
BIT_ADDRESS, SYMBOL
ADDR MSB
LSB
ESS
Interrupt priority 1
F8H
(FF)
-
(FE)
-
(FD)
PPWM
IP1H
Interrupt high priority 1
F7H
-
-
PPWMH PWDIH
P0IDS
Port 0 Digital Input
Disable
F6H
B
B register
F0H
(F7)
(F6)
(F5)
(F4)
(F3)
(F2)
(F1)
(F0)
00000000B
EIE
Interrupt enable 1
E8H
(EF)
-
(EE)
-
(ED)
EPWM
(EC)
EWDI
(EB)
EC2
(EA)
EC1
(E9)
EKB
(E8)
EI2
xx000000B
ADCH
ADC converter result
E2H
ADC.9
ADC.8
ADC.7
ADC.6
ADC.5
ADC.4
ADC.3
ADC.2
xxxxxxxxB
ADCCON
ADC control register
E1H
ADC.1
ADC.0
ADCEX
ADCI
ADCS
RCCLK
AADR1
AADR0
xx000x00B
ACC
Accumulator
E0H
(E7)
(E6)
(E5)
(E4)
(E3)
(E2)
(E1)
(E0)
00000000B
BPEN
BKEN
PWM3B PWM2B PWM1B PWM0B 00000000B
IP1
PWMCON2 PWM control register 2
DFH
PWM3L
PWM 3 low bits register DEH
PWM2L
PWM 2 low bits register DDH
PWMCON1 PWM control register 1
PWM1L
DCH
(FC)
PWDI
RESET
(FB)
PC2
(FA)
PC1
(F9)
PKB
(F8)
PI2
xx000000B
PC2H
PC1H
PKBH
PI2H
xx000000B
00000000B
BKCH
BKPS
PWM3.7
PWM3.6 PWM3.5 PWM3.4 PWM3.3 PWM3.2 PWM3.1 PWM3.0 00000000B
PWM2.7
PWM2.6 PWM2.5 PWM2.4 PWM2.3 PWM2.2 PWM2.1 PWM2.0 00000000B
PWMRUN load
CF
CLRPWM PWM3I
PWM2I
PWM1I
PWM0I
00000000B
PWM 1 low bits register DBH
PWM1.7
PWM1.6 PWM1.5 PWM1.4 PWM1.3 PWM1.2 PWM1.1 PWM1.0 00000000B
PWM0L
PWM 0 low bits register DAH
PWM0.7
PWM0.6 PWM0.5 PWM0.4 PWM0.3 PWM0.2 PWM0.1 PWM0.0 00000000B
PWMPL
PWM counter low
register
D9H
PWMP0.7 PWMP0.6PWMP0.5PWMP0.4 PWMP0.3 PWMP0.2 PWMP0.1 PWMP0.0 00000000B
WDCON
Watch-Dog control
D8H
(DF)
WDRUN
PWMCON3 PWM control register 3
(DE)
-
(DD)
WD1
(DC)
WD0
(DB)
WDIF
(DA)
WTRF
(D9)
EWRST
(D8)
0x000000B
WDCLR
BKF
D7H
-
-
-
-
-
-
-
PWM3H
PWM 3 high bits register D6H
-
-
-
-
-
-
PWM3.9 PWM3.8 xxxxxx00B
xxxxxxx0B
PWM2H
PWM 2 high bits register D5H
-
-
-
-
-
-
PWM2.9 PWM2.8 xxxxxx00B
PWM1H
PWM 1 high bits register D3H
-
-
-
-
-
-
PWM1.9 PWM1.8 xxxxxx00B
PWM0H
PWM 0 high bits register D2H
-
-
-
-
-
-
PWM0.9 PWM0.8 xxxxxx00B
PWMPH
PWM counter high
register
D1H
-
-
-
-
-
-
PWMP0. PWMP0.
xxxxxx00B
9
8
PSW
Program status word
D0H
(D7)
CY
(D6)
AC
(D5)
F0
(D4)
RS1
(D3)
RS0
(D2)
OV
(D1)
F1
(D0)
P
00000000B
NVMDATA NVM Data
CFH
NVMCON
NVM Control
CEH
EER
EWR
-
-
-
-
-
-
00000000B
00000000B
TA
Timed Access
Protection
C7H
TA.7
TA.6
TA.5
TA.4
TA.3
TA.2
TA.1
TA.0
11111111B
NVMADDR NVM address
C6H
I2ADDR
I2C address1
C1H
ADDR.7
ADDR.6 ADDR.5 ADDR.4 ADDR.3 ADDR.2 ADDR.1 GC
xxxxxxx0B
I2CON
I2C Control register
C0H
(CF)
-
(CE)
ENS1
(CD)
STA
(CC)
STO
(CB)
SI
(CA)
AA
(C9)
-
(C8)
-
x00000xxB
I2TIMER
I2C Timer Counter
register
BFH
-
-
-
-
-
ENTI
DIV4
TIF
00000000B
I2CLK
I2C Clock Rate
BEH
I2CLK.7
I2CLK.6
I2CLK.5
I2CLK.4
I2CLK.3
I2CLK.2
I2CLK.1
I2CLK.0
00000000B
I2DAT.7
I2DAT.6 I2DAT.5 I2DAT.4 I2DAT.3 I2DAT.2 I2DAT.1 I2DAT.0 xxxxxxxxB
(BE)
PADC
(BD)
PBO
(BC)
PS
(BB)
PT1
(BA)
PX1
(B9)
PT0
(B8)
PX0
I2STATUS
BDH
I2DAT
BCH
SADEN
Slave address mask
00000000B
00000000B
B9H
00000000B
IP0
Interrupt priority
B8H
(BF)
-
IP0H
Interrupt high priority
B7H
-
PADCH
PBOH
PSH
PT1H
PX1H
PT0H
PX0H
x0000000B
P2M2
Port 2 output mode 2
B6H
-
-
-
-
-
-
P2M2.1
P2M2.0
xxxxxx00B
P2M1
Port 2 output mode 1
B5H
P2S
P1S
P0S
ENCLK
T1OE
T0OE
P2M1.1
P2M1.0
00000000B
P1M2
Port 1 output mode 2
B4H
P1M2.7
P1M2.6
-
P1M2.4
P1M2.3
P1M2.2
P1M2.1
P1M2.0
00000000B
P1M1
Port 1 output mode 1
B3H
P1M1.7
P1M1.6
-
P1M1.4
P1M1.3
P1M1.2
P1M1.1
P1M1.0
00000000B
P0M2
Port 0 output mode 2
B2H
P0M2.7
P0M2.6
P0M2.5
P0M2.4
P0M2.3
P0M2.2
P0M2.1
P0M2.0
00000000B
P0M1
Port 0 output mode 1
B1H
P0M1.7
P0M1.6
P0M1.5
P0M1.4
P0M1.3
P0M1.2
P0M1.1
P0M1.0
00000000B
- 18 -
x0000000B
W79E825A/824A/823B/822B Data Sheet
Continued
SYMBOL
DEFINITION
CMP2
Comparator 2 control
register
CMP1
BIT_ADDRESS, SYMBOL
ADDR MSB
LSB
ESS
RESET
ADH
-
-
CE2
CP2
CN2
OE2
CO2
CMF2
Comparator 1 control
register
ACH
-
-
CE1
CP1
CN1
OE1
CO1
CMF1
SADDR
Slave address
A9H
IE
Interrupt enable
A8H
(AF)
EA
(AE)
EADC
(AD)
EBO
(AC)
ES
(AB)
ET1
(AA)
EX1
(A9)
ET0
(A8)
EX0
KBF
BOD
BOI
LPBOV
SRST
ADCEN
0
DPS
AUXR1
AUX function register
A2H
KBI
Keyboard Interrupt
A1H
P2
Port 2
A0H
SBUF
Serial buffer
99H
00000000B
00000000B
00000000B
00000000B
000X0000B
00000000B
(A7)
-
(A6)
-
(A5)
-
(A4)
-
(A3)
-
(A2)
-
(A1)
XTAL1
(A0)
XTAL2
xxxxxx11B
CLKOUT
(9F)
SM0/FE
(9E)
SM1
(9D)
SM2
(9C)
REN
(9B)
TB8
(9A)
RB8
(99)
TI
(98)
RI
xxxxxxxxB
SCON
Serial control
98H
DIVM
uC clock divide register
95H
00000000B
P1
Port 1
90H
(97)
PWM2
(96)
PWM1
(95)
/RST
(94)
/INT1
(93)
/INT0
SDL
(92)
T0
SCL
(91)
RXD
(90)
TXD
11111111B
CKCON
Clock control
8EH
-
-
-
T1M
T0M
-
-
-
xxx00xxxB
TH1
Timer high 1
8DH
TH0
Timer high 0
8CH
00000000B
TL1
Timer low 1
8BH
00000000B
TL0
Timer low 0
8AH
TMOD
Timer mode
89H
GATE
C/T
M1
M0
GATE
C/T
M1
M0
TCON
Timer control
88H
(8F)
TF1
(8E)
TR1
(8D)
TF0
(8C)
TR0
(8B)
IE1
(8A)
IT1
(89)
IE0
(88)
IT0
00000000B
PCON
Power control
87H
SMOD
SMOD0
BOF
POR
GF1
GF0
PD
IDL
00xx0000B
00000000B
00000000B
00000000B
00000000B
DPH
Data pointer high
83H
00000000B
DPL
Data pointer low
82H
00000000B
SP
Stack pointer
81H
P0
Port 0
80H
00000111B
(87)
T1
(86)
AD3
CMP1
(85)
(84)
AD2
AD1
CMPREF CIN1A
(83)
AD0
CIN1B
(82)
BRAKE
CIN2A
(81)
PWM0
CIN2B
(80)
PWM3
CMP2
11111111B
Table 8-2: Special Function Registers
- 19 -
Publication Release Date: February 21, 2008
Revision A9
W79E825A/824A/823B/822B Data Sheet
PORT 0
Bit:
7
6
5
4
3
2
1
0
P0.7
P0.6
P0.5
P0.4
P0.3
P0.2
P0.1
P0.0
Mnemonic: P0
Address: 80h
P0.7-0: General purpose Input/Output port. Most instructions will read the port pins in case of a port
read access, however in case of read-modify-write instructions, the port latch is read. These alternate
functions are described below:
BIT
NAME
FUNCTION
7
P0.7
Timer 1 pin or KBI.7 pin of keypad input.
6
P0.6
CMP1 pin of analog comparator or KBI.6 pin of keypad input.
5
P0.5
CMPREF pin of analog comparator or KBI.5 pin of keypad input.
4
P0.4
CIN1A pin of analog comparator or KBI.4 pin of keypad input.
3
P0.3
CIN1B pin of analog comparator or KBI.3 pin of keypad input.
2
P0.2
BRAKE pin of PWM or CIN2A pin of analog comparator or KBI.2 pin of keypad input.
1
P0.1
PWM0 pin or CIN2B pin of analog comparator or KBI.1 pin of keypad input.
0
P0.0
PWM3 pin or CMP2 pin of analog comparator or KBI.0 pin of keypad input.
Note: The initial value of the port is set by CONFIG1.PRHI bit. The default setting for CONFIG1.PRHI =1 which the alternative
function output is turned on upon reset. If CONFIG1.PRHI is set to 0, the user has to write a 1 to port SFR to turn on the
alternative function output.
STACK POINTER
Bit:
7
6
5
4
3
2
1
0
SP.7
SP.6
SP.5
SP.4
SP.3
SP.2
SP.1
SP.0
Mnemonic: SP
Address: 81h
BIT
NAME
FUNCTION
7-0
SP.[7:0]
The Stack Pointer stores the Scratch-pad RAM address where the stack begins. In
other words it always points to the top of the stack.
DATA POINTER LOW
Bit:
7
6
5
4
3
2
1
0
DPL.7
DPL.6
DPL.5
DPL.4
DPL.3
DPL.2
DPL.1
DPL.0
Mnemonic: DPL
BIT
NAME
7-0
DPL.[7:0]
Address: 82h
FUNCTION
This is the low byte of the standard 8052 16-bit data pointer.
DATA POINTER HIGH
Bit:
7
6
5
4
3
2
1
0
DPH.7
DPH.6
DPH.5
DPH.4
DPH.3
DPH.2
DPH.1
DPH.0
Mnemonic: DPH
Address: 83h
- 20 -
W79E825A/824A/823B/822B Data Sheet
BIT
NAME
7-0
DPH.[7:0]
FUNCTION
This is the high byte of the standard 8052 16-bit data pointer.
This is the high byte of the DPTR 16-bit data pointer.
POWER CONTROL
Bit:
7
6
5
4
3
2
1
0
SMOD
SMOD0
BOF
POR
GF1
GF0
PD
IDL
Mnemonic: PCON
Address: 87h
BIT
NAME
FUNCTION
7
SMOD
1: This bit doubles the serial port baud rate in mode 1, 2, and 3.
6
SMOD0
0: Framing Error Detection Disable. SCON.7 (SM0/FE) bit is used as SM0
(standard 8052 function).
1: Framing Error Detection Enable. SCON.7 (SM0/FE) bit is used to reflect as
Frame Error (FE) status flag.
5
BOF
0: Cleared by software.
1: Set automatically when a brownout reset or interrupt has occurred. Also set at
power on.
4
POR
0: Cleared by software.
1: Set automatically when a power-on reset has occurred.
3
GF1
General purpose user flags.
2
GF0
General purpose user flags.
1
PD
1: The CPU goes into the POWER DOWN mode. In this mode, all the clocks are
stopped and program execution is frozen.
0
IDL
1: The CPU goes into the IDLE mode. In this mode, the clocks CPU clock
stopped, so program execution is frozen. But the clock to the serial, timer and
interrupt blocks is not stopped, and these blocks continue operating.
TIMER CONTROL
Bit:
7
6
5
4
3
2
1
0
TF1
TR1
TF0
TR0
IE1
IT1
IE0
IT0
Mnemonic: TCON
Address: 88h
BIT
NAME
FUNCTION
7
TF1
Timer 1 Overflow Flag. This bit is set when Timer 1 overflows. It is cleared
automatically when the program does a timer 1 interrupt service routine. Software
can also set or clear this bit.
6
TR1
Timer 1 Run Control. This bit is set or cleared by software to turn timer/counter on
or off.
- 21 -
Publication Release Date: February 21, 2008
Revision A9
W79E825A/824A/823B/822B Data Sheet
Continued
BIT
NAME
FUNCTION
5
TF0
Timer 0 Overflow Flag. This bit is set when Timer 0 overflows. It is cleared
automatically when the program does a timer 0 interrupt service routine. Software
can also set or clear this bit.
4
TR0
Timer 0 Run Control. This bit is set or cleared by software to turn timer/counter on
or off.
3
IE1
Interrupt 1 Edge Detect Flag: Set by hardware when an edge/level is detected on
INT1 . This bit is cleared by hardware when the service routine is vectored to only if
the interrupt was edge triggered. Otherwise it follows the inverse of the pin.
2
IT1
Interrupt 1 Type Control. Set/cleared by software to specify falling edge/ low level
triggered external inputs.
1
IE0
Interrupt 0 Edge Detect Flag. Set by hardware when an edge/level is detected on
INT0 . This bit is cleared by hardware when the service routine is vectored to only if
the interrupt was edge triggered. Otherwise it follows the inverse of the pin.
0
IT0
Interrupt 0 Type Control: Set/cleared by software to specify falling edge/ low level
triggered external inputs.
TIMER MODE CONTROL
Bit:
7
6
5
4
3
2
1
0
GATE
C/ T
M1
M0
GATE
C/ T
M1
M0
TIMER1
TIMER0
Mnemonic: TMOD
Address: 89h
BIT
NAME
FUNCTION
7
GATE
Gating control: When this bit is set, Timer/counter 1 is enabled only while the INT1
pin is high and the TR1 control bit is set. When cleared, the INT1 pin has no effect,
and Timer 1 is enabled whenever TR1 control bit is set.
6
C/ T
Timer or Counter Select: When clear, Timer 1 is incremented by the internal clock.
When set, the timer counts falling edges on the T1 pin.
5
M1
Timer 1 mode select bit 1. See table below.
4
M0
Timer 1 mode select bit 0. See table below.
3
GATE
2
C/ T
Timer or Counter Select: When clear, Timer 0 is incremented by the internal clock.
When set, the timer counts falling edges on the T0 pin.
1
M1
Timer 0 mode select bit 1. See table below.
0
M0
Timer 0 mode select bit 0. See table below.
Gating control: When this bit is set, Timer/counter 0 is enabled only while the INT0
pin is high and the TR0 control bit is set. When cleared, the INT0 pin has no effect,
and Timer 0 is enabled whenever TR0 control bit is set.
- 22 -
W79E825A/824A/823B/822B Data Sheet
M1, M0: Mode Select bits:
M1
M0
MODE
0
0
Mode 0: 8-bit timer/counter TLx serves as 5-bit pre-scale.
0
1
Mode 1: 16-bit timer/counter, no pre-scale.
1
0
Mode 2: 8-bit timer/counter with auto-reload from THx.
1
1
Mode 3: (Timer 0) TL0 is an 8-bit timer/counter controlled by the standard Timer0
control bits. TH0 is an 8-bit timer only controlled by Timer1 control bits.
(Timer 1) Timer/Counter 1 is stopped.
TIMER 0 LSB
Bit:
7
6
5
4
3
2
1
0
TL0.7
TL0.6
TL0.5
TL0.4
TL0.3
TL0.2
TL0.1
TL0.0
Mnemonic: TL0
BIT
NAME
7-0
TL0.[7:0]
Address: 8Ah
FUNCTION
Timer 0 LSB.
TIMER 1 LSB
Bit:
7
6
5
4
3
2
1
0
TL1.7
TL1.6
TL1.5
TL1.4
TL1.3
TL1.2
TL1.1
TL1.0
Mnemonic: TL1
BIT
NAME
7-0
TL1.[7:0]
Address: 8Bh
FUNCTION
Timer 1 LSB.
TIMER 0 MSB
Bit:
7
6
5
4
3
2
1
0
TH0.7
TH0.6
TH0.5
TH0.4
TH0.3
TH0.2
TH0.1
TH0.0
Mnemonic: TH0
BIT
NAME
7-0
TH0.[7:0]
Address: 8Ch
FUNCTION
Timer 0 MSB.
TIMER 1 MSB
Bit:
7
6
5
4
3
2
1
0
TH1.7
TH1.6
TH1.5
TH1.4
TH1.3
TH1.2
TH1.1
TH1.0
Mnemonic: TH1
BIT
NAME
7-0
TH1.[7:0]
Address: 8Dh
FUNCTION
Timer 1 MSB.
- 23 -
Publication Release Date: February 21, 2008
Revision A9
W79E825A/824A/823B/822B Data Sheet
CLOCK CONTROL
Bit:
7
6
5
4
3
2
1
0
-
-
-
T1M
T0M
-
-
-
Mnemonic: CKCON
Address: 8Eh
BIT
NAME
FUNCTION
7-5
-
4
T1M
Timer 1 clock select:
0: Timer 1 uses a divide by 12 clocks.
1: Timer 1 uses a divide by 4 clocks.
3
T0M
Timer 0 clock select:
0: Timer 0 uses a divide by 12 clocks.
1: Timer 0 uses a divide by 4 clocks.
2-0
-
Reserved.
Reserved.
PORT 1
Bit:
7
6
5
4
3
2
1
0
P1.7
P1.6
P1.5
P1.4
P1.3
P1.2
P1.1
P1.0
Mnemonic: P1
Address: 90h
P1.7-0: General purpose Input/Output port. Most instructions will read the port pins in case of a port
read access, however in case of read-modify-write instructions, the port latch is read. These alternate
functions are described below:
BIT
NAME
FUNCTION
7
P1.7
PWM 2 Pin.
6
P1.6
PWM 1 Pin.
5
P1.5
/RST Pin or Input Pin by alternative.
4
P1.4
/INT1 interrupt.
3
P1.3
/INT0 interrupt or SDA of I2C.
2
P1.2
Timer 0 or SCL of I2C.
1
P1.1
RXD of Serial port.
0
P1.0
TXD of Serial port.
Note: The initial value of the port is set by CONFIG1.PRHI bit. The default setting for CONFIG1.PRHI =1 which the alternative
function output is turned on upon reset. If CONFIG1.PRHI is set to 0, the user has to write a 1 to port SFR to turn on the
alternative function output.
DIVIDER CLOCK
Bit:
7
6
5
4
3
2
1
0
DIVM.7
DIVM.6
DIVM.5
DIVM.4
DIVM.3
DIVM.2
DIVM.1
DIVM.0
Mnemonic: DIVM
Address: 95h
- 24 -
W79E825A/824A/823B/822B Data Sheet
BIT
NAME
FUNCTION
7-0
DIVM.[7:0]
The DIVM register is clock divider of uC. Refer OSCILLATOR chapter.
SERIAL PORT CONTROL
Bit:
7
6
5
4
3
2
1
0
SM0/FE
SM1
SM2
REN
TB8
RB8
TI
RI
Mnemonic: SCON
BIT
Address: 98h
NAME
FUNCTION
7
SM0/FE
Serial port mode select bit 0 or Framing Error Flag: The SMOD0 bit in PCON SFR
determines whether this bit acts as SM0 or as FE. The operation of SM0 is
described below. When used as FE, this bit will be set to indicate an invalid stop
bit. This bit must be manually cleared in software to clear the FE condition.
6
SM1
Serial Port mode select bit 1. See table below.
SM2
Multiple processors communication. Setting this bit to 1 enables the multiprocessor
communication feature in mode 2 and 3. In mode 2 or 3, if SM2 is set to 1, then RI
will not be activated if the received 9th data bit (RB8) is 0. In mode 1, if SM2 = 1,
then RI will not be activated if a valid stop bit was not received. In mode 0, the SM2
bit controls the serial port clock. If set to 0, then the serial port runs at a divide by
12 clock of the oscillator. This gives compatibility with the standard 8052. When set
to 1, the serial clock become divide by 4 of the oscillator clock. This results in faster
synchronous serial communication.
4
REN
Receive enable:
0: Disable serial reception.
1: Enable serial reception.
3
TB8
This is the 9th bit to be transmitted in modes 2 and 3. This bit is set and cleared by
software as desired.
2
RB8
In modes 2 and 3 this is the received 9th data bit. In mode 1, if SM2 = 0, RB8 is the
stop bit that was received. In mode 0 it has no function.
1
TI
Transmit interrupt flag: This flag is set by hardware at the end of the 8th bit time in
mode 0, or at the beginning of the stop bit in all other modes during serial
transmission. This bit must be cleared by software.
RI
Receive interrupt flag: This flag is set by hardware at the end of the 8th bit time in
mode 0, or halfway through the stop bits time in the other modes during serial
reception. However the restrictions of SM2 apply to this bit. This bit can be cleared
only by software.
5
0
- 25 -
Publication Release Date: February 21, 2008
Revision A9
W79E825A/824A/823B/822B Data Sheet
SM0, SM1: Mode Select bits
MODE
SM0
SM1
DESCRIPTION
LENGTH
BAUD RATE
0
0
0
Synchronous
8
Tclk divided by 4 or 12
1
0
1
Asynchronous
10
Variable
2
1
0
Asynchronous
11
Tclk divided by 32 or 64
3
1
1
Asynchronous
11
Variable
SERIAL DATA BUFFER
Bit:
7
6
5
4
3
2
1
0
SBUF.7
SBUF.6
SBUF.5
SBUF.4
SBUF.3
SBUF.2
SBUF.1
SBUF.0
Mnemonic: SBUF
BIT
7-0
Address: 99h
NAME
FUNCTION
SBUF.[7:0]
Serial data on the serial port is read from or written to this location. It actually
consists of two separate internal 8-bit registers. One is the receive resister, and
the other is the transmit buffer. Any read access gets data from the receive data
buffer, while write access is to the transmit data buffer.
PORT 2
Bit:
7
6
5
4
3
2
1
0
-
-
-
-
-
-
P2.1
P2.0
Mnemonic: P2
Address: A0h
BIT
NAME
FUNCTION
7-2
-
1
P2.1
XTAL1 clock input pin.
0
P2.0
XTAL2 or CLKOUT pin by alternative.
Reserved
Note: The initial value of the port is set by CONFIG1.PRHI bit. The default setting for CONFIG1.PRHI =1 which the alternative
function output is turned on upon reset. If CONFIG1.PRHI is set to 0, the user has to write a 1 to port SFR to turn on the
alternative function output.
KEYBOARD INTERRUPT
Bit:
7
6
5
4
3
2
1
0
KBI.7
KBI.6
KBI.5
KBI.4
KBI.3
KBI.2
KBI.1
KBI.0
Mnemonic: KBI
Address: A1h
BIT
NAME
FUNCTION
7
KBI.7
1: Enable P0.7 as a cause of a Keyboard interrupt.
6
KBI.6
1: Enable P0.6 as a cause of a Keyboard interrupt.
5
KBI.5
1: Enable P0.5 as a cause of a Keyboard interrupt.
4
KBI.4
1: Enable P0.4 as a cause of a Keyboard interrupt.
- 26 -
W79E825A/824A/823B/822B Data Sheet
Continued .
BIT
NAME
FUNCTION
3
KBI.3
1: Enable P0.3 as a cause of a Keyboard interrupt.
2
KBI.2
1: Enable P0.2 as a cause of a Keyboard interrupt.
1
KBI.1
1: Enable P0.1 as a cause of a Keyboard interrupt.
0
KBI.0
1: Enable P0.0 as a cause of a Keyboard interrupt.
AUX FUNCTION REGISTER 1
Bit:
7
6
5
4
3
2
1
0
KBF
BOD
BOI
LPBOV
SRST
ADCEN
0
DPS
Mnemonic: AUXR1
BIT
Address: A2h
NAME
FUNCTION
7
KBF
Keyboard Interrupt Flag:
1: When any pin of port 0 that is enabled for the Keyboard Interrupt function goes
low. Must be cleared by software.
6
BOD
Brown Out Disable:
0: Enable Brownout Detect function.
1: Disable Brownout Detect function and save power.
BOI
Brown Out Interrupt:
0: Disable Brownout Detect Interrupt function and it will cause chip reset when
BOF is set.
1: This prevents Brownout Detection from causing a chip reset and allows the
Brownout Detect function to be used as an interrupt.
4
LPBOV
Low Power Brown Out Detect control:
0: When BOD is enable, the Brown Out detect is always turned on by normal run
or Power Down mode.
1: When BOD is enable, the Brown Out detect circuit is turned on by Power
Down mode. This control can help save 15/16 of the Brownout circuit power.
When uC is in Power Down mode, the BOD will enable internal RC OSC
(2MHz~0.5MHZ)
3
SRST
Software reset:
1: reset the chip as if a hardware reset occurred.
2
ADCEN
0: Disable ADC circuit.
1: Enable ADC circuit.
1
0
Reserved.
0
DPS
Dual Data Pointer Select
0: To select DPTR of standard 8051.
1: To select DPTR1
5
- 27 -
Publication Release Date: February 21, 2008
Revision A9
W79E825A/824A/823B/822B Data Sheet
INTERRUPT ENABLE
Bit:
7
6
5
4
3
2
1
0
EA
EADC
EBO
ES
ET1
EX1
ET0
EX0
Mnemonic: IE
BIT
Address: A8h
NAME
FUNCTION
7
EA
Global enable. Enable/Disable all interrupts.
6
EADC
Enable ADC interrupt.
5
EBO
Enable Brown Out interrupt.
4
ES
Enable Serial Port interrupt.
3
ET1
Enable Timer 1 interrupt.
2
EX1
Enable external interrupt 1.
1
ET0
Enable Timer 0 interrupt.
0
EX0
Enable external interrupt 0.
SLAVE ADDRESS
Bit:
7
6
5
4
3
2
1
0
SADDR.7
SADDR.6
SADDR.5
SADDR.4
SADDR.3
SADDR.2
SADDR.1
SADDR.0
Mnemonic: SADDR
Address: A9h
BIT
NAME
FUNCTION
7-0
SADDR.[7:0]
The SADDR should be programmed to the given or broadcast address for
serial port to which the slave processor is designated.
COMPARATOR 1 CONTROL REGISTER
Bit:
7
6
5
4
3
2
1
0
-
-
CE1
CP1
CN1
OE1
CO1
CMF1
Mnemonic: CMP1
BIT
Address: ACh
NAME
FUNCTION
7
-
Reserved.
6
-
Reserved.
CE1
Comparator enable:
0: Disable Comparator.
1: Enabled Comparator. Comparator output need wait stable 10 us after CE1 is
first set.
CP1
Comparator positive input select:
0: CIN1A is selected as the positive comparator input.
1: CIN1B is selected as the positive comparator input.
5
4
- 28 -
W79E825A/824A/823B/822B Data Sheet
Continued.
BIT
NAME
FUNCTION
CN1
Comparator negative input select:
0: The comparator reference pin CMPREF is selected as the negative
comparator input.
1: The internal comparator reference Vref is selected as the negative comparator
input.
2
OE1
Output enable:
1: The comparator output is connected to the CMP1 pin if the comparator is
enabled (CE1 = 1). This output is asynchronous to the CPU clock.
1
CO1
Comparator output:
Synchronized to the CPU clock to allow reading by software. Cleared when the
comparator is disabled (CE1 = 0).
CMF1
Comparator interrupt flag:
This bit is set by hardware whenever the comparator output CO1 changes state.
This bit will cause a hardware interrupt if enabled and of sufficient priority.
Cleared by software and when the comparator is disabled (CE1 = 0).
3
0
COMPARATOR 2 CONTROL REGISTER
Bit:
7
6
5
4
3
2
1
0
-
-
CE2
CP2
CN2
OE2
CO2
CMF2
Mnemonic: CMP2
BIT
Address: ADh
NAME
FUNCTION
7
-
Reserved.
6
-
Reserved.
5
CE2
Comparator enable:
0: Disable Comparator.
1: Enabled Comparator. Comparator output need wait stable 10 us after CE2 is
first set.
4
CP2
Comparator positive input select:
0: CIN2A is selected as the positive comparator input.
1: CIN2B is selected as the positive comparator input.
CN2
Comparator negative input select:
0: The comparator reference pin CMPREF is selected as the negative
comparator input.
1: The internal comparator reference Vref is selected as the negative comparator
input.
3
- 29 -
Publication Release Date: February 21, 2008
Revision A9
W79E825A/824A/823B/822B Data Sheet
Continued .
BIT
NAME
FUNCTION
2
OE2
Output enable:
1: The comparator output is connected to the CMP2 pin if the comparator is
enabled (CE2 = 1). This output is asynchronous to the CPU clock.
1
CO2
Comparator output:
Synchronized to the CPU clock to allow reading by software. Cleared when the
comparator is disabled (CE2 = 0).
CMF2
Comparator interrupt flag:
This bit is set by hardware whenever the comparator output CO2 changes state.
This bit will cause a hardware interrupt if enabled and of sufficient priority.
Cleared by software and when the comparator is disabled (CE2 = 0).
0
PORT 0 OUTPUT MODE 1
Bit:
7
6
5
4
3
2
1
0
P0M1.7
P0M1.6
P0M1.5
P0M1.4
P0M1.3
P0M1.2
P0M1.1
P0M1.0
Mnemonic: P0M1
BIT
NAME
7-0
P0M1.[7:0]
Address: B1h
FUNCTION
To control the output configuration of P0 bits [7:0]
PORT 0 OUTPUT MODE 2
Bit:
7
6
5
4
3
2
1
0
P0M2.7
P0M2.6
P0M2.5
P0M2.4
P0M2.3
P0M2.2
P0M2.1
P0M2.0
Mnemonic: P0M2
BIT
NAME
7-0
P0M2.[7:0]
Address: B2h
FUNCTION
To control the output configuration of P0 bits [7:0]
PORT 1 OUTPUT MODE 1
Bit:
7
6
5
4
3
2
1
0
P1M1.7
P1M1.6
-
P1M1.4
P1M1.3
P1M1.2
P1M1.1
P1M1.0
Mnemonic: P1M1
BIT
NAME
7-0
P1M1.[7:0]
Address: B3h
FUNCTION
To control the output configuration of P1 bits [7:0]
PORT 1 OUTPUT MODE 2
Bit:
7
6
5
4
3
2
1
0
P1M2.7
P1M2.6
-
P1M2.4
P1M2.3
P1M2.2
P1M2.1
P1M2.0
Mnemonic: P1M2
Address: B4h
- 30 -
W79E825A/824A/823B/822B Data Sheet
BIT
NAME
FUNCTION
7-0
P1M2.[7:0]
To control the output configuration of P1 bits [7:0]
PORT 2 OUTPUT MODE 1
Bit:
7
6
5
4
3
2
1
0
P2S
P1S
P0S
ENCLK
T1OE
T0OE
P2M1.1
P2M1.0
Mnemonic: P2M1
BIT
Address: B5h
NAME
FUNCTION
7
P2S
0: Disable Schmitt trigger inputs on port 2 and enable TTL inputs on port 2.
1: Enables Schmitt trigger inputs on Port 2.
6
P1S
0: Disable Schmitt trigger inputs on port 1 and enable TTL inputs on port 1.
1: Enables Schmitt trigger inputs on Port 1.
5
P0S
0: Disable Schmitt trigger inputs on port 0 and enable TTL inputs on port 0
1: Enables Schmitt trigger inputs on Port 0.
4
ENCLK
1: Enabled clock output to XTAL2 pin (P2.0)
3
T1OE
1: The P0.7 pin is toggled whenever Timer 1 overflows. The output frequency is
therefore one half of the Timer 1 overflow rate.
2
T0OE
1: The P1.2 pin is toggled whenever Timer 0 overflows. The output frequency is
therefore one half of the Timer 0 overflow rate.
1
P2M1.1
To control the output configuration of P2.1.
0
P2M1.0
To control the output configuration of P2.0.
PORT 2 OUTPUT MODE 2
Bit:
7
6
5
4
3
2
1
0
-
-
-
-
-
-
P2M2.1
P2M2.0
Mnemonic: P2M2
BIT
Address: B6h
NAME
FUNCTION
7-2
-
Reserved.
1-0
P2M2.[1:0]
To control the output configuration of P2 bits [1:0]
- 31 -
Publication Release Date: February 21, 2008
Revision A9
W79E825A/824A/823B/822B Data Sheet
Port Output Configuration Settings:
PXM1.Y
PXM2.Y
0
0
Quasi-bidirectional
PORT INPUT/OUTPUT MODE
0
1
Push-Pull
1
0
Input Only (High Impedance)
P2M1.PxS=0, TTL input
P2M1.PxS=1, Schmitt input
1
1
Open Drain
INTERRUPT HIGH PRIORITY
Bit:
7
6
5
4
3
2
1
0
-
PADCH
PBOH
PSH
PT1H
PX1H
PT0H
PX0H
Mnemonic: IP0H
BIT
Address: B7h
NAME
FUNCTION
7
-
This bit is un-implemented and will read high.
6
PADCH
1: To set interrupt high priority of ADC is highest priority level.
5
PBOH
1: To set interrupt high priority of Brown Out Detector is highest priority level.
4
PSH
1: To set interrupt high priority of Serial port 0 is highest priority level.
3
PT1H
1: To set interrupt high priority of Timer 1 is highest priority level.
2
PX1H
1: To set interrupt high priority of External interrupt 1 is highest priority level.
1
PT0H
1: To set interrupt high priority of Timer 0 is highest priority level.
0
PX0H
1: To set interrupt high priority of External interrupt 0 is highest priority level.
INTERRUPT PRIORITY 0
Bit:
7
6
5
4
3
2
1
0
-
PADC
PBO
PS
PT1
PX1
PT0
PX0
Mnemonic: IP
BIT
Address: B8h
NAME
FUNCTION
7
-
This bit is un-implemented and will read high.
6
PADC
1: To set interrupt priority of ADC is higher priority level.
5
PBO
1: To set interrupt priority of Brown Out Detector is higher priority level.
4
PS
1: To set interrupt priority of Serial port 0 is higher priority level.
3
PT1
1: To set interrupt priority of Timer 1 is higher priority level.
2
PX1
1: To set interrupt priority of External interrupt 1 is higher priority level.
1
PT0
1: To set interrupt priority of Timer 0 is higher priority level.
0
PX0
1: To set interrupt priority of External interrupt 0 is higher priority level.
- 32 -
W79E825A/824A/823B/822B Data Sheet
SLAVE ADDRESS MASK ENABLE
Bit:
7
6
5
4
3
2
1
0
SADEN.7
SADEN.6
SADEN.5
SADEN.4
SADEN.3
SADEN.2
SADEN.1
SADEN.0
Mnemonic: SADEN
BIT
7-0
Address: B9h
NAME
FUNCTION
SADEN [7:0]
This register enables the Automatic Address Recognition feature of the Serial
port 0. When a bit in the SADEN is set to 1, the same bit location in SADDR
will be compared with the incoming serial data. When SADEN is 0, then the
bit becomes a "don't care" in the comparison. This register enables the
Automatic Address Recognition feature of the Serial port 0. When all the bits
of SADEN are 0, interrupt will occur for any incoming address.
SLAVE ADDRESS MASK ENABLE 1
Bit:
7
6
5
4
3
2
1
0
I2DAT.7
I2DAT.6
I2DAT.5
I2DAT.4
I2DAT.3
I2DAT.2
I2DAT.1
I2DAT.0
Mnemonic: I2DAT
BIT
NAME
7-0
I2DAT.[7:0]
Address: BCh
FUNCTION
The data register of I2C.
I2C STATUS REGISTER
Bit:
7
6
5
4
3
I2STATUS.7 I2STATUS.6 I2STATUS.5 I2STATUS.4 I2STATUS.3
2
1
0
-
-
-
Mnemonic: I2STATUS
BIT
7-0
Address: BDh
NAME
FUNCTION
I2STATUS.[7:0]
The status register of I2C:
The three least significant bits are always 0. The five most significant bits
contain the status code. There are 23 possible status codes. When
I2STATUS contains F8H, no serial interrupt is requested. All other
I2STATUS values correspond to defined I2C states. When each of these
states is entered, a status interrupt is requested (SI = 1). A valid status
code is present in I2STATUS one machine cycle after SI is set by hardware
and is still present one machine cycle after SI has been reset by software.
In addition, states 00H stands for a Bus Error. A Bus Error occurs when a
START or STOP condition is present at an illegal position in the formation
frame. Example of illegal position are during the serial transfer of an
address byte, a data byte or an acknowledge bit.
I2C BAUD RATE CONTROL REGISTER
Bit:
7
6
5
4
3
2
1
0
I2CLK.7
I2CLK.6
I2CLK.5
I2CLK.4
I2CLK.3
I2CLK.2
I2CLK.1
I2CLK.0
Mnemonic: I2CLK
Address: BEh
- 33 -
Publication Release Date: February 21, 2008
Revision A9
W79E825A/824A/823B/822B Data Sheet
BIT
NAME
7-0
I2CLK.[7:0]
FUNCTION
The I2C clock rate bits.
I2C TIMER COUNTER REGISTER
Bit:
7
6
5
4
3
2
1
0
-
-
-
-
-
ENTI
DIV4
TIF
Mnemonic: I2TIMER
BIT
7~3
2
1
0
Address: BFh
NAME
FUNCTION
-
Reserved.
ENTI
Enable I2C 14-bits Timer Counter:
0: Disable 14-bits Timer Counter count.
1: Enable 14-bits Timer Counter count. After enable ENTI and ENSI, the 14-bit
counter will be counted. When SI flag of I2C is set, the counter will stop to
count and 14-bits Timer Counter will be cleared.
DIV4
I2C Timer Counter clock source divide function:
0: The 14-bits Timer Counter source clock is Fosc clock.
1: The 14-bits Timer Counter source clock is divided by 4.
TIF
The I2C Timer Counter count flag:
0: The 14-bits Timer Counter is not overflow.
1: The 14-bits Timer Counter is overflow. Before enable I2C Timer (both ENTI,
ENSI = [1,1]) the SI must be cleared. If I2C interrupt is enabled. The I2C
interrupt service routine will be executed. This bit is cleared by software.
I2C CONTROL REGISTER
Bit:
7
6
5
4
3
2
1
-
ENSI
STA
STO
SI
AA
-
Mnemonic: I2CON
BIT
7
6
NAME
0
-
Address: C0h
FUNCTION
-
Reserved.
ENS1
0: Disable I2C Serial Function. The SDA and SCL output are in a high impedance
state. SDA and SCL input signals are ignored, I2C is not in the addressed slave
mode or it is not addressable, and STO bit in I2CON is forced to “0”. No other bits
are affected. P1.2 (SCL) and P1.3 (SDA) may be used as open drain I/O ports.
1: Enable I2C Serial Function. The P1.2 and P1.3 port latches must be to logic 1.
- 34 -
W79E825A/824A/823B/822B Data Sheet
Continued
BIT
NAME
FUNCTION
STA
The START flag.
0: The STA bit is reset, no START condition or repeated START condition will be
generated.
1: The STA bit is set to enter a master mode. The I2C hardware checks the status of
I2C bus and generates a START condition if the bus is free. If bus is not free, then
I2C waits for a STOP condition and generates a START condition after a delay. If
STA is set while I2C is already in a master mode and one or more bytes are
transmitted or received, I2C transmits a repeated START condition. STA may be
set any time. STA may also be set when I2C interface is an addressed slave
mode.
STO
The bit STO bit is set while I2C is in a master mode. A STOP condition is transmitted
to the I2C bus. When the STOP condition is detected on the bus, the I2C hardware
clears the STO flag. In a slave mode, the STO flag may be set to recover from a bus
error condition. In this case, no STOP condition is transmitted to the I2C bus.
However, the I2C hardware behaves as if a STOP condition has been received and it
switches to the not addressable slave receiver mode. The STO flag is automatically
cleared by hardware. If the STA and STO bits are both set, then a STOP condition is
transmitted to the I2C bus if I2C is in a master mode (in a slave mode, I2C generates
an internal STOP condition which is not transmitted). I2C then transmits a START
condition.
SI
0: When the SI flag is reset, no serial interrupt is requested, and there is no stretching
on the serial clock on the SCL line.
1: When a new SIO state is present in the I2STATUS register, the SI flag is set by
hardware, and, if the EA and ES bits (in IE register) are both set, a serial interrupt
is requested when SI is set. The only state that does not cause SI to be set is state
F8H, which indicates that no relevant state information is available. When SI is set,
the low period of the serial clock on the SCL line is stretched, and the serial
transfer is suspended. A high level on the SCL line is unaffected by the serial
interrupt flag. SI must be cleared by software.
2
AA
The Assert Acknowledge Flag
0: A not acknowledge (high level to SDA) will be returned during the acknowledge
clock pulse on SCL when: 1) A data has been received while SIO is in the master
receiver mode. 2) A data byte has been received while SIO is in the addressed
slave receiver mode.
1: An acknowledge (low level to SDA) will be returned during the acknowledge clock
pulse on the SCL line when: 1) The own slave address has been received. 2) A
data byte has been received while SIO is in the master receiver mode. 3) A data
byte has been received while SIO is in the addressed slave receiver mode. 4) The
General Call address has been received while the general call bit (GC) in I2ADDR
is set.
1
-
Reserved.
0
-
Reserved.
5
4
3
- 35 -
Publication Release Date: February 21, 2008
Revision A9
W79E825A/824A/823B/822B Data Sheet
I2C ADDRESS REGISTER
Bit:
7
6
5
4
3
2
1
0
I2ADDR.7
I2ADDR.6
I2ADDR.5
I2ADDR.4
I2ADDR.3
I2ADDR.2
I2ADDR.1
GC
Mnemonic: I2ADDR
BIT
Address: C1h
NAME
FUNCTION
I2C Address register:
The 8051 uC can read from and write to this 8-bit, directly addressable
I2ADDR.[7:1] SFR. The content of this register is irrelevant when I2C is in master mode.
In the slave mode, the seven most significant bits must be loaded with the
MCU’s own address. The I2C hardware will react if either of the address is
matched.
7~1
0
General Call Function.
0: Disable General Call Function.
1: Enable General Call Function.
GC
NVM ADDRESS
Bit:
7
6
5
4
3
2
1
0
NVMADDR.7 NVMADDR.6 NVMADDR.5 NVMADDR.4 NVMADDR.3 NVMADDR.2NVMADDR.1 NVMADDR.0
Mnemonic: NVMADDR
Address: C6h
BIT
NAME
FUNCTION
7~0
NVMADDR.[7:0]
The NVM address:
The register indicates NVM data memory of low byte address on On-Chip
code memory space.
TIMED ACCESS
Bit:
7
6
5
4
3
2
1
0
TA.7
TA.6
TA.5
TA.4
TA.3
TA.2
TA.1
TA.0
Mnemonic: TA
BIT
7-0
Address: C7h
NAME
FUNCTION
TA.[7:0]
The Timed Access register:
The Timed Access register controls the access to protected bits. To access
protected bits, the user must first write AAH to the TA. This must be immediately
followed by a write of 55H to TA. Now a window is opened in the protected bits
for three machine cycles, during which the user can write to these bits.
NVM CONTROL
Bit:
7
6
5
4
3
2
1
0
EER
EWR
-
-
-
-
-
-
Mnemonic: NVMCON
Address: CEh
- 36 -
W79E825A/824A/823B/822B Data Sheet
BIT
7
6
5-0
NAME
FUNCTION
EER
NVM page(n) erase bit:
0: Without erase NVM page(n).
1: Set this bit to erase page(n) of NVM. The NVM has 4 pages and each page
have 64 bytes data memory. Before select page by NVMADDR register that
will automatic enable page area, after set this bit, the page will be erased and
program counter will halt at this instruction. After finished, program counter will
kept next instruction then executed. The NVM page’s address is defined in
table below.
EWR
NVM data write bit:
0: Without write NVM data.
1: Set this bit to write NVM bytes and program counter will halt at this instruction.
After write is finished, program counter will kept next instruction then executed.
-
Reserved
NVM Page(n) Area Definition Table:
PAGE
START ADDRESS
END ADDRESS
0
00H
3FH
1
40H
7FH
2
80H
BFH
3
C0H
FFH
Note: The W79E823 and W79E822 without page 2 and page 3.
NVM DATA
Bit:
7
6
NVMDAT.7
5
4
3
2
NVMDAT.6 NVMDAT.5 NVMDAT.4 NVMDAT3
1
NVMDAT.2 NVMDAT.1 NVMDAT.0
Mnemonic: NVMDATA
BIT
NAME
7~0
NVMDAT.[7:0]
0
Address: CFh
FUNCTION
The NVM data write register. The read NVM data is by MOVC instruction.
PROGRAM STATUS WORD
Bit:
7
6
5
4
3
2
1
0
CY
AC
F0
RS1
RS0
OV
F1
P
Mnemonic: PSW
BIT
7
Address: D0h
NAME
CY
FUNCTION
Carry flag:
Set for an arithmetic operation which results in a carry being generated from the
ALU. It is also used as the accumulator for the bit operations.
- 37 -
Publication Release Date: February 21, 2008
Revision A9
W79E825A/824A/823B/822B Data Sheet
Continued
BIT
6
NAME
FUNCTION
AC
Auxiliary carry:
Set when the previous operation resulted in a carry from the high order nibble.
F0
User flag 0:
The General purpose flag that can be set or cleared by the user.
RS1~RS0
Register bank select bits.
2
OV
Overflow flag:
Set when a carry was generated from the seventh bit but not from the 8th bit as
a result of the previous operation, or vice-versa.
1
F1
User Flag 1:
The General purpose flag that can be set or cleared by the user software.
0
P
Parity flag:
Set/cleared by hardware to indicate odd/even number of 1's in the accumulator.
5
4~3
RS.1-0: Register Bank Selection Bits:
RS1
RS0
REGISTER BANK
ADDRESS
0
0
0
00-07h
0
1
1
08-0Fh
1
0
2
10-17h
1
1
3
18-1Fh
PWMP COUNTER HIGH BITS REGISTER
Bit:
7
6
5
4
3
2
1
0
-
-
-
-
-
-
PWMP.9
PWMP.8
Mnemonic: PWMPH
BIT
Address: D1h
NAME
FUNCTION
7-2
-
Reserved.
1-0
PWMP.[9:8]
The PWM Counter Register bits 9~8.
PWM 0 HIGH BITS REGISTER
Bit:
7
6
5
4
3
2
1
0
-
-
-
-
-
-
PWM0.9
PWM0.8
Mnemonic: PWM0H
BIT
Address: D2h
NAME
FUNCTION
7~2
-
Reserved.
1~0
PWM0.[9:8]
The PWM 0 High Bits Register bit 9~8.
- 38 -
W79E825A/824A/823B/822B Data Sheet
PWM 1 HIGH BITS REGISTER
Bit:
7
6
5
4
3
2
1
0
-
-
-
-
-
-
PWM1.9
PWM1.8
Mnemonic: PWM1H
BIT
Address: D3h
NAME
FUNCTION
7~2
-
Reserved.
1~0
PWM1.[9:8]
The PWM 1 High Bits Register bit 9~8.
PWM 2 HIGH BITS REGISTER
Bit:
7
6
5
4
3
2
1
0
-
-
-
-
-
-
PWM2.9
PWM2.8
Mnemonic: PWM2H
BIT
Address: D5h
NAME
FUNCTION
7~2
-
Reserved.
1~0
PWM2.[9:8]
The PWM 2 High Bits Register bit 9~8.
PWM 3 HIGH BITS REGISTER
Bit:
7
6
5
4
3
2
1
0
-
-
-
-
-
-
PWM3.9
PWM3.8
Mnemonic: PWM3H
BIT
Address: D6h
NAME
FUNCTION
7~2
-
Reserved.
1~0
PWM3.[9:8]
The PWM 3 High Bits Register bit 9~8.
PWM CONTROL REGISTER 3
Bit:
7
6
5
4
3
2
1
0
-
-
-
-
-
-
-
BKF
Mnemonic: PWMCON3
BIT
7-6
0
NAME
Address: D7h
FUNCTION
-
Reserved.
BKF
The external brake pin Flag.
0: The PWM is not brake.
1: The PWM is brake by external brake pin. It will be cleared by software.
WATCHDOG CONTROL
Bit:
7
6
5
4
3
2
1
0
WDRUN
POR
WD1
WD0
WDIF
WTRF
EWRST
WDCLR
Mnemonic: WDCON
Address: D8h
- 39 -
Publication Release Date: February 21, 2008
Revision A9
W79E825A/824A/823B/822B Data Sheet
BIT
NAME
FUNCTION
7
WDRUN
0: The Watchdog is stopped.
1: The Watchdog is running.
6
-
Reserved.
5
WD1
Watchdog Timer Time-out Select bits. These bits determine the time-out period
of the watchdog timer. The reset time-out period is 512 clocks longer than the
watchdog time-out.
WD1
4
WD0
WD0
Interrupt time-out
Reset time-out
17
217 + 512
0
0
2
0
1
220
220 + 512
1
0
223
223 + 512
1
1
226
226 + 512
WDIF
Watchdog Timer Interrupt Flag
0: If the interrupt is not enabled, then this bit indicates that the time-out period
has elapsed. This bit must be cleared by software.
1: If the watchdog interrupt is enabled, hardware will set this bit to indicate that
the watchdog interrupt has occurred.
2
WTRF
Watchdog Timer Reset Flag
1: Hardware will set this bit when the watchdog timer causes a reset. Software
can read it but must clear it manually. A power-fail reset will also clear the
bit. This bit helps software in determining the cause of a reset. If EWRST =
0, the watchdog timer will have no affect on this bit.
1
EWRST
0: Disable Watchdog Timer Reset.
1: Enable Watchdog Timer Reset.
WDCLR
Reset Watchdog Timer
This bit helps in putting the watchdog timer into a know state. It also helps in
resetting the watchdog timer before a time-out occurs. Failing to set the
EWRST before time-out will cause an interrupt, if EWDI (EIE.4) is set, and 512
clocks after that a watchdog timer reset will be generated if EWRST is set. This
bit is self-clearing by hardware.
3
0
The WDCON SFR is set to 0x000000B on a reset. WTRF (WDCON.2) is set to a 1 on a Watchdog
timer reset, but to a 0 on power on/down resets. WTRF (WDCON.2) is not altered by an external
reset. EWRST (WDCON.1) is set to 0 on a Power-on reset, reset pin reset, and Watch Dog Timer
reset.
All the bits in this SFR have unrestricted read access. WDRUN, WD0, WD1, EWRST, WDIF and
WDCLR require Timed Access procedure to write. The remaining bits have unrestricted write
accesses. Please refer TA register description.
- 40 -
W79E825A/824A/823B/822B Data Sheet
TA
WDCON
MOV
MOV
SETB
ORL
MOV
MOV
ORL
REG
C7H
REG
D8H
TA, #AAH
TA, #55H
WDCON.0
WDCON, #00110000B
TA, #AAH
TA, #55H
WDCON, #00000010B
; To access protected bits
; Reset watchdog timer
; Select 26 bits watchdog timer
; Enable watchdog
PWMP COUNTER LOW BITS REGISTER
Bit:
7
6
5
4
3
2
1
0
PWMP.7
PWMP.6
PWMP.5
PWP.4
PWMP.3
PWMP.2
PWMP.1
PWMP.1
Mnemonic: PWMPL
BIT
7~0
Address: D9h
NAME
FUNCTION
PWMP.[7:0]
PWM Counter Low Bits Register.
PWM0 LOW BITS REGISTER
Bit:
7
6
5
4
3
2
1
0
PWM0.7
PWM0.6
PWM0.5
PWM0.4
PWM0.3
PWM0.2
PWM0.1
PWM0.1
Mnemonic: PWM0L
BIT
7~0
Address: DAh
NAME
FUNCTION
PWM0.[7:0]
PWM 0 Low Bits Register.
PWM1 LOW BITS REGISTER
Bit:
7
6
5
4
3
2
1
0
PWM1.7
PWM1.6
PWM1.5
PWM1.4
PWM1.3
PWM1.2
PWM1.1
PWM1.0
Mnemonic: PWM1L
BIT
7~0
Address: DBh
NAME
FUNCTION
PWM1.[7:0]
PWM 1 Low Bits Register.
PWM CONTROL REGISTER 1
Bit:
7
6
5
4
3
2
1
0
PWMRUN
Load
CF
CLRPWM
PWM3I
PWM2I
PWM1I
PWM0I
Mnemonic: PWMCON1
Address: DCh
- 41 -
Publication Release Date: February 21, 2008
Revision A9
W79E825A/824A/823B/822B Data Sheet
BIT
NAME
FUNCTION
7
PWMRUN
0: The PWM is not running.
1: The PWM counter is running.
6
Load
0: The registers value of PWMP and PWMn are never loaded to counter and
Comparator registers.
1: The PWMP and PWMn registers load value to counter and compare registers
at the counter underflow. This bit is auto cleared by hardware at next clock
cycle.
5
CF
0: The 10-bit counter down count is not underflow.
1: The 10-bit counter down count is underflow. This bit is Software clear.
4
CLRPWM
1: Clear 10-bit PWM counter to 000H. This bit is auto cleared by hardware.
3
PWM3I
0: PWM3 out is non-inverted.
1: PWM3 output is inverted.
2
PWM2I
0: PWM2 out is non-inverted.
1: PWM2 output is inverted.
1
PWM1I
0: PWM1 out is non-inverted.
1: PWM1 output is inverted.
0
PWM0I
0: PWM0 out is non-inverted.
1: PWM0 output is inverted.
PWM2 LOW BITS REGISTER
Bit:
7
6
5
4
3
2
1
0
PWM2.7
PWM2.6
PWM2.5
PWM2.4
PWM2.3
PWM2.2
PWM2.1
PWM2.0
Mnemonic: PWM2L
BIT
7~0
Address: DDh
NAME
FUNCTION
PWM2.[7:0] PWM 2 Low Bits Register.
PWM3 LOW BITS REGISTER
Bit:
7
6
5
4
3
2
1
0
PWM3.7
PWM3.6
PWM3.5
PWM3.4
PWM3.3
PWM3.2
PWM3.1
PWM3.0
Mnemonic: PWM3L
BIT
7~0
Address: DEh
NAME
FUNCTION
PWM3.[7:0] PWM 3 Low Bits Register.
PWM CONTROL REGISTER 2
Bit:
7
6
5
4
3
2
1
0
BKCH
BKPS
BPEN
BKEN
PWM3B
PWM2B
PWM1B
PWM0B
Mnemonic: PWMCON2
Address: DFh
- 42 -
W79E825A/824A/823B/822B Data Sheet
BIT
NAME
FUNCTION
7
BKCH
See the below table, when BKEN is set.
6
BKPS
0: Brake is asserted if P0.2 is low.
1: Brake is asserted if P0.2 is high
5
BPEN
See the below table, when BKEN is set.
4
BKEN
0: The Brake is never asserted.
1: The Brake is enabled, and see the below table.
3
PWM3B
0: The PWM3 output is low, when Brake is asserted.
1: The PWM3 output is high, when Brake is asserted.
2
PWM2B
0: The PWM2 output is low, when Brake is asserted.
1: The PWM2 output is high, when Brake is asserted.
1
PWM1B
0: The PWM1 output is low, when Brake is asserted.
1: The PWM1 output is high, when Brake is asserted.
0
PWM0B
0: The PWM0 output is low, when Brake is asserted.
1: The PWM0 output is high, when Brake is asserted.
Brake Condition Table:
BPEN
BKCH
BRAKE CONDITION
0
Brake On (software brake and keeping brake).
Software brake condition. When active (BPEN=BKCH=0, and BKEN=1), PWM
output follows PWMnB setting. This brake has no effect on PWMRUN bit,
therefore, internal PWM generator continues to run. When the brake is released,
the state of PWM output depends on the current state of PWM generator output
during the release.
1
Brake On, when PWM is not running (PWMRUN=0), the PWM output condition
follows PWMnB setting.
When the brake is released (by disabling BKEN = 0), the PWM output resumes
to the state when PWM generator stop running prior to enabling the brake.
Brake Off, when PWM is running (PWMRUN=1).
1
0
Brake On, when Brake Pin asserted.
External pin brake condition. When active (by external pin), PWM output follows
PWMnB setting, PWMRUN will be cleared by hardware, and BKF flag will be set.
When the brake is released (by de-asserting the external pin and disabling
BKEN = 0), the PWM output resumes to the state of the PWM generator output
prior to the brake.
1
1
No any active.
0
0
ACCUMULATOR
Bit:
7
6
5
4
3
2
1
0
ACC.7
ACC.6
ACC.5
ACC.4
ACC.3
ACC.2
ACC.1
ACC.0
Mnemonic: ACC
Address: E0h
- 43 -
Publication Release Date: February 21, 2008
Revision A9
W79E825A/824A/823B/822B Data Sheet
BIT
NAME
7-0
ACC.[7:0]
FUNCTION
The A or ACC register is the standard 8052 accumulator
ADC CONTROL REGISTER
Bit:
7
6
5
4
3
2
1
0
ADC.1
ADC.0
ADCEX
ADCI
ADCS
RCCLK
AADR1
AADR0
Mnemonic: ADCCON
BIT
Address: E1h
NAME
FUNCTION
7
ADC.1
The ADC conversion result.
6
ADC.0
The ADC conversion result.
ADCEX
Enable STADC-triggered conversion
0: Conversion can only be started by software (i.e., by setting ADCS).
1: Conversion can be started by software or by a rising edge on STADC (pin
P1.4).
ADCI
ADC Interrupt flag:
This flag is set when the result of an A/D conversion is ready. This generates an
ADC interrupt, if it is enabled. The flag may be cleared by the ISR. While this flag
is 1, the ADC cannot start a new conversion. ADCI can not be set by software.
3
ADCS
ADC Start and Status: Set this bit to start an A/D conversion. It may also be set
by STADC if ADCEX is 1. This signal remains high while the ADC is busy and is
reset right after ADCI is set.
Notes:
1. It is recommended to clear ADCI before ADCS is set. However, if ADCI is
cleared and ADCS is set at the same time, a new A/D conversion may start
on the same channel.
2. Software clearing of ADCS will abort conversion in progress.
3. ADC cannot start a new conversion while ADCS or ADCI is high.
2
RCCLK
0: The CPU clock is used as ADC clock.
1: The internal RC clock is used as ADC clock.
1
AADR1
The ADC input select. See table below.
0
AADR0
The ADC input select. See table below.
5
4
The ADCI and ADCS control the ADC conversion as below:
ADCI
ADCS
ADC STATUS
0
0
ADC not busy; A conversion can be started.
0
1
ADC busy; Start of a new conversion is blocked.
1
0
Conversion completed; Start of a new conversion requires ADCI = 0.
1
1
This is an internal temporary state that user can ignore it.
- 44 -
W79E825A/824A/823B/822B Data Sheet
AADR1, AADR0: ADC Analog Input Channel select bits:
These bits can only be changed when ADCI and ADCS are both zero.
AADR1
AADR0
SELECTED ANALOG INPUT CHANNEL
0
0
AD0 (P0.3)
0
1
AD1 (P0.4)
1
0
AD2 (P0.5)
1
1
AD3 (P0.6)
ADC CONVERTER RESULT HIGH REGISTER
Bit:
7
6
5
4
3
2
1
0
ADC.9
ADC.8
ADC.7
ADC.6
ADC.5
ADC.4
ADC.3
ADC.2
Mnemonic: ADCH
BIT
NAME
7-0
ADC.[9:2]
Address: E2h
FUNCTION
The ADC conversion result.
INTERRUPT ENABLE REGISTER 1
Bit:
7
6
5
4
3
2
1
0
-
-
EPWM
EWDI
EC2
EC1
EKB
EI2
Mnemonic: EIE
BIT
Address: E8h
NAME
FUNCTION
7
-
Reserved.
6
-
Reserved.
5
EPWM
0: Disable PWM Interrupt when external brake pin was brake.
1: Enable PWM Interrupt when external brake pin was brake.
4
EWDI
0: Disable Watchdog Timer Interrupt.
1: Enable Watchdog Timer Interrupt.
3
EC2
0: Disable Comparator 2 Interrupt.
1: Enable Comparator 2 Interrupt.
2
EC1
0: Disable Comparator 1 Interrupt.
1: Enable Comparator 1 Interrupt.
1
EKB
0: Disable Keypad Interrupt.
1: Enable Keypad Interrupt.
0
EI2
0: Disable I2C Interrupt.
1: Enable I2C Interrupt.
- 45 -
Publication Release Date: February 21, 2008
Revision A9
W79E825A/824A/823B/822B Data Sheet
B REGISTER
Bit:
7
6
5
4
3
2
1
0
B.7
B.6
B.5
B.4
B.3
B.2
B.1
B.0
Mnemonic: B
Address: F0h
BIT
NAME
FUNCTION
7-0
B.[7:0]
The B register is the standard 8052 register that serves as a second accumulator.
PORT 0 DIGITAL INPUT DISABLE
Bit:
7
6
5
4
3
2
1
0
P0ID.7
P0ID.6
P0ID.5
P0ID.4
P0ID.3
P0ID.2
P0ID.1
P0ID.0
Mnemonic: P0ID
BIT
7~0
Address: F6h
NAME
P0ID.[7:0]
FUNCTION
Enable/Disable Port 0 digital inputs.
0: Enable Port 0 digital inputs.
1: Disable Port 0 digital inputs.
INTERRUPT HIGH PRIORITY 1
Bit:
7
6
5
4
3
2
1
0
-
-
PPWMH
PWDIH
PC2H
PC1H
PKBH
PI2H
Mnemonic: IP1H
BIT
Address: F7h
NAME
FUNCTION
7
-
Reserved.
6
-
Reserved.
5
PPWMH
1: To set interrupt high priority of PWM’s brake is highest priority level.
4
PWDIH
1: To set interrupt high priority of Watchdog is highest priority level.
3
PC2H
1: To set interrupt high priority of Comparator 2 is highest priority level.
2
PC1H
1: To set interrupt high priority of Comparator 1 is highest priority level.
1
PKBH
1: To set interrupt high priority of Keypad is highest priority level.
0
PI2H
1: To set interrupt high priority of I2C is highest priority level.
- 46 -
W79E825A/824A/823B/822B Data Sheet
EXTENDED INTERRUPT PRIORITY
Bit:
7
6
5
4
3
2
1
0
-
-
PPWM
PWDI
PC2
PC1
PKB
PI2
Mnemonic: IP1
BIT
Address: F8h
NAME
FUNCTION
7
-
Reserved.
6
-
Reserved.
5
PPWM
1: To set interrupt priority of PWM’s external brake is higher priority level.
4
PWDI
1: To set interrupt priority of Watchdog is higher priority level.
3
PC2
1: To set interrupt priority of Comparator 2 is higher priority level.
2
PC1
1: To set interrupt priority of Comparator 1 is higher priority level.
1
PKB
1: To set interrupt priority of Keypad is higher priority level.
0
PI2
1: To set interrupt priority of I2C is higher priority level.
- 47 -
Publication Release Date: February 21, 2008
Revision A9
W79E825A/824A/823B/822B Data Sheet
9
INSTRUCTION SET
The W79E825 series execute all the instructions of the standard 8052 family. The operations of these
instructions, as well as their effects on flag and status bits, are exactly the same. However, the timing
of these instructions is different in two ways. Firstly, the machine cycle is four clock periods, while the
standard-8051/52 machine cycle is twelve clock periods. Secondly, it can fetch only once per machine
cycle (i.e., four clocks per fetch), while the standard 8051/52 can fetch twice per machine cycle (i.e.,
six clocks per fetch).
The timing differences create an advantage for the W79E825 series. There is only one fetch per
machine cycle, so the number of machine cycles is usually equal to the number of operands in the
instruction. (Jumps and calls do require an additional cycle to calculate the new address.) As a result,
the W79E825 series reduces the number of dummy fetches and wasted cycles, and therefore
improves overall efficiency, compared to the standard 8051/52.
OP-CODE
HEX CODE
BYTES
W79E825
SERIES
MACHINE
CYCLE
W79E825
SERIES
CLOCK
CYCLES
8032
CLOCK
CYCLES
W79E825
SERIES VS.
8032 SPEED
RATIO
NOP
00
1
1
4
12
3
ADD A, R0
28
1
1
4
12
3
ADD A, R1
29
1
1
4
12
3
ADD A, R2
2A
1
1
4
12
3
ADD A, R3
2B
1
1
4
12
3
ADD A, R4
2C
1
1
4
12
3
ADD A, R5
2D
1
1
4
12
3
ADD A, R6
2E
1
1
4
12
3
ADD A, R7
2F
1
1
4
12
3
ADD A, @R0
26
1
1
4
12
3
ADD A, @R1
27
1
1
4
12
3
ADD A, direct
25
2
2
8
12
1.5
ADD A, #data
24
2
2
8
12
1.5
ADDC A, R0
38
1
1
4
12
3
ADDC A, R1
39
1
1
4
12
3
ADDC A, R2
3A
1
1
4
12
3
ADDC A, R3
3B
1
1
4
12
3
ADDC A, R4
3C
1
1
4
12
3
ADDC A, R5
3D
1
1
4
12
3
ADDC A, R6
3E
1
1
4
12
3
ADDC A, R7
3F
1
1
4
12
3
ADDC A, @R0
36
1
1
4
12
3
ADDC A, @R1
37
1
1
4
12
3
- 48 -
W79E825A/824A/823B/822B Data Sheet
Continued
OP-CODE
HEX CODE
BYTES
W79E825
SERIES
MACHINE
CYCLE
W79E825
SERIES
CLOCK
CYCLES
8032
CLOCK
CYCLES
W79E825
SERIES VS.
8032 SPEED
RATIO
ADDC A, direct
35
2
2
8
12
1.5
ADDC A, #data
34
2
2
8
12
1.5
SUBB A, R0
98
1
1
4
12
3
SUBB A, R1
99
1
1
4
12
3
SUBB A, R2
9A
1
1
4
12
3
SUBB A, R3
9B
1
1
4
12
3
SUBB A, R4
9C
1
1
4
12
3
SUBB A, R5
9D
1
1
4
12
3
SUBB A, R6
9E
1
1
4
12
3
SUBB A, R7
9F
1
1
4
12
3
SUBB A, @R0
96
1
1
4
12
3
SUBB A, @R1
97
1
1
4
12
3
SUBB A, direct
95
2
2
8
12
1.5
SUBB A, #data
94
2
2
8
12
1.5
INC A
04
1
1
4
12
3
INC R0
08
1
1
4
12
3
INC R1
09
1
1
4
12
3
INC R2
0A
1
1
4
12
3
INC R3
0B
1
1
4
12
3
INC R4
0C
1
1
4
12
3
INC R5
0D
1
1
4
12
3
INC R6
0E
1
1
4
12
3
INC R7
0F
1
1
4
12
3
INC @R0
06
1
1
4
12
3
INC @R1
07
1
1
4
12
3
INC direct
05
2
2
8
12
1.5
INC DPTR
A3
1
2
8
24
3
DEC A
14
1
1
4
12
3
DEC R0
18
1
1
4
12
3
DEC R1
19
1
1
4
12
3
DEC R2
1A
1
1
4
12
3
DEC R3
1B
1
1
4
12
3
- 49 -
Publication Release Date: February 21, 2008
Revision A9
W79E825A/824A/823B/822B Data Sheet
Continued
OP-CODE
HEX CODE
BYTES
W79E825
SERIES
MACHINE
CYCLE
W79E825
SERIES
CLOCK
CYCLES
8032
CLOCK
CYCLES
W79E825
SERIES VS.
8032 SPEED
RATIO
DEC R4
1C
1
1
4
12
3
DEC R5
1D
1
1
4
12
3
DEC R6
1E
1
1
4
12
3
DEC R7
1F
1
1
4
12
3
DEC @R0
16
1
1
4
12
3
DEC @R1
17
1
1
4
12
3
DEC direct
15
2
2
8
12
1.5
MUL AB
A4
1
5
20
48
2.4
DIV AB
84
1
5
20
48
2.4
DA A
D4
1
1
4
12
3
ANL A, R0
58
1
1
4
12
3
ANL A, R1
59
1
1
4
12
3
ANL A, R2
5A
1
1
4
12
3
ANL A, R3
5B
1
1
4
12
3
ANL A, R4
5C
1
1
4
12
3
ANL A, R5
5D
1
1
4
12
3
ANL A, R6
5E
1
1
4
12
3
ANL A, R7
5F
1
1
4
12
3
ANL A, @R0
56
1
1
4
12
3
ANL A, @R1
57
1
1
4
12
3
ANL A, direct
55
2
2
8
12
1.5
ANL A, #data
54
2
2
8
12
1.5
ANL direct, A
52
2
2
8
12
1.5
ANL direct, #data
53
3
3
12
24
2
ORL A, R0
48
1
1
4
12
3
ORL A, R1
49
1
1
4
12
3
ORL A, R2
4A
1
1
4
12
3
ORL A, R3
4B
1
1
4
12
3
ORL A, R4
4C
1
1
4
12
3
ORL A, R5
4D
1
1
4
12
3
ORL A, R6
4E
1
1
4
12
3
ORL A, R7
4F
1
1
4
12
3
- 50 -
W79E825A/824A/823B/822B Data Sheet
Continued
OP-CODE
HEX CODE
BYTES
W79E825
SERIES
MACHINE
CYCLE
W79E825
SERIES
CLOCK
CYCLES
8032
CLOCK
CYCLES
W79E825
SERIES VS.
8032 SPEED
RATIO
ORL A, @R0
46
1
1
4
12
3
ORL A, @R1
47
1
1
4
12
3
ORL A, direct
45
2
2
8
12
1.5
ORL A, #data
44
2
2
8
12
1.5
ORL direct, A
42
2
2
8
12
1.5
ORL direct, #data
43
3
3
12
24
2
XRL A, R0
68
1
1
4
12
3
XRL A, R1
69
1
1
4
12
3
XRL A, R2
6A
1
1
4
12
3
XRL A, R3
6B
1
1
4
12
3
XRL A, R4
6C
1
1
4
12
3
XRL A, R5
6D
1
1
4
12
3
XRL A, R6
6E
1
1
4
12
3
XRL A, R7
6F
1
1
4
12
3
XRL A, @R0
66
1
1
4
12
3
XRL A, @R1
67
1
1
4
12
3
XRL A, direct
65
2
2
8
12
1.5
XRL A, #data
64
2
2
8
12
1.5
XRL direct, A
62
2
2
8
12
1.5
XRL direct, #data
63
3
3
12
24
2
CLR A
E4
1
1
4
12
3
CPL A
F4
1
1
4
12
3
RL A
23
1
1
4
12
3
RLC A
33
1
1
4
12
3
RR A
03
1
1
4
12
3
RRC A
13
1
1
4
12
3
SWAP A
C4
1
1
4
12
3
MOV A, R0
E8
1
1
4
12
3
MOV A, R1
E9
1
1
4
12
3
MOV A, R2
EA
1
1
4
12
3
MOV A, R3
EB
1
1
4
12
3
MOV A, R4
EC
1
1
4
12
3
- 51 -
Publication Release Date: February 21, 2008
Revision A9
W79E825A/824A/823B/822B Data Sheet
Continued
OP-CODE
HEX CODE
BYTES
W79E825
SERIES
MACHINE
CYCLE
W79E825
SERIES
CLOCK
CYCLES
8032
CLOCK
CYCLES
W79E825
SERIES VS.
8032 SPEED
RATIO
MOV A, R5
ED
1
1
4
12
3
MOV A, R6
EE
1
1
4
12
3
MOV A, R7
EF
1
1
4
12
3
MOV A, @R0
E6
1
1
4
12
3
MOV A, @R1
E7
1
1
4
12
3
MOV A, direct
E5
2
2
8
12
1.5
MOV A, #data
74
2
2
8
12
1.5
MOV R0, A
F8
1
1
4
12
3
MOV R1, A
F9
1
1
4
12
3
MOV R2, A
FA
1
1
4
12
3
MOV R3, A
FB
1
1
4
12
3
MOV R4, A
FC
1
1
4
12
3
MOV R5, A
FD
1
1
4
12
3
MOV R6, A
FE
1
1
4
12
3
MOV R7, A
FF
1
1
4
12
3
MOV R0, direct
A8
2
2
8
12
1.5
MOV R1, direct
A9
2
2
8
12
1.5
MOV R2, direct
AA
2
2
8
12
1.5
MOV R3, direct
AB
2
2
8
12
1.5
MOV R4, direct
AC
2
2
8
12
1.5
MOV R5, direct
AD
2
2
8
12
1.5
MOV R6, direct
AE
2
2
8
12
1.5
MOV R7, direct
AF
2
2
8
12
1.5
MOV R0, #data
78
2
2
8
12
1.5
MOV R1, #data
79
2
2
8
12
1.5
MOV R2, #data
7A
2
2
8
12
1.5
MOV R3, #data
7B
2
2
8
12
1.5
MOV R4, #data
7C
2
2
8
12
1.5
MOV R5, #data
7D
2
2
8
12
1.5
MOV R6, #data
7E
2
2
8
12
1.5
MOV R7, #data
7F
2
2
8
12
1.5
MOV @R0, A
F6
1
1
4
12
3
- 52 -
W79E825A/824A/823B/822B Data Sheet
Continued
OP-CODE
HEX CODE
BYTES
W79E825
SERIES
MACHINE
CYCLE
W79E825
SERIES
CLOCK
CYCLES
8032
CLOCK
CYCLES
W79E825
SERIES VS.
8032 SPEED
RATIO
MOV @R1, A
F7
1
1
4
12
3
MOV @R0, direct
A6
2
2
8
12
1.5
MOV @R1, direct
A7
2
2
8
12
1.5
MOV @R0, #data
76
2
2
8
12
1.5
MOV @R1, #data
77
2
2
8
12
1.5
MOV direct, A
F5
2
2
8
12
1.5
MOV direct, R0
88
2
2
8
12
1.5
MOV direct, R1
89
2
2
8
12
1.5
MOV direct, R2
8A
2
2
8
12
1.5
MOV direct, R3
8B
2
2
8
12
1.5
MOV direct, R4
8C
2
2
8
12
1.5
MOV direct, R5
8D
2
2
8
12
1.5
MOV direct, R6
8E
2
2
8
12
1.5
MOV direct, R7
8F
2
2
8
12
1.5
MOV direct, @R0
86
2
2
8
12
1.5
MOV direct, @R1
87
2
2
8
12
1.5
MOV direct, direct
85
3
3
12
24
2
MOV direct, #data
75
3
3
12
24
2
MOV DPTR, #data
16
90
3
3
12
24
2
MOVC A,
@A+DPTR
93
1
2
8
24
3
MOVC A, @A+PC
83
1
2
8
24
3
MOVX A, @R0
E2
1
2-9
8 - 36
24
3 - 0.66
MOVX A, @R1
E3
1
2-9
8 - 36
24
3 - 0.66
MOVX A, @DPTR
E0
1
2-9
8 - 36
24
3 - 0.66
MOVX @R0, A
F2
1
2-9
8 - 36
24
3 - 0.66
MOVX @R1, A
F3
1
2-9
8 - 36
24
3 - 0.66
MOVX @DPTR, A
F0
1
2-9
8 - 36
24
3 - 0.66
PUSH direct
C0
2
2
8
24
3
POP direct
D0
2
2
8
24
3
XCH A, R0
C8
1
1
4
12
3
XCH A, R1
C9
1
1
4
12
3
- 53 -
Publication Release Date: February 21, 2008
Revision A9
W79E825A/824A/823B/822B Data Sheet
Continued
OP-CODE
HEX CODE
BYTES
W79E825
SERIES
MACHINE
CYCLE
W79E825
SERIES
CLOCK
CYCLES
8032
CLOCK
CYCLES
W79E825
SERIES VS.
8032 SPEED
RATIO
XCH A, R2
CA
1
1
4
12
3
XCH A, R3
CB
1
1
4
12
3
XCH A, R4
CC
1
1
4
12
3
XCH A, R5
CD
1
1
4
12
3
XCH A, R6
CE
1
1
4
12
3
XCH A, R7
CF
1
1
4
12
3
XCH A, @R0
C6
1
1
4
12
3
XCH A, @R1
C7
1
1
4
12
3
XCHD A, @R0
D6
1
1
4
12
3
XCHD A, @R1
D7
1
1
4
12
3
XCH A, direct
C5
2
2
8
12
1.5
CLR C
C3
1
1
4
12
3
CLR bit
C2
2
2
8
12
1.5
SETB C
D3
1
1
4
12
3
SETB bit
D2
2
2
8
12
1.5
CPL C
B3
1
1
4
12
3
CPL bit
B2
2
2
8
12
1.5
ANL C, bit
82
2
2
8
24
3
ANL C, /bit
B0
2
2
6
24
3
ORL C, bit
72
2
2
8
24
3
ORL C, /bit
A0
2
2
6
24
3
MOV C, bit
A2
2
2
8
12
1.5
MOV bit, C
92
2
2
8
24
3
ACALL addr11
71, 91, B1,
11, 31, 51,
D1, F1
2
3
12
24
2
LCALL addr16
12
3
4
16
24
1.5
RET
22
1
2
8
24
3
RETI
32
1
2
8
24
3
AJMP ADDR11
01, 21, 41,
61, 81, A1,
C1, E1
2
3
12
24
2
LJMP addr16
02
3
4
16
24
1.5
JMP @A+DPTR
73
1
2
6
24
3
- 54 -
W79E825A/824A/823B/822B Data Sheet
Continued
OP-CODE
HEX CODE
BYTES
W79E825
SERIES
MACHINE
CYCLE
W79E825
SERIES
CLOCK
CYCLES
8032
CLOCK
CYCLES
W79E825
SERIES VS.
8032 SPEED
RATIO
SJMP rel
80
2
3
12
24
2
JZ rel
60
2
3
12
24
2
JNZ rel
70
2
3
12
24
2
JC rel
40
2
3
12
24
2
JNC rel
50
2
3
12
24
2
JB bit, rel
20
3
4
16
24
1.5
JNB bit, rel
30
3
4
16
24
1.5
JBC bit, rel
10
3
4
16
24
1.5
CJNE A, direct, rel
B5
3
4
16
24
1.5
CJNE A, #data, rel
B4
3
4
16
24
1.5
CJNE @R0, #data,
rel
B6
3
4
16
24
1.5
CJNE @R1, #data,
rel
B7
3
4
16
24
1.5
CJNE R0, #data, rel
B8
3
4
16
24
1.5
CJNE R1, #data, rel
B9
3
4
16
24
1.5
CJNE R2, #data, rel
BA
3
4
16
24
1.5
CJNE R3, #data, rel
BB
3
4
16
24
1.5
CJNE R4, #data, rel
BC
3
4
16
24
1.5
CJNE R5, #data, rel
BD
3
4
16
24
1.5
CJNE R6, #data, rel
BE
3
4
16
24
1.5
CJNE R7, #data, rel
BF
3
4
16
24
1.5
DJNZ R0, rel
D8
2
3
12
24
2
DJNZ R1, rel
D9
2
3
12
24
2
DJNZ R5, rel
DD
2
3
12
24
2
DJNZ R2, rel
DA
2
3
12
24
2
DJNZ R3, rel
DB
2
3
12
24
2
DJNZ R4, rel
DC
2
3
12
24
2
DJNZ R6, rel
DE
2
3
12
24
2
DJNZ R7, rel
DF
2
3
12
24
2
DJNZ direct, rel
D5
3
4
16
24
1.5
Table 9-1: Instruction Set for W79E825/824/823/822
- 55 -
Publication Release Date: February 21, 2008
Revision A9
W79E825A/824A/823B/822B Data Sheet
9.1
Instruction Timing
This section is important because some applications use software instructions to generate timing
delays. It also provides more information about timing differences between the W79E825 series and
the standard 8051/52.
In W79E825 series, each machine cycle is four clock periods long. Each clock period is called a state,
and each machine cycle consists of four states: C1, C2 C3 and C4, in order. Both clock edges are
used for internal timing, so the duty cycle of the clock should be as close to 50% as possible to avoid
timing conflicts.
The W79E825 series does one op-code fetch per machine cycle, so, in most instructions, the number
of machine cycles required is equal to the number of bytes in the instruction. There are 256 available
op-codes. 128 of them are single-cycle instructions, so many op-codes are executed in just four clocks
period. Some of the other op-codes are two-cycle instructions, and most of these have two-byte opcodes. However, there are some instructions that have one-byte instructions yet take two cycles to
execute. One important example is the MOVX instruction.
In the standard 8052, the MOVX instruction is always two machine cycles long. However, in the
W79E825 series each machine cycle is made of only 4 clock periods compared to the 12 clock
periods for the standard 8052. Therefore, even though the number of categories has increased, each
instruction is at least 1.5 to 3 times faster than the standard 8052 in terms of clock periods.
Single Cycle
C1
C2
C3
C4
CPU CLK
ALE
PSEN
A7-0
AD<7:0>
Data_ in D7-0
Address A15-8
Address <15:0>
Figure 9-1: Single Cycle Instruction Timing
- 56 -
W79E825A/824A/823B/822B Data Sheet
Operand Fetch
Instruction Fetch
C1
C2
C3
C4
C1
C2
C3
C4
CPU CLK
ALE
PSEN
PC
AD<7:0>
Address<15:0>
OP-CODE
PC+1
Address A15-8
OPERAND
Address A15-8
Figure 9-2: Two Cycles Instruction Timing
Instruction Fetch
C1
C2
C3
Operand Fetch
C4
C1
C2
C3
Operand Fetch
C4
C1
C2
C3
C4
CPU CLK
ALE
PSEN
AD<7:0>
Address<15:0>
A7-0
OP-CODE
Address A15-8
A7-0
OPERAND
Address A15-8
A7-0
OPERAND
Address A15-8
Figure 9-3: Three Cycles Instruction Timing
- 57 -
Publication Release Date: February 21, 2008
Revision A9
W79E825A/824A/823B/822B Data Sheet
Instruction Fetch
C1
C2
C3
Operand Fetch
C4
C1
C2
C3
Operand Fetch
C4
C1
C2
C3
Operand Fetch
C4
C1
C2
C3
C4
CPU CLK
ALE
PSEN
AD<7:0>
A7-0
Address<15:0>
A7-0
OP-CODE
A7-0
OPERAND
Address A15-8
Address A15-8
A7-0
OPERAND
Address A15-8
OPERAND
Address A15-8
Figure 9-4: Four Cycles Instruction Timing
Instruction Fetch
C1
C2
C3
C4
Operand Fetch
C1
C2
C3
C4
Operand Fetch
C1
C2
C3
C4
Operand Fetch
C1
C2
C3
C4
Operand Fetch
C1
C2
C3
C4
CPU CLK
ALE
PSEN
AD<7:0>
A7-0 OP-CODE
A7-0 OPERAND
A7-0 OPERAND
A7-0 OPERAND
A7-0 OPERAND
Address<15:0>
Address A15-8
Address A15-8
Address A15-8
Address A15-8
Address A15-8
Figure 9-5: Five Cycles Instruction Timing
- 58 -
W79E825A/824A/823B/822B Data Sheet
10 POWER MANAGEMENT
The W79E825 series has several features that help the user to control the power consumption of the
device. These modes are discussed in the next two sections.
10.1 Idle Mode
The user can put the device into idle mode by writing 1 to the bit PCON.0. The instruction that sets the
idle bit is the last instruction that will be executed before the device goes into Idle Mode. In the Idle
mode, the clock to the CPU is halted, but not to the Interrupt, Timer, Watchdog timer, I2C, PWM and
Serial port blocks. This forces the CPU state to be frozen; the Program counter, the Stack Pointer, the
Program Status Word, the Accumulator and the other registers hold their contents. The port pins hold
the logical states they had at the time Idle was activated. The Idle mode can be terminated in two
ways. Since the interrupt controller is still active, the activation of any enabled interrupt can wake up
the processor. This will automatically clear the Idle bit, terminate the Idle mode, and the Interrupt
Service Routine (ISR) will be executed. After the ISR, execution of the program will continue from the
instruction which put the device into Idle Mode.
The Idle mode can also be exited by activating the reset. The device can put into reset either by
applying a low on the external /RST pin, a Power on reset condition or a Watchdog timer reset. The
external reset pin has to be held low for at least two machine cycles i.e. 8 clock periods to be
recognized as a valid reset. In the reset condition the program counter is reset to 0000h and all the
SFRs are set to the reset condition. Since the clock is already running there is no delay and execution
starts immediately. In the Idle mode, the Watchdog timer continues to run, and if enabled, a time-out
will cause a watchdog timer interrupt which will wake up the device. The software must reset the
Watchdog timer in order to preempt the reset which will occur after 512 clock periods of the time-out.
When the W79E825 series are exiting from an Idle Mode with a reset, the instruction following the one
which put the device into Idle Mode is not executed. So there is no danger of unexpected writes.
10.2 Power Down Mode
The device can be put into Power Down mode by writing 1 to bit PCON.1. The instruction that does
this will be the last instruction to be executed before the device goes into Power Down mode. In the
Power Down mode, all the clocks are stopped and the device comes to a halt. All activity is completely
stopped and the power consumption is reduced to the lowest possible value. The port pins output the
values held by their respective SFRs.
The W79E825 series will exit the Power Down mode with a reset or by an external interrupt pin
enabled as level detected. An external reset can be used to exit the Power down state. The low on
/RST pin terminates the Power Down mode, and restarts the clock. The program execution will restart
from 0000h. In the Power down mode, the clock is stopped, so the Watchdog timer cannot be used to
provide the reset to exit Power down mode when its clock source is external OSC or crystal.
The sources that can wake up from the power down mode are external interrupts, keyboard interrupt
(KBI), brownout reset (BOR), and comparator interrupt (CMF1, CMF2).
The W79E825 series can be waken up from the Power Down mode by forcing an external interrupt pin
activation, provided the corresponding interrupt is enabled, while the global enable (EA) bit is set. If
these conditions are met, then either a low-level or a falling-edge at external interrupt pin will re-start
the oscillator. The device will then execute the interrupt service routine for the corresponding external
interrupt. After the interrupt service routine is completed, the program execution returns to the
instruction after one which put the device into Power Down mode and continues from there. During
Power down mode, if AUXR1.LPBOV = 1 and AUXR1.BOD = 0, the internal RC clock will be enabled
and hence save power.
- 59 -
Publication Release Date: February 21, 2008
Revision A9
W79E825A/824A/823B/822B Data Sheet
11 RESET CONDITIONS
The user has several hardware related options for placing the W79E825 series into reset condition. In
general, most register bits go to their reset value irrespective of the reset condition, but there are a few
flags whose state depends on the source of reset. The user can use these flags to determine the
cause of reset using software.
11.1 Sources of reset
11.1.1 External Reset
The device samples the /RST pin every machine cycle during state C4. The /RST pin must be held
low for at least two machine cycles before the reset circuitry applies an internal reset signal. Thus, this
reset is a synchronous operation and requires the clock to be running.
The device remains in the reset state as long as /RST is low and remains low up to two machine
cycles after /RST is deactivated. Then, the device begins program execution at 0000h. There are no
flags associated with the external reset, but, since the other two reset sources do have flags, the
external reset is the cause if those flags are clear.
11.1.2 Power-On Reset (POR)
The software must clear the POR flag after reading it. Otherwise it will not be possible to correctly
determine future reset sources. If the power fails, then the device will once again go into reset state.
When the power returns to the proper operating levels, the device will again perform a power on reset
delay and set the POR flag.
11.1.3 Watchdog Timer Reset
The Watchdog Timer is a free-running timer with programmable time-out intervals. The program must
clear the Watchdog Timer before the time-out interval is reached to restart the count. If the time-out
interval is reached, an interrupt flag is set. 512 clocks later, if the Watchdog Reset is enabled and the
Watchdog Timer has not been cleared, the Watchdog Timer generates a reset. The reset condition is
maintained by the hardware for two machine cycles, and the WTRF bit in WDCON is set. Afterwards,
the device begins program execution at 0000h.
11.2 Reset State
When the device is reset, most registers return to their initial state. The Watchdog Timer is disabled if
the reset source was a power-on reset. The port registers are set to FFh, which puts most of the port
pins in a high state. The Program Counter is set to 0000h, and the stack pointer is reset to 07h. After
this, the device remains in the reset state as long as the reset conditions are satisfied.
Reset does not affect the on-chip RAM, however, so RAM is preserved as long as VDD remains
above approximately 2 V, the minimum operating voltage for the RAM. If VDD falls below 2 V, the
RAM contents are also lost. In either case, the stack pointer is always reset, so the stack contents are
lost.
- 60 -
W79E825A/824A/823B/822B Data Sheet
SFR RESET VALUE
SFR NAME
RESET VALUE
SFR NAME
RESET VALUE
P0
1111 1111B
I2DAT
xxxx xxxxB
SP
0000 0111B
I2STATUS
0000 0xxxB
DPL
0000 0000B
I2TIMER
0000 0000B
DPH
0000 0000B
I2CLK
0000 0000B
PCON
00xx 0000B
I2CON
0000 0000B
TCON
0000 0000B
I2ADDR
xxxx xxxxB
TMOD
0000 0000B
TA
1111 1111B
TL0
0000 0000B
PSW
0000 0000B
TL1
0000 0000B
PWMP1
xxxx xx00B
TH0
0000 0000B
PWM0H
xxxx xx00B
TH1
0000 0000B
PWM1H
xxxx xx00B
CKCON
0000 0000B
PWM2H
xxxx xx00B
P1
1111 xx11B
PWM3H
xxxx xx00B
DIVM
0000 0000B
WDCON
0x00 0000B
SCON
0000 0000B
PWMP0
0000 0000B
SBUF
xxxx xxxxB
PWM0L
0000 0000B
P2
xxx xx11B
PWM1L
0000 0000B
KBI
0000 0000B
PWMCON1
0000 0000B
AUXR1
0000 0000B
PWM2L
0000 0000B
IE
0000 0000B
PWM3L
0000 0000B
SADDR
0000 0000B
PWMCON2
0000 0000B
CMP1
0000 0000B
PWMCON3
xxxxxxx0B
CMP2
0000 0000B
ACC
0000 0000B
P0M1
0000 0000B
ADCCON
xx00 0x00B
P0M2
0000 0000B
ADCH
xxxx xxxxB
P1M1
0000 0000B
EIE
xx000 000B
P1M2
0000 0000B
B
0000 0000B
P2M1
0000 0000B
P0IDS
0000 0000B
P2M2
xxxx xx00B
IPH
xx00 0000B
IP0H
x000 0000B
IP1
xx00 0000B
IP0
x000 0000B
NVMADDR
0000 0000B
SADEN
0000 0000B
NVMDAT
0000 0000B
NVMCON
00xx xxxxB
Table 11-1: SFR Reset Value
- 61 -
Publication Release Date: February 21, 2008
Revision A9
W79E825A/824A/823B/822B Data Sheet
The WDCON SFR bits are set/cleared in reset condition depending on the source of the reset.
External reset
Watchdog reset
Power on reset
WDCON
0x0x0xx0B
0x0x01x0B
01000000B
The WDCON SFR is set to a 0x00 0000B on the reset. WTRF (WDCON.2) is set to a 1 on a
Watchdog timer reset, but to a 0 on power on/down resets. WTRF (WDCON.2) is not altered by
external reset. EWRST (WDCON.1) is cleared by any reset. Software or any reset will clear
WDIF(WDCON.3) bit.
Some of the bits in the WDCON SFR (WDRUN, WDCLR, EWRST, WDIF, WD0 and WD1) have
unrestricted read access which required Timed Access procedure to write. The remaining bits have
unrestricted write accesses. Please refer TA register description.
- 62 -
W79E825A/824A/823B/822B Data Sheet
VBO3.8 (BOR Enable)
VBO3.8
VBO3.8 (BOR Enable)
WDG Normal Run
WDG Stop
System Normal Run
System Stop
2 Watchdog
timer clocks
Crystal
65536 clocks
Internal RC
256 clocks
Crystal
65536 clocks
Internal RC
256 clocks
512 Watchdog
timer clocks
Figure 11-1: Internal reset and VDD monitor timing diagram
- 63 -
Publication Release Date: February 21, 2008
Revision A9
W79E825A/824A/823B/822B Data Sheet
VBO3.8 (BOR Enable)
0.7VDD
0.3VDD
At least 4 clocks
System Normal Run
System within Power Down Mode
System Stop
System not in Power Down Mode
Crystal
65536 clocks
Internal RC
Crystal
65536 clocks
Internal RC
256 clocks
256 clocks
Figure 11-2: External reset timing diagram
- 64 -
W79E825A/824A/823B/822B Data Sheet
12 INTERRUPTS
The W79E825 series have four priority level interrupts structure with 13 interrupt sources. Each of the
interrupt sources has an individual priority bit, flag, interrupt vector and enable bit. In addition, the
interrupts can be globally enabled or disabled.
12.1 Interrupt Sources
The External Interrupts INT0 and INT1 can be either edge triggered or level triggered, depending on
bits IT0 and IT1. The bits IE0 and IE1 in the TCON register are the flags which are checked to
generate the interrupt. In the edge triggered mode, the INTx inputs are sampled in every machine
cycle. If the sample is high in one cycle and low in the next, then a high to low transition is detected
and the interrupts request flag IEx in TCON is set. The flag bit requests the interrupt. Since the
external interrupts are sampled every machine cycle, they have to be held high or low for at least one
complete machine cycle. The IEx flag is automatically cleared when the service routine is called. If the
level triggered mode is selected, then the requesting source has to hold the pin low till the interrupt is
serviced. The IEx flag will not be cleared by the hardware on entering the service routine. If the
interrupt continues to be held low even after the service routine is completed, then the processor may
acknowledge another interrupt request from the same source.
The Timer 0 and 1 Interrupts are generated by the TF0 and TF1 flags. These flags are set by the
overflow in the Timer 0 and Timer 1. The TF0 and TF1 flags are automatically cleared by the hardware
when the timer interrupt is serviced. The Watchdog timer can be used as a system monitor or a simple
timer. In either case, when the time-out count is reached, the Watchdog Timer interrupt flag WDIF
(WDCON.3) is set. If the interrupt is enabled by the enable bit EIE.4, then an interrupt will occur.
The Serial block can generate interrupt on reception or transmission. There are two interrupt sources
from the Serial block, which are obtained by the RI and TI bits in the SCON SFR. These bits are not
automatically cleared by the hardware, and the user will have to clear these bits by software.
All the bits that generate interrupts can be set or reset by software, and thereby software initiated
interrupts can be generated. Each of the individual interrupts can be enabled or disabled by setting or
clearing a bit in the IE SFR. IE also has a global enable/disable bit EA, which can be cleared to
disable all interrupts.
The ADC can generate interrupt after finished ADC converter. There is one interrupt source, which is
obtained by the ADCI bit in the ADCCON SFR. This bit is not automatically cleared by the hardware,
and the user will have to clear this bit using software.
The two comparators can generate interrupt after comparator output has toggle occurs by CMF1 and
CMF2. These bits are not automatically cleared by the hardware, and the user will have to clear these
bits using software.
The I2C function can generate interrupt, if EI2C and EA bits are enabled, when SI Flag is set due to a
new I2C status code is generated, SI flag is generated by hardware and must be cleared by software.
The PWM function can generate interrupt by BKF flag, after external brake pin has brake occurred.
This bit will be cleared by software.
The interrupt flags are sampled every machine cycle. In the same machine cycle, the sampled
interrupts are polled and their priority is resolved. If certain conditions are met then the hardware will
execute an internally generated LCALL instruction which will vector the process to the appropriate
interrupt vector address. The conditions for generating the LCALL are;
1. An interrupt of equal or higher priority is not currently being serviced.
2. The current polling cycle is the last machine cycle of the instruction currently being execute.
3. The current instruction does not involve a write to IE, EIE, IP0, IP0H, IP1 or IPH1 registers and is
not a RETI.
- 65 -
Publication Release Date: February 21, 2008
Revision A9
W79E825A/824A/823B/822B Data Sheet
If any of these conditions are not met, then the LCALL will not be generated. The polling cycle is
repeated every machine cycle, with the interrupts sampled in the same machine cycle. If an interrupt
flag is active in one cycle but not responded to, and is not active when the above conditions are met,
the denied interrupt will not be serviced. This means that active interrupts are not remembered; every
polling cycle is new.
The processor responds to a valid interrupt by executing an LCALL instruction to the appropriate
service routine. This may or may not clear the flag which caused the interrupt. In case of Timer
interrupts, the TF0 or TF1 flags are cleared by hardware whenever the processor vectors to the
appropriate timer service routine. In case of external interrupts, INT0 and INT1 , the flags are cleared
only if they are edge triggered. In case of Serial interrupts, the flags are not cleared by hardware. The
Watchdog timer interrupt flag WDIF has to be cleared by software. The hardware LCALL behaves
exactly like the software LCALL instruction. This instruction saves the Program Counter contents onto
the Stack, but does not save the Program Status Word PSW. The PC is reloaded with the vector
address of that interrupt which caused the LCALL. These address of vector for the different sources
are as follows:
VECTOR LOCATIONS FOR INTERRUPT SOURCES
SOURCE
VECTOR ADDRESS
SOURCE
VECTOR ADDRESS
External Interrupt 0
0003h
Timer 0 Overflow
000Bh
External Interrupt 1
0013h
Timer 1 Overflow
001Bh
Serial Port
0023h
Brownout Interrupt
002Bh
I2C Interrupt
0033h
KBI Interrupt
003Bh
Comparator 2 Interrupt
0043h
-
004Bh
Watchdog Timer
0053h
ADC Interrupt
005Bh
Comparator 1 Interrupt
0063h
-
006Bh
PWM Brake Interrupt
0073h
-
007Bh
Table 12-1: Vector locations for interrupt sources
Execution continues from the vectored address till an RETI instruction is executed. On execution of
the RETI instruction the processor pops the Stack and loads the PC with the contents at the top of the
stack. The user must take care that the status of the stack is restored to what it was after the hardware
LCALL, if the execution is return to the interrupted program. The processor does not notice anything if
the stack contents are modified and will proceed with execution from the address put back into PC.
Note that a RET instruction would perform exactly the same process as a RETI instruction, but it
would not inform the Interrupt Controller that the interrupt service routine is completed, and would
leave the controller still thinking that the service routine is underway.
- 66 -
W79E825A/824A/823B/822B Data Sheet
12.2 Priority Level Structure
The W79E825 series uses a four priority level interrupt structure (highest, high, low and lowest) and
supports up to 13 interrupt sources. The interrupt sources can be individually set to either high or low
levels. Naturally, a higher priority interrupt cannot be interrupted by a lower priority interrupt. However
there exists a pre-defined hierarchy amongst the interrupts themselves. This hierarchy comes into play
when the interrupt controller has to resolve simultaneous requests having the same priority level. This
hierarchy is defined as table below. This allows great flexibility in controlling and handling many
interrupt sources.
PRIORITY BITS
INTERRUPT PRIORITY LEVEL
IPXH
IPX
0
0
Level 0 (lowest priority)
0
1
Level 1
1
0
Level 2
1
1
Level 3 (highest priority)
Table 12-2: Four-level interrupt priority
Each interrupt source can be individually programmed to one of four priority levels by setting or
clearing bits in the IP0, IP0H, IP1, and IP1H registers. An interrupt service routine in progress can be
interrupted by a higher priority interrupt, but not by another interrupt of the same or lower priority. The
highest priority interrupt service cannot be interrupted by any other interrupt source. So, if two
requests of different priority levels are received simultaneously, the request of higher priority level is
serviced.
If requests of the same priority level are received simultaneously, an internal polling sequence
determines which request is serviced. This is called the arbitration ranking. Note that the arbitration
ranking is only used to resolve simultaneous requests of the same priority level.
As below Table summarizes the interrupt sources, flag bits, vector addresses, enable bits, priority bits,
arbitration ranking, and whether each interrupt may wake up the CPU from Power Down mode.
ARBITRATI
ON
RANKING
POWER
DOWN
WAKEUP
1(highest)
Yes
IP0H.5, IP0.5 Software
2
Yes
EWDI (EIE.4)
IP1H.4, IP1.4 Software
3
No
000BH
ET0 (IE.1)
IP0H.1, IP0.1
4
No
SI
0033H
EI2 (EIE.0)
IP1H.0, IP1.0 Software
5
No
ADCI
005BH
EAD (IE.6)
IP0H.6, IP0.6 Hardware
6
Yes(1)
FLAG
VECTOR
ADDRESS
INTERRUPT
ENABLE
BITS
INTERRUPT
FLAG
PRIORITY CLEARED BY
External
Interrupt 0
IE0
0003H
EX0 (IE0.0)
IP0H.0, IP0.0 Follow the
Brownout
Detect
BOF
002BH
EBO (IE.5)
Watchdog
Timer
WDIF
0053H
Timer 0
Interrupt
TF0
I2C Interrupt
ADC Converter
SOURCE
Hardware,
inverse of pin
- 67 -
Hardware,
software
Publication Release Date: February 21, 2008
Revision A9
W79E825A/824A/823B/822B Data Sheet
Continued .
Source
Flag
Vector
address
Interrupt
Enable Bits
Interrupt
Priority
Flag cleared
by
Arbitration
Ranking
Power
Down
Wakeup
7
Yes
Hardware,
External
Interrupt 1
IE1
KBI Interrupt
KBF
003BH
EKB (EIE.1)
IP1H.1, IP1.1 Software
8
Yes
Comparator 1
Interrupt
CMF1
0063H
EC1 (EIE.2)
IP1H.2, IP1.2 Software
9
Yes
Timer 1 Interrupt TF1
001BH
ET1 (IE.3)
IP0H.3, IP0.3
10
No
Comparator 2
Interrupt
CMF2
0043H
EC2 (EIE.3)
IP1H.3, IP1.3 Software
11
Yes
Serial Port Tx
and Rx
TI & RI 0023H
ES (IE.4)
IP0H.4, IP0.4 Software
12
No
PWM Interrupt
BKF
EPWM (EIE.5) IP1H.5, IP1.5 Software
13 (lowest)
No
0013H
EX1 (IE.2)
IP0H.2, IP0.2 Follow the
inverse of pin
0073H
Hardware,
software
Note: 1. The ADC Converter can wake up Power Down Mode when its clock source is from internal RC.
Table 12-3: Vector location for Interrupt sources and power down wakeup
12.3 Response Time
The response time for each interrupt source depends on several factors, such as the nature of the
interrupt and the instruction underway. In the case of external interrupts INT0 and INT1 , they are
sampled at C3 of every machine cycle and then their corresponding interrupt flags IEx will be set or
reset. The Timer 0 and 1 overflow flags are set at C3 of the machine cycle in which overflow has
occurred. These flag values are polled only in the next machine cycle. If a request is active and all
three conditions are met, then the hardware generated LCALL is executed. This LCALL itself takes
four machine cycles to be completed. Thus there is a minimum time of five machine cycles between
the interrupt flag being set and the interrupt service routine being executed.
A longer response time should be anticipated if any of the three conditions are not met. If a higher or
equal priority is being serviced, then the interrupt latency time obviously depends on the nature of the
service routine currently being executed. If the polling cycle is not the last machine cycle of the
instruction being executed, then an additional delay is introduced. The maximum response time (if no
other interrupt is in service) occurs if the W79E825 series are performing a write to IE, EIE, IP0, IP0H,
IP1 or IP1H and then executes a MUL or DIV instruction. From the time an interrupt source is
activated, the longest reaction time is 12 machine cycles. This includes 1 machine cycle to detect the
interrupt, 2 machine cycles to complete the IE, EIE, IP0, IP0H, IP1 or IP1H access, 5 machine cycles
to complete the MUL or DIV instruction and 4 machine cycles to complete the hardware LCALL to the
interrupt vector location.
Thus in a single-interrupt system the interrupt response time will always be more than 5 machine
cycles and not more than 12 machine cycles. The maximum latency of 12 machine cycles is 48 clock
cycles. Note that in the standard 8051 the maximum latency is 8 machine cycles which equals 96
machine cycles. This is a 50% reduction in terms of clock periods.
- 68 -
W79E825A/824A/823B/822B Data Sheet
12.4 Interrupt Inputs
The W79E825 series have 13 interrupts source, and two individual interrupt inputs sources, one is for
IE0, IE1, BOF, KBF, WDT, ADC, CMF1 and CMF2, and other is IF0, IF1, RI+TI ,SI and BKF. Two
interrupt inputs are identical to those present on the standard 80C51 microcontroller as show in below
figures.
If an external interrupt is enabled when the W79E825 series are put into Power Down or Idle mode,
the interrupt will cause the processor to wake up and resume operation.
IE0
EX0
IE1
EX1
BOF
EBO
KBF
EKB
ADCI
EADC
Wakeup
(If in Power Down)
WDT
EWDI
EA
Interrupt
To CPU
CM1
EC1
CM2
EC2
Figure 12-1: Interrupt Sources that can wake up from Power Down Mode
- 69 -
Publication Release Date: February 21, 2008
Revision A9
W79E825A/824A/823B/822B Data Sheet
TF0
ET0
TF1
ET1
RI+TI
Interrupt
To CPU
ES
SI
EA
EI2
BKF
EPWM
Figure 12-2: Interrupt Sources that cannot wake up from Power Down Mode
- 70 -
W79E825A/824A/823B/822B Data Sheet
13 PROGRAMMABLE TIMERS/COUNTERS
The W79E825 series have two 16-bit programmable timer/counters and one programmable Watchdog
Timer. The Watchdog Timer is operationally quite different from the other two timers. It’s
timer/counters have additional timer 0 or timer 1 overflow toggle output enable feature as compare to
conventional timer/counters. This timer overflow toggle output can be configured to automatically
toggle T0 or T1 pin output whenever a timer overflow occurs.
13.1 Timer/Counters 0 & 1
The W79E825 series have two 16-bit Timer/Counters. Each of these Timer/Counters has two 8 bit
registers which form the 16 bit counting register. For Timer/Counter 0 they are TH0, the upper 8 bits
register, and TL0, the lower 8 bit register. Similarly Timer/Counter 1 has two 8 bit registers, TH1 and
TL1. The two can be configured to operate either as timers, counting machine cycles or as counters
counting external inputs.
When configured as a "Timer", the timer counts clock cycles. The timer clock can be programmed to
be thought of as 1/12 of the system clock or 1/4 of the system clock. In the "Counter" mode, the
register is incremented on the falling edge of the external input pin, T0 for Timer 0, and T1 for Timer 1.
The T0 and T1 inputs are sampled in every machine cycle at C4. If the sampled value is high in one
machine cycle and low in the next, then a valid high to low transition on the pin is recognized and the
count register is incremented. Since it takes two machine cycles to recognize a negative transition on
the pin, the maximum rate at which counting will take place is 1/8 of the master clock frequency. In
either the "Timer" or "Counter" mode, the count register will be updated at C3. Therefore, in the
"Timer" mode, the recognized negative transition on pin T0 and T1 can cause the count register value
to be updated only in the machine cycle following the one in which the negative edge was detected.
The "Timer" or "Counter" function is selected by the " C/ T " bit in the TMOD Special Function Register.
Each Timer/Counter has one selection bit for its own; bit 2 of TMOD selects the function for
Timer/Counter 0 and bit 6 of TMOD selects the function for Timer/Counter 1. In addition each
Timer/Counter can be set to operate in any one of four possible modes. The mode selection is done
by bits M0 and M1 in the TMOD SFR.
13.1.1 Time-Base Selection
The W79E825 series can operate like the standard 8051/52 family, counting at the rate of 1/12 of the
clock speed, or in turbo mode, counting at the rate of 1/4 clock speed. The speed is controlled by the
T0M and T1M bits in CKCON, and the default value is zero, which uses the standard 8051/52 speed.
13.1.2 Mode 0
In Mode 0, the timer/counter is a 13-bit counter. The 13-bit counter consists of THx (8 MSB) and the
five lower bits of TLx (5 LSB). The upper three bits of TLx are ignored. The timer/counter is enabled
when TRx is set and either GATE is 0 or INTx is 1. When C / T is 0, the timer/counter counts clock
cycles; when C / T is 1, it counts falling edges on T0 (P1.2 for Timer 0) or T1 (P0.7 for Timer 1). For
clock cycles, the time base may be 1/12 or 1/4 clock speed, and the falling edge of the clock
increments the counter. When the 13-bit value moves from 1FFFh to 0000h, the timer overflow flag
TFx is set, and an interrupt occurs if enabled. This is illustrated in next figure below.
In “Timer” mode, if output toggle enable bit of P2M1.T0OE or P2M1.T1OE is enabled, T0 or T1 output
pin will toggle whenever a timer overflow occurs.
- 71 -
Publication Release Date: February 21, 2008
Revision A9
W79E825A/824A/823B/822B Data Sheet
Figure 13-1: Timer/Counters 0 & 1 in Mode 0
13.1.3 Mode 1
Mode 1 is similar to Mode 0 except that the counting register forms a 16-bit counter, rather than a 13bit counter. This means that all the bits of THx and TLx are used. Roll-over occurs when the timer
moves from a count of FFFFh to 0000h. The timer overflow flag TFx of the relevant timer is set and if
enabled an interrupt will occur. The selection of the time-base in the timer mode is similar to that in
Mode 0. The gate function operates similarly to that in Mode 0.
Figure 13-2: Timer/Counters 0 & 1 in Mode 1
- 72 -
W79E825A/824A/823B/822B Data Sheet
13.1.4 Mode 2
In Mode 2, the timer/counter is in the Auto Reload Mode. In this mode, TLx acts as 8-bit count register,
while THx holds the reload value. When the TLx register overflows from FFh to 00h, the TFx bit in
TCON is set and TLx is reloaded with the contents of THx, and the counting process continues from
here. The reload operation leaves the contents of the THx register unchanged. Counting is enabled by
the TRx bit and proper setting of GATE and INTx pins. As in the other two modes 0 and 1 mode 2
allows counting of either clock cycles (clock/12 or clock/4) or pulses on pin Tn.
In “Timer” mode, if output toggle enable bit of P2M1.T0OE or P2M1.T1OE is enabled, T0 or T1 output
pin will toggle whenever a timer overflow occurs.
Figure 13-3: Timer/Counter 0 & 1 in Mode 2
13.1.5 Mode 3
Mode 3 has different operating methods for the two timer/counters. For timer/counter 1, mode 3 simply
freezes the counter. Timer/Counter 0, however, configures TL0 and TH0 as two separate 8 bit count
registers in this mode. The logic for this mode is shown in the figure. TL0 uses the Timer/Counter 0
control bits C/ T , GATE, TR0, INT0 and TF0. The TL0 can be used to count clock cycles (clock/12 or
clock/4) or 1-to-0 transitions on pin T0 as determined by C/T (TMOD.2). TH0 is forced as a clock cycle
counter (clock/12 or clock/4) and takes over the use of TR1 and TF1 from Timer/Counter 1. Mode 3 is
used in cases where an extra 8 bit timer is needed. With Timer 0 in Mode 3, Timer 1 can still be used
in Modes 0, 1 and 2, but its flexibility is somewhat limited. While its basic functionality is maintained, it
no longer has control over its overflow flag TF1 and the enable bit TR1. Timer 1 can still be used as a
timer/counter and retains the use of GATE and INT1 pin. In this condition it can be turned on and off
by switching it out of and into its own Mode 3. It can also be used as a baud rate generator for the
serial port.
In “Timer” mode, if output toggle enable bit of P2M1.T0OE or P2M1.T1OE is enabled, T0 or T1 output
pin will toggle whenever a timer overflow occurs.
- 73 -
Publication Release Date: February 21, 2008
Revision A9
W79E825A/824A/823B/822B Data Sheet
Figure 13-4: Timer/Counter Mode 3
- 74 -
W79E825A/824A/823B/822B Data Sheet
14 NVM MEMORY
The W79E825 series have NVM data memory of 256/128 bytes for customer’s data store used. The
NVM data memory has four/two pages area and each page has 64 bytes as below figure. The Page
0 address is from FC00h ~ FC3Fh, Page 1 address is from FC40h ~ FC7Fh, Page 2 address is from
FC80h ~ FCBFh, and Page 3 address is from FCC0h ~ FCFFh.
The NVM memory can be read/write by customer program to access. Read NVM data is by MOVC
A,@A+DPTR instruction, and write data is by SFR of NVMADDR, NVMDAT and NVMCON. Before
write data to NVM memory, the page must be erased by providing page address on NVMADDR, which
low byte address of On-Chip Code Memory space will decode, then set EER of NVMCON.7. This will
automatically hold fetch program code and PC Counter, and execute page erase. After finished, this
bit will be cleared by hardware. The erase time is ~ 5ms.
For writing data to NVM memory, user must set address and data to NVMADDR and NVMDAT, then
set EWR of NVMCON.6 to initiate nvm data write. The uC will hold program code and PC Counter,
and then write data to mapping address. Upon write completion, the EWR bit will be cleared by
hardware, the uC will continue execute next instruction. The program time is ~50us.
FFFFH
Page 3
64 bytes
Unused
Code M em ory
FCFFH
FC00H
FBFFH
Page 2
64 bytes
256 Bytes
NVM
Data M em ory
Page 1
64 bytes
Page 0
64 bytes
Unused
Code M em ory
FCFFH
FCC0H
FCBFH
FC80H
FC7FH
FC40H
FC3FH
FC00H
NVM Data M em ory Area
4000H/2000H
3FFFH/1FFFH
16K/8K Bytes
On-C hip
Code M em ory
CO NFIG 2
CO NFIG 1
0000H
O n-Chip Code M em ory Space
Figure 14-1: W79E825/824 Memory Map
- 75 -
Publication Release Date: February 21, 2008
Revision A9
W79E825A/824A/823B/822B Data Sheet
FFFFH
Unused
Code Memory
FC7FH
FC00H
Page 1
64 bytes
128 Bytes
NVM
Data Memory
Unused
Code Memory
Page 0
64 bytes
FC40H
FC3FH
FC00H
NVM Data Memory area
1000H/0800H
0FFFH/07FFH
4K/2K Bytes
On-Chip
Code Memory
CONFIG 2
CONFIG 1
0000H
On-Chip Code Memory Space
Figure 14-2: W79E823/822 Memory Map
- 76 -
FC7FH
W79E825A/824A/823B/822B Data Sheet
15 WATCHDOG TIMER
The Watchdog Timer is a free-running Timer which can be programmed by the user to serve as a
system monitor, a time-base generator or an event timer. It is basically a set of dividers that divide the
system clock. The divider output is selectable and determines the time-out interval. When the time-out
occurs a flag is set, which can cause an interrupt if enabled, and a system reset can also be caused if
it is enabled. The interrupt will occur if the individual interrupt enable and the global enable are set.
The interrupt and reset functions are independent of each other and may be used separately or
together depending on the user’s software.
26-bits Counter
0
Fcpu
WDRUN
(WDCON.7)
16
17
19
20
22
23
25
WDCLR
(Reset Watchdog)
(WDCON.0)
Time-Out
Selector
(WDCON.3)
00
WDIF
01
10
EWDI
(EIE.4)
MUX
Interrupt
(WDCON.2)
WTRF
11
512 clock
delay
WD1,WD0
(WDCON.5/4)
Reset
EWRST
(WDCON.1)
Figure 15-1: Watchdog Timer
The Watchdog Timer should first be restarted by using WDCLR. This ensures that the timer starts
from a known state. The WDCLR bit is used to restart the Watchdog Timer. This bit is self clearing, i.e.
after writing a 1 to this bit the software will automatically clear it. The Watchdog Timer will now count
clock cycles. The time-out interval is selected by the two bits WD1 and WD0 (WDCON.5 and
WDCON.4). When the selected time-out occurs, the Watchdog interrupt flag WDIF (WDCON.3) is set.
After the time-out has occurred, the Watchdog Timer waits for an additional 512 clock cycles. If the
Watchdog Reset EWRST (WDCON.1) is enabled, then 512 clocks after the time-out, if there is no
WDCLR, a system reset due to Watchdog Timer will occur. This will last for two machine cycles, and
the Watchdog Timer reset flag WTRF (WDCON.2) will be set. This indicates to the software that the
Watchdog was the cause of the reset.
When used as a simple timer, the reset and interrupt functions are disabled. The timer will set the
WDIF flag each time the timer completes the selected time interval. The WDIF flag is polled to detect a
time-out and the WDCLR allows software to restart the timer. The Watchdog Timer can also be used
as a very long timer. The interrupt feature is enabled in this case. Every time the time-out occurs an
interrupt will occur if the global interrupt enable EA is set.
The main use of the Watchdog Timer is as a system monitor. This is important in real-time control
applications. In case of some power glitches or electro-magnetic interference, the processor may
begin to execute errant code. If this is left unchecked the entire system may crash. Using the
watchdog timer interrupt during software development will allow the user to select ideal watchdog
reset locations. The code is first written without the watchdog interrupt or reset. Then the Watchdog
interrupt is enabled to identify code locations where interrupt occurs. The user can now insert
instructions to reset the Watchdog Timer, which will allow the code to run without any Watchdog Timer
interrupts. Now the Watchdog Timer reset is enabled and the Watchdog interrupt may be disabled. If
- 77 -
Publication Release Date: February 21, 2008
Revision A9
W79E825A/824A/823B/822B Data Sheet
any errant code is executed now, then the reset Watchdog Timer instructions will not be executed at
the required instants and Watchdog reset will occur.
The Watchdog Timer time-out selection will result in different time-out values depending on the clock
speed. The reset, when enabled, will occur when 512 clocks after time-out has occurred.
WD1
0
0
1
1
WD0
0
217
1
20
0
1
RESET
TIME-OUT
INTERRUPT
TIME-OUT
2
23
2
26
2
217 + 512
20
23
26
2
2
2
NUMBER OF
CLOCKS
TIME
@ 10 MHZ
131072
13.11 mS
+ 512
1048576
104.86 mS
+ 512
8388608
838.86 mS
+ 512
67108864
6710.89 mS
Table 15-2: Time-out values for the Watchdog Timer
The Watchdog Timer will de disabled by a power-on/fail reset. The Watchdog Timer reset does not
disable the Watchdog Timer, but will restart it. In general, software should restart the timer to put it into
a known state. The control bits that support the Watchdog Timer are discussed below.
15.1 WATCHDOG CONTROL
WDIF: WDCON.3 - Watchdog Timer Interrupt flag. This bit is set whenever the time-out occurs in the
Watchdog Timer. If the Watchdog interrupt is enabled (EIE.4), then an interrupt will occur (if the global
interrupt enable is set and other interrupt requirements are met). Software or any reset can clear this
bit.
WTRF: WDCON.2 - Watchdog Timer Reset flag. This bit is set whenever a watchdog reset occurs.
This bit is useful for determined the cause of a reset. Software must read it, and clear it manually. A
Power-fail reset will clear this bit. If EWRST = 0, then this bit will not be affected by the Watchdog
Timer.
EWRST: WDCON.1 - Enable Watchdog Timer Reset. This bit when set to 1 will enable the Watchdog
Timer reset function. Setting this bit to 0 will disable the Watchdog Timer reset function, but will leave
the timer running.
WDCLR: WDCON.0 - Reset Watchdog Timer. This bit is used to clear the Watchdog Timer and to
restart it. This bit is self-clearing, so after the software writes 1 to it the hardware will automatically
clear it. If the Watchdog Timer reset is enabled, then the WDCLR has to be set by the user within 512
clocks of the time-out. If this is not done then a Watchdog Timer reset will occur.
- 78 -
W79E825A/824A/823B/822B Data Sheet
15.2 CLOCK CONTROL of Watchdog
WD1, WD0: WDCON.5, WDCON.4 - Watchdog Timer Mode select bits. These two bits select the
time-out interval for the watchdog timer. The reset time is 512 clocks longer than the interrupt time-out
value.
The default Watchdog time-out is 217 clocks, which is the shortest time-out period. The WDRUN, WD0,
WD1, EWRST, WDIF and WDCLR bits are protected by the Timed Access procedure. This prevents
software from accidentally enabling or disabling the watchdog timer. More importantly, it makes it
highly improbable that errant code can enable or disable the Watchdog Timer.
- 79 -
Publication Release Date: February 21, 2008
Revision A9
W79E825A/824A/823B/822B Data Sheet
16 SERIAL PORT (UART)
Serial port in the W79E825 series is a full duplex port. The W79E825 series provide the user with
additional features such as the Frame Error Detection and the Automatic Address Recognition. The
serial ports are capable of synchronous as well as asynchronous communication. In Synchronous
mode the W79E825 series generate the clock and operates in a half duplex mode. In the
asynchronous mode, full duplex operation is available. This means that it can simultaneously transmit
and receive data. The transmit register and the receive buffer are both addressed as SBUF Special
Function Register. However any write to SBUF will be to the transmit register, while a read from SBUF
will be from the receiver buffer register. The serial port can operate in four different modes as
described below.
16.1 MODE 0
This mode provides synchronous communication with external devices. In this mode serial data is
transmitted and received on the RXD line. TXD is used to transmit the shift clock. The TxD clock is
provided by the W79E825 series whether the device is transmitting or receiving. This mode is
therefore a half duplex mode of serial communication. In this mode, 8 bits are transmitted or received
per frame. The LSB is Transmitted/Received first. The baud rate is fixed at 1/12 or 1/4 of the oscillator
frequency. This Baud Rate is determined by the SM2 bit (SCON.5). When this bit is set to 0, then the
serial port runs at 1/12 of the clock. When set to 1, the serial port runs at 1/4 of the clock. This
additional facility of programmable baud rate in mode 0 is the only difference between the standard
8051 and the W79E825 series.
The functional block diagram is shown below. Data enters and leaves the Serial port on the RxD line.
The TxD line is used to output the shift clock. The shift clock is used to shift data into and out of the
W79E825 series and the device at the other end of the line. Any instruction that causes a write to
SBUF will start the transmission. The shift clock will be activated and data will be shifted out on the
RxD pin till all 8 bits are transmitted. If SM2 = 1, then the data on RxD will appear 1 clock period
before the falling edge of shift clock on TxD. The clock on TxD then remains low for 2 clock periods,
and then goes high again. If SM2 = 0, the data on RxD will appear 3 clock periods before the falling
edge of shift clock on TxD. The clock on TxD then remains low for 6 clock periods, and then goes high
again. This ensures that at the receiving end the data on RxD line can either be clocked on the rising
edge of the shift clock on TxD or latched when the TxD clock is low.
- 80 -
W79E825A/824A/823B/822B Data Sheet
Transmit Shift Register
Write to
SBUF
Fcpu
Internal
Data Bus
PARIN
LOAD
SOUT
CLOCK
1/12
SM2 0
1/4
1
TX START
TX SHIFT
TX CLOCK
TI
RXD
P1.1 Alternate
Output Function
Serial Interrupt
RI
RX CLOCK
TXD
P1.0 Alternate
Output Function
SHIFT CLOCK
RI
REN
RX START
LOAD SBUF
RX SHIFT
Serial Controllor
RXD
P1.1 Alternate
Input Function
Read SBUF
CLOCK
SIN
PAROUT
SBUF
Internal
Data Bus
Figure 16-1: Serial Port Mode 0
The TI flag is set high in C1 following the end of transmission of the last bit. The serial port will receive
data when REN is 1 and RI is zero. The shift clock (TxD) will be activated and the serial port will latch
data on the rising edge of shift clock. The external device should therefore present data on the falling
edge on the shift clock. This process continues till all the 8 bits have been received. The RI flag is set
in C1 following the last rising edge of the shift clock on TxD. This will stop reception, till the RI is
cleared by software.
16.2 MODE 1
In Mode 1, the full duplex asynchronous mode is used. Serial communication frames are made up of
10 bits transmitted on TXD and received on RXD. The 10 bits consist of a start bit (0), 8 data bits (LSB
first), and a stop bit (1). On received, the stop bit goes into RB8 in the SFR SCON. The baud rate in
this mode is variable. The serial baud can be programmed to be 1/16 or 1/32 of the Timer 1 overflow.
Since the Timer 1 can be set to different reload values, a wide variation in baud rates is possible.
Transmission begins with a write to SBUF. The serial data is brought out on to TxD pin at C1 following
the first roll-over of divide by 16 counter. The next bit is placed on TxD pin at C1 following the next
rollover of the divide-by-16 counter. Thus the transmission is synchronized to the divide-by-16 counter
and not directly to the write to SBUF signal. After all 8 bits of data are transmitted, the stop bit is
transmitted. The TI flag is set in the C1 state after the stop bit has been put out on TxD pin. This will
be at the 10th rollover of the divide-by-16 counter after a write to SBUF.
- 81 -
Publication Release Date: February 21, 2008
Revision A9
W79E825A/824A/823B/822B Data Sheet
Reception is enabled only if REN is high. The serial port actually starts the receiving of serial data,
with the detection of a falling edge on the RxD pin. The 1-to-0 detector continuously monitors the RxD
line, sampling it at the rate of 16 times the selected baud rate. When a falling edge is detected, the
divide–by-16 counter is immediately reset. This helps to align the bit boundaries with the rollovers of
the divide-by-16 counter.
The 16 states of the counter effectively divide the bit time into 16 slices. The bit detection is done on a
best of three bases. The bit detector samples the RxD pin, at the 8th, 9th and 10th counter states. By
using a majority 2 of 3 voting system, the bit value is selected. This is done to improve the noise
rejection feature of the serial port. If the first bit detected after the falling edge of RxD pin is not 0, then
this indicates an invalid start bit, and the reception is immediately aborted. The serial port again looks
for a falling edge in the RxD line. If a valid start bit is detected, then the rest of the bits are also
detected and shifted into the SBUF.
After shifting in 8 data bits, there is one more shift to do, after which the SBUF and RB8 are loaded
and RI is set. However certain conditions must be met before the loading and setting of RI can be
done.
1. RI must be 0 and
2. Either SM2 = 0, or the received stop bit = 1.
If these conditions are met, then the stop bit goes to RB8, the 8 data bits go into SBUF and RI is set.
Otherwise the received frame may be lost. After the middle of the stop bit, the receiver goes back to
looking for a 1-to-0 transition on the RxD pin.
Figure 16-2: Serial Port Mode 1
- 82 -
W79E825A/824A/823B/822B Data Sheet
16.3 MODE 2
This mode uses a total of 11 bits in asynchronous full-duplex communication. The functional
description is shown in the figure below. The frame consists of one start bit (0), 8 data bits (LSB first),
a programmable 9th bit (TB8) and a stop bit (0). The 9th bit received is put into RB8. The baud rate is
programmable to 1/32 or 1/64 of the oscillator frequency, which is determined by the SMOD bit in
PCON SFR. Transmission begins with a write to SBUF. The serial data is brought out on to TxD pin at
C1 following the first roll-over of the divide-by-16 counter. The next bit is placed on TxD pin at C1
following the next rollover of the divide-by-16 counter. Thus the transmission is synchronized to the
divide-by-16 counter, and not directly to the write to SBUF signal. After all 9 bits of data are
transmitted, the stop bit is transmitted. The TI flag is set in the C1 state after the stop bit has been put
out on TxD pin. This will be at the 11th rollover of the divide-by-16 counter after a write to SBUF.
Reception is enabled only if REN is high. The serial port actually starts the receiving of serial data,
with the detection of a falling edge on the RxD pin. The 1-to-0 detector continuously monitors the RxD
line, sampling it at the rate of 16 times the selected baud rate. When a falling edge is detected, the
divide- by-16 counter is immediately reset. This helps to align the bit boundaries with the rollovers of
the divide-by-16 counter. The 16 states of the counter effectively divide the bit time into 16 slices. The
bit detection is done on a best of three bases. The bit detector samples the RxD pin, at the 8th, 9th
and 10th counter states. By using a majority 2 of 3 voting system, the bit value is selected. This is
done to improve the noise rejection feature of the serial port.
Figure 16-3: Serial Port Mode 2
- 83 -
Publication Release Date: February 21, 2008
Revision A9
W79E825A/824A/823B/822B Data Sheet
If the first bit detected after the falling edge of RxD pin, is not 0, then this indicates an invalid start bit,
and the reception is immediately aborted. The serial port again looks for a falling edge in the RxD line.
If a valid start bit is detected, then the rest of the bits are also detected and shifted into the SBUF.
After shifting in 9 data bits, there is one more shift to do, after which the SBUF and RB8 are loaded
and RI is set. However certain conditions must be met before the loading and setting of RI can be
done.
1. RI must be 0 and
2. Either SM2 = 0, or the received stop bit = 1.
If these conditions are met, then the stop bit goes to RB8, the 8 data bits go into SBUF and RI is set.
Otherwise the received frame may be lost. After the middle of the stop bit, the receiver goes back to
looking for a 1-to-0 transition on the RxD pin.
16.4 MODE 3
This mode is similar to Mode 2 in all aspects, except that the baud rate is programmable. The user
must first initialize the Serial related SFR SCON before any communication can take place. This
involves selection of the Mode and baud rate. The Timer 1 should also be initialized if modes 1 and 3
are used. In all four modes, transmission is started by any instruction that uses SBUF as a destination
register. Reception is initiated in Mode 0 by the condition RI = 0 and REN = 1. This will generate a
clock on the TxD pin and shift in 8 bits on the RxD pin. Reception is initiated in the other modes by the
incoming start bit if REN = 1. The external device will start the communication by transmitting the start
bit.
Figure 16-4: Serial Port Mode 3
- 84 -
W79E825A/824A/823B/822B Data Sheet
TYPE
BAUD CLOCK
FRAME
SIZE
START
BIT
STOP
BIT
9TH BIT
FUNCTION
0
Synch.
4 or 12 TCLKS
8 bits
No
No
None
1
1
Asynch.
Timer 1
10 bits
1
1
None
1
0
2
Asynch.
32 or 64 TCLKS
11 bits
1
1
0, 1
1
1
3
Asynch.
Timer 1
11 bits
1
1
0, 1
SM0
SM1
MODE
0
0
0
Table 16-5: Serial Port Mode Summary Table
16.5 Framing Error Detection
A Frame Error occurs when a valid stop bit is not detected. This could indicate incorrect serial data
communication. Typically the frame error is due to noise and contention on the serial communication
line. The W79E825 series have the facility to detect such framing errors and set a flag which can be
checked by software.
The Frame Error FE bit is located in SCON.7. This bit is normally used as SM0 in the standard 8051
family. However, in the W79E825 series it serves a dual function and is called SM0/FE. There are
actually two separate flags, one for SM0 and the other for FE. The flag that is actually accessed as
SCON.7 is determined by SMOD0 (PCON.6) bit. When SMOD0 is set to 1, then the FE flag is
indicated in SM0/FE. When SMOD0 is set to 0, then the SM0 flag is indicated in SM0/FE.
The FE bit is set to 1 by hardware but must be cleared by software. Note that SMOD0 must be 1 while
reading or writing to FE. If FE is set, then any following frames received without any error will not clear
the FE flag. The clearing has to be done by software.
16.6 Multiprocessor Communications
Multiprocessor communications makes use of the 9th data bit in modes 2 and 3. In the W79E825
series, the RI flag is set only if the received byte corresponds to the Given or Broadcast address. This
hardware feature eliminates the software overhead required in checking every received address, and
greatly simplifies the software programmer task.
In the multiprocessor communication mode, the address bytes are distinguished from the data bytes
by transmitting the address with the 9th bit set high. When the master processor wants to transmit a
block of data to one of the slaves, it first sends out the address of the targeted slave (or slaves). All the
slave processors should have their SM2 bit set high when waiting for an address byte. This ensures
that they will be interrupted only by the reception of an address byte. The Automatic address
recognition feature ensures that only the addressed slave will be interrupted. The address comparison
is done in hardware not software.
The addressed slave clears the SM2 bit, thereby clearing the way to receive data bytes. With SM2 = 0,
the slave will be interrupted on the reception of every single complete frame of data. The unaddressed
slaves will be unaffected, as they will be still waiting for their address. In Mode 1, the 9th bit is the stop
bit, which is 1 in case of a valid frame. If SM2 is 1, then RI is set only if a valid frame is received and
the received byte matches the Given or Broadcast address.
- 85 -
Publication Release Date: February 21, 2008
Revision A9
W79E825A/824A/823B/822B Data Sheet
The Master processor can selectively communicate with groups of slaves by using the Given Address.
All the slaves can be addressed together using the Broadcast Address. The addresses for each slave
are defined by the SADDR and SADEN SFRs. The slave address is an 8-bit value specified in the
SADDR SFR. The SADEN SFR is actually a mask for the byte value in SADDR. If a bit position in
SADEN is 0, then the corresponding bit position in SADDR is don't care. Only those bit positions in
SADDR whose corresponding bits in SADEN are 1 are used to obtain the Given Address. This gives
the user flexibility to address multiple slaves without changing the slave address in SADDR.
The following example shows how the user can define the Given Address to address different slaves.
Slave 1:
SADDR 1010 0100
SADEN 1111 1010
Given 1010 0x0x
Slave 2:
SADDR 1010 0111
SADEN 1111 1001
Given 1010 0xx1
The Given address for slave 1 and 2 differ in the LSB. For slave 1, it is a don't care, while for slave 2 it
is 1. Thus to communicate only with slave 1, the master must send an address with LSB = 0 (1010
0000). Similarly the bit 1 position is 0 for slave 1 and don't care for slave 2. Hence to communicate
only with slave 2 the master has to transmit an address with bit 1 = 1 (1010 0011). If the master
wishes to communicate with both slaves simultaneously, then the address must have bit 0 = 1 and bit
1 = 0. The bit 3 position is don't care for both the slaves. This allows two different addresses to select
both slaves (1010 0001 and 1010 0101).
The master can communicate with all the slaves simultaneously with the Broadcast Address. This
address is formed from the logical OR of the SADDR and SADEN SFRs. The zeros in the result are
defined as don't cares. In most cases the Broadcast Address is FFh. In the previous case, the
Broadcast Address is (1111111x) for slave 1 and (11111111) for slave 2.
The SADDR and SADEN SFRs are located at address A9h and B9h respectively. On reset, these two
SFRs are initialized to 00h. This results in Given Address and Broadcast Address being set as xxxx
xxxx (i.e. all bits don't care). This effectively removes the multiprocessor communications feature,
since any selectivity is disabled.
- 86 -
W79E825A/824A/823B/822B Data Sheet
17 TIME ACCESS PROCTECTION
The W79E825 series have a new feature, like the Watchdog Timer which is a crucial to proper
operation of the system. If left unprotected, errant code may write to the Watchdog control bits
resulting in incorrect operation and loss of control. In order to prevent this, the W79E825 series have a
protection scheme which controls the write access to critical bits. This protection scheme is done
using a timed access.
In this method, the bits which are to be protected have a timed write enable window. A write is
successful only if this window is active, otherwise the write will be discarded. This write enable window
is open for 3 machine cycles if certain conditions are met. After 3 machine cycles, this window
automatically closes. The window is opened by writing AAh and immediately 55h to the Timed Access
(TA) SFR. This SFR is located at address C7h. The suggested code for opening the timed access
window is
TA
REG 0C7h
;Define new register TA, located at 0C7h
MOV TA, #0AAh
MOV TA, #055h
When the software writes AAh to the TA SFR, a counter is started. This counter waits for 3 machine
cycles looking for a write of 55h to TA. If the second write (55h) occurs within 3 machine cycles of the
first write (AAh), then the timed access window is opened. It remains open for 3 machine cycles,
during which the user may write to the protected bits. Once the window closes the procedure must be
repeated to access the other protected bits.
Examples of Timed Assessing are shown below.
Example 1: Valid access
MOV
TA, #0AAh
MOV
TA, #055h
MOV
WDCON, #00h
Example 2: Valid access
MOV
TA, #0AAh
MOV
TA, #055h
NOP
SETB
EWRST
Example 3: Valid access
MOV
TA, #0AAh
MOV
TA, #055h
ORL
WDCON, #00000010B
Example 4: Invalid access
MOV
TA, #0AAh
MOV
TA, #055h
NOP
NOP
CLR
EWT
;3 M/C Note: M/C = Machine Cycles
;3 M/C
;3 M/C
;3 M/C
;3 M/C
;1 M/C
;2 M/C
;3 M/C
;3 M/C
;3M/C
;3 M/C
;3 M/C
;1 M/C
;1 M/C
;2 M/C
- 87 -
Publication Release Date: February 21, 2008
Revision A9
W79E825A/824A/823B/822B Data Sheet
Example 5: Invalid Access
MOV
TA, #0AAh
NOP
MOV
TA, #055h
SETB
EWT
;3 M/C
;1 M/C
;3 M/C
;2 M/C
In the first three examples, the writing to the protected bits is done before the 3 machine cycles
window closes. In Example 4, however, the writing to the protected bit occurs after the window has
closed, and so there is effectively no change in the status of the protected bit. In Example 5, the
second write to TA occurs 4 machine cycles after the first write, therefore the timed access window is
not opened at all, and the write to the protected bit fails.
- 88 -
W79E825A/824A/823B/822B Data Sheet
18 KEYBOARD INTERRUPT (KBI)
The W79E825 series are provided 8 keyboard interrupt function to detect keypad status which key is
acted, and allow a single interrupt to be generated when any key is pressed on a keyboard or keypad
connected to specific pins of the W79E825 series, as shown below Figure. This interrupt may be used
to wake up the CPU from Idle or Power Down modes, after chip is in Power Down or Idle Mode.
Keyboard function is supported through by Port 0. It can allow any or all pins of Port 0 to be enabled to
cause this interrupt. Port pins are enabled by the setting of bits of KBI0 ~ KBI7 in the KBI register, as
shown below Figure. The Keyboard Interrupt Flag (KBF) in the AUXR1 register is set when any
enabled pin is pulled low while the KBI interrupt function is active, and the low pulse must be more
than 1 machine cycle, an interrupt will be generated if it has been enabled. The KBF bit set by
hardware and must be cleared by software. In order to determine which key was pressed, the KBI will
allow the interrupt service routine to poll port 0.
P0.7
KBI.7
P0.6
KBI.6
P0.5
KBI.5
P0.4
KBI.4
P0.3
KBI.3
KBF (KBI Interrupt)
EKB
(From EIE Register)
P0.2
KBI.2
P0.1
KBI.1
P0.0
KBI.0
Figure 18-1: Keyboard Interrupt
- 89 -
Publication Release Date: February 21, 2008
Revision A9
W79E825A/824A/823B/822B Data Sheet
19 ANALOG COMPARATORS
The W79E825 series are provided two Comparators. Input and output options allow use of the
comparators in a number of different Configurations. The Comparator output is a logical one when its
positive input is greater than its negative input, otherwise the output is a zero. Each Comparator can
be configured to cause to an interrupt when the output value change. The block diagram is as below.
Each Comparator has a control register (CMP1 and CMP2), Both Inputs are CINnA, CINnB, CMPREF
and internal reference voltage, and outputs are CMP1 and CMP2 by setting OEn bit. After enable
Comparators the Comparator need waited stable time to guarantee Comparator output. If programmer
used internal reference voltage, it will be set OEn bit to “1”. The value of internal reference voltage
(Vref) is 1.19V +/- 10%.
CP1
(P0.4) CIN1A
+
(P0.3) CIN1B
(P0.5) CMPREF
Enable CMP1
CE1
CE2
CMP1 Analog Circuit
Comparator1
En
CMP1(P0.6)
-
Vref
Vref
CO1
OE1
Change Detect
CN1
CP2
Enable CMP2
(P0.2) CIN2A
CMF1
CMP2 Analog Circuit
Comparator2
+
(P0.1) CIN2B
Interrupt
CO2
CMP2(P0.0)
-
OE2
Change Detect
CN2
CMF2
Figure 19-1: Analog Comparators
- 90 -
Interrupt
W79E825A/824A/823B/822B Data Sheet
20 I/O PORT CONFIGURATION
The W79E825 series have three I/O ports, port 0, port 1 and port 2. All pins of I/O ports can be
configured to one of four types by software except P1.5 is only input pin. When P1.5 is configured
reset pin by RPD=0 in the CONFIG 1 register, the W79E825 series can support 15 pins by use
Crystal. If used on-chip RC oscillator the P1.5 is configured input pin, the W79E825 series can be
supported up to 18 pins. The I/O ports configuration setting as below table.
PXM1.Y
PXM2.Y
PORT INPUT/OUTPUT MODE
0
0
Quasi-bidirectional
0
1
Push-Pull
1
0
Input Only (High Impedance)
P2M1.PxS=0, TTL input
P2M1.PxS=1, Schmitt input
1
1
Open Drain
Table 20-1: I/O port Configuration Table
All port pins can be determined to high or low after reset by configure PRHI bit in the CONFIG1
register. After reset, these pins are in quasi-bidirectional mode. The port pin of P1.5 only is a Schmitt
trigger input.
Enabled toggle outputs from Timer 0 and Timer 1 by T0OE and T1OE on P2M1 register, the output
frequency of Timer 0 or Timer 1 is by Timer overflow.
Each I/O port of the W79E825 series may be selected to use TTL level inputs or Schmitt inputs by
P(n)S bit on P2M1 register, where n is 0, 1 or 2. When P(n)S is set to 1, Ports are selected Schmitt
trigger inputs on Port(n). The P2.0 (XTAL2) can be configured clock output when used on-chip RC or
external Oscillator is clock source, and the frequency of clock output is divided by 4 on on-chip RC
clock or external Oscillator.
20.1 Quasi-Bidirectional Output Configuration
After chip was power on or reset, the all ports output are this mode, and output is common with the
8051. This mode can be used as both an input and output without the need to reconfigure the port.
When the pin is pulled low, it is driven strongly and able to sink a fairly large current. These features
are somewhat similar to an open drain output except that there are three pull-up transistors in the
quasi-bidirectional output that serve different purposes.
This mode has three pull-up resisters that are “strong” pull-up, “weak” pull-up and “very weak” pull-up.
The “strong” pull-up is used fast transition from logic “0” change to logic “1”, and it is fast latch and
transition. When port pins is occur from logic “0” to logic “1”, the strong pull-up will quickly turn on two
CPU clocks to pull high then turn off.
- 91 -
Publication Release Date: February 21, 2008
Revision A9
W79E825A/824A/823B/822B Data Sheet
The “weak” pull-up is turned on when the input port pin is logic “1” level or itself is logic “1”, and it
provides the most source current for a quasi-bidirectional pin that output is “1” or port latch is logic “0”’.
The “very weak” pull-up is turned on when the port latch is logic “1”. If port latch is logic “0”, it will be
turned off. The very weak pull-up is support a very small current that will pull the pin high if it is left
floating. And the quasi-bidirectional port configuration is shown as below figure.
If port pin is low, it can drives large sink current for output, and it is similar with push-pull and open
drain on sink current output.
VDD
2 CPU
Clock Delay
P
Strong
P
Very
Weak
P
Weak
Port Pin
Port Latch
Data
N
Input Data
Figure 20-2: Quasi-Bidirectional Output
20.2 Open Drain Output Configuration
To configure this mode is turned off all pull-ups. If used similar as a logic output, the port must has an
external pull-up resister. The open drain port configuration is shown as below.
Port Pin
Port Latch
Data
N
Input Data
Figure 20-3: Open Drain Output
- 92 -
W79E825A/824A/823B/822B Data Sheet
20.3 Push-Pull Output Configuration
The push-pull output mode has two strong pull-up and pull-down structure that support large source
and sink current output. It removes “weak” pull-up and “very weak” pull-up resister and remain “strong
pull-up resister on quasi-bidirectional output mode. The “strong” pull-up is always turns on when port
latch is logic “1” to support source current. The push-pull port configuration is shown in below Figure.
The W79E825 series have three port pins that can’t be configured. They are P1.2, P1.3, and P1.5.
The port pins P1.2 and P1.3 are configured to open drain outputs. They may be used as inputs by
writing ones to their respective port latches.
VDD
P
Port Pin
Port Latch
Data
N
Input Data
Figure 20-4: Push-Pull Output
20.4 Input Only Configuration
By configure this mode, the ports are only digital input and disable digital output. The W79E825 series
can select input pin to Schmitt trigger or TTL level input by PxM1.y and PxM2.y registers.
- 93 -
Publication Release Date: February 21, 2008
Revision A9
W79E825A/824A/823B/822B Data Sheet
21 OSCILLATOR
The W79E825 series provides three oscillator input option. These are configured at CONFIG register
(CONFIG1) that include On-Chip RC Oscillator Option, External Clock Input Option and Crystal
Oscillator Input Option. The Crystal Oscillator Input frequency may be supported from 4MHz to
20MHz, and without capacitor or resistor.
Figure 21-1: Oscillator
21.1 On-Chip RC Oscillator Option
The On-Chip RC Oscillator is fixed at 6MHz +/- 25% frequency to support clock source. When FOSC1,
FOSC0 = 01b, the On-Chip RC Oscillator is enabled. A clock output on P2.0 (XTAL2) may be enabled
when On-Chip RC oscillator is used.
- 94 -
W79E825A/824A/823B/822B Data Sheet
21.2 External Clock Input Option
The clock source pin (XTAL1) is from External Clock Input by FOSC1, FOSC0 = 11H, and frequency
range is form 0Hz up to 20MHz. A clock output on P2.0 (XTAL2) may be enabled when External Clock
Input is used.
The W79E825 series supports a clock output function when either the on-chip RC oscillator or the
external clock input options is selected. This allows external devices to synchronize to the W79E825
serial. When enabled, via the ENCLK bit in the P2M1 register, the clock output appears on the
XTAL2/CLKOUT pin whenever the on-chip oscillator is running, including in Idle Mode. The frequency
of the clock output is 1/4 of the CPU clock rate. If the clock output is not needed in Idle Mode, it may
be turned off prior to entering Idle mode, saving additional power. The clock output may also be
enabled when the external clock input option is selected.
21.3 CPU Clock Rate select
The CPU clock of W79E825 series may be selected by the DIVM register. If DIVM = 00H, the CPU
clock is running at 4 CPU clock per machine cycle, and without any division from source clock
(Fosc). When the DIVM register is set to N value, the CPU clock is divided by 2(DVIM+1), so
CPU clock frequency division is from 4 to 512. The user may use this feature to set CPU at a
lower speed rate for reducing power consumption. This is very similar to the situation when
CPU has entered Idle mode. In addition this frequency division function affect all peripheral
timings as they are all sourcing from the CPU clock(Fcpu).
- 95 -
Publication Release Date: February 21, 2008
Revision A9
W79E825A/824A/823B/822B Data Sheet
22 POWER MONITORING FUNCTION
Power-On Detect and Brownout are two additional power monitoring functions implemented in
W79E825 series to prevent incorrect operation during power up and power drop or loss.
22.1 Power On Detect
The Power–On Detect function is a designed to detect power up after power voltage reaches to a level
where Brownout Detect can work. After power on detect, the POR (PCON.4) will be set to “1” to
indicate an initial power up condition. The POR flag will be cleared by software.
22.2 Brownout Detect
The Brownout Detect function is detect power voltage is drops to brownout voltage level, and allows
preventing some process work or indicate power warming. The W79E825 series have two brownout
voltage levels to select by BOV (CONFIG1.4). If BOV =0 that brownout voltage level is 3.8V, If BOV =
1 that brownout voltage level is 2.5V. When the Brownout voltage is drop to select level, the brownout
detector will detect and keeps this active until VDD is returns to above brownout Detect voltage. The
Brownout Detect block is as follow.
Brownout
Detect
Circuit
0
To Reset
1
To Brownout interrupt
BOF
BOD
(Enable Brownout Detect)
BOI
Figure 22-1: Brownout Detect Block
When Brownout Detect is enabled by BOD (AUXR1.6), the BOF (PCON.5) flag will be set and
brownout reset will occur. If BOI (AUXR1.5) is set to “1”, the brownout detect will cause interrupt via
the EA (IE.7) and EBO (IE.5) bits is set. BOF is cleared by software.
In order to guarantee a correct detection of Brownout, The VDD fall time must be slower than
50mV/us, and rise time is slower than 2mV/us to ensure a proper reset.
- 96 -
W79E825A/824A/823B/822B Data Sheet
23 PULSE-WIDTH-MODULATED (PWM) OUTPUTS
The W79E825 series have four Pulse Width Modulated (PWM) channels, and the PWM outputs are
PWM0 (P0.1), PWM1 (P1.6), PWM2 (P1.7) and PWM3 (P0.0). The initial PWM outputs level
correspondingly depend on the PRHI level set prior to the chip reset. When PRHI set to high, PWM
output will initialize to high after chip reset; if PRHI set to low, PWM output will be initialize to low after
chip reset.
The W79E825 series support 10-bits down counter with cpu clock as its input. The PWM counter
clock, has the same frequency as the clock source FCPU = FOSC. When the counter reaches underflow
it will automatic reloaded from counter register. The PWM frequency is given by: fPWM = FCPU /
(PWMP+1), where PWMP is 10-bits register of PWMPH.1, PWMPH.0 and PWMPL.7~PWMPL.0.
The counter register will be loaded with the PWMP register value when PWMRUN, load and CF are
equal to 1; the load bit will be automatically cleared to zero on the next clock cycle, and at the same
time the counter register value will be loaded to the 10 bits down counter. CF flag is 10-bits down
counter reaches underflow, the CF flag will be cleared by software.
The pulse width of each PWM output is determined by the Compare registers of PWM0L through
PWM3L and PWM0H through PWM3H. When PWM compare register is greater than 10-bits counter
register, the PWM output is low. Load bit has to be set to 1 for alteration of PWMn width. After the
new values are written to the PWMn registers, and if load bit is set to 1, the new PWMn values will be
loaded to the PWMn registers upon the next underflow. The PWM output high pulses width is given
by:
tHI = (PWMP – PWMn+1). Notice, if compare register is set to 000H, the PWMn output will stay at high,
and if compare register is set to 3FFH, the PWMn output will stuck at low until there is a change in the
compare register.
- 97 -
Publication Release Date: February 21, 2008
Revision A9
W79E825A/824A/823B/822B Data Sheet
Brake Flag
BKF
BKCH
PWMP Register
load
BPEN
Counter Register
Brake
Control
Block
0
P0.2=0
1
P0.2=1
Enable External Brake Pin
(BPEN,BKCH) = (1,0)
Brake Pin
(P0.2)
BKPS
BKEN
CF
PWMRUN
FCPU
10-bits Counter
CLRPWM
Clear
Counter
X
Y
PWM0I
+
+
0
>
PWM0
-PWM0B
Compare Register
PWM0 Register
X
Y
Y
0
>
PWM1
-
P1.7
0
>
PWM2
PWM2B
X
Y
P0.0
0
>
PWM3
PWM3B
Compare Register
1
PWM3 Register
Figure 23-1: W79E825/824/823/822 PWM Block Diagram
- 98 -
PIN 2
(P1.7)
1
PWM3I
+
PIN 3
(P1.6)
1
PWM2I
+
Compare Register
PWM2 Register
P1.6
PWM1B
X
PIN 20
(P0.1)
1
PWM1I
+
Compare Register
PWM1 Register
P0.1
PIN 1
(P0.0)
W79E825A/824A/823B/822B Data Sheet
The W79E825 series devices support brake function which can be activated by software or external
pin (P0.2). The Brake function is controlled by the PWMCON2 register. The setting and details
description of software brake and external pin brake can be found at the brake condition table at the
SFR section.
As for external brake, the user program can poll the brake flag (BKF) or enable PWM’s brake interrupt
to determine when the external Brake Pin is asserted and causes a brake to occur. The brake pin
(P0.2) can be set to trigger the brake function by either low or high level, by clearing or setting the
PWMCON2.6 (BKPS) bit respectively. The details description of varies brake functions can be found
in the brake condition table.
Since the Brake Pin being asserted will automatically clear the Run bit of PWMCON1.7 and BKF
(PWMCON3.0) flag will be set, the user program can poll this bit or enable PWM’s brake interrupt to
determine when the Brake Pin causes a brake to occur. The other method for detecting a brake
caused by the Brake Pin would be to tie the Brake Pin to one of the external interrupt pins. This latter
approach is needed if the Brake signal is of insufficient length to ensure that it can be captured by a
polling routine. When, after being asserted, the condition causing the brake is removed, the PWM
outputs go to whatever state that had immediately prior to the brake. This means that in order to go
from brake being asserted to having the PWM run without going through an indeterminate state, care
must be taken. If the Brake Pin causes brake to be asserted, the following prototype code will allow
the PWM to go from brake and then run smoothly after brake is released.
- 99 -
Publication Release Date: February 21, 2008
Revision A9
W79E825A/824A/823B/822B Data Sheet
Start
1. Clear 10-bit PWM counter
CLRPWM=1
2. Reload PWMP & PWM registers
3. Enable brake function
(BKEN,BPEN,BKCH)=(1,1,0)
Initialize PWM function
1. Set PWM Control Regs
2. Set PWM brake output pattern(PWMnB)
3. Enable brake function
(BKEN,BPEN,BKCH)=(1,1,0)
PWM starts running
Brake occurs?
Brake pin is
asserted?
Yes
No
No
1. Clear BKF
PWM output=PWM comparator output
2. Re-start PWM Running by setting
PWMRUN=1; load bit=1
Yes
1. PWMn output=PWMnB
2. H/W set BKF=1 & PWMRUN=0
3. S/W switch to S/W Brake
(BKEN,BPEN,BKCH)=(1,0,0)
4. Set PWMn comparator output =
PWMnB or a given pattern
End
Figure 23-2: PWM Brake Function
- 100 -
W79E825A/824A/823B/822B Data Sheet
24 ANALOG-TO-DIGITAL CONVERTER
The ADC contains a DAC which converts the contents of a successive approximation register to a
voltage (VDAC) which is compared to the analog input voltage (Vin). The output of the comparator is
fed to the successive approximation control logic which controls the successive approximation
register. A conversion is initiated by setting ADCS in the ADCCON register. There are two triggering
methods by ADC to start conversion, either by purely software start or external pin STADC triggering.
The software start mode is used to trigger ADC conversion regardless of ADCCON.5 (ADCEX) bit is
set or cleared. A conversion will start simply by setting the ADCCON.3 (ADCS) bit. As for the
external STADC pin triggering mode, ADCCON.5 (ADCEX) bit has to be set and a rise edge pulse has
to apply to STADC pin to trigger the ADC conversion. For the rising edge triggering method, a
minimum of at least 2 machine cycles symmetrical pulse is required.
The low-to-high transition of STADC is recognized at the end of a machine cycle, and the conversion
commences at the beginning of the next cycle. When a conversion is initiated by software, the
conversion starts at the beginning of the machine cycle which follows the instruction that sets ADCS.
ADCS is actually implemented with tpw flip-flops: a command flip-flop which is affected by set
operations, and a status flag which is accessed during read operations.
The next two machine cycles are used to initiate the converter. At the end of the first cycle, the ADCS
status flag is set end a value of “1” will be returned if the ADCS flag is read while the conversion is in
progress. Sampling of the analog input commences at the end of the second cycle.
During the next eight machine cycles, the voltage at the previously selected pin of one of analog input
pin is sampled, and this input voltage should be stable in order to obtain a useful sample. In any event,
the input voltage slew rate must be less than 10V/ms in order to prevent an undefined result.
The successive approximation control logic first sets the most significant bit and clears all other bits in
the successive approximation register (10 0000 0000b). The output of the DAC (50% full scale) is
compared to the input voltage Vin. If the input voltage is greater than VDAC, then the bit remains set;
otherwise if is cleared.
The successive approximation control logic now sets the next most significant bit (11 0000 0000b or
01 0000 0000b, depending on the previous result), and the VDAC is compared to Vin again. If the
input voltage is greater then VDAC, then the bit remains set; otherwise it is cleared. This process is
repeated until all ten bits have been tested, at which stage the result of the conversion is held in the
successive approximation register. The conversion takes four machine cycles per bit.
The end of the 10-bit conversion is flagged by control bit ADCCON.4 (ADCI). The upper 8 bits of the
result are held in special function register ADCH, and the two remaining bits are held in ADCCON.7
(ADC.1) and ADCCON.6 (ADC.0). The user may ignore the two least significant bits in ADCCON and
use the ADC as an 8-bit converter (8 upper bits in ADCH). In any event, the total actual conversion
time is 52 machine cycles. ADCI will be set and the ADCS status flag will be reset 52 cycles after the
ADCS is set. Control bits ADCCON.0 and ADCCON.1 are used to control an analog multiplexer which
selects one of 4 analog channels. An ADC conversion in progress is unaffected by an external or
software ADC start. The result of a completed conversion remains unaffected provided ADCI = logic 1;
a new ADC conversion already in progress is aborted when the idle or power down mode is entered.
The result of a completed conversion (ADCI = logic 1) remains unaffected when entering the idle
mode.
- 101 -
Publication Release Date: February 21, 2008
Revision A9
W79E825A/824A/823B/822B Data Sheet
MSB
Start
DAC
Successive
Approximation
Register
Successive
Approximation
Control Logic
LSB
Ready
(Stop)
Comparator
-
VDAC
Vin
+
Figure 24-1: Successive Approximation ADC
24.1 ADC Resolution and Analog Supply:
The ADC circuit has its own supply pins (AVDD and AVSS) and one pins (Vref+) connected to each
end of the DAC’s resistance-ladder that the AVDD and Vref+ are connected to VDD and AVSS is
connected to VSS. The ladder has 1023 equally spaced taps, separated by a resistance of “R”. The
first tap is located 0.5×R above AVSS, and the last tap is located 0.5×R below Vref+. This gives a total
ladder resistance of 1024×R. This structure ensures that the DAC is monotonic and results in a
symmetrical quantization error.
For input voltages between VSS and [(Vref+) + ½ LSB], the 10-bit result of an A/D conversion will be
0000000000B = 000H. For input voltages between [(Vref+) – 3/2 LSB] and Vref+, the result of a
conversion will be 1111111111B = 3FFH. Vref+ and AVSS may be between AVDD + 0.2V and VSS –
0.2 V. Vref+ should be positive with respect to VSS, and the input voltage (Vin) should be between
Vref+ and VSS.
The result can always be calculated from the following formula:
Result = 1024 ×
Vin
Vref +
or Result = 1024 ×
Vin
VDD
- 102 -
W79E825A/824A/823B/822B Data Sheet
VDD
ADC0(P0.3)
ADC1(P0.4)
ADC2(P0.5)
ADC3(P0.6)
Analog
Input
Multiplexer
Vref+
AVDD
ADC[9:0]
AADR[1:0]
ADCS
ADCI
0
10-bits
ADC Block
1
P1.4
ADCEX
FCPU /4
0
RC_CLK/2
1
ADCEN
AVSS
RCCLK
VSS
Figure 24-2: The ADC Block Diagram
- 103 -
Publication Release Date: February 21, 2008
Revision A9
W79E825A/824A/823B/822B Data Sheet
25 I2C SERIAL CONTROL
The I2C bus uses two wires (SDA and SCL) to transfer information between devices connected to the
bus. The main features of the bus are:
– Bidirectional data transfer between masters and slaves
– Multimaster bus (no central master)
– Arbitration between simultaneously transmitting masters without corruption of serial data on the bus
– Serial clock synchronization allows devices with different bit rates to communicate via one serial bus
– Serial clock synchronization can be used as a handshake mechanism to suspend and resume serial
transfer
– The I2C bus may be used for test and diagnostic purposes
STOP
Repeated
START
START
STOP
SDA
tBUF
tLOW
tr
SCL
tHD;STA
tf
tHIGH
tHD;DAT
tSU;DAT
tSU;STA
tSU;STO
Figure 25-1: I2C Bus Timing
The device’s on-chip I2C logic provides the serial interface that meets the I2C bus standard mode
specification. The I2C logic handles bytes transfer autonomously. It also keeps track of serial
transfers, and a status register (I2STATUS) reflects the status of the I2C bus.
The I2C port, SCL and SDA are at P1.2 and P1.3. When the I/O pins are used as I2C port, user must
set the pins to logic high in advance. When I2C port is enabled by setting ENS to high, the internal
states will be controlled by I2CON and I2C logic hardware. Once a new status code is generated and
stored in I2STATUS, the I2C interrupt flag (SI) will be set automatically. If both EA and EI2C are also
in logic high, the I2C interrupt is requested. The 5 most significant bits of I2STATUS stores the internal
state code, the lowest 3 bits are always zero and the content keeps stable until SI is cleared by
software.
25.1 SIO Port
The SIO port is a serial I/O port, which supports all transfer modes from and to the I2C bus. The
SIO port handles byte transfers autonomously. To enable this port, the bit ENS1 in I2CON
should be set to '1'. The CPU interfaces to the SIO port through the following six special
function registers: I2CON (control register, C0H), I2STATUS (status register, BDH), I2DAT (data
register, BCH), I2ADDR (address registers, C1H), I2CLK (clock rate register BEH) and I2TIMER
(Timer counter register, BFH). The SIO H/W interfaces to the I2C bus via two pins: SDA (P1.3,
serial data line) and SCL (P1.2, serial clock line). Pull up resistor is needed for Pin P1.2 and
P1.3 for I2C operation as these are 2 open drain pins.
- 104 -
W79E825A/824A/823B/822B Data Sheet
25.2 The I2C Control Registers:
The I2C has 1 control register (I2CON) to control the transmit/receive flow, 1 data register (I2DAT) to
buffer the Tx/Rx data, 1 status register (I2STATUS) to catch the state of Tx/Rx, recognizable slave
address register for slave mode use and 1 clock rate control block for master mode to generate the
variable baud rate.
25.2.1 The Address Registers, I2ADDR
I2C port is equipped with one slave address register. The contents of the register are irrelevant when
I2C is in master mode. In the slave mode, the seven most significant bits must be loaded with the
MCU’s own slave address. The I2C hardware will react if the contents of I2ADDR are matched with
the received slave address.
The I2C ports support the “General Call” function. If the GC bit is set the I2C port1 hardware will
respond to General Call address (00H). Clear GC bit to disable general call function.
When GC bit is set, the I2C is in Slave mode, it can be received the general call address by 00H
after Master send general call address to I2C bus, then it will follow status of GC mode. If it is
in Master mode, the AA bit must be cleared when it will send general call address of 00H to I2C
bus.
25.2.2 The Data Register, I2DAT
This register contains a byte of serial data to be transmitted or a byte which has just been received.
The CPU can read from or write to this 8-bit directly addressable SFR while it is not in the process of
shifting a byte. This occurs when SIO is in a defined state and the serial interrupt flag (SI) is set. Data
in I2DAT remains stable as long as SI bit is set. While data is being shifted out, data on the bus is
simultaneously being shifted in; I2DAT always contains the last data byte present on the bus. Thus, in
the event of arbitration lost, the transition from master transmitter to slave receiver is made with the
correct data in I2DAT.
I2DAT and the acknowledge bit form a 9-bit shift register, the acknowledge bit is controlled by the SIO
hardware and cannot be accessed by the CPU. Serial data is shifted through the acknowledge bit into
I2DAT on the rising edges of serial clock pulses on the SCL line. When a byte has been shifted into
I2DAT, the serial data is available in I2DAT, and the acknowledge bit (ACK or NACK) is returned by
the control logic during the ninth clock pulse. Serial data is shifted out from I2DAT on the falling edges
of SCL clock pulses, and is shifted into I2DAT on the rising edges of SCL clock pulses.
I2C Data Register:
I2DAT.7 I2DAT.6 I2DAT.5 I2DAT.4 I2DAT.3 I2DAT.2 I2DAT.1 I2DAT.0
shifting direction
- 105 -
Publication Release Date: February 21, 2008
Revision A9
W79E825A/824A/823B/822B Data Sheet
25.2.3 The Control Register, I2CON
The CPU can read from and write to this 8-bit, directly addressable SFR. Two bits are affected by
hardware: the SI bit is set when the I2C hardware requests a serial interrupt, and the STO bit is
cleared when a STOP condition is present on the bus. The STO bit is also cleared when ENS = "0".
ENSI
Set to enable I2C serial function block. When ENS=1 the I2C serial function enables. The
port latches of SDA1 and SCL1 must be set to logic high.
STA
I2C START Flag. Setting STA to logic 1 to enter master mode, the I2C hardware sends a
START or repeat START condition to bus when the bus is free.
STO
I2C STOP Flag. In master mode, setting STO to transmit a STOP condition to bus then
I2C hardware will check the bus condition if a STOP condition is detected this flag will be
cleared by hardware automatically. In a slave mode, setting STO resets I2C hardware to
the defined “not addressed” slave mode. This means it is NO LONGER in the slave
receiver mode to receive data from the master transmit device.
SI
I2C Port 1 Interrupt Flag. When a new SIO state is present in the S1STA register, the SI
flag is set by hardware, and if the EA and EI2C1 bits are both set, the I2C1 interrupt is
requested. SI must be cleared by software.
AA
Assert Acknowledge control bit. When AA=1 prior to address or data received, an
acknowledged (low level to SDA) will be returned during the acknowledge clock pulse on
the SCL line when 1.) A slave is acknowledging the address sent from master, 2.) The
receiver devices are acknowledging the data sent by transmitter. When AA=0 prior to
address or data received, a Not acknowledged (high level to SDA) will be returned during
the acknowledge clock pulse on the SCL line.
25.2.4 The Status Register, I2STATUS
I2STATUS is an 8-bit read-only register. The three least significant bits are always 0. The five most
significant bits contain the status code. There are 23 possible status codes. When I2STATUS contains
F8H, no serial interrupt is requested. All other I2STATUS values correspond to defined SIO states.
When each of these states is entered, a status interrupt is requested (SI = 1). A valid status code is
present in I2STATUS one machine cycle after SI is set by hardware and is still present one machine
cycle after SI has been reset by software.
25.2.5 The I2C Clock Baud Rate Bits, I2CLK
The data baud rate of I2C is determines by I2CLK register when SIO is in a master mode. It is not
important when SIO is in a slave mode. In the slave modes, SIO will automatically synchronize with
any clock frequency up to 400 KHz from master I2C device.
The data baud rate of I2C setting is Data Baud Rate of I2C = Fcpu / (I2CLK+1). The Fcpu=Fosc/4. If
Fosc = 16MHz, the I2CLK = 40(28H), so data baud rate of I2C = 16MHz/(4X (40 +1)) =
97.56Kbits/sec. The block diagram is as below figure.
- 106 -
W79E825A/824A/823B/822B Data Sheet
Figure 25-2: I2C Timer Count Block Diagram
25.3 Modes of Operation
The on-chip I2C ports support five operation modes, Master transmitter, Master receiver, Slave
transmitter, Slave receiver, and GC call.
In a given application, I2C port may operate as a master or as a slave. In the slave mode, the I2C port
hardware looks for its own slave address and the general call address. If one of these addresses is
detected, and if the slave is willing to receive or transmit data from/to master(by setting the AA bit),
acknowledge pulse will be transmitted out on the 9th clock, hence an interrupt is requested on both
master and slave devices if interrupt is enabled. When the microcontroller wishes to become the bus
master, the hardware waits until the bus is free before the master mode is entered so that a possible
slave action is not interrupted. If bus arbitration is lost in the master mode, I2C port switches to the
slave mode immediately and can detect its own slave address in the same serial transfer.
25.3.1 Master Transmitter Mode
Serial data output through SDA while SCL outputs the serial clock. The first byte transmitted contains
the slave address of the receiving device (7 bits) and the data direction bit. In this case the data
direction bit (R/W) will be logic 0, and it is represented by “W” in the flow diagrams. Thus the first byte
transmitted is SLA+W. Serial data is transmitted 8 bits at a time. After each byte is transmitted, an
acknowledge bit is received. START and STOP conditions are output to indicate the beginning and the
end of a serial transfer.
25.3.2 Master Receiver Mode
In this case the data direction bit (R/W) will be logic 1, and it is represented by “R” in the flow
diagrams. Thus the first byte transmitted is SLA+R. Serial data is received via SDA while SCL outputs
the serial clock. Serial data is received 8 bits at a time. After each byte is received, an acknowledge bit
is transmitted. START and STOP conditions are output to indicate the beginning and end of a serial
transfer.
25.3.3 Slave Receiver Mode
Serial data and the serial clock are received through SDA and SCL. After each byte is received, an
acknowledge bit is transmitted. START and STOP conditions are recognized as the beginning and
end of a serial transfer. Address recognition is performed by hardware after reception of the slave
address and direction bit.
- 107 -
Publication Release Date: February 21, 2008
Revision A9
W79E825A/824A/823B/822B Data Sheet
25.3.4 Slave Transmitter Mode
The first byte is received and handled as in the slave receiver mode. However, in this mode, the
direction bit will indicate that the transfer direction is reversed. Serial data is transmitted via SDA while
the serial clock is input through SCL. START and STOP conditions are recognized as the beginning
and end of a serial transfer.
25.4 Data Transfer Flow in Five Operating Modes
The five operating modes are: Master/Transmitter, Master/Receiver, Slave/Transmitter,
Slave/Receiver and GC Call. Bits STA, STO and AA in I2CON register will determine the next state of
the SIO hardware after SI flag is cleared. Upon complexion of the new action, a new status code will
be updated and the SI flag will be set. If the I2C interrupt control bits (EA and EI2) are enable,
appropriate action or software branch of the new status code can be performed in the Interrupt service
routine.
Data transfers in each mode are shown in the following figures.
*** Legend for the following five figures:
Last state
Last action is done
Next setting in S1CON
Expected next action
New state
next action is done
Software's access to S1DAT with respect to "Expected next action":
(1) Data byte will be transmitted:
Software should load the data byte (to be transmitted)
into S1DAT before new S1CON setting is done.
(2) SLA+W (R) will be transmitted:
Software should load the SLA+W/R (to be transmitted)
into S1DAT before new S1CON setting is done.
(STA,STO,SI,AA)=(0,0,0,X) (3) Data byte will be received:
Software can read the received data byte from S1DAT
SLA+W will be transmitted;
while a new state is entered.
ACK bit will be received.
08H
A START has been
transmitted.
18H
SLA+W has been transmitted;
ACK has been received.
Figure 25-3: Legen for the following four figures
- 108 -
W79E825A/824A/823B/822B Data Sheet
Figure 25-4: Master Transmitter Mode
- 109 -
Publication Release Date: February 21, 2008
Revision A9
W79E825A/824A/823B/822B Data Sheet
Figure 25-5: Master Receiver Mode
- 110 -
W79E825A/824A/823B/822B Data Sheet
Figure 25-6: Slave Transmitter Mode
- 111 -
Publication Release Date: February 21, 2008
Revision A9
W79E825A/824A/823B/822B Data Sheet
Figure 25-7:Slave Receiver Mode
- 112 -
W79E825A/824A/823B/822B Data Sheet
Figure 25-8:GC Mode
- 113 -
Publication Release Date: February 21, 2008
Revision A9
W79E825A/824A/823B/822B Data Sheet
26 ICP(IN-CIRCUIT PROGRAM) FLASH PROGRAM
The contexts of flash in W79E825 series are empty by default. User must program the flash EPROM
by external Writer device or by ICP (In-Circuit Program) tool.
In the ICP tool, the user must take note of ICP’s program pins used in system board. In some
application circuits, the pins are located at P1.5, P0.4 and P0.5, as below figure. During ICP
programming, P1.5 must be set to high voltage (~10.5V), and keeping this voltage to update code,
data and/or configure CONFIG bits. After programming completion, the high voltage of P1.5 should be
released. So, it is highly recommended user power off then power on after ICP programming has
completed on the system board.
Upon entry into ICP program mode, all pin will be set to quasi-bidirectional mode, and output to level
“1”.
The W79E825 series support programming of Flash EPROM (16K/8K/4K/2K bytes AP Flash EPROM)
and NVM data memory (256/128 bytes). User has the option to program the AP flash and NVM either
individually or both.
Vcc
ICP Power
Jumper
ICP Connector
Vdd
Vdd
Vpp
RST
Data
P0.4
Clock
P0.5
Vss
Jumper
To Reset or Input Pin
To I/O pin
To I/O pin
Vss
W79E825 Series
System Board
Figure 26-1: Application Circuit of ICP
Note: 1. When using ICP to upgrade code, the P1.5, P0.4 and P0.5 must be taken within design system board.
2. After program finished by ICP, to suggest system power must power off and remove ICP connector then power
on.
3. It is recommended that user performs erase function and programming configure bits continuously
without any interruption.
- 114 -
W79E825A/824A/823B/822B Data Sheet
27 CONFIG BITS
The W79E825 series have two CONFIG bits (CONFIG1, CONFIG2) that must be define at power up
and can not be set after the program start of execution. Those features are configured through the use
of two flash EPROM bytes, and the flash EPROM can be programmed and verified repeatedly. Until
the code inside the Flash EPROM is confirmed OK, the code can be protected. The protection of flash
EPROM (CONFIG2) and those operations on it are described below. The data of these bytes may be
read by the MOVC instruction at the addresses.
27.1 CONFIG1
BIT
NAME
7
-
FUNCTION
Reserved.
6
RPD
Reset Pin Disable bit:
0: Enable Reset function of Pin 1.5.
1: Disable Reset function of Pin 1.5, and it to be used as an input port pin.
5
PRHI
Port Reset High or Low bit:
0: Port reset to low state.
1: Port reset to high state.
4
BOV
Brownout Voltage Select bit:
0: Brownout detect voltage is 3.8V.
1: Brownout detect voltage is 2.5V.
- 115 -
Publication Release Date: February 21, 2008
Revision A9
W79E825A/824A/823B/822B Data Sheet
Continued
BIT
NAME
FUNCTION
3
-
Reserved.
2
-
Reserved.
1
Fosc1
CPU Oscillator Type Select bit 1
0
Fosc0
CPU Oscillator Type Select bit 0
Oscillator Configuration bits:
FOSC1
FOSC0
OSC SOURCE
0
0
4MHz ~ 20MHz crystal
0
1
Internal RC Oscillator
1
0
Reserved
1
1
External Oscillator in XTAL1
27.2 CONFIG2
CONFIG 2 :
7
6
5
4
3
2
1
0
C7
C6
-
-
-
-
-
-
CONFIG Bit
C7: 16K/8K/4K/2K Flash EPROM Code Lock Bit.
C6: 256/128 byte Data Lock Bit.
CONFIG Register 2
C7: 16K/8K/4K/2K Flash EPROM Lock bit
This bit is used to protect the customer's program code. It may be set after the programmer finishes
the programming and verifies sequence. Once this bit is set to logic 0, both the Flash EPROM data
and CONFIG Registers can not be accessed again.
C6: 256/128 byte Data Flash EPROM Lock bit
This bit is used to protect the customer's data code. It may be set after the programmer finishes the
programming and verifies sequence. Once this bit is set to logic 0, both the data Flash EPROM and
CONFIG Registers can not be accessed again.
- 116 -
W79E825A/824A/823B/822B Data Sheet
BIT 7
BIT 6
FUNCTION DESCRIPTION
1
1
Both security of 16KB/8KB/4KB/2KB program code and 256/128 Bytes data
area are unlocked. They can be erased, programmed or read by Writer or ICP.
0
1
The 16KB/8KB/4KB/2KB program code area is locked. It can’t be read by Writer
or ICP.
1
0
Don’t support (Invalid).
0
0
Both security of 16KB/8KB/4KB/2KB program code and 256/128 Bytes data
area are locked. They can’t be read by Writer or ICP.
- 117 -
Publication Release Date: February 21, 2008
Revision A9
W79E825A/824A/823B/822B Data Sheet
28 ELECTRICAL CHARACTERISTICS
28.1 Absolute Maximum Ratings
SYMBOL
PARAMETER
MIN
MAX
UNIT
VDD−VSS
-0.3
+7.0
V
Input Voltage
VIN
VSS-0.3
VDD+0.3
V
Operating Temperature
TA
-40
+85
°C
Storage Temperature
Tst
-55
+150
°C
-
120
mA
Maximum Current out of VSS
120
mA
Maximum Current suck by a
I/O pin
25
mA
Maximum Current sourced by
a I/O pin
25
mA
Maximum Current suck by
total I/O pins
75
mA
Maximum Current sourced by
total I/O pins
75
mA
DC Power Supply
Maximum Current into VDD
Note: Exposure to conditions beyond those listed under absolute maximum ratings may adversely affects the lift and reliability
- 118 -
W79E825A/824A/823B/822B Data Sheet
28.2 DC ELECTRICAL CHARACTERISTICS
(TA = -40~85°C, unless otherwise specified.)
PARAMETER
SPECIFICATION
SYMBOL
MIN.
Operating Voltage
VDD
TYP.
2.7
MAX.
TEST CONDITIONS
UNIT
5.5
V
18
25
mA
No load, /RST = VSS,VDD=
5.0V @ 20MHz
6
8
mA
No load, /RST = VSS,
VDD= 3.0V @ 12MHz
23
29
mA
VDD = 5.0V @ 20MHz, No
load, /RST = VDD, Run
NOP
6.5
9
mA
VDD = 3.0V @ 12MHz, No
load, /RST = VDD, Run
NOP
11.5
15
mA
No load, VDD = 5.5V
@ 20MHz
5
6.5
mA
No load, VDD = 3.0V
@ 12MHz
1
10
μA
No load, VDD = 5.5V
@ Disable BOV function
1
10
uA
No load, VDD = 3.0V
@ Disable BOV function
IDD1
Operating Current
IDD2
IIDLE
Idle Current
IPWDN
VDD=4.5V ~ 5.5V @
20MHz
VDD=2.7V ~ 5.5V @
12MHz
Power Down Current
IIN1
-50
-
+15
μA
VDD = 5.5V, 0<VIN<VDD
IIN2
-55
-45
-30
μA
VDD = 5.5V, VIN=0.45V
ILK
-10
-
+10
μA
VDD = 5.5V, 0<VIN<VDD
Logic 1 to 0 Transition
Current P0, P1, P2
ITL[*3]
-500
-
-200
μA
VDD = 5.5V, VIN<2.0V
Input Low Voltage P0,
P1, P2
(TTL input)
VIL1
0
-
0.8
V
VDD = 4.5V
0
-
0.6
V
VDD = 3.0V
Input Current P0, P1, P2
Input Current /RST
[*1]
Input Leakage Current
P0, P1, P2 (Open Drain)
- 119 -
Publication Release Date: February 21, 2008
Revision A9
W79E825A/824A/823B/822B Data Sheet
DC ELECTRICAL CHARACTERISTICS, continued
PARAMETER
SPECIFICATION
SYMBOL
MIN.
Input Low Voltage
XTAL1[*2]
VIL3
Input High Voltage
XTAL1[*2]
VIH3
Input High Voltage P0,
P1, P2 (TTL input)
VIH1
TYP.
MAX.
TEST CONDITIONS
UNIT
0
-
0.8
V
VDD = 4.5V
0
-
0.4
V
VDD = 3.0V
3.5
-
VDD +0.2
V
VDD = 5.5V
2.4
-
VDD +0.2
V
VDD = 3.0V
2.4
-
VDD +0.2
V
VDD = 5.5V
2.0
-
VDD +0.2
V
VDD = 3.0V
Negative going threshold
(Schmitt input)
VILS
-0.5
-
0.3VDD
V
Positive going threshold
(Schmitt input)
VIHS
0.7VDD
-
VDD+0.5
V
Hysteresis voltage
VHY
Source Current P0, P1,
P2
(Quasi-bidirectional
Mode)
Isr1
-180
-210
-360
uA
VDD = 4.5V, VS = 2.4V
Sink Current P0, P1, P2
(Quasi-bidirectional
Mode)
ISK2
13
18.5
24
mA
VDD = 4.5V, VS = 0.45V
Output Low Voltage P0,
P1, P2
(PUSH-PULL Mode)
-
0.5
0.9
V
VDD = 4.5V, IOL = 20 mA
VOL1
-
0.1
0.4
V
VDD = 2.7V, IOL = 3.2 mA
Output High Voltage P0,
P1, P2
(PUSH-PULL Mode)
2.4
3.4
-
V
VDD = 4.5V, IOH = -16mA
VOH
1.9
2.4
-
V
VDD = 2.7V, IOH = -3.2mA
0.2VDD
V
Brownout voltage with
BOV=1
VBO2.5
2.4
-
2.7
V
TA = -0 to 70°C
Brownout voltage with
BOV=0
VBO3.8
3.5
-
4.0
V
TA = -0 to 70°C
Comparator Reference
Voltage
Vref
1.02
1.20
1.31
V
Notes: *1. /RST pin is a Schmitt trigger input.
*2. XTAL1 is a CMOS input.
*3. Pins of P0, P1 and P2 can source a transition current when they are being externally driven from 1 to 0. The
transition current reaches its maximum value when Vin approximates to 2V.
- 120 -
W79E825A/824A/823B/822B Data Sheet
28.3 The ADC Converter DC ELECTRICAL CHARACTERISTICS
(VDD−VSS = 3.0~5V, TA = -40~85°C, Fosc = 20MHz, unless otherwise specified.)
PARAMETER
SPECIFICATION
SYMBOL
MIN.
Analog input
ADC clock
TYP.
TEST CONDITIONS
MAX.
UNIT
AVIN
VSS-0.2
VDD+0.2
V
ADCCLK
200KH
z
5MHz
Hz
Conversion time
52tADC[1]
tC
ADC circuit input
clock
us
Differential non-linearity
DNL
-1
-
+1
LSB
Integral non-linearity
INL
-2
-
+2
LSB
Offset error
Ofe
-1
-
+1
LSB
Gain error
Ge
-1
-
+1
%
Absolute voltage error
Ae
-3
-
+3
LSB
Notes: 1. tADC: The period time of ADC input clock.
28.4 The COMPARATOR ELECTRICAL CHARACTERISTICS
(VDD−VSS = 3.0~5V, TA = -40~85°C, Fosc = 20MHz, unless otherwise specified.)
PARAMETER
SPECIFICATION
SYMBOL
MIN.
Common mode range
comparator inputs
VCR
Common mode rejection ratio
TYP.
0
MAX.
UNIT
VDD-0.3
V
-50
dB
CMRR
Response time
tRS
-
30
100
ns
Comparator enable to output
valid time
tEN
-
1
5
us
Input leakage current,
comparator
IIL
-10
0
10
uA
TEST
CONDITIONS
0< VIN <VDD
28.5 AC ELECTRICAL CHARACTERISTICS
tCLCL
tCLCH
tCLCX
tCHCL
tCHCX
Note: Duty cycle is 50%.
- 121 -
Publication Release Date: February 21, 2008
Revision A9
W79E825A/824A/823B/822B Data Sheet
28.6 EXTERNAL CLOCK CHARACTERISTICS
PARAMETER
SYMBOL
MIN.
TYP.
MAX.
UNITS
Clock High Time
tCHCX
12.5
-
-
nS
Clock Low Time
tCLCX
12.5
-
-
nS
Clock Rise Time
tCLCH
-
-
10
nS
Clock Fall Time
tCHCL
-
-
10
nS
NOTES
28.7 AC SPECIFICATION
PARAMETER
SYMBOL
Oscillator Frequency
1/tCLCL
VARIABLE CLOCK MIN. VARIABLE CLOCK MAX.
0
UNITS
20
MHz
28.8 TYPICAL APPLICATION CIRCUITS
CRYSTAL
C1
C2
R
4MHz ~ 20 MHz
without
without
without
The above table shows the reference values for crystal applications.
C1
XTAL1
R
XTAL2
C2
W79E825
W79E824
W79E823
W79E822
- 122 -
W79E825A/824A/823B/822B Data Sheet
29 PACKAGE DIMENSIONS
29.1 20-pin SOP
11
20
c
E
HE
L
10
1
D
0.25
O
A
Y
SEATING PLANE
e
GAUGE PLANE
A1
b
Control demensions are in milmeters .
SYMBOL
A
A1
b
c
E
D
e
HE
Y
L
θ
DIMENSION IN MM
MIN.
MAX.
2.35
2.65
0.10
0.30
0.51
0.33
0.23
0.32
7.40
7.60
13.00
12.60
1.27 BSC
10.65
10.00
0.10
1.27
0.40
0
8
DIMENSION IN INCH
MIN.
MAX.
0.093
0.104
0.012
0.004
0.013
0.020
0.009
0.013
0.291
0.299
0.512
0.496
0.050 BSC
0.394
0.016
0
0.419
0.004
0.050
8
Figure 29-1: 20L SOP-300mil
- 123 -
Publication Release Date: February 21, 2008
Revision A9
W79E825A/824A/823B/822B Data Sheet
29.2 20-pin DIP
D
20
11
1
10
1
E
E
S
c
1
2
AA
A
L
Base Plane
Seating Plane
B
e1
α
B1
Symbol
A
A1
A2
B
B1
c
D
E
E1
e1
L
Dimension in inch
Min
Max
Dimension in mm
Min
Nom
0.010
Max
4.45
0.175
0.25
0.125
0.130
0.135
3.18
3.30
3.43
0.016
0.018
0.022
0.41
0.46
0.56
0.058
0.060
0.064
1.47
1.52
1.63
0.010
0.014
0.20
1.026
1.040
0.008
0.25
0.36
20.06
26.42
0.290
0.300
0.310
7.37
7.62
7.87
0.245
0.250
0.255
6.22
6.35
6.48
0.090
0.100
0.110
2.29
2.54
2.79
0.120
0.130
0.140
3.05
3.30
3.56
15
0
0.375
8.51
9.02
9.53
α
0
eA
0.335
S
Nom
0.355
15
0.075
Figure 29-2: 20L PDIP 300mil
- 124 -
1.91
eA
W79E825A/824A/823B/822B Data Sheet
30 REVISION HISTORY
VERSION
DATE
PAGE
A1
Mar. 30, 2006
-
A2
June 04, 2006
A3
June 19, 2006
4~5
A4
June 23, 2006
86~92
Oct. 04, 2006
8
98
112~114
96
89
A5
61
Mar. 12, 2007
26
95~98
105
18
19
A7
Jul. 16, 2007
30
31
59
63
112
92
101
A8
Dec. 27, 2007
Initial Issued
To add W79E823/822 parts and function description
112
A6
DESCRIPTION
26
To remove normal package of part number list
To revise PWM function of W79E823 and W79E822 to 4
PWM output channel
1. To remove block diagram.
2. To add GC call function description.
3. Revise DC characteristics spec.
4. Revise Timer Counter of I2C block diagram.
5. Revise “Release brake of PWM” flow chart.
1. Added note for icp mode.
2. Change SFR name IE1 to EIE due to conflict with IE1
bit name in TCON.3.
3. SFR Reset Value Table: Added PWMCON3,
NVMADDR, NVMDAT & NVMCON. Rename PWMP1
to PWMPH, PWMP0 to PWMPL.
4. Port 2 SFR bit P2.0 and P2.1 descriptions reverse
order.
5. To revise PWM function of W79E823, W79E822 and
W79E821 to 4 PWM output channel.
6. Revise Timer Counter of I2C block diagram.
1. Added SFR reg bit P1M1.2, P1M2.2, P1M1.3,
P1M2.3.
2. Port1 SFR register for bit P0.7~P0.0 description in
reverse order.
3. Removed Port1 output mode reg bit P1M1.5, P1M2.5
4. Revised reg bit ENCLK description
5. Changed the “external reset pin has to be held low for
at least two machine cycles”.(not held high)
6. Changed the “All the bits that generate interrupts can
be set or reset by software”. (not by hardware)
7. Revised Figure 26-30-1: Application Circuit of ICP
8. Revised Figure 21-1: Oscillator
9. Revised Figure 24-2: The ADC Block Diagram
Revise the content of UART mode select table.
(SM0, SM1) is exchanged.
- 125 -
Publication Release Date: February 21, 2008
Revision A9
W79E825A/824A/823B/822B Data Sheet
89
63,64
1. Updated keyboard interrupt diagram. IE1 changed to
EIE.
2. Update part name in header with version appended
3. Update Maximum rating table
4. Modify power down wakeup by external interrupt pins
5. Revise max of IIN1 to 15uA
6. Change to header 6.3 for “Serial I/O”
7. Update SFR PWMCON1 bit names PWMF, PWM0L,
PWM1L, PWM2L, PWM3L to CF, PWM0I, PWM1I,
PWM2I, PWM3I
8. Update EWRST = 0, TA = FFH initial value after reset
9. Rename INT0 and INT1 to /INT0 and /INT1
10.Type error:
a. 13 interrupt sources.
b. Corrected grammar.
c. Changed EWDRST to EWRST.
d. Changed ENT0 and ENT1 bits to T0OE and
T1OE.
e. “pre machine cycle” should be “per machine
cycle”
f. Change “fail time” to “fall time”
g. P2M1 change to P2M2
h. Mnemonic PWM2L change to PWM3L
11. Added Idd2 in dc spec.
12. Removed 24 pin package dimension
13. Update dual data pointer diagram
14. Update WDT block diagram: IE1.4 to EIE.4, WDRF
to WTRF
15. Internal oscillator update (Fosc1,Fosc0) = 01b
16. Update ADCS bit descriptions
17. All WDCON bits except WTRF are TA protected
18. Revise table 12-3 Vector location for Interrupt
sources and power down wakeup, for watchdog
timerdoes not support power dowm mode wakeup
19. Add Figure11-1, 11-2 for reset and VDD monitor timing
60
77
79,115
103
20. Revise Chapter 11.1.2 Power-ON reset description
21. Revise Figure 15-1 Watchdog Timer diagram
22. Remove Config1 bit7 WDTE function
23. Revise Figure 24-2 ADC Block diagra
118
59
119
9
41
18
24,66,68
67
71,73
78
91
95
A9
Feb. 21, 2008
96
31
42
119
124
10
77
94
44
40,79
67
diagram
- 126 -
W79E825A/824A/823B/822B Data Sheet
Important Notice
Winbond products are not designed, intended, authorized or warranted for use as components
in systems or equipment intended for surgical implantation, atomic energy control
instruments, airplane or spaceship instruments, transportation instruments, traffic signal
instruments, combustion control instruments, or for other applications intended to support or
sustain life. Further more, Winbond products are not intended for applications wherein failure
of Winbond products could result or lead to a situation wherein personal injury, death or
severe property or environmental damage could occur.
Winbond customers using or selling these products for use in such applications do so at their
own risk and agree to fully indemnify Winbond for any damages resulting from such improper
use or sales.
- 127 -
Publication Release Date: February 21, 2008
Revision A9