XILINX XC2C64A

0
R
CoolRunner-II CPLD Family
DS090 (v2.5) June 28, 2005
0
0
Product Specification
Features
•
•
•
-
Optimized for 1.8V systems
- Industry’s fastest low power CPLD
- Densities from 32 to 512 macrocells
Industry’s best 0.18 micron CMOS CPLD
- Optimized architecture for effective logic synthesis
- Multi-voltage I/O operation — 1.5V to 3.3V
Advanced system features
- Fastest in system programming
·
1.8V ISP using IEEE 1532 (JTAG) interface
- On-The-Fly Reconfiguration (OTF)
- IEEE1149.1 JTAG Boundary Scan Test
- Optional Schmitt trigger input (per pin)
- Multiple I/O banks on all devices
- Unsurpassed low power management
·
DataGATE external signal control
- Flexible clocking modes
·
Optional DualEDGE triggered registers
·
Clock divider (÷ 2,4,6,8,10,12,14,16)
·
CoolCLOCK
- Global signal options with macrocell control
·
Multiple global clocks with phase selection per
macrocell
·
Multiple global output enables
·
Global set/reset
- Abundant product term clocks, output enables and
set/resets
- Efficient control term clocks, output enables and
set/resets for each macrocell and shared across
function blocks
- Advanced design security
- Open-drain output option for Wired-OR and LED
drive
- Optional bus-hold, 3-state or weak pullup on select
I/O pins
- Optional configurable grounds on unused I/Os
•
•
•
•
•
Mixed I/O voltages compatible with 1.5V, 1.8V,
2.5V, and 3.3V logic levels on all parts
- SSTL2_1,SSTL3_1, and HSTL_1 on 128
macrocell and denser devices
- Hot pluggable
PLA architecture
- Superior pinout retention
- 100% product term routability across function block
Wide package availability including fine pitch:
- Chip Scale Package (CSP) BGA, Fine Line BGA,
TQFP, PQFP, VQFP, PLCC, and QFN packages
- Pb-free available for all packages
Design entry/verification using Xilinx and industry
standard CAE tools
Free software support for all densities using Xilinx
WebPACK™
Industry leading nonvolatile 0.18 micron CMOS
process
- Guaranteed 1,000 program/erase cycles
- Guaranteed 20 year data retention
Family Overview
Xilinx CoolRunner™-II CPLDs deliver the high speed and
ease of use associated with the XC9500/XL/XV CPLD family with the extremely low power versatility of the XPLA3™
family in a single CPLD. This means that the exact same
parts can be used for high-speed data communications/
computing systems and leading edge portable products,
with the added benefit of In System Programming. Low
power consumption and high-speed operation are combined into a single family that is easy to use and cost effective. Clocking techniques and other power saving features
extend the users’ power budget. The design features are
supported starting with Xilinx ISE 4.1i ISE WebPACK. Additional details can be found in Further Reading, page 13.
Table 1 shows the macrocell capacity and key timing
parameters for the CoolRunner-II CPLD family.
Table 1: CoolRunner-II CPLD Family Parameters
XC2C32A
XC2C64A
XC2C128
XC2C256
XC2C384
XC2C512
Macrocells
32
64
128
256
384
512
Max I/O
33
64
100
184
240
270
TPD (ns)
3.8
4.6
5.7
5.7
7.1
7.1
TSU (ns)
1.9
2.0
2.4
2.4
2.9
2.6
TCO (ns)
3.7
3.9
4.2
4.5
5.8
5.8
FSYSTEM1 (MHz)
323
263
244
256
217
179
© 2005 Xilinx, Inc. All rights reserved. All Xilinx trademarks, registered trademarks, patents, and disclaimers are as listed at http://www.xilinx.com/legal.htm.
All other trademarks and registered trademarks are the property of their respective owners. All specifications are subject to change without notice.
DS090 (v2.5) June 28, 2005
Product Specification
www.xilinx.com
1
R
CoolRunner-II CPLD Family
Table 2: CoolRunner-II CPLD DC Characteristics
XC2C32A
XC2C64A
XC2C128
XC2C256
XC2C384
XC2C512
ICC (µA), 0 MHz, 25°C (typical)
16
17
19
21
23
25
ICC (mA), 50 MHz, 70°C (max)
2.5
5
10
27
45
55
ICC is dynamic current.
With the exception of the new Pb-free QF packages, there
are at least two densities present in each package with
three in the VQ100 (100-pin 1.0mm QFP) and TQ144
(144-pin 1.4mm QFP), and in the FT256 (256-ball 1.0mm
spacing FLBGA). The FT256 is particularly important for
slim dimensioned portable products with mid- to high-density logic requirements.
Table 2 shows key DC characteristics for the CoolRunner-II
family.
Table 3 shows the CoolRunner-II CPLD package offering
with corresponding I/O count. All packages are surface
mount, with over half of them being ball-grid technologies.
The ultra tiny packages permit maximum functional capacity
in the smallest possible area. The CMOS technology used
in CoolRunner-II CPLDs generates minimal heat, allowing
the use of tiny packages during high-speed operation.
Table 3: CoolRunner-II CPLD Family Packages and I/O Count
XC2C32
QFG32(1)
PC44
33
PCG44(1)
VQ44
CP56
XC2C64
XC2C64A
XC2C128
XC2C256
XC2C384
XC2C512
21
-
-
-
-
-
-
33
33
33
-
-
-
-
33
-
-
-
-
33
-
-
-
-
33
-
-
-
-
33
33
VQG44(1)
QFG48(1)
XC2C32A
33
33
33
-
-
-
37
-
-
-
-
33
33
45
45
-
-
-
-
45
-
-
-
-
64
80
80
-
-
64
80
80
-
-
CPG56(1)
33
VQ100
-
-
64
VQG100(1)
-
-
CP132
-
-
-
-
100
106
-
-
CPG132(1)
-
-
-
-
100
106
-
-
TQ144
-
-
-
-
100
118
118
-
TQG144(1)
-
-
-
-
100
118
118
-
PQ208
-
-
-
-
-
173
173
173
PQG208(1)
-
-
-
-
-
173
173
173
FT256
-
-
-
-
-
184
212
212
FTG256(1)
-
-
-
-
-
184
212
212
FG324
-
-
-
-
-
-
240
270
FGG324(1)
-
-
-
-
-
-
240
270
Notes:
1. The letter "G" as the third character indicates a Pb-free package.
Table 4 details the distribution of advanced features across
the CoolRunner-II CPLD family. The family has uniform
basic features with advanced features included in densities
where they are most useful. For example, it is very unlikely
that four I/O banks are needed on 32 and 64 macrocell
2
parts, but very likely they are for 384 and 512 macrocell
parts. The I/O banks are groupings of I/O pins using any
one of a subset of compatible voltage standards that share
the same VCCIO level. (See Table 5 for a summary of
CoolRunner-II I/O standards.)
www.xilinx.com
DS090 (v2.5) June 28, 2005
Product Specification
R
CoolRunner-II CPLD Family
Table 4: CoolRunner-II CPLD Family Features
XC2C32
XC2C32A
XC2C64
XC2C64A
XC2C128
XC2C256
XC2C384
XC2C512
IEEE 1532
✓
✓
✓
✓
✓
✓
✓
✓
I/O banks
1
2
1
2
2
2
4
4
Clock division
-
-
-
-
✓
✓
✓
✓
DualEDGE Registers
✓
✓
✓
✓
✓
✓
✓
✓
DataGATE
-
-
-
-
✓
✓
✓
✓
LVTTL
✓
✓
✓
✓
✓
✓
✓
✓
LVCMOS33, 25, 18,
and 15(1)
✓
✓
✓
✓
✓
✓
✓
✓
SSTL2_1
-
-
-
-
✓
✓
✓
✓
SSTL3_1
-
-
-
-
✓
✓
✓
✓
HSTL_1
-
-
-
-
✓
✓
✓
✓
Configurable ground
✓
✓
✓
✓
✓
✓
✓
✓
Quadruple data
security
✓
✓
✓
✓
✓
✓
✓
✓
Open drain outputs
✓
✓
✓
✓
✓
✓
✓
✓
Hot plugging
✓
✓
✓
✓
✓
✓
✓
✓
Schmitt Inputs
✓
✓
✓
✓
✓
✓
✓
✓
(1) LVCMOS15 requires the use of Schmitt-trigger inputs.
Architecture Description
CoolRunner-II CPLD is a highly uniform family of fast, low
power CPLDs. The underlying architecture is a traditional
CPLD architecture combining macrocells into Function
Blocks (FBs) interconnected with a global routing matrix,
the Xilinx Advanced Interconnect Matrix (AIM). The Function Blocks use a Programmable Logic Array (PLA) configuration which allows all product terms to be routed and
shared among any of the macrocells of the FB. Design software can efficiently synthesize and optimize logic that is
subsequently fit to the FBs and connected with the ability to
utilize a very high percentage of device resources. Design
changes are easily and automatically managed by the software, which exploits the 100% routability of the Programmable Logic Array within each FB. This extremely robust
DS090 (v2.5) June 28, 2005
Product Specification
building block delivers the industry’s highest pinout retention, under very broad design conditions. The architecture
will be explained by expanding the detail as we discuss the
underlying Function Blocks, logic and interconnect.
The design software automatically manages these device
resources so that users can express their designs using
completely generic constructs without knowledge of these
architectural details. More advanced users can take advantage of these details to more thoroughly understand the
software’s choices and direct its results.
Figure 1 shows the high-level architecture whereby Function Blocks attach to pins and interconnect to each other
within the internal interconnect matrix. Each FB contains 16
macrocells. The BSC path is the JTAG Boundary Scan Con-
www.xilinx.com
3
R
CoolRunner-II CPLD Family
trol path. The BSC and ISP block has the JTAG controller
and In-System Programming Circuits.
BSC Path
Clock and Control Signals
Function
Block 1
Function
Block n
MC1
MC2
MC1
MC2
I/O Blocks
16 FB
16 FB
PLA
16
PLA
AIM
40
JTAG
MC16
Direct Inputs
Direct Inputs
16
16
40
MC16
I/O Pin
I/O Pin
I/O Pin
I/O Blocks
I/O Pin
I/O Pin
I/O Pin
16
BSC and ISP
DS090_01_121201
Figure 1: CoolRunner-II CPLD Architecture
Function Block
The CoolRunner-II CPLD Function Blocks contain 16 macrocells, with 40 entry sites for signals to arrive for logic creation and connection. The internal logic engine is a 56
product term PLA. All Function Blocks, regardless of the
number contained in the device, are identical. For a
high-level view of the Function Block, see Figure 2.
16
PLA
Out
To AIM
MC16
3
Global
Set/Reset
Global
Clocks
DS090_02_101001
Figure 2: CoolRunner-II CPLD Function Block
At the high level, it is seen that the product terms (p-terms)
reside in a programmable logic array (PLA). This structure
4
Classic CPLDs typically have a few product terms available
for a high-speed path to a given macrocell. They rely on
capturing unused p-terms from neighboring macrocells to
expand their product term tally, when needed. The result of
this architecture is a variable timing model and the possibility of stranding unusable logic within the FB.
The PLA is different — and better. First, any product term
can be attached to any OR gate inside the FB macrocell(s).
Second, any logic function can have as many p-terms as
needed attached to it within the FB, to an upper limit of 56.
Third, product terms can be re-used at multiple macrocell
OR functions so that within a FB, a particular logical product
need only be created once, but can be re-used up to 16
times within the FB. Naturally, this plays well with the fitting
software, which identifies product terms that can be shared.
MC1
MC2
40
is extremely flexible, and very robust when compared to
fixed or cascaded product term function blocks.
The software places as many of those functions as it can
into FBs, so it happens for free. There is no need to force
macrocell functions to be adjacent or any other restriction
save residing in the same FB, which is handled by the software. Functions need not share a common clock, common
set/reset or common output enable to take full advantage of
the PLA. Also, every product term arrives with the same
time delay incurred. There are no cascade time adders for
putting more product terms in the FB. When the FB product
term budget is reached, there is a small interconnect timing
penalty to route signals to another FB to continue creating
logic. Xilinx design software handles all this automatically.
www.xilinx.com
DS090 (v2.5) June 28, 2005
Product Specification
R
CoolRunner-II CPLD Family
Macrocell
The CoolRunner-II CPLD macrocell is extremely efficient
and streamlined for logic creation. Users can develop sum
of product (SOP) logic expressions that comprise up to 40
inputs and span 56 product terms within a single function
block. The macrocell can further combine the SOP expression into an XOR gate with another single p-term expression. The resulting logic expression’s polarity is also
selectable. As well, the logic function can be pure combinatorial or registered, with the storage element operating
selectably as a D or T flip-flop, or transparent latch. Available at each macrocell are independent selections of global, function block level or local p-term derived clocks, sets,
resets, and output enables. Each macrocell flip-flop is configurable for either single edge or DualEDGE clocking, providing either double data rate capability or the ability to
distribute a slower clock (thereby saving power). For single
edge clocking or latching, either clock polarity may be
selected per macrocell. CoolRunner-II macrocell details are
shown in Figure 3. Note that in Figure 4, standard logic
symbols are used except the trapezoidal multiplexers have
input selection from statically programmed configuration
select lines (not shown). Xilinx application note XAPP376
gives a detailed explanation of how logic is created in the
CoolRunner-II CPLD family.
From AIM
40
49 P-terms
To PTA, PTB, PTC of
other macrocells
4 P-terms
CTC, CTR,
CTS, CTE
Direct Input
from
I/O Block
Feedback
to AIM
PTA
PTB
VCC
PTC
PTA
CTS
GSR
GND
GND
PTC
PLA OR Term
CTC
PTC
To I/O Block
S
D/T
Q
CE
FIF
Latch
DualEDGE
CK
GCK0
GCK1
GCK2
R
PTA
CTR
GSR
GND
DS090_03_121201
Figure 3: CoolRunner-II CPLD Macrocell
When configured as a D-type flip-flop, each macrocell has
an optional clock enable signal permitting state hold while a
clock runs freely. Note that Control Terms (CT) are available
to be shared for key functions within the FB, and are generally used whenever the exact same logic function would be
repeatedly created at multiple macrocells. The CT product
terms are available for FB clocking (CTC), FB asynchronous set (CTS), FB asynchronous reset (CTR), and FB output enable (CTE).
Any macrocell flip-flop can be configured as an input register or latch, which takes in the signal from the macrocell’s
I/O pin, and directly drives the AIM. The macrocell combina-
DS090 (v2.5) June 28, 2005
Product Specification
tional functionality is retained for use as a buried logic node
if needed. FToggle is the maximum clock frequency to which
a T flip-flop can reliably toggle.
Advanced Interconnect Matrix (AIM)
The Advanced Interconnect Matrix is a highly connected
low power rapid switch. The AIM is directed by the software
to deliver up to a set of 40 signals to each FB for the creation of logic. Results from all FB macrocells, as well as, all
pin inputs circulate back through the AIM for additional connection available to all other FBs as dictated by the design
www.xilinx.com
5
R
CoolRunner-II CPLD Family
software. The AIM minimizes both propagation delay and
power as it makes attachments to the various FBs.
I/O Block
I/O blocks are primarily transceivers. However, each I/O is
either automatically compliant with standard voltage ranges
or can be programmed to become so. See XAPP382 for
detailed information on CoolRunner-II I/Os.
In addition to voltage levels, each input can selectively
arrive through Schmitt-trigger inputs. This adds a small time
delay, but substantially reduces noise on that input pin.
Approximately 500 mV of hysteresis will be added when
Schmitt-trigger inputs are selected. All LVCMOS inputs can
have hysteresis input. Hysteresis also allows easy generation of external clock circuits. The Schmitt-trigger path is
best seen in Figure 4. See Table 5 for Schmitt-trigger compatibility with I/O standards.
Outputs can be directly driven, 3-stated or open-drain configured. A choice of slow or fast slew rate output signal is
also available. Table 5 summarizes various supported voltage standards associated with specific part capacities. All
inputs and disabled outputs are voltage tolerant up to 3.3V.
The CoolRunner-II family supports SSTL2-1, SSTL3-1 and
HSTL-1 high-speed I/O standards in the 128-macrocell and
larger devices. Figure 4 details the I/O pin, where it is noted
that the inputs requiring comparison to an external reference voltage are available. These I/O standards all require
VREF pins for proper operation. The CoolRunner-II CPLD
allows any I/O pin to act as a VREF pin, granting the board
layout engineer extra freedom when laying out the
pins.However, if VREF pin placement is not done properly,
additional VREF pins may be required, resulting in a loss of
potential I/O pins or board re-work. See XAPP399 for
details regarding VREF pins and their placement.
VREF has pin-range requirements that must be observed.
The Xilinx software aids designers in remaining within the
proper pin range.
Available on 128 Macrocell Devices and Larger
To AIM
VREF
Hysteresis
To Macrocell
Direct Input
Enabled
CTE
PTB
4
GTS[0:3]
CGND
Open Drain
Disabled
Global termination
Pullup/Bus-Hold
VCCIO
From Macrocell
DS090_04_121201
Figure 4: CoolRunner-II CPLD I/O Block Diagram
Table 5 summarizes the single ended I/O standard support
and shows which standards require VREF values and board
termination. VREF detail is given in specific data sheets.
Table 5: CoolRunner-II CPLD I/O Standard Summary
IOSTANDARD
Attribute
VCCIO
Input VREF
Board Termination Voltage
(VTT)
Schmitt-trigger Support
LVTTL
3.3
N/A
N/A
Optional
LVCMOS33
3.3
N/A
N/A
Optional
LVCMOS25
2.5
N/A
N/A
Optional
LVCMOS18
1.8
N/A
N/A
Optional
LVCMOS15
1.5
N/A
N/A
Not optional
HSTL_1
1.5
0.75
0.75
Not optional
SSTL2_1
2.5
1.25
1.25
Not optional
SSTL3_1
3.3
1.5
1.5
Not optional
6
www.xilinx.com
DS090 (v2.5) June 28, 2005
Product Specification
R
CoolRunner-II CPLD Family
Output Banking
CPLDs are widely used as voltage interface translators. To
that end, the output pins are grouped in large banks. The
XC2C32 and XC2C64 devices are not banked, but the new
XC2C32A and XC2C64A devices have two banks. The
medium parts (128 and 256 macrocell) support two output
banks. With two, the outputs will switch to one of two
selected output voltage levels, unless both banks are set to
the same voltage. The larger parts (384 and 512 macrocell)
support four output banks split evenly. They can support
groupings of one, two, three or four separate output voltage
levels. This kind of flexibility permits easy interfacing to
3.3V, 2.5V, 1.8V, and 1.5V in a single part.
DataGATE
Low power is the hallmark of CMOS technology. Other
CPLD families use a sense amplifier approach to creating
product terms, which always has a residual current component being drawn. This residual current can be several hundred milliamps, making them unusable in portable systems.
CoolRunner-II CPLDs use standard CMOS methods to create the CPLD architecture and deliver the corresponding
low current consumption, without doing any special tricks.
However, sometimes designers would like to reduce their
system current even more by selectively disabling circuitry
not being used.
The patented DataGATE technology was developed to permit a straightforward approach to additional power reduction. Each I/O pin has a series switch that can block the
arrival of free running signals that are not of interest. Signals that serve no use may increase power consumption,
and can be disabled. Users are free to do their design, then
choose sections to participate in the DataGATE function.
DataGATE is a logic function that drives an assertion rail
threaded through the medium and high-density
CoolRunner-II CPLD parts. Designers can select inputs to
be blocked under the control of the DataGATE function,
DS090 (v2.5) June 28, 2005
Product Specification
effectively blocking controlled switching signals so they do
not drive internal chip capacitances. Output signals that do
not switch, are held by the bus hold feature. Any set of input
pins can be chosen to participate in the DataGATE function.
Figure 5 shows the familiar CMOS ICC versus switching frequency graph. With DataGATE, designers can approach
zero power, should they choose to, in their designs
Figure 6 shows how DataGATE basically works. One I/O
pin drives the DataGATE Assertion Rail. It can have any
desired logic function on it. It can be as simple as mapping
an input pin to the DataGATE function or as complex as a
counter or state machine output driving the DataGATE I/O
pin through a macrocell. When the DataGATE rail is
asserted high, any pass transistor switch attached to it is
blocked. Note that each pin has the ability to attach to the
AIM through a DataGATE pass transistor, and thus be
blocked. A latch automatically captures the state of the pin
when it becomes blocked. The DataGATE Assertion Rail
threads throughout all possible I/Os, so each can participate
if chosen. Note that one macrocell is singled out to drive the
rail, and that macrocell is exposed to the outside world
through a pin, for inspection. If DataGATE is not needed,
this pin is an ordinary I/O.
ICC
0
Frequency
DS090_05_101001
Figure 5: CMOS ICC vs. Switching Frequency Curve
www.xilinx.com
7
R
CoolRunner-II CPLD Family
DataGATE Assertion Rail
MC1
MC2
MC1
MC2
Latch
To AIM
PLA
PLA
Latch
Latch
To AIM
To AIM
MC16
MC16
AIM
MC1
MC2
MC1
MC2
PLA
PLA
Latch
Latch
To AIM
To AIM
MC16
MC16
DS090_06_111201
Figure 6: DataGATE Architecture (output drivers not shown)
Global Signals
Global signals, clocks (GCK), sets/resets (GSR) and output
enables (GTS), are designed to strongly resemble each
other. This approach enables design software to make the
best utilization of their capabilities. Each global capability is
supplemented by a corresponding product term version.
Figure 7 shows the common structure of the global signal
trees. The pin input is buffered, then drives multiple internal
global signal traces to deliver low skew and reduce loading
delays. The DataGATE assertion rail is also a global signal.
Additional Clock Options: Division,
DualEDGE, and CoolCLOCK
Division
Circuitry has been included in the CoolRunner-II CPLD
architecture to divide one externally supplied global clock
by standard values. Division by 2,4,6,8,10, 12, 14 and 16
are the options (see Figure 8). This capability is supplied on
the GCK2 pin. The resulting clock produced will be 50%
duty cycle for all possible divisions. Note that a Synchronous Reset (CDRST) is included to guarantee no runt
clocks can get through to the global clock nets. Note that
again, the signal is buffered and driven to multiple traces
with minimal loading and skew.
DualEDGE
DS090_07_101001
Figure 7: Global Clocks (GCK), Sets/Resets (GSR) and
Output Enables (GTS)
8
Each macrocell has the ability to double its input clock
switching frequency. Figure 9 shows the macrocell flip-flop
with the DualEDGE option (doubled clock) at each macrocell. The source to double can be a control term clock, a
product term clock or one of the available global clocks. The
ability to switch on both clock edges is vital for a number of
synchronous memory interface applications as well as certain double data rate I/O applications.
www.xilinx.com
DS090 (v2.5) June 28, 2005
Product Specification
R
CoolRunner-II CPLD Family
drain, the clock power can be reduced by driving the net at
half frequency, then doubling the clock rate using
DualEDGE triggering at the macrocells. Figure 10 shows
how CoolCLOCK is created by internal clock cascading with
the divider and DualEDGE flip-flop working together. See
XAPP378 for more detail.
CoolCLOCK
In addition to the DualEDGE flip-flop, additional power savings can be had by combining the clock division circuitry
with the DualEDGE circuitry. This capability is called CoolCLOCK and is designed to reduce clocking power within the
CPLD. Because the clock net can be an appreciable power
GCK2
Clock
In
÷2
÷4
÷6
÷8
÷10
÷12
÷14
÷16
CDRST
CDRST
DS090_08_121201
Figure 8: Clock Division Circuitry for GCK2
D/T
PTC
GCK0
GCK1
GCK2
CLK_CT
Q
FIF
CE
Latch
CK ✓DualEDGE
PTC
DS090_09_121201
Figure 9: Macrocell Clock Chain with DualEDGE Option Shown
D/T
PTC
CTC
GCK0
GCK1
GCK2
Q
FIF
CE
Latch
CK ✓DualEDGE
PTC
GCK2
Clock
In
÷2
÷4
÷6
÷8
÷10
÷12
÷14
÷16
Synch Rst
Synch Reset
DS090_10_121201
Figure 10: CoolCLOCK Created by Cascading Clock Divider and DualEDGE Option
DS090 (v2.5) June 28, 2005
Product Specification
www.xilinx.com
9
R
CoolRunner-II CPLD Family
Design Security
Designs can be secured during programming to prevent
either accidental overwriting or pattern theft via readback.
Four independent levels of security are provided on-chip,
eliminating any electrical or visual detection of configuration
patterns. These security bits can be reset only by erasing
the entire device. See WP170 for more detail.
Timing Model
Figure 11 shows the CoolRunner-II CPLD timing model. It
represents one aspect of the overall architecture from a tim-
ing viewpoint. Each little block is a time delay that a signal
will incur if the signal passes through such a resource. Timing reports are created by tallying the incremental signal
delays as signals progress within the CPLD. Software creates the timing reports after a design has been mapped
onto the specific part, and knows the specific delay values
for a given speed grade. Equations for the higher level timing values (i.e., TPD and FSYSTEM) are available. Table 6
summarizes the individual parameters and provides a brief
definition of their associated functions. Xilinx application
note XAPP375 details the CoolRunner-II CPLD family timing with several examples.
TF
TLOGI2
TIN
TLOGI1
TPDI
D/T
TCOI
TSUI THI
THYS
TSLEW
TECSU
TDIN
TOUT
TECHO
THYS
TCT
CE
TAOI
TGCK
TEN
S/R
THYS
TOEM
TGSR
THYS
TGTS
THYS
XAPP375_03_010303
Figure 11: CoolRunner-II CPLD Timing Model
Table 6: Timing Parameter Definitions (Continued)
Table 6: Timing Parameter Definitions
Symbol
Symbol
Parameter
Parameter
Buffer Delays
Macrocell Delays
TlN
Input Buffer Delay
TPDI
Macro cell input to output valid
TDIN
Direct data register input delay
TSUI
Macro register setup before clock
TGCK
Global clock (GCK) buffer delay
THI
Macro register hold after clock
TGSR
Global set/reset (GSR) buffer delay
TECSU
Macro register enable clock setup time
TGTS
Global output enable (GTS) buffer delay
TECHO
Macro register enable clock hold time
TOUT
Output buffer delay
TCOI
Macro register clock to output valid
TEN
Output buffer enable/disable delay
TAOI
Macro register set/reset to output valid
TSLEW
Output buffer slew rate control delay
THYS
Hysteresis selection delay adder
P-term Delays
Feedback Delays
TCT
Control Term delay (single PT or FB-CT)
TF
Feedback delay
TLOGI1
Single P-term logic delay
TOEM
Macrocell to Global OE delay
TLOGI2
Multiple P-term logic delay adder
10
www.xilinx.com
DS090 (v2.5) June 28, 2005
Product Specification
R
CoolRunner-II CPLD Family
Programming
The programming data sequence is delivered to the device
using either Xilinx iMPACT software and a Xilinx download
cable, a third-party JTAG development system, a
JTAG-compatible board tester, or a simple microprocessor
interface that emulates the JTAG instruction sequence. The
iMPACT software also outputs serial vector format (SVF)
files for use with any tools that accept SVF format, including
automatic test equipment. See CoolRunner-II Application
Notes for more information on how to program.
as well. The internal controllers can operate as fast as 66
MHz.
Table 7: JTAG Instructions
Code
Instruction
Description
00000000
EXTEST
Force boundary scan data onto
outputs
00000011
PRELOAD
11111111
BYPASS
Insert bypass register between
TDI and TDO
00000010
INTEST
Force boundary scan data onto
inputs and feedbacks
00000001
IDCODE
Read IDCODE
In System Programming
All CoolRunner-II CPLD parts are 1.8V in system programmable. This means they derive their programming voltage
and currents from the 1.8V VCC (internal supply voltage)
pins on the part. The VCCIO pins do not participate in this
operation, as they may assume another voltage ranging as
high as 3.3V down to 1.5V. A 1.8V VCC is required to properly operate the internal state machines and charge pumps
that reside within the CPLD to do the nonvolatile programming operations. The JTAG interface buffers are powered
by a dedicated power pin, VCCAUX, which is independent of
all other supply pins. VCCAUX must be connected. Xilinx
software is provided to deliver the bit-stream to the CPLD
and drive the appropriate IEEE 1532 protocol. To that end,
there is a set of IEEE 1532 commands that are supported in
the CoolRunner-II CPLD parts. Programming times are less
than one second for 32 to 256 macrocell parts. Programming times are less than four seconds for 384 and 512 macrocell parts. Programming of CoolRunner-II CPLDs is only
guaranteed when operating in the commercial temperature
and voltage ranges as defined in the device-specific data
sheets.
On-The-Fly Reconfiguration (OTF)
Xilinx ISE 5.2i supports OTF for CoolRunner-II CPLDs. This
permits programming a new nonvolatile pattern into the part
while another pattern is currently in use. OTF has the same
voltage and temperature specifications as system programming. During pattern transition I/O pins are in high impedance with weak pullup to VCCIO. Transition time typically
lasts between 50 and 300 µs, depending on density. See
XAPP388 for more information.
JTAG Instructions
Table 7 shows the commands available to users. These
same commands may be used by third party ATE products,
Latch macrocell data into
boundary scan cells
11111101 USERCODE Read USERCODE
11111100
HIGHZ
Force output into high
impedance state
11111010
CLAMP
Latch present output state
Power-Up Characteristics
CoolRunner-II CPLD parts must operate under the
demands of both the high-speed and the portable market
places, therefore, they must support hot plugging for the
high-speed world and tolerate most any power sequence to
its various voltage pins. They must also not draw excessive
current during power-up initialization. To those ends, the
general behavior is summarized as follows:
1. I/O pins are disabled until the end of power-up.
2. As supply rises, configuration bits transfer from
nonvolatile memory to SRAM cells.
3. As power up completes, the outputs become as
configured (input, output, or I/O).
4. For specific configuration times and power up
requirements, see the device specific data sheet.
CoolRunner-II CPLD I/O pins are well behaved under all
operating conditions. During power-up, CoolRunner-II
devices employ internal circuitry which keeps the devices in
the quiescent state until the VCCINT supply voltage is at a
safe level (approximately 1.3V). In the quiescent state,
JTAG pins are disabled, and all device outputs are disabled
with the pins weakly pulled high, as shown in Table 8. When
the supply voltage reaches a safe level, all user registers
become initialized, and the device is immediately available
for operation, as shown in Figure 12. Best results are
obtained with a smooth VCC rise in less than 4 ms. Final
VCC value should occur within 1 second.
If the device is in the erased state (before any user pattern
is programmed), the device outputs remain disabled with a
weak pull-up. The JTAG pins are enabled to allow the
DS090 (v2.5) June 28, 2005
Product Specification
www.xilinx.com
11
R
CoolRunner-II CPLD Family
device to be programmed at any time. All devices are
shipped in the erased state from the factory.
VCCINT
Applying power to a blank part may result in a higher current
flow as the part initializes. This behavior is normal and may
persist for approximately 2 seconds, depending on the
power supply ramp.
If the device is programmed, the device inputs and outputs
take on their configured states for normal operation. The
JTAG pins are enabled to allow device erasure or
boundary-scan tests at any time.
1.3V
3.8
V
(Typ)
(Typ)
0V
No
Power
Quiescent
State
User Operation
Quiescent
State
No
Power
Initialization Transition of User Array
x382_10
Figure 12: Device Behavior During Power Up
Table 8: I/O Power-Up Characteristics
Device Circuitry
Quiescent State
Erased Device Operation
Valid User Operation
IOB Bus-Hold/Weak Pullup
Weak Pull-up
Weak Pull-up
Bus-Hold/Weak Pullup
Device Outputs
Disabled
Disabled
As Configured
Device Inputs and Clocks
Disabled
Disabled
As Configured
Function Block
Disabled
Disabled
As Configured
JTAG Controller
Disabled
Enabled
Enabled
I/O Banking
CoolRunner-II CPLD XC2C32 and XC2C64 macrocell parts
support a single VCCIO rail that can range from 3.3V down to
1.5V operation. Two VCCIO rails are supported on the
XC2C32A, XC2C64A, 128 and 256 macrocell parts where
outputs on each rail can independently range from 3.3V
down to 1.5V operation. Four VCCIO rails are supported on
the 384 and 512 macrocell parts. Any of the VCCIO rails can
assume any one of the VCCIO values of 1.5V, 1.8V, 2.5V, or
3.3V. Designers should assign input and output voltages to
a bank with VCCIO set at the voltage range of that input or
output voltage. The VCC (internal supply voltage) for a CoolRunner-II CPLD must be maintained within 1.8V ±5% for
correct speed operation and proper in system programming.
Mixed Voltage, Power Sequencing, and
Hot Plugging
As mentioned in I/O Banking, CoolRunner-II CPLD parts
support mixed voltage I/O signals. It is important to assign
signals to an I/O bank with the appropriate I/O voltage. Driving a high voltage into a low voltage bank can result in negative current flow through the power supply pins. The power
12
applied to the VCCIO and VCC pins can occur in any order
and the CoolRunner-II CPLD will not be damaged. For best
results, we recommend that VCCIO be applied before
VCCINT. CoolRunner-II CPLDs can reside on boards where
the board is inserted into a “live” connector (hot plugged)
and the parts will be well-behaved as if powering up in a
standard way.
Development System Support
Xilinx CoolRunner-II CPLDs are supported by all configurations of Xilinx standard release development software as
well as the freely available ISE WebPACK software available from www.xilinx.com. Third party development tools
include synthesis tools from Cadence, Exemplar, Mentor
Graphics, Synplicity, and Synopsys.
ATE Support
Third party ATE development support is available for both
programming and board/chip level testing. Vendors providing this support include Agilent, GenRad, and Teradyne.
Other third party providers are expected to deliver solutions
in the future.
www.xilinx.com
DS090 (v2.5) June 28, 2005
Product Specification
R
CoolRunner-II CPLD Family
Absolute Maximum Ratings(1)
Symbol
Parameter
Min.
Max.
Unit
Supply voltage relative to GND
–0.5
2.0
V
VI(3)
Input voltage relative to GND
–0.5
4.0
V
TJ(4)
Maximum junction temperature
–40
150
°C
TSTR
Storage temperature
–65
150
°C
VCC(2)
Notes:
1. Stresses above those listed may cause malfunction or permanent damage to the device. This is a stress rating only. Functional
operation at these or any other condition above those indicated in the operational and programming specification is not implied.
2. The chip supply voltage should rise monotonically.
3. Maximum DC undershoot below GND must be limited to either 0.5V or 10 mA, whichever is easier to achieve. During transitions, the
device pins may undershoot to –2.0V or overshoot to 4.5 V, provided this over- or undershoot lasts less than 10 ns and with the
forcing current being limited to 200 mA. The I/O voltage may never exceed 4.0V.
4. For soldering guidelines and thermal considerations, see the Device Packaging information on the Xilinx website. For Pb-free
packages, see XAPP427.
Quality and Reliability Parameters
Symbol
Parameter
Min
Max
Units
20
-
Years
TDR
Data retention
NPE
Program/erase cycles (Endurance)
1,000
-
Cycles
VESD
Electrostatic discharge(1)
2,000
-
Volts
Notes:
1. ESD is measured to 2000V using the human body model. Pins exposed to this limit can incur additional leakage current to
a maximum of 10 µA when driven to 3.9V.
Further Reading
http://direct.xilinx.com/bvdocs/appnotes/xapp384.pdf
(DDR SDRAM Interface)
Application Notes
http://direct.xilinx.com/bvdocs/appnotes/xapp387.pdf
(PicoBlaze Microcontroller)
http://direct.xilinx.com/bvdocs/appnotes/xapp375.pdf
(Timing Model)
http://direct.xilinx.com/bvdocs/appnotes/xapp376.pdf
(Logic Engine)
http://direct.xilinx.com/bvdocs/appnotes/xapp377.pdf
(Low Power Design)
http://direct.xilinx.com/bvdocs/appnotes/xapp378.pdf
(Advanced Features)
http://direct.xilinx.com/bvdocs/appnotes/xapp379.pdf
(High Speed Design)
http://direct.xilinx.com/bvdocs/appnotes/xapp380.pdf
(Cross Point Switch)
http://direct.xilinx.com/bvdocs/appnotes/xapp381.pdf
(Demo Board)
http://direct.xilinx.com/bvdocs/appnotes/xapp382.pdf
(I/O Characteristics)
http://direct.xilinx.com/bvdocs/appnotes/xapp383.pdf
(Single Error Correction Double Error Detection)
DS090 (v2.5) June 28, 2005
Product Specification
http://direct.xilinx.com/bvdocs/appnotes/xapp388.pdf
(On the Fly Reconfiguration)
http://direct.xilinx.com/bvdocs/appnotes/xapp389.pdf
(Powering CoolRunner-II)
http://direct.xilinx.com/bvdocs/appnotes/xapp393.pdf
(8051 Microcontroller Interface)
http://direct.xilinx.com/bvdocs/appnotes/xapp394.pdf
(Interfacing with Mobile SDRAM)
http://direct.xilinx.com/bvdocs/appnotes/xapp399.pdf
(Assigning CoolRunner-II VREF Pins)
CoolRunner-II Data Sheets
http://direct.xilinx.com/bvdocs/publications/ds090.pdf
(CoolRunner-II Family Datasheet)
http://direct.xilinx.com/bvdocs/publications/ds091.pdf
(XC2C32 Datasheet)
http://direct.xilinx.com/bvdocs/publications/ds092.pdf
(XC2C64 Datasheet)
www.xilinx.com
13
R
CoolRunner-II CPLD Family
http://direct.xilinx.com/bvdocs/publications/ds093.pdf
(XC2C128 Datasheet)
http://direct.xilinx.com/bvdocs/publications/ds094.pdf
(XC2C256 Datasheet)
http://direct.xilinx.com/bvdocs/publications/ds095.pdf
(XC2C384 Datasheet)
http://direct.xilinx.com/bvdocs/publications/ds096.pdf
(XC2C512 Datasheet)
CoolRunner-II White Papers
http://direct.xilinx.com/bvdocs/whitepapers/wp170.pdf
(Security)
Packages
Package Drawings
Online Store
Xilinx Online Store
Revision History
The following table shows the revision history for this document.
14
Date
Version
Revision
01/03/02
1.0
Initial Xilinx release
07/04/02
1.1
Revisions and updates
07/24/02
1.2
Revisions and updates
09/24/02
1.3
Additions to "Power Characteristics" section
01/28/03
1.4
Addition of the "Further Reading" section
02/26/03
1.5
Multiple minor revisions
03/12/03
1.6
Minor revision to "Quality and Reliability Parameters"
10/09/03
1.7
Update Hewlett-Packard to Agilent, OFR to OTF, and other revisions
01/26/04
1.8
Incorporate links to Data Sheets, Application Notes, and Device Packages
02/26/04
1.9
Change to Power-Up Characteristics, page 11. Change TFIN to TDIN. Add Schmitt-trigger
I/O compatibility information. Added TSOL specification.
05/21/04
2.0
Add XC2C32A and XC2C64A devices.
07/30/04
2.1
Pb-free documentation. Changes to TSU and Fsystem to match individual data sheets.
01/10/05
2.2
Added information about programming options, page 11.
03/07/05
2.3
Changes to Table 1, TPD, TSU, TCO, and FSYSTEM1. Removed link to obsolete White Paper.
Modifications to Table 5, IOSTANDARDs. Added Table 2, DC Characteristics.
04/15/05
2.4
Change to FSYSTEM1 for XC2C128.
06/28/05
2.5
Move to Product Specification
www.xilinx.com
DS090 (v2.5) June 28, 2005
Product Specification