k 0 XC9500XL High-Performance CPLD Family Data Sheet R DS054 (v2.5) May 22, 2009 0 0 Product Specification Features • • Optimized for high-performance 3.3V systems - 5 ns pin-to-pin logic delays, with internal system frequency up to 208 MHz - Small footprint packages including VQFPs, TQFPs and CSPs (Chip Scale Package) - Pb-free available for all packages - Lower power operation - 5V tolerant I/O pins accept 5V, 3.3V, and 2.5V signals - 3.3V or 2.5V output capability - Advanced 0.35 micron feature size CMOS FastFLASH technology Advanced system features • - Local clock inversion with three global and one product-term clocks - Individual output enable per output pin with local inversion - Input hysteresis on all user and boundary-scan pin inputs - Bus-hold circuitry on all user pin inputs - Supports hot-plugging capability - Full IEEE Std 1149.1 boundary-scan (JTAG) support on all devices Four pin-compatible device densities - 36 to 288 macrocells, with 800 to 6400 usable gates • Fast concurrent programming • Slew rate control on individual outputs • Enhanced data security features • Excellent quality and reliability - In-system programmable - Superior pin-locking and routability with FastCONNECT II switch matrix - Extra wide 54-input Function Blocks - 10,000 program/erase cycles endurance rating - Up to 90 product-terms per macrocell with individual product-term allocation - 20 year data retention • Pin-compatible with 5V core XC9500 family in common package footprints Table 1: XC9500XL Device Family XC9536XL XC9572XL XC95144XL XC95288XL Macrocells 36 72 144 288 Usable Gates 800 1,600 3,200 6,400 Registers 36 72 144 288 TPD (ns) 5 5 5 6 TSU (ns) 3.7 3.7 3.7 4.0 TCO (ns) 3.5 3.5 3.5 3.8 fSYSTEM (MHz) 178 178 178 208 © 1998–2009 Xilinx, Inc. XILINX, the Xilinx logo, Virtex, Spartan, ISE, and other designated brands included herein are trademarks of Xilinx in the United States and other countries. All other trademarks are the property of their respective owners. DS054 (v2.5) May 22, 2009 Product Specification www.xilinx.com 1 R XC9500XL High-Performance CPLD Family Data Sheet Table 2: XC9500XL Packages and User I/O Pins (not including 4 dedicated JTAG pins) Package(1) XC9536XL XC9572XL XC95144XL XC95288XL PC44 34 34 - - PCG44 34 34 VQ44 34 34 - - VQG44 34 34 CS48 36 38 - - CSG48 36 38 VQ64 36 52 - - VQG64 36 52 TQ100 - 72 81 - 72 81 - 117 TQG100 CS144 - CSG144 TQ144 117 - - TQG144 PQ208 - - 117 117 117 117 - 168 PQG208 BG256 168 - - - BGG256 FG256 192 192 - - - FGG256 CS280 - 192 192 - - CSG280 - 192 192 Notes: 1. The letter "G" as the third character indicates a Pb-free package. DS054 (v2.5) May 22, 2009 Product Specification www.xilinx.com 2 R XC9500XL High-Performance CPLD Family Data Sheet 3 JTAG Port JTAG Controller In-System Programming Controller 54 Function Block 1 18 I/O Macrocells 1 to 18 I/O FastCONNECT II Switch Matrix I/O I/O I/O Blocks I/O I/O I/O 54 Function Block 2 18 Macrocells 1 to 18 54 Function Block 3 18 Macrocells 1 to 18 I/O 3 I/O/GCK 54 1 18 I/O/GSR 2 or 4 I/O/GTS Function Block N Macrocells 1 to 18 DS054_01_042001 Figure 1: XC9500XL Architecture Note: Function block outputs (indicated by the bold lines) drive the I/O blocks directly. Family Overview The FastFLASH XC9500XL family is a 3.3V CPLD family targeted for high-performance, low-voltage applications in leading-edge communications and computing systems, where high device reliability and low power dissipation is important. Each XC9500XL device supports in-system programming (ISP) and the full IEEE Std 1149.1 (JTAG) boundary-scan, allowing superior debug and design iteration capability for small form-factor packages. The XC9500XL family is designed to work closely with the Xilinx® Virtex®, Spartan®-XL and XC4000XL FPGA families, allowing system designers to partition logic optimally between fast interface circuitry and high-density general purpose logic. As shown in Table 1, logic density of the XC9500XL devices ranges from 800 to 6400 usable gates with 36 to 288 registers, respectively. Multiple package options and associated DS054 (v2.5) May 22, 2009 Product Specification I/O capacity are shown in Table 2. The XC9500XL family members are fully pin-compatible, allowing easy design migration across multiple density options in a given package footprint. The XC9500XL architectural features address the requirements of in-system programmability. Enhanced pin-locking capability avoids costly board rework. In-system programming throughout the full commercial operating range and a high programming endurance rating provide worry-free reconfigurations of system field upgrades. Extended data retention supports longer and more reliable system operating life. Advanced system features include output slew rate control and user-programmable ground pins to help reduce system noise. Each user pin is compatible with 5V, 3.3V, and 2.5V inputs, and the outputs may be configured for 3.3V or 2.5V www.xilinx.com 3 R XC9500XL High-Performance CPLD Family Data Sheet Function Block operation. The XC9500XL device exhibits symmetric full 3.3V output voltage swing to allow balanced rise and fall times. Additional details can be found in the application notes listed in "Further Reading" on page 17. Each Function Block, as shown in Figure 2 is comprised of 18 independent macrocells, each capable of implementing a combinatorial or registered function. The FB also receives global clock, output enable, and set/reset signals. The FB generates 18 outputs that drive the FastCONNECT switch matrix. These 18 outputs and their corresponding output enable signals also drive the IOB. Architecture Description Each XC9500XL device is a subsystem consisting of multiple Function Blocks (FBs) and I/O Blocks (IOBs) fully interconnected by the FastCONNECT II switch matrix. The IOB provides buffering for device inputs and outputs. Each FB provides programmable logic capability with extra wide 54inputs and 18 outputs. The FastCONNECT II switch matrix connects all FB outputs and input signals to the FB inputs. For each FB, up to 18 outputs (depending on package pin-count) and associated output enable signals drive directly to the IOBs. See Figure 1. Logic within the FB is implemented using a sum-of-products representation. Fifty-four inputs provide 108 true and complement signals into the programmable AND-array to form 90 product terms. Any number of these product terms, up to the 90 available, can be allocated to each macrocell by the product term allocator. Macrocell 1 Programmable AND-Array From FastCONNECT II Switch Matrix Product Term Allocators 18 54 18 18 To FastCONNECT II Switch Matrix OUT To I/O Blocks PTOE Macrocell 18 1 3 Global Global Set/Reset Clocks DS054_02_042101 Figure 2: XC9500XL Function Block Macrocell Each XC9500XL macrocell may be individually configured for a combinatorial or registered function. The macrocell and associated FB logic is shown in Figure 3. Five direct product terms from the AND-array are available for use as primary data inputs (to the OR and XOR gates) to implement combinatorial functions, or as control inputs including clock, clock enable, set/reset, and output enable. The product term allocator associated with each macrocell selects how the five direct terms are used. DS054 (v2.5) May 22, 2009 Product Specification The macrocell register can be configured as a D-type or T-type flip-flop, or it may be bypassed for combinatorial operation. Each register supports both asynchronous set and reset operations. During power-up, all user registers are initialized to the user-defined preload state (default to 0 if unspecified). www.xilinx.com 4 R XC9500XL High-Performance CPLD Family Data Sheet 54 Global Set/Reset Global Clocks 3 Additional Product Terms (from other macrocells) Product Term Set 1 0 To FastCONNECTII Switch Matrix S D/T Q Product Term Allocator CE Product Term Clock Enable R Product Term Clock Product Term Reset OUT Product Term OE PTOE To I/O Blocks Additional Product Terms (from other macrocells) DS054_03_042101 Figure 3: XC9500XL Macrocell Within Function Block All global control signals are available to each individual macrocell, including clock, set/reset, and output enable signals. As shown in Figure 4, the macrocell register clock originates from either of three global clocks or a product term clock. Both true and complement polarities of the selected clock source can be used within each macrocell. A GSR input is also provided to allow user registers to be set to a user-defined state. DS054 (v2.5) May 22, 2009 Product Specification www.xilinx.com 5 R XC9500XL High-Performance CPLD Family Data Sheet Macrocell Product Term Set S D/T CE Product Term Clock R Product Term Reset I/O/GSR Global Set/Reset I/O/GCK1 Global Clock 1 I/O/GCK2 Global Clock 2 I/O/GCK3 Global Clock 3 DS054_04_052209 Figure 4: Macrocell Clock and Set/Reset Capability DS054 (v2.5) May 22, 2009 Product Specification www.xilinx.com 6 R XC9500XL High-Performance CPLD Family Data Sheet Product Term Allocator The product term allocator controls how the five direct product terms are assigned to each macrocell. For example, all five direct terms can drive the OR function as shown in Figure 5. Note that the incremental delay affects only the product terms in other macrocells. The timing of the direct product terms is not changed. Product Term Allocator Product Term Allocator Macrocell Product Term Logic Product Term Allocator DS054_05_042101 Figure 5: Macrocell Logic Using Direct Product Term The product term allocator can re-assign other product terms within the FB to increase the logic capacity of a macrocell beyond five direct terms. Any macrocell requiring additional product terms can access uncommitted product terms in other macrocells within the FB. Up to 15 product terms can be available to a single macrocell with only a small incremental delay of tPTA, as shown in Figure 6. Macrocell Logic With 15 Product Terms Product Term Allocator DS054_06_042101 Figure 6: Product Term Allocation With 15 Product Terms DS054 (v2.5) May 22, 2009 Product Specification www.xilinx.com 7 R XC9500XL High-Performance CPLD Family Data Sheet The product term allocator can re-assign product terms from any macrocell within the FB by combining partial sums of products over several macrocells, as shown in Figure 7. In this example, the incremental delay is only 2*TPTA. All 90 product terms are available to any macrocell, with a maximum incremental delay of 8*TPTA. Product Term Allocator Macrocell Logic With 2 Product Terms Product Term Allocator Product Term Allocator Macrocell Logic With 18 Product Terms Product Term Allocator DS054_07 _042101 Figure 7: Product Term Allocation Over Several Macrocells DS054 (v2.5) May 22, 2009 Product Specification www.xilinx.com 8 R XC9500XL High-Performance CPLD Family Data Sheet The internal logic of the product term allocator is shown in Figure 8. From Upper Macrocell To Upper Macrocell Product Term Allocator Product Term Set Global Set/Reset 1 0 S D/T Q CE Global Clocks R Product Term Clock Product Term Reset Global Set/Reset Product Term OE From Lower Macrocell To Lower Macrocell DS054_08_042101 Figure 8: Product Term Allocator Logic DS054 (v2.5) May 22, 2009 Product Specification www.xilinx.com 9 R XC9500XL High-Performance CPLD Family Data Sheet FastCONNECT II Switch Matrix The FastCONNECT II Switch Matrix connects signals to the FB inputs, as shown in Figure 9. All IOB outputs (corre- FastCONNECT II Switch Matrix sponding to user pin inputs) and all FB outputs drive the FastCONNECT II matrix. Any of these (up to a fan-in limit of 54) may be selected to drive each FB with a uniform delay. Function Block I/O Block (54) 18 D/T Q I/O Function Block I/O Block (54) 18 D/T Q I/O DS054_09_042101 Figure 9: FastCONNECT II Switch Matrix DS054 (v2.5) May 22, 2009 Product Specification www.xilinx.com 10 R XC9500XL High-Performance CPLD Family Data Sheet I/O Block The I/O Block (IOB) interfaces between the internal logic and the device user I/O pins. Each IOB includes an input buffer, output driver, output enable selection multiplexer, and user programmable ground control. See Figure 10 for details. To other Macrocells I/O Block To FastCONNECT Switch Matrix Macrocell Bus-Hold I/O OUT (Inversion in AND-array) Product Term OE 1 PTOE UserProgrammable Ground 0 Slew Rate Control I/O/GTS1 Global OE 1 I/O/GTS2 Global OE 2 I/O/GTS3 Global OE 3 I/O/GTS4 Global OE 4 Available in XC95144XL and XC95288XL DS054_10_042101 Figure 10: I/O Block and Output Enable Capability The input buffer is compatible with 5V CMOS, 5V TTL, 3.3V CMOS, and 2.5V CMOS signals. The input buffer uses the internal 3.3V voltage supply (VCCINT) to ensure that the input thresholds are constant and do not vary with the DS054 (v2.5) May 22, 2009 Product Specification VCCIO voltage. Each input buffer provides input hysteresis (50 mV typical) to help reduce system noise for input signals with slow rise or fall edges. www.xilinx.com 11 R XC9500XL High-Performance CPLD Family Data Sheet Each output driver is designed to provide fast switching with minimal power noise. All output drivers in the device may be configured for driving either 3.3V CMOS levels (which are compatible with 5V TTL levels as well) or 2.5V CMOS levels by connecting the device output voltage supply (VCCIO) to a 3.3V or 2.5V voltage supply. Figure 11 shows how the XC9500XL device can be used in 3.3V only systems and mixed voltage systems with any combination of 5V, 3.3V and 2.5V power supplies. Each output driver can also be configured for slew-rate limited operation. Output edge rates may be slowed down to reduce system noise (with an additional time delay of tSLEW) under user control. See Figure 12. The output enable may be generated from one of four options: a product term signal from the macrocell, any of the global output enable signals (GTS), always “1,” or always “0.” There are two global output enables for devices with 72 or fewer macrocells, and four global output enables for devices with 144 or more macrocells. Any selected output enable signal may be inverted locally at each pin output to provide maximal design flexibility. Each IOB provides user programmable ground pin capability. This allows device I/O pins to be configured as additional ground pins in order to force otherwise unused pins to a low 5V CMOS voltage state, as well as provide for additional device grounding capability. This grounding of the pin is achieved by internal logic that forces a logic low output regardless of the internal macrocell signal, so the internal macrocell logic is unaffected by the programmable ground pin capability. Each IOB also provides for bus-hold circuitry (also called a “keeper”) that is active during valid user operation. The bus-hold feature eliminates the need to tie unused pins either high or low by holding the last known state of the input until the next input signal is present. The bus-hold circuit drives back the same state via a nominal resistance (RBH) of 50 kΩ. See Figure 13. Note the bus-hold output will drive no higher than VCCIO to prevent overdriving signals when interfacing to 2.5V components. When the device is not in valid user operation, the bus-hold circuit defaults to an equivalent 50 kΩ pull-up resistor in order to provide a known repeatable device state. This occurs when the device is in the erased state, in programming mode, in JTAG INTEST mode, or during initial power-up. A pull-down resistor (1 kΩ) may be externally added to any pin to override the default RBH resistance to force a low state during power-up or any of these other modes. 5V CMOS 5V 5V 3.3V 0V 0V 5V TTL or VCCINT 5V TTL or VCCIO 5V 3.3V 2.5V VCCINT VCCIO 5V XC9500XL CPLD IN OUT 0V 3.3V CMOS or 2.5V CMOS 3.3V CMOS, 5V TTL 0V 3.3V 3.3V CMOS or IN XC9500XL CPLD OUT 0V 0V 3.3V 2.5V 3.3V 0V 0V GND 2.5V CMOS 2.5V CMOS 2.5V GND 2.5V 0V 0V (a) (b) DS054_11_042101 Figure 11: XC9500XL Devices in (a) 3.3V only and (b) Mixed 5V/3.3V/2.5V Systems 5V Tolerant I/Os The I/Os on each XC9500XL device are fully 5V tolerant even though the core power supply is 3.3 volts. This allows 5V CMOS signals to connect directly to the XC9500XL inputs without damage. The 3.3V VCCINT power supply must be at least 1.5V before 5V signals are applied to the I/Os. In mixed 3.3V/2.5V systems, the user pins, the core power supply (VCCINT), and the output power supply (VCCIO) may have power applied in any order. DS054 (v2.5) May 22, 2009 Product Specification Xilinx proprietary ESD circuitry and high impedance initial state permit hot plugging cards using these devices. Pin-Locking Capability The capability to lock the user defined pin assignments during design iteration depends on the ability of the architecture to adapt to unexpected changes. The XC9500XL devices incorporate architectural features that enhance the ability to accept design changes while maintaining the same pinout. www.xilinx.com 12 R XC9500XL High-Performance CPLD Family Data Sheet The XC9500XL architecture provides for superior pin-locking characteristics with a combination of large number of routing switches in the FastCONNECT II switch matrix, a 54-wide input Function Block, and flexible, bidirectional product term allocation within each macrocell. These features address design changes that require adding or changing internal routing, including additional signals into existing equations, or increasing equation complexity, respectively. Output Voltage Output Voltage VCCIO For extensive design changes requiring higher logic capacity than is available in the initially chosen device, the new design may be able to fit into a larger pin-compatible device using the same pin assignments. The same board may be used with a higher density device without the expense of board rework. Standard Slew-Rate Limited Slew-Rate Limited TSLEW TSLEW 1.5V 1.5V Standard Time 0 Time 0 (b) (a) DS054_12_042101 Figure 12: Output Slew-Rate Control For (a) Rising and (b) Falling Outputs Set to PIN during valid user operation download cable, a third-party JTAG development system, JTAG-compatible board tester, or a simple microprocessor interface that emulates the JTAG instruction sequence. Drive to VCCIO Level All I/Os are 3-stated and pulled high by the bus-hold circuitry during in-system programming. If a particular signal must remain low during this time, then a pull-down resistor may be added to the pin. 0 PIN RBH External Programming I/O DS054_13_042101 Reliability and Endurance Figure 13: Bus-Hold Logic In-System Programming WARNING: Programming temperature range of TA = 0° C to +70° C One or more XC9500XL devices can be daisy chained together and programmed in-system via a standard 4-pin JTAG protocol, as shown in Figure 14. In-system programming offers quick and efficient design iterations and eliminates package handling. The Xilinx development system provides the programming data sequence using a Xilinx DS054 (v2.5) May 22, 2009 Product Specification XC9500XL devices can also be programmed by the Xilinx HW-130 device programmer as well as third-party programmers. This provides the added flexibility of using pre-programmed devices during manufacturing, with an in-system programmable option for future enhancements and design changes. All XC9500XL CPLDs provide a minimum endurance level of 10,000 in-system program/erase cycles and a minimum data retention of 20 years. Each device meets all functional, performance, and data retention specifications within this endurance limit. IEEE Std 1149.1 Boundary-Scan (JTAG) XC9500XL devices fully support IEEE Std 1149.1 boundary-scan (JTAG). EXTEST, SAMPLE/PRELOAD, BYPASS, USERCODE, INTEST, IDCODE, HIGHZ and CLAMP www.xilinx.com 13 R XC9500XL High-Performance CPLD Family Data Sheet instructions are supported in each device. Additional instructions are included for in-system programming operations. Design Security JTAG pins are subject to noise, such as during system power-up. Once set, the write-protection may be deactivated when the device needs to be reprogrammed with a valid pattern with a specific sequence of JTAG instructions. Table 3: Data Security Options The read security bits can be set by the user to prevent the internal programming pattern from being read or copied. When set, they also inhibit further program operations but allow device erase. Erasing the entire device is the only way to reset the read security bit. Read Security Write Security XC9500XL devices incorporate advanced data security features which fully protect the programming data against unauthorized reading or inadvertent device erasure/reprogramming. Table 3 shows the four different security settings available. Default Set The write security bits provide added protection against accidental device erasure or reprogramming when the Default Set Read Allowed Read Inhibited Program/Erase Allowed Program Inhibited Erase Allowed Read Allowed Read Inhibited Program/Erase Allowed Program/Erase Inhibited V CC GND (a) (b) DS054_14_052209 Figure 14: System Programming Operation (a) Solder Device to PCB and (b) Program Using Download Cable Low Power Mode Timing Model All XC9500XL devices offer a low-power mode for individual macrocells or across all macrocells. This feature allows the device power to be significantly reduced. The uniformity of the XC9500XL architecture allows a simplified timing model for the entire device. The basic timing model, shown in Figure 15, is valid for macrocell functions that use the direct product terms only, with standard power setting, and standard slew rate setting. Table 4 shows how each of the key timing parameters is affected by the product term allocator (if needed), low-power setting, and slew-limited setting. Each individual macrocell may be programmed in low-power mode by the user. Performance-critical parts of the application can remain in standard power mode, while other parts of the application may be programmed for low-power operation to reduce the overall power dissipation. Macrocells programmed for low-power mode incur additional delay (tLP) in pin-to-pin combinatorial delay as well as register setup time. Product term clock to output and product term output enable delays are unaffected by the macrocell power-setting. Signals switching at rates less than 50 ns rise/fall time should be assigned to the macrocells configured in low power mode. DS054 (v2.5) May 22, 2009 Product Specification The product term allocation time depends on the logic span of the macrocell function, which is defined as one less than the maximum number of allocators in the product term path. If only direct product terms are used, then the logic span is 0. The example in Figure 6 shows that up to 15 product terms are available with a span of 1. In the case of Figure 7, the 18 product term function has a span of 2. www.xilinx.com 14 R XC9500XL High-Performance CPLD Family Data Sheet Detailed timing information may be derived from the full timing model shown in Figure 16. The values and explanations for each parameter are given in the individual device data sheets. Combinatorial Logic Combinatorial Logic D/T Q TCO Clock to Out Time = TCO Setup Time = TSU (b) Propagation Delay = TPD (a) TPSU Combinatorial Logic D/T Q Combinatorial Logic P-Term Clock Path D/T Q TPCO Setup Time = TPSU Clock to Out Time = TPCO (c) Internal System Cycle Time = TSYSTEM (d) DS054_15_042101 Figure 15: Basic Timing Model TF TLOGILP TIN TLOGI TPTCK S*TPTA TSLEW TPDI D/T Q CE TAOI TRAI TGCK TPTSR TOUT TSUI TCOI THI TEN SR TGSR TPTTS Macrocell TGTS DS054_16_042101 Figure 16: Detailed Timing Model DS054 (v2.5) May 22, 2009 Product Specification www.xilinx.com 15 R XC9500XL High-Performance CPLD Family Data Sheet Power-Up Characteristics During power-up, the XC9500XL device I/Os may be undefined until VCCINT rises above 1 Volt. This time period is called the subthreshold region, as transistors have not yet fully turned on. If VCCIO is powered before or simultaneously with VCCINT, I/Os may drive during this voltage transition range. If VCCIO is powered after VCCINT has passed through the subthreshold region, I/Os will be in 3-state with a weak pull-up until VCCINT reaches the threshold of the User Operation state (approximately 2.5V). When VCCINT reaches this point, user registers are initialized (typically within 200 μs) after which I/Os will assume the behavior determined by the user pattern, as shown in Figure 17. ABEL), and simulation capabilities. It supports the XC9500XL family as well as other CPLD and FPGA families. The Alliance Series includes CPLD and FPGA implementation technology as well as all necessary libraries and interfaces for Alliance partner EDA solutions. FastFLASH Technology An advanced 0.35 micron feature size CMOS Flash process is used to fabricate all XC9500XL devices. The FastFLASH process provides high performance logic capability, fast programming times, and superior reliability and endurance ratings. If the device is in the erased state (before any user pattern is programmed), the device outputs remain disabled with weak pull-up. The JTAG pins are enabled to allow the device to be programmed at any time. All devices are shipped in the erased state from the factory. VCCINT 2.5V 3.8 V (Typ) (Typ) If the device is programmed, the device inputs and outputs take on their configured states for normal operation. The JTAG pins are enabled to allow device erasure or boundary-scan tests at any time. 1.0V 0V No Power Development System Support The XC9500XL family and associated in-system programming capabilities are fully supported in either software solutions available from Xilinx. Subthreshold State User Operation Quiescent State No Power Initialization of User Registers Quiescent State DS054_17_042101 Figure 17: Device Behavior During Power-up The Foundation Series is an all-in-one development system containing schematic entry, HDL (VHDL, Verilog, and Table 4: Timing Model Parameters Parameter Description Product Term Allocator(1) Macrocell Low-Power Setting Output Slew-Limited Setting TPD Propagation Delay + TPTA * S + TLP + TSLEW TSU Global Clock Setup Time + TPTA * S + TLP – TCO Global Clock-to-output - - + TSLEW TPSU Product Term Clock Setup Time + TPTA * S + TLP - TPCO Product Term Clock-to-output - - + TSLEW TSYSTEM Internal System Cycle Period + TPTA * S + TLP - Notes: 1. S = the logic span of the function, as defined in the text. Table 5: XC9500XL Pin Characteristics Subthreshold State Quiescent State Erased Device Operation Valid User Operation IOB Bus-Hold Undetermined Pull-up Pull-up Bus-Hold Device I/O and Clocks Undetermined Disabled Disabled As Configured JTAG Controller Undetermined Disabled Enabled Enabled Device Circuitry DS054 (v2.5) May 22, 2009 Product Specification www.xilinx.com 16 R XC9500XL High-Performance CPLD Family Data Sheet Further Reading Further information on the XC9500XL CPLD family can be found at: http://www.xilinx.com/support/documentation/xc9500xl.htm. This site includes: • Pinouts contained in the density-specific data sheets • Package electrical and thermal characteristics in UG112, Device Package User Guide • Termination, logic thresholds, power sequencing, and slew rate information in UG445, CPLD IO User Guide • Timing model in XAPP111, Using the XC9500XL Timing Model • Good design practices in XAPP784, Bulletproof CPLD Design Practices • Package drawings and dimensions at http://www.xilinx.com/support/documentation/package_specifications.htm Revision History The following table shows the revision history for this document. Date Version 09/28/98 1.0 Initial Xilinx release. 10/02/98 1.1 Figure 1 correction. 02/03/99 1.2 Included hot socket reference; revised layout; BGA package change for XC95288XL. 04/02/99 1.3 Minor typesetting corrections. 06/07/99 1.4 Minor typesetting corrections. 06/07/99 1.5 Added CS280 package. 01/25/02 1.6 Added DS054 data sheet number. Added 44-pin VQFP package. Updated Device Family table. 02/07/03 1.7 Added "Further Reading" section. 08/02/04 1.8 Added Pb-free documentation. 11/11/04 1.9 Changes to package designations in Table 2 on page 2. 07/15/05 2.0 Move to Product Specification. 03/22/06 2.1 Add Warranty Disclaimer. 07/25/06 2.2 Added Subthreshold State to Figure 17 and Table 5, page 16. 04/03/07 2.3 Added warning on programming temperature range, page 13. 11/20/08 2.4 Updated "Further Reading" section. 05/22/09 2.5 Updated description of power sequencing for 5V tolerance in "5V Tolerant I/Os" section. DS054 (v2.5) May 22, 2009 Product Specification Revision www.xilinx.com 17 R XC9500XL High-Performance CPLD Family Data Sheet Notice of Disclaimer THE XILINX HARDWARE FPGA AND CPLD DEVICES REFERRED TO HEREIN (“PRODUCTS”) ARE SUBJECT TO THE TERMS AND CONDITIONS OF THE XILINX LIMITED WARRANTY WHICH CAN BE VIEWED AT http://www.xilinx.com/warranty.htm. THIS LIMITED WARRANTY DOES NOT EXTEND TO ANY USE OF PRODUCTS IN AN APPLICATION OR ENVIRONMENT THAT IS NOT WITHIN THE SPECIFICATIONS STATED IN THE XILINX DATA SHEET. ALL SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE. PRODUCTS ARE NOT DESIGNED OR INTENDED TO BE FAIL-SAFE OR FOR USE IN ANY APPLICATION REQUIRING FAIL-SAFE PERFORMANCE, SUCH AS LIFE-SUPPORT OR SAFETY DEVICES OR SYSTEMS, OR ANY OTHER APPLICATION THAT INVOKES THE POTENTIAL RISKS OF DEATH, PERSONAL INJURY, OR PROPERTY OR ENVIRONMENTAL DAMAGE (“CRITICAL APPLICATIONS”). USE OF PRODUCTS IN CRITICAL APPLICATIONS IS AT THE SOLE RISK OF CUSTOMER, SUBJECT TO APPLICABLE LAWS AND REGULATIONS. DS054 (v2.5) May 22, 2009 Product Specification www.xilinx.com 18