ZARLINK MT88E45B

MT88E45
4-Wire Calling Number Identification
Circuit 2 (4-Wire CNIC2)
Data Sheet
Features
•
August 2005
Compatible with:
Ordering Information
•
Bellcore GR-30-CORE, SR-TSV-002476,
ANSI/TIA/EIA-716, TIA/EIA-777;
•
ETSI ETS 300 778-1 (FSK only variant) & -2;
•
BT (British Telecom) SIN227 & SIN242
•
Bellcore ‘CPE Alerting Signal’ (CAS), ETSI ‘Dual
Tone Alerting Signal’ (DT-AS), BT Idle State and
Loop State ‘Tone Alert Signal’ detection
•
1200 baud Bell 202 and CCITT V.23 FSK
demodulation
•
Separate differential input amplifiers with
adjustable gain for Tip/Ring and telephone hybrid
or speech IC connections
MT88E45BN
MT88E45BS
MT88E45BSR
MT88EBNR
MT88E45BN1
MT88E45BNR1
*Pb
20 Pin SSOP
20 Pin SOIC
20 Pin SOIC
20 Pin SSOP
20 Pin SSOP*
20 Pin SSOP*
Free Matte Tin
Tubes
Tubes
Tape & Reel
Tape & Reel
Tubes
Tape & Reel
-40°C to +85°C
Applications
•
Bellcore CID (Calling Identity Delivery) and
CIDCW (Calling Identity Delivery on Call Waiting)
telephones and adjuncts
•
ETSI, BT CLIP (Calling Line Identity Presentation)
and CLIP with Call Waiting telephones and
adjuncts
•
Selectable 3-wire FSK data interface (bit stream
or 1 byte buffer)
•
Facility to monitor the stop bit for framing error
check
•
FSK Carrier detect status output
•
Fax and answering machines
•
3 to 5V +/- 10% supply voltage
•
Computer Telephony Integration (CTI) systems
•
Uses 3.579545 MHz crystal or ceramic resonator
•
Low power CMOS with power down
MODE
FSKen+Tip/Ring CASen
+
IN1-
-
Anti-Alias
Filter
PWDN
GS1
+
IN2-
-
Carrier
Detector
Hybrid CASen
PWDN
MODE
Bias
Generator
PWDN
FSKen
OSC2
2130Hz
Bandpass
CASen
Control Bit
Decode
Oscillator
OSC1
DATA
Data Timing
Recovery
DCLK
FSKen
CASen
GS2
VREF
FSK
Demodulator
PWDN
PWDN
IN2+
FSK
Bandpass
2750Hz
Bandpass
CD
DR
STD
Tone
Detection
Algorithm
Mux
IN1+
Guard
Time
CASen
CB0 CB1 CB2
Figure 1 - Functional Block Diagram
1
Zarlink Semiconductor Inc.
Zarlink, ZL and the Zarlink Semiconductor logo are trademarks of Zarlink Semiconductor Inc.
Copyright 2001-2005, Zarlink Semiconductor Inc. All Rights Reserved.
DR/STD
ST/GT
EST
Vdd
Vss
MT88E45
Data Sheet
Description
The MT88E45B is a low power CMOS integrated circuit suitable for receiving the physical layer signals used in
North American (Bellcore) Calling Identity Delivery on Call Waiting (CIDCW) and Calling Identity Delivery (CID)
services. It is also suitable for ETSI and BT Calling Line Identity Presentation (CLIP) and CLIP with Call Waiting
services.
The MT88E45B contains a 1200 baud Bell 202/CCITT V.23 FSK demodulator and a CAS/DT-AS detector. Two
input op-amps allow the MT88E45B to be connected to both Tip/Ring and the telephone hybrid or speech IC
receive pair for optimal CIDCW telephone architectural implementation. FSK demodulation is always on Tip/Ring,
while CAS detection can be on Tip/Ring or Hybrid Receive. Tip/Ring CAS detection is required for the Bellcore/TIA
Multiple Extension Interworking (MEI) and BT’s on-hook CLIP. A selectable FSK data interface allows the data to be
processed as a bit stream or extracted from a 1 byte on chip buffer. Power management has been incorporated to
power down the FSK or CAS section when not required. Full chip power down is also available. The MT88E45B is
suitable for applications using a fixed power source (with a +/-10% variation) between 3 and 5 V.
2
Zarlink Semiconductor Inc.
MT88E45
VREF
1
IN1+
2
IN1-
Data Sheet
20
IN2+
19
IN2-
3
18
GS2
GS1
4
17
CB2
Vss
5
16
CB1
OSC1
6
15
Vdd
OSC2
7
14
CD
CB0
8
13
ST/GT
DCLK
9
12
EST
DATA
10
11
DR/STD
MT88E45B
Figure 2 - Pin Connections
Pin Description
Pin # Name
Description
1
VREF
Voltage Reference (Output). Nominally Vdd/2. It is used to bias the Tip/Ring and Hybrid input opamps.
2
IN1+
Tip/Ring Op-amp Non-inverting (Input).
3
IN1-
Tip/Ring Op-amp Inverting (Input).
4
GS1
Tip/Ring Gain Select (Output). This is the output of the Tip/Ring connection op-amp. The opamp should be used to connect the MT88E45B to Tip and Ring. The Tip/Ring signal can be
amplified or attenuated at GS1 via selection of the feedback resistor between GS1 and IN1-. FSK
demodulation (which is always on Tip/Ring) or CAS detection (for MEI or BT on-hook CLIP) of the
GS1 signal is enabled via the CB1 and CB2 pins. See Tables 1 and 2.
5
Vss
Power supply ground.
6
OSC1 Oscillator (Input). Crystal connection. This pin can also be driven directly from an external clock
source.
7
OSC2 Oscillator (Output). Crystal connection. When OSC1 is driven by an external clock, this pin
should be left open.
8
9
CB0
Control Bit 0 (CMOS Input). This pin is used primarily to select the 3-wire FSK data interface
mode. When it is low, interface mode 0 is selected where the FSK bit stream is output directly.
When it is high, interface mode 1 is selected where the FSK byte is stored in a 1 byte buffer which
can be read serially by the application’s microcontroller.
The FSK interface is consisted of the DATA, DCLK and DR/STD pins. See the 3 pin descriptions
to understand how CB0 affects the FSK interface.
When CB0 is high and CB1, CB2 are both low the MT88E45B is put into a power down state
consuming minimal power supply current. See Tables 1 and 2.
DCLK 3-wire FSK Interface Data Clock (Schmitt Input/CMOS Output). In mode 0 (when the CB0 pin
is logic low) this is a CMOS output which denotes the nominal mid-point of a FSK data bit.
In mode 1 (when the CB0 pin is logic high) this is a Schmitt trigger input used to shift the FSK data
byte out to the DATA pin.
3
Zarlink Semiconductor Inc.
MT88E45
Data Sheet
Pin Description
Pin # Name
10
11
12
13
DATA
Description
3-wire FSK Interface Data (CMOS Output). Mark frequency corresponds to logical 1. Space
frequency corresponds to logical 0.
In mode 0 (when the CB0 pin is logic low) the FSK serial bit stream is output to the DATA pin
directly.
In mode 1 (when the CB0 pin is logic high) the start bit is stripped off, the data byte and the trailing
stop bit are stored in a 9 bit buffer. At the end of each word signalled by the DR/STD pin, the
microcontroller should shift the byte out onto the DATA pin by applying 8 read pulses to the DCLK
pin. A 9th DCLK pulse will shift out the stop bit for framing error checking.
DR/STD 3-wire FSK Interface Data Ready/CAS Detection Delayed Steering (CMOS Output). Active
low.
When FSK demodulation is enabled via the CB1 and CB2 pins this pin is the Data Ready output.
It denotes the end of a word. In both FSK interface modes 0 and 1, it is normally hi and goes low
for half a bit time at the end of a word. But in mode 1 if DCLK starts during DR low, the first rising
edge of the DCLK input will return DR to high. This feature allows an interrupt requested by a low
going DR to be cleared upon reading the first DATA bit.
When CAS detection is enabled via the CB1 and CB2 pins this pin is the Delayed Steering output.
It goes low to indicate that a time qualified CAS has been detected.
EST
CAS Detection Early Steering (CMOS Output). Active high. This pin is the raw CAS detection
output. It goes high to indicate the presence of a signal meeting the CAS accept frequencies and
signal level. It is used in conjunction with the ST/GT pin and external components to time qualify
the detection to determine whether the signal is a real CAS.
ST/GT CAS Detection Steering/Guard Time (CMOS Output/Analog Input). It is used in conjunction
with the EST pin and external components to time qualify the detection to determine whether the
signal is a real CAS.
A voltage greater than VTGt at this pin causes the MT88E45B to indicate that a CAS has been
detected by asserting the DR/STD pin low. A voltage less than VTGt frees up the MT88E45B to
accept a new CAS and returns DR/STD to high.
14
CD
Carrier Detect (CMOS Output). Active low.
A logic low indicates that an FSK signal is present. A time hysteresis is provided to allow for
momentary signal discontinuity. The demodulated FSK data is ignored by the MT88E45B until
carrier detect has been activated.
15
Vdd
Positive power supply.
16
CB1
Control Bit 1 (CMOS Input). Together with CB2 this pin selects the MT88E45B’s functionality
between FSK demodulation, Tip/Ring CAS detection and Hybrid CAS detection.
When CB0 is high and CB1, CB2 are both low the MT88E45B is put into a power down state
consuming minimal power supply current. See Tables 1 and 2.
17
CB2
Control Bit 2 (CMOS Input). Together with CB1 this pin selects the MT88E45B’s functionality
between FSK demodulation, Tip/Ring CAS detection and Hybrid CAS detection.
When CB0 is high and CB1, CB2 are both low the MT88E45B is put into a power down state
consuming minimal power supply current. See Tables 1 and 2.
18
GS2
Hybrid Gain Select (Output). This is the output of the hybrid receive connection op-amp. The opamp should be used to connect the MT88E45B to the telephone hybrid or speech IC receive pair.
The hybrid receive signal can be amplified or attenuated at GS2 via selection of the feedback
resistor between GS2 and IN2-. When the CPE is off-hook CAS detection of the GS2 signal
should be enabled via the CB1 and CB2 pins. See Tables 1 and 2.
19
IN2-
Hybrid Op-amp Inverting (Input).
20
IN2+
Hybrid Op-amp Non-Inverting (Input).
4
Zarlink Semiconductor Inc.
MT88E45
CB0 CB1 CB2
FSK
Interface
Data Sheet
Function
0/1
1
1
Set by CB0 FSK Demodulation. Tip/Ring input (GS1) selected. DR/STD is DR.
0/1
1
0
Set by CB0 Hybrid CAS Detection. Hybrid Receive input (GS2) selected. DR/STD is STD.
0/1
0
1
Set by CB0 Tip/Ring CAS Detection. Tip/Ring input (GS1) selected. DR/STD is STD.
When the line is off-hook, a Bellcore/TIA Multiple Extension Interworking (MEI)
compatible Type 2 CPE should be able to detect CAS from Tip/Ring while the
CPE is on-hook because it may be the ACK sender. Tip/Ring CAS detection is
also required for BT’s on-hook CLIP.
1
0
0
Mode 1
Power Down. The MT88E45B is disabled and draws virtually no power supply
current.
0
0
0
Mode 0
Reserved for factory testing.
Table 1 - CB0/1/2 Functionality
The number of control bits (CB) required to interface the MT88E45B with the microcontroller depends on the
functionality of the application, as shown in Table 2.
Functionality Group
Controls
Description
FSK (mode 0 or 1) and
Hybrid CAS only
(Non MEI compatible)
CB2
CB0 is hardwired to Vdd or Vss to select the FSK
interface.
CB1 hardwired to Vdd.
The microcontroller uses CB2 to select between the 2
functions.
FSK (mode 0 or 1),
Hybrid CAS,
Tip/Ring CAS
(MEI compatible or BT on-hook CLIP)
CB1
CB2
CB0 is hardwired to Vdd or Vss to select the FSK
interface.
The microcontroller uses CB1 and CB2 to select between
the 3 functions.
FSK (mode 1),
Hybrid CAS,
Tip/Ring CAS,
Power Down
(MEI compatible or BT on-hook CLIP)
CB1
CB2
CB0 is hardwired to Vdd to select FSK interface mode 1.
The microcontroller uses CB1 and CB2 to select between
the 4 functions.
FSK (mode 0), Hybrid CAS,
Tip/Ring CAS, Power Down
(MEI compatible or BT on-hook CLIP)
CB0
CB1
CB2
All 3 pins are required.
Table 2 - Control Bit Functionality Groups
Functional Overview
The MT88E45B is compatible with FSK and FSK plus CAS (CPE Alerting Signal) based Caller ID services around
the world. Caller ID is the generic name for a group of services offered by telephone operating companies whereby
information about the calling party is delivered to the subscriber. In Europe and some other countries Caller ID is
known as Calling Line Identity Presentation (CLIP). ETSI calls CAS ‘Dual Tone Alerting Signal’ (DT-AS), BT calls it
‘Tone Alert Signal’.
Depending on the service, data delivery can occur when the line is in the on-hook or off-hook state. In most
countries the data is modulated in either Bell 202 or CCITT V.23 FSK format and transmitted at 1200 baud from the
serving end office to the subscriber’s terminal. Additionally in off-hook signalling, the special dual tone CAS is used
5
Zarlink Semiconductor Inc.
MT88E45
Data Sheet
to alert the terminal before FSK data transmission. BT uses CAS to alert the terminal prior to FSK in both on-hook
(Idle State) and off-hook (Loop State) signalling.
In North America, Caller ID uses the voiceband data transmission interface defined in the Bellcore document GR30-CORE. The terminal or CPE (Customer Premises Equipment) requirements are defined in Bellcore document
SR-TSV-002476. Typical services are CND (Calling Number Delivery), CNAM (Calling Name Delivery), VMWI
(Visual Message Waiting Indicator) and CIDCW (Calling Identity Delivery on Call Waiting).
In Europe, Caller ID requirements are defined by ETSI. The CPE documents are ETS 300 778-1 for on-hook, ETS
300 778-2 for off-hook. The end office requirements are ETS 300 659-1 (on-hook) and ETS 300 659-2 (off-hook).
ETSI has defined services such as CLIP and CLIP with Call Waiting which are similar to those of Bellcore. Some
European countries produce their own national specifications. For example, in the UK BT’s standards are SIN227
and SIN242, the UK CCA (Cable Communications Association) standard is TW/P&E/312.
In on-hook Caller ID, such as CND, CNAM and CLIP, the information is typically transmitted (in FSK) from the end
office before the subscriber picks up the phone. There are various methods such as between the first and second
rings (North America), between an abbreviated ring and the first true ring (Japan, France and Germany). On-hook
Caller ID can also occur without ringing for services such as VMWI. In BT’s on-hook CLIP, the signalling begins with
a line polarity reversal, followed by CAS and then FSK. Bellcore calls an on-hook capable Caller ID CPE a ‘Type 1
CPE’.
In off-hook Caller ID, such as CIDCW and CLIP with Call Waiting, information about a new calling party is sent to
the subscriber who is already engaged in a call. Bellcore’s method uses CAS to alert the CPE. When the CPE
detects CAS and there are no off-hook extensions, the CPE should mute its transmission path and send an
acknowledgment to the end office via a DTMF digit called ACK. Upon receiving ACK, the end office will send the
FSK data. Bellcore calls an off-hook capable CPE a ‘Type 2 CPE’. A Type 2 CPE is capable of off-hook and Type 1
functionalities and should ACK with a DTMF ‘D’. The ETSI and BT off-hook signalling protocols are similar to
Bellcore’s but with timing and signal parametric differences. ETSI has no requirement for off-hook extension
checking before ACK.
One factor affecting the quality of the CIDCW service is the CPE’s CAS speech immunity. Although the end office
has muted the far end party before and after it sends CAS, the near end (the end which is to receive the
information) user may be still talking. Therefore the CPE must be able to detect CAS successfully in the presence
of near end speech. This is called the talkdown immunity. The CPE must also be immune to imitation of CAS by
speech from both ends of the connection because the CAS detector is continuously exposed to speech throughout
the call. This is called the talkoff immunity.
If the CPE is a telephone, one way to achieve good CAS speech immunity is to put CAS detection on the telephone
hybrid or speech IC receive pair instead of on Tip and Ring. Talkdown immunity improves because the near end
speech has been attenuated while the CAS level is the same as on Tip/Ring, resulting in improved signal to speech
ratio. Talkoff immunity is also improved because the near end speech has been attenuated.
In the Bellcore SR-TSV-002476 Issue 1 off-hook protocol, the CPE should not ACK if it detected an off-hook
extension. The FSK will not be sent and the customer will not receive the Call Waiting ID. Bellcore, together with the
TIA (Telecommunications Industry Association) TR41.3.1 working group, has defined a CPE capability called
Multiple Extension Interworking (MEI) which overcomes this problem.
In the MEI scheme, all MEI compatible CPEs must be capable of detecting CAS when the line is off-hook, even
though the CPE itself may be on-hook. This is because under some conditions an on-hook CPE may become the
ACK sender. Another reason for the on-hook CPE to detect CAS is to maintain synchronous call logs between on
and off-hook CPEs. When CAS is received and all off-hook CPEs are MEI compatible, one of the CPEs will ACK
and all compatible CPEs will receive FSK.
A problem arises in a CPE where the CAS detector is connected only to the hybrid or speech IC receive pair: it
cannot detect CAS when it is on-hook. The reason is that when the CPE is on-hook either the hybrid/speech IC is
non functional or the signal level is severely attenuated. Therefore an on-hook Type 2 CPE must be capable of
6
Zarlink Semiconductor Inc.
MT88E45
Data Sheet
detecting CAS from Tip/Ring, in addition to detecting CAS from the hybrid/speech IC receive signal when it is offhook.
The MT88E45B offers an optimal solution which combines good speech immunity and MEI compatibility. Two input
op-amps allow the MT88E45B to be connected both to Tip/Ring and to the hybrid/speech IC receive pair. Both
connections can be differential or single ended. FSK demodulation is always on the Tip/Ring signal. CAS detection
can be from the Tip/Ring or hybrid/speech IC receive signal. Being able to detect CAS on Tip/Ring also makes the
MT88E45B suitable for BT on-hook CLIP applications.
For applications such as those in most European countries where Tip/Ring CAS detection is not needed, then the
Tip/Ring and Hybrid op-amp gains can be tailored independently to meet country specific FSK and CAS signal level
requirements respectively. Note that since the Hybrid op-amp is for CAS detection only, its gain can always be
tailored specifically for the CAS signal level.
The FSK demodulator is compatible with Bellcore, ETSI and BT standards. The demodulated FSK data is either
output directly (bit stream mode) or stored in a one byte buffer (buffer mode). In the buffer mode, the stop bit
immediately following a byte is also stored and can be shifted out after the data byte. This facility allows for framing
error checking required in Type 2 CPEs. In the bit stream mode, two timing signals are provided. One indicates the
bit sampling instants of the data byte, the other the end of byte. A carrier detector indicates presence of signal and
shuts off the data stream when there is no signal.
The entire chip can be put into a virtually zero current power down mode. The input op-amps, FSK demodulator,
CAS detector and the oscillator are all shut off. Furthermore, power management has been incorporated to
minimize operating current. When FSK is selected the CAS detector is powered down. When CAS is selected the
FSK demodulator is powered down.
Functional Description
3 to 5 V Operation
The MT88E45B’s FSK and CAS reject levels are proportional to Vdd. When operated at Vdd equal 3 V +/- 10%, to
keep the FSK and CAS reject levels as at 5 V (nominal) the Tip/Ring and Hybrid op-amp gains should be reduced
from those of 5 V. Gains for nominal Vdd (with a +/- 10% variation) other than 3 or 5 V can be chosen as
interpolation between the 3 and 5 V settings.
Input Configuration
The MT88E45B provides an input arrangement comprised of two op-amps and a bias source (VREF). VREF is a low
impedance voltage source which is used to bias the op-amp inputs at Vdd/2. The Tip/Ring op-amp (IN1+, IN1-, GS1
pins) is for connecting to Tip and Ring. The Hybrid op-amp (IN2+, IN2-, GS2 pins) is for connecting to the telephone
hybrid or speech IC receive pair.
Either FSK or CAS detection can be selected for the Tip/Ring connection, while the hybrid connection is for CAS
detection only. Phrased in another way, FSK demodulation is always on Tip/Ring, while CAS detection can be on
Tip/Ring or Hybrid Receive. Tip/Ring CAS detection is required for MEI and BT on-hook CLIP, while Hybrid CAS
detection is needed for optimal CAS speech immunity.
The feedback resistor connected between GS1 and IN1- can be used to adjust the Tip/Ring signal gain. The
feedback resistor connected between GS2 and IN2- can be used to adjust the hybrid receive signal gain. When the
Tip/Ring op-amp is selected, the GS2 signal is ignored. When the Hybrid op-amp is selected, the GS1 signal is
ignored.
Either or both op-amps can be configured in the single ended input configuration shown in Figure 33, or in the
differential input configuration shown in Figure 44.
7
Zarlink Semiconductor Inc.
MT88E45
Data Sheet
IN+
C
IN-
RIN
Voltage Gain
(AV) = RF / RIN
Highpass Corner Frequency
f-3dB = 1/(2πRINC)
GS
RF
VREF
Figure 3 - Single Ended Input Configuration
C1
R1
IN+
IN-
C2
R4
R5
GS
R2
R3
VREF
Differential Input Amplifier
C1 = C2
R1 = R4 (For unity gain R5= R4)
R3 = (R2R5) / (R2 + R5)
Voltage Gain
Highpass Corner Frequency
(AVdiff) = R5/R1
f-3dB = 1/(2πR1C1)
Input Impedance
(ZINdiff) = 2
R12 + (1/ωC)2
Figure 4 - Differential Input Configuration
CAS Detection
In North America, CAS is used in off-hook signalling only. In Europe (ETSI) it is used in off-hook signalling, and by
BT in both on and off-hook signalling. ETSI calls it the Dual Tone Alerting Signal (DT-AS). Although the ETSI onhook standard contains a DT-AS specification, BT is the only administration known to employ CAS in on-hook
signalling. (BT calls it Tone Alert Signal.) The CAS/DT-AS characteristics are summarized in Table 3.
BTc
(Off-hook = ‘Loop State’)
(On-hook = ‘Idle State’)
Bellcorea
(Off-hook only)
ETSIb
(Off-hook)
+/-0.5%
+/-0.5%
Off-hook: +/-0.6%
On-hook: +/-1.1%
Signal Level (per tone)
-14 to -32 dBmd
-9.78 to -32.78 dBm
(-12 to -35 dBVe)
+0.22 to -37.78 dBm
(-2 to -40 dBV)
Reject Level (per tone)
-45 dBm
Maximum Twist (V2130Hz/V2750Hz)
+/-6 dB
2130 Hz and 2750 Hz
CAS/DT-AS Characteristics
Frequency Tolerance
On-hook: -43.78 dBm
(-46 dBV)
+/-6 dB
8
Zarlink Semiconductor Inc.
+/-7 dB
MT88E45
2130 Hz and 2750 Hz
CAS/DT-AS Characteristics
Duration
Data Sheet
Bellcorea
(Off-hook only)
ETSIb
(Off-hook)
75 to 85 ms
75 to 85 ms
Reject Duration
Signal to Noise Ratio
BTc
(Off-hook = ‘Loop State’)
(On-hook = ‘Idle State’)
Off-hook: 80 to 85 ms
On-hook: 88 to 110 ms
Off-hook: <=70 ms
On-hook: <=20 ms
Speech
Speech
Off-hook: Speech
On-hook: >= 20 dB
(300-3400 Hz)
Hybrid Op-amp (GS2) Gain
Vdd = 5V +/- 10%
0 to -5 dB
0 to -5 dB
0 dB
Hybrid Op-amp (GS2) Gain
Vdd = 3V +/- 10%
-3.5 to -8.5 dB
-3.5 to -8.5 dB
-3.5 dB
a. SR-TSV-002476, Issue 1 Dec 1992
b. ETS 300 778-2 Jan 98. The DT-AS plus FSK variant of ETSI on-hook signalling described in ETS 300 778-1 is not supported
because on-hook DT-AS uses the GS1 op-amp. With the GS1 gain in Table 4, the DT-AS minimum level will be below the
MT88E45B’s minimum accept level.
c. SIN227 Issue 3 Nov 97, SIN242 Issue 2 Nov 96
d. dBm - Decibels above or below a reference power of 1 mW into 600 ohms. 0 dBm = 0.7746 Vrms.
e. dBV - Decibels above or below a reference voltage of 1 Vrms. 0 dBV = 1 Vrms
Table 3 - CAS/DT-AS Characteristics
Table 3 shows the Hybrid op-amp (GS2) gain for operation at 3 V and 5 V nominal Vdd, with a ± 10% Vdd variation.
For 3 V operation, the Hybrid op-amp gain should be reduced from the 5 V setting to maintain the CAS reject level
and to maintain the talkoff immunity: the CAS threshold is directly proportional to Vdd, when Vdd is reduced the
threshold becomes lower, hence lower level CAS are accepted. If the gain is not reduced, the MT88E45B will be
more talkoff prone. In Table 3, the GS2 gain is shown as a range. By adopting the lower gain, talkoff immunity can
be improved.
When CAS detection is selected, the dual purpose output pin DR/STD is STD. STD goes low when CAS has been
detected, and returns high after CAS has ended.
CAS Guard Time
The guard time circuit shown in Figure 55 implements a timing algorithm which determines whether the signal is a
CAS. Proper selection of the guard time(s) is key to good speech immunity. The first indication that there might be a
CAS is when EST goes high. EST high indicates that both tones are present. EST low indicates that one or both
tones is not present. STD low indicates that CAS has been detected. When STD returns high it indicates that CAS
has ended.
The timing algorithm consists of 2 components: a tone present guard time (tGP) and a tone absent guard time (tGA).
tGP sets the minimum accept duration for CAS. That is, both tones must be detected continuously for tGP for STD to
go low to indicate that CAS has been detected. For STD to return high to indicate that CAS has ended, one or both
tones must have disappeared for tGA. The purpose of tGA is to bridge over momentary EST dropouts once EST has
met the minimum tone duration so as to decrease the likelihood of a long talkoff being broken up into several
talkoffs. Usually tGA is set very short or removed altogether because there is another way to deal with the problem
(by ignoring further detections for 2 seconds after every detection).
9
Zarlink Semiconductor Inc.
MT88E45
Data Sheet
MT88E45B
Both Tones Present
Vdd
P Q1
C
+
ST/GT
-
VTGt
Vdiode
Comparator
R1
R2
N Q2
Rp=R1 || R2
= Vss
EST
DR/STD
Indicates STD in CAS
detection mode
CAS
tDP
tDA
tABS
EST
tREC
tGP
tGA
tGP=R1C ln [Vdd / (Vdd-VTGt)]
tGA=RpC ln
Vdd - Vdiode (Rp/R2)
VTGt - Vdiode (Rp/R2)
Rp=R1 || R2
ST/GT
tGA=0 if R2=0
STD
Figure 5 - CAS Guard Time Circuit Operation
Tone present guard time (tGP) operation: In Figure 5 5 initially there is no CAS, EST is low so Q1 is off. C has been
fully charged applying 0 V to ST/GT so Q2 is on. When both tones are detected EST goes high and turns off Q2.
Because C has been fully charged (ST/GT=0V), the comparator output is low and Q1 stays off. With both Q1 and
Q2 off the high at EST discharges C through R1 and the ST/GT voltage increases from 0 V. When the voltage
exceeds the comparator threshold VTGt, which is typically 0.5 Vdd, the comparator output goes high; Q1 turns on
and accelerates the discharge of C (ST/GT goes quickly to Vdd); STD goes low to indicate that a valid CAS has
been received. If one or both tones disappeared before tGP has been reached (i.e. when ST/GT voltage is still below
VTGt), Q2 turns back on and charges C quickly to bring the ST/GT voltage back to 0 V. Then if EST goes high again
the tGP duration must start over.
Tone absent guard time (tGA) operation: In Figure 5 5 initially both tones have been detected for tGP so C is fully
discharged and ST/GT is at Vdd. While both tones continue to be detected EST stays high; ST/GT is at Vdd (the
comparator output is high); so Q1 is on and Q2 is off. When one or both tones stop EST goes low and turns off Q1.
Because C is fully discharged (ST/GT=Vdd), the comparator output is high and Q2 stays off. With both Q1 and Q2
off the low at EST charges C through Rp=(R1 || R2) and the ST/GT voltage falls towards 0V. When the voltage has
fallen below VTGt, the comparator output goes low. Since EST is also low Q2 turns on and accelerates the
charging of C so that ST/GT goes quickly to 0V. STD goes high to indicate that the CAS has ended. If EST goes
back to high before tGA has been reached (i.e. when ST/GT voltage is still above VTGt), Q1 turns back on and
discharges C quickly to bring the ST/GT voltage back to Vdd. Then if EST goes low again the tGA duration must start
over. To set tGA=0, set R2 to 0.
10
Zarlink Semiconductor Inc.
MT88E45
Data Sheet
In Figure 55, tDP is the delay from the start of CAS to EST responding, tDA is the delay from the end of CAS to EST
responding. The total delay from the start of CAS to STD responding is tREC=tDP+tGP. The total delay from the end of
CAS to STD responding is tABS=tDA+tGA.
Parameter
North America: Bellcorea
Europe: ETSIb
UK: BTc
Mark (Logical 1) Frequency
1200 Hz +/- 1%
1300 Hz +/- 1.5%
Space (Logical 0) Frequency
2200 Hz +/- 1%
2100 Hz +/- 1.5%
-4.23 to -36.20 dBm
(476 to 12 mVrms)d
-5.78 to -33.78 dBme
(-8 to -36 dBV)f,g
Signal Reject Level
-48.24 dBm (3mVrms) for
On-hook No Ring Signalling
such as VMWI
On-hook only:
-47.78 dBm
(-50dBV)
Transmission Rate
1200 baud +/- 1%
1200 baud +/- 1%
Twist (VMARK/VSPACE)
-6 to +10 dB
-6 to +6 dB
Signal to Noise Ratio
Single Tone (f):
-18 dB (f<=60Hz)
-12 dB (60<f<=120Hz)
-6 dB (120<f<=200Hz)
+25 dB (200<f<3200Hz)
+6 dB (f>=3200Hz)
>= 25 dB
(300 to 3400 Hz)
>= 20 dB
(300 to 3400 Hz)
Tip/Ring Op-Amp (GS1) Gain
Vdd = 5V +/- 10%
0 dB
-2 dBh
0 dB
Tip/Ring Op-Amp (GS1) Gain
Vdd = 3V +/- 10%
-3.5 dB
-5.5 dBi
-3.5 dB
Received Signal Level
a.
b.
c.
d.
e.
f.
g.
h.
i.
-5.78 to -37.78 dBm
(-8 to -40 dBV)
ANSI/TIA/EIA-716 and TIA/EIA-777. Bellcore has agreed to the values and will synchronize its requirements.
ETS 300 778-1 (On-hook) Sep 97, ETS 300 778-2 (Off-hook) Jan 98.
SIN 227 Issue 3 Nov 97, SIN242 Issue 2 Nov 96.
North American on-hook signalling range. The off-hook range is inside the on-hook range: 190mVrms to 12mVrms.
dBm - Decibels above or below a reference power of 1 mW into 600 ohms. 0 dBm = 0.7746 Vrms
dBV - Decibels above or below a reference voltage of 1 Vrms. 0 dBV = 1 Vrms.
ETSI on-hook signalling range. The off-Hook signalling levels are inside this range: -8.78 to -30.78 dBm (-11 to -33 dBV).
The 5V ETSI Tip/Ring op-amp gain can be 0 dB if there is no FSK reject level requirement.
The 3V ETSI Tip/Ring op-amp gain can be -3.5dB if there is no FSK reject level requirement.
Table 4 - FSK Signal Characteristics
FSK Demodulation
The FSK characteristics are shown in Table 4. In North America, TIA (Telecommunications Industry Association)
also sets standards. The Type 1 Caller ID CPE standard is ANSI/TIA/EIA-716. The Type 2 standard is TIA/EIA-777.
The North American FSK characteristics in Table 4 are from ANSI/TIA/EIA-716. They differ from those Bellcore
published in SR-TSV-002476 and SR-3004. Bellcore is represented in TR41.3.1 and will synchronize to the TIA
requirements in its future documents.
The TIA Type 1 standard includes an FSK reject level:
•
if data is not preceded by ringing (e.g., VMWI), FSK signals below 3mVrms (-48.24 dBm) shall be rejected
•
if data is preceded by ringing, FSK detection may be extended below 3mVrms
The MT88E45B is compliant with the Bellcore/TIA, ETSI and BT requirements with the Tip/Ring op-amp gains in
Table 4. In Europe if the country specific FSK requirements do not incorporate ETSI’s FSK reject level then the
Tip/Ring op-amp gain can also be 0 dB at 5 V and -3.5 dB at 3 V to meet the ETSI minimum CAS level for on-hook
signalling (-40 dBV).
11
Zarlink Semiconductor Inc.
MT88E45
Data Sheet
For 3 V operation, the FSK receiver becomes more sensitive and lower level signals will be accepted than at 5 V. To
maintain the FSK reject level, the Tip/Ring input op-amp gain should be reduced. Note that since the Tip/Ring opamp is also used for Tip/Ring CAS detection, the CAS level will also be reduced for on-hook detection.
FSK Data Interface
The MT88E45B provides a powerful dual mode 3-wire interface so that the data bytes in the demodulated FSK bit
stream can be extracted without the need either for an external UART or for the CPE’s microcontroller to perform
the function in software. The interface is specifically designed for the 1200 baud rate and is consisted of 3 pins:
DATA, DCLK (Data Clock) and DR (Data Ready). DR/STD is a dual purpose output pin. When FSK is selected it is
DR.
Two modes (modes 0 and 1) are selectable via the CB0 pin. In mode 0, the FSK bit stream is output directly. In
mode 1, the data byte and the trailing stop bit are stored in a 9 bit buffer. If mode 1 is desired, the CB0 pin can be
hardwired to Vdd. If mode 0 is desired and full chip power down is not required, the CB0 pin can be hardwired to
Vss.
In Bellcore’s off-hook protocol, a Type 2 CPE should restore the voicepath within 50 ms after the end of the FSK
signal. Due to noise, end of carrier detection is not always reliable. The TIA Type 2 standard stipulates that the CPE
must detect the end of FSK when any one of the following occurs:
•
absence of carrier signal or,
•
more than five framing errors (trailing stop bit a 0 instead of a 1) have been detected in the FSK message or,
•
more than 150 ms of continuous mark signal or space signal has been detected.
Mode 0 - Bit Stream Mode
This mode is selected when the CB0 pin is low. In this mode the FSK data is output directly to the DATA pin. DCLK
and DR pins are timing signal outputs (see Figure 13.
For each received stop and start bit sequence, the MT88E45B outputs a fixed frequency clock string of 8 pulses at
the DCLK pin. Each DCLK rising edge occurs in the middle of a DATA bit cell. DCLK is not generated for the start
and stop bits. Consequently, DCLK will clock only valid data into a peripheral device such as a serial to parallel shift
register or a microcontroller. The MT88E45B also outputs an end of word pulse (Data Ready) at the DR pin. DR
goes low for half a nominal bit time at the beginning of the trailing stop bit. It can be used to interrupt a
microcontroller or cause a serial to parallel converter to parallel load its data into the microcontroller. Since the DR
rising edge occurs in the middle of the stop bit, it can also be used to read the stop bit to check for framing error.
Alternatively, DCLK and DATA may occupy 2 bits of a microcontroller’s input port. The microcontroller polls the
input port and saves the DATA bit whenever DCLK changes from low to high. When DR goes low, the word may
then be assembled from the last 8 saved bits.
DATA may also be connected to a personal computer’s serial communication port after conversion from CMOS to
RS-232 voltage levels.
Mode 1 - Buffer Mode
This mode is selected when the CB0 pin is high. In this mode the received byte is stored on chip. At the end of a
byte DR goes low to indicate that a new byte has become available. The microcontroller applies DCLK pulses to
read the register contents serially out of the DATA pin (see Figure 1414).
Internal to the MT88E45B, the start bit is stripped off, the data bits and the trailing stop bit are sampled and stored.
Midway through the stop bit, the 8 data bits and the stop bit are parallel loaded into a 9 bit shift register and DR
goes low. The register’s contents are shifted out to the DATA pin on the supplied DCLK’s rising edges in the order
they were received. The last bit must be shifted out and DCLK returned to low before the next DR. DCLK must be
low for tDDS before DR goes low and must remain low for tDDH after DR has gone low (see Figure 14).
12
Zarlink Semiconductor Inc.
MT88E45
Data Sheet
If DCLK begins while DR is low, DR will return to high upon the first DCLK rising edge. If DR interrupts a
microcontroller then this feature allows the interrupt to be cleared by the first read pulse. Otherwise DR is low for
half a nominal bit time (1/2400 sec).
Reading the stop bit allows the software to check for framing errors. When framing error is not checked
microcontroller only needs to send 8 DCLK pulses to shift the data byte out.
the
Carrier Detect
The carrier detector provides an indication of the presence of a signal in the FSK frequency band. It detects the
presence of a signal of sufficient amplitude at the output of the FSK bandpass filter. The signal is qualified by a
frequency aware digital algorithm before the CD output is set low to indicate carrier detection. A 10 ms hysteresis is
provided to allow for momentary signal dropout once CD has been activated. CD is released when there is no
activity at the FSK bandpass filter output for 10 ms.
When CD is inactive (high), the raw output of the FSK demodulator is ignored by the internal data timing recovery
circuit. In mode 0 the DATA, DCLK and DR pins are forced high. In mode 1 the output shift register is not updated
and DR is high; if DCLK is clocked, DATA is undefined.
Note that signals such as speech, CAS and DTMF tones also lie in the FSK frequency band and the carrier detector
may be activated by these signals. They will be demodulated and presented as data. To avoid the false data, the
MT88E45B should be put into CAS or power down mode when FSK is not expected. Ringing, on the other hand,
does not pose a problem as it is ignored by the carrier detector.
Interrupt
The DR/STD output can be used to interrupt a microcontroller. When the MT88E45B is the only interrupt source,
DR/STD can be connected directly to the microcontroller’s interrupt input. Figure 9 shows the necessary
connections when the MT88E45B is one of many interrupt sources. The diodes and resistors implement a wired-or
so that the microcontroller is interrupted (INT low active or falling edge triggered) when one or more of INT1, INT2
or DR/STD is low. The microcontroller can determine which one of DR/STD, INT1 or INT2 caused the interrupt by
reading them into an input port.
When system power is first applied and CB0/1/2 have already been configured to select CAS detection, DR/STD
will power up as logic low. This is because there is no charge across the ST/GT capacitor in Figure 55, hence
ST/GT is at Vdd which causes STD to be low. If DR/STD is used to interrupt a microcontroller the interrupt will not
clear until the capacitor has charged up. Therefore upon initial power up the microcontroller should ignore this
interrupt source until there is sufficient time to charge the capacitor. Alternatively, the MT88E45B can be put into
power down mode: DR/STD goes high and clears the interrupt, ST/GT goes low and the capacitor will charge up
quickly.
Power Down
The MT88E45B can be powered down to consume virtually no power supply current via a state of the CB0/1/2 pins.
Momentary transition of CB0/1/2 into the power down code will not activate power down.
In power down mode both input op-amps, VREF and the oscillator are non functional. DCLK becomes an input
because to select the power down state CB0 is 1 which will select FSK interface mode 1. If the application uses
FSK interface mode 0 and the MT88E45B needs to be powered down then a pull down resistor should be added
at the DCLK pin to define its state during power down (R15 in Figure 7). When the MT88E45B is powered down
DATA, DR/STD, CD are high; EST and ST/GT are low.
To reduce the operating current an Intelligent Power Down feature has been incorporated. When FSK is selected,
the CAS detector is powered down. When CAS is selected the FSK demodulator is powered down. The two input
op-amps are not affected and both will remain operational.
13
Zarlink Semiconductor Inc.
MT88E45
Data Sheet
Oscillator
The MT88E45B requires a 3.579545 MHz crystal or ceramic resonator to generate its oscillator clock. To meet the
CAS detection frequency tolerance specifications the crystal or resonator must have a 0.1% frequency tolerance.
The crystal specification is as follows: (e.g., CTS MP036S)
Frequency:
Frequency Tolerance:
Resonance Mode:
Load Capacitance:
Maximum Series
Resistance:
Maximum Drive Level:
3.579545 MHz
± 0.1% (over temperature
range of the application)
Parallel
18 pF
150 Ω
2 mW
Alternatively an external clock source can be used. In which case the OSC1 pin should be driven directly from a
CMOS buffer and the OSC2 pin left open.
For 5V+/-10% applications any number of MT88E45B’s can be connected as shown in Figure 6 6 so that only one
crystal is required.
MT88E45B
OSC1
OSC2
3.579545 MHz
MT88E45B
OSC1
OSC2
MT88E45B
OSC1
OSC2
to the
next MT88E45B
(For 5V+/-10% applications only)
Figure 6 - Common Crystal Connection
14
Zarlink Semiconductor Inc.
MT88E45
Data Sheet
Application Circuits
Tx+
TIP
TIP
RING
RING
Telephone
Hybrid
or
Speech IC
(Symbolic)
Microphone
Tx-
Rx+
Speaker
Rx-
R5
C1
R1
D1
R6
R3
D2
D3
C2 R2
R7
R4
D4
= To Microcontroller
Vss Xtal
= From Microcontroller
(FSK Interface Mode 1 selected)
R15 is required only if both FSK
interface mode 0 and power
down features are used.
R11
MT88E45B
R15
VREF
IN2+
IN1+
IN2-
IN1-
GS2
GS1
CB2
Vss
CB1
OSC1
Vdd
OSC2
CD
R10
R8 C3
R9 C4
R12
Vdd
C5
ST/GT
CB0
DCLK
EST
DATA
DR/STD
C6
R13
R14
D5
Unless stated otherwise, resistors are 1%, 0.1Watt; capacitors are 5%, 6.3V.
C6 should be
connected directly
across Vdd and Vss
pins
For 1000Vrms, 60Hz isolation from Tip to Earth and Ring to Earth:
R1,R2
430K, 0.5W, 5%, 475V min. C1,C2
2n2, 1332V min.
(e.g. IRC type GS-3)
If the 1000Vrms is handled by other methods then this circuit has to meet the FCC Part 68 Type B Ringer requirements:
R1,R2
432K, 0.1W, 1%, 56V min. C1,C2
2n2, 212V min.
Common to both sets of R1,R2:
R3,R4
34K
R8,R9
464K
R13
825K
R14
226K or 26K1
R15
100K, 20%
C3,C4
C5
C6
D1-D4
D5
Xtal
2n2
100n
100n, 20%
Diodes. 1N4148 or equivalent
Diode. 1N4148 or equivalent
3.579545MHz, 0.1% crystal
or ceramic resonator
R5,R10
R6,R11
R7,R12
5V, 0dB gain
53K6
60K4
464K
3V, -3.5dB gain
35K7
40K2
309K
Figure 7 - Application Circuit: Bellcore MEI Compatible Type 2 Telephone
15
Zarlink Semiconductor Inc.
MT88E45
Data Sheet
1.00
0.95
Gain ratio for
Bellcore GS1, GS2
ETSI GS2 op amps
0.90
0.85
0.794
Gain Ratio
0.80
0.75
0.70
0.65
Gain ratio for ETSI
GS1 op amp
0.668
0.60
0.55
0.531
0.50
3.0
3.5
4.0
4.5
5.0
Nominal Vdd (Volts)
Figure 8 - Gain Ratio as a Function of Nominal Vdd
Gain Setting Resistor Calculation Example for Figure 8:
•
For the desired nominal Vdd, use Figure 8 to determine approximate Av.
•
For the GS1 op-amp, start with the 0 dB gain setting resistor values of R5 0dB, R60dB and R70dB. In Figure 7
these values are 53K7, 60K4 and 464 K respectively. Keep C1,C2,R1,R2,R3,R4 as in Figure 7 to maintain
the highpass corner frequency constant for all gain settings.
•
For the desired gain setting of Av:
R7Av= R70dB x AV
Scaled for desired gain. Choose
the closest standard resistor value as R7Av.
Actual Av from now on is R7Av/R70db
R5Av= R50dB x AV
Scaled for good common mode range. Choose
the closest standard resistor value as R5Av.
1/R6Av = 1/R5Av - 1/R7Av
•
Calculate R6Av so that R5Av=R6Av || R7Av. Choose
the closest standard resistor value as R6Av.
Repeat for R10, R11, R12 for the GS2 op-amp.
16
Zarlink Semiconductor Inc.
MT88E45
Example:
•
•
•
Data Sheet
For a gain of -3.5 dB, Av =10-3.5/20 = 0.668
R7 -3.5dB= 464 K x 0.668 = 309K9, the closest standard resistor value is 309 K.
Av is now 309 K/464 K = 0.666
R5 -3.5dB= 53K6 x 0.666 = 35K7, the closest standard resistor value is 35K7.
Therefore R6-3.5dB is calculated to be 40K4, the closest standard resistor value is 40K2.
Vdd
Vdd
Interrupt Source 1
INT1
(Open Drain)
Interrupt Source 2
Resistor (R2)
Resistor (R1)
Microcontroller
D1
R1 can be opened and
D1 shorted if the
microcontroller does not
read the INT1 pin.
INT2
(CMOS)
INT(input)
MT88E45B
DR/STD
(CMOS)
Input Port Bit
Figure 9 - Application Circuit: Multiple Interrupt Source
17
Zarlink Semiconductor Inc.
MT88E45
Data Sheet
Absolute Maximum Ratings* - Voltages are with respect to VSS unless otherwise stated
Parameter
1
Symbol
Min.
Max.
Units
VDD
-0.3
6
V
VPIN
Vss-0.3
VDD+0.3
V
10
mA
150
oC
Supply voltage with respect to Vss
**
2
Voltage on any pin other than supplies
3
Current at any pin other than supplies
IPIN
4
Storage Temperature
TST
-65
* Exceeding these values may cause permanent damage. Functional operation under these conditions is not implied.
**
Under normal operating conditions voltage on any pin except supplies can be minimum VSS-1V to maximum VDD+1V for an input current
limited to less than 200 µΑ
Recommended Operating Conditions - Voltages are with respect to ground (VSS) unless otherwise stated.
Characteristics
Sym.
Min.
2.7
1
Power Supplies
VDD
2
Clock Frequency
fOSC
3
Tolerance on Clock Frequency
∆fOSC
Typ.‡
Max.
Units
5.5
V
3.579545
-0.1
-40
4 Operating Temperature
TOP
‡ Typical figures are at 25oC and are for design aid only: not guaranteed and not subject to production testing.
MHz
+0.1
%
85
oC
DC Electrical Characteristics†
Characteristics
Standby Supply
Current
1
2
S
U
P
P
L
Y
Sym.
IDDQ
Operating Supply
Current
VDD = 5V ±10%
VDD = 3V ±10%
IDD
3
Power
Consumption
PO
4
Schmitt Input High
Threshold
VT+
Schmitt Input Low
Threshold
DCLK
5
6
CB0
CB1
CB2
7
DCLK
DATA
DR/STD
CD, EST
ST/GT
Min.
Typ.‡
Max.
Units
Test Conditions
0.1
15
µA
All inputs are
VDD/VSS except
for oscillator pins.
No analog input.
outputs unloaded.
CB0/1/2 = 1/0/0
2.8
1.5
8
4.5
mA
mA
44
mW
0.44*VDD
0.64*VDD
V
VT-
0.27*VDD
0.47*VDD
V
Schmitt Hysteresis
VHYS
0.2
CMOS Input High
Voltage
VIH
0.7*VDD
VDD
V
CMOS Input Low
Voltage
VIL
VSS
0.3*VDD
V
Output High Source
Current
IOH
0.8
All inputs are
VDD/VSS except
for oscillator pins.
No analog input.
outputs unloaded.
V
mA
18
Zarlink Semiconductor Inc.
VOH=0.9*VDD
MT88E45
Data Sheet
DC Electrical Characteristics† (continued)
Characteristics
8
DCLK
DATA
DR/STD
CD, EST
ST/GT
9
IN1+
IN1IN2+
IN2-
Sym.
Min.
Output Low Sink
Current
IOL
2
Input Current
Iin1
ST/GT
11
VREF
12
13
ST/GT
Max.
Units
Test Conditions
mA
VOL=0.1*VDD
1
µA
Vin=VDD to VSS
Iin2
10
µA
Vin=VDD to VSS
Output HighImpedance Current
Ioz1
5
µA
Vout =VDD to VSS
Output Voltage
VREF
0.5VDD+0.1
V
Output Resistance
RREF
2
kΩ
Comparator
Threshold Voltage
VTGt
0.5VDD+0.05
V
DCLK
CB0
CB1
CB2
10
Typ.‡
0.5VDD -0.1
0.5VDD0.05
No Load
† DC Electrical Characteristics are over recommended operating conditions, unless otherwise stated.
‡ Typical figures are at 25oC and are for design aid only: not guaranteed and not subject to production testing.
AC Electrical Characteristics† - CAS Detection
Characteristic
Sym.
Min.
Typ.‡
Max.
Unit
Notes*
1
Lower Tone Frequency
fL
2130
Hz
2
Upper Tone Frequency
fH
2750
Hz
3
Frequency Deviation: Accept
1.1%
range within which
tones are
accepted
4
Frequency Deviation: Reject
3.5%
range outside of
which tones are
rejected
5
Accept Signal Level (per
tone)
-40
-37.78
6
-2
0.22
dBV
dBm
1, 5, 6
Reject Signal Level (per tone)
Vdd=5V +/-10% only
-46
-43.78
dBV
dBm
2, 5, 6
7
Reject Signal Level (per tone)
Vdd=3V+/-10% or 5V+/-10%
-47.22
-45
dBV
dBm
1, 5, 6
8
Twist: 20 log (V2130Hz/V2750Hz)
+7
dB
-7
20
dB
3,4
9
Signal to Noise Ratio
SNRCAS
† AC Electrical Characteristics are over recommended operating conditions, unless otherwise stated.
‡ Typical figures are at 25oC and are for design aid only: not guaranteed and not subject to production testing
*Notes:
1. Tip/Ring signal level. Input op-amp configured to 0dB gain at Vdd=5V+/-10%, -3.5dB at Vdd=3V+/-10%.
2. Tip/Ring signal level. Input op-amp configured to 0dB gain at Vdd=5V+/-10%.
3. Both tones have the same amplitude.
4. Band limited random noise 300-3400Hz. Measurement valid only when tone is present.
5. dBV - Decibels above or below a reference voltage of 1 Vrms. 0 dBV = 1 Vrms. Signal level is per tone.
6. dBm - Decibels above or below a reference power of 1 mW into 600 ohms. 0 dBm = 0.7746 Vrms. Signal level is per tone.
19
Zarlink Semiconductor Inc.
MT88E45
Data Sheet
AC Electrical Characteristics† - FSK Demodulation
Characteristics
Sym.
Min.
Typ.‡
-40
-37.78
10.0
Max.
Units
-6.45
-4.23
476
dBV
dBm
mVrms
1, 2, 4, 5
-48.24
-50.46
3
dBm
dBV
mVrms
1, 2, 4, 5
1
Accept Signal Level Range
2
Bell 202 Format Reject Signal Level
3
Transmission Rate
1188
1200
1212
baud
4
Mark and Space Frequencies
Bell 202 1 (Mark)
Bell 202 0 (Space)
1188
2178
1200
2200
1212
2222
Hz
Hz
1280.5
2068.5
1300
2100
1319.5
2131.5
Hz
Hz
+10
dB
CCITT V.23 1 (Mark)
CCITT V.23 0 (Space)
5
Twist: 20 log (VMARK/VSPACE)
-6
Notes*
20
dB
1,3
6 Signal to Noise Ratio
SNRFSK
† AC Electrical Characteristics are over recommended operating conditions, unless otherwise stated.
‡ Typical figures are nominal values and are for design aid only: not guaranteed and not subject to production testing.
*Notes:
1. Both mark and space have the same amplitude.
2. Tip/Ring signal level. Input op-amp configured to 0dB gain at Vdd=5V+/-10%, -3.5dB at Vdd=3V+/-10%.
3. Band limited random noise (200-3400Hz). Present when FSK signal is present. Note that the BT band is 300-3400Hz, the Bellcore
band is 0-4kHz.
4. dBV - Decibels above or below a reference voltage of 1 Vrms. 0 dBV = 1 Vrms.
5. dBm - Decibels above or below a reference power of 1 mW into 600 ohms. 0 dBm = 0.7746 Vrms.
Electrical Characteristics† - Gain Setting Amplifiers
Characteristics
Sym.
Min.
Max.
Units
1
µA
Test Conditions
VSS ≤ VIN ≤ VDD
1
Input Leakage Current
IIN
2
Input Resistance
Rin
3
Input Offset Voltage
VOS
4
Power Supply Rejection Ratio
PSRR
30
dB
1kHz ripple on VDD
5
Common Mode Rejection Ratio
CMRR
40
dB
VCMmin ≤ VIN ≤ VCMmax
6
DC Open Loop Voltage Gain
AVOL
40
dB
7
Unity Gain Bandwidth
fC
0.3
MHz
8
Output Voltage Swing
VO
0.5
9
Capacitive Load (GS1,GS2)
CL
10
Resistive Load (GS1,GS2)
RL
100
11
Common Mode Range Voltage
VCM
1.0
10
MΩ
25
VDD-0.5
V
50
pF
kΩ
VDD-1.0
† Electrical characteristics are over recommended operating conditions, unless otherwise stated.
20
Zarlink Semiconductor Inc.
mV
V
Load ≥ 100kΩ
MT88E45
Data Sheet
AC Electrical Characteristics† - CAS Detection Timing
Characteristics
Sym.
Min.
Max.
Units
tDP
0.5
10
ms
See Figures16 16, 1717
0.1
8
ms
2
Tone absent detect time
tDA
† AC Electrical Characteristics are over recommended operating conditions unless otherwise stated.
See Figures16 16, 1717
1
Tone present detect time
Notes
AC Electrical Characteristics† - Oscillator and Carrier Detect Timing
Characteristics
1
2
OSC2
3
4
CD
5
Sym.
Min.
Max.
Units
Power-up time
tPU
50
ms
Power-down time
tPD
10
ms
Input FSK to CD low delay
tCP
25
ms
Input FSK to CD high delay
tCA
Hysteresis
10
ms
10
ms
Notes
† AC Electrical Characteristics are over recommended operating conditions unless otherwise stated.
AC Electrical Characteristics† - 3-Wire FSK Data Interface Timing (Mode 0)
Characteristics
Sym.
Min.
Typ.‡
Max.
Units
Notes*
Rise time
tRR
200
ns
into 50 pF Load
Fall time
tRF
200
ns
into 50 pF Load
3
Low time
tRL
4
Rate
1
2
5
DR/STD
DATA
6
7
DATA
DCLK
Input FSK to DATA
delay
415
416
417
µs
2
1188
1200
1212
baud
1
1
5
ms
tIDD
Rise time
tR
200
ns
into 50 pF Load
Fall time
tF
200
ns
into 50 pF Load
DATA to DCLK delay
tDCD
6
416
µs
1, 2, 3
9
DCLK to DATA delay
tCDD
6
416
µs
1, 2, 3
10
Frequency
fDCLK0
1201.6
1202.8
1204
Hz
2
High time
tCH
415
416
417
µs
2
Low time
tCL
415
416
417
µs
2
tCRD
415
416
417
µs
2
8
11
DCLK
12
13
DCLK
DR/STD
DCLK to DR delay
† AC Electrical Characteristics are over recommended operating conditions unless otherwise stated.
‡ Typical figures are at 25oC and are for design aid only: not guaranteed and not subject to production testing.
*Notes:
1. FSK input data at 1200 ±12 baud.
2. OSC1 at 3.579545 MHz ±0.1%.
3. Function of signal condition.
21
Zarlink Semiconductor Inc.
MT88E45
Data Sheet
AC Electrical Characteristics† - 3-Wire FSK Data Interface Timing (Mode 1)
Characteristics
1
Sym.
Frequency
2
DCLK
3
4
DCLK
DR/STD
5
Min.
Max.
Units
1
MHz
70
%
100
ns
fDCLK1
Duty cycle
30
Rise time
tR1
DCLK low set up before DR
tDDS
500
ns
DCLK low hold time after DR
tDDH
500
ns
Notes
† AC Electrical Characteristics are over recommended operating conditions unless otherwise stated.
AC Electrical Characteristics - Timing Parameter Measurement Voltage Levels
Characteristics
Sym.
Level
Units
1
CMOS Threshold Voltage
VCT
0.5*VDD
V
2
Rise/Fall Threshold Voltage High
VHM
0.7*VDD
V
3
Rise/Fall Threshold Voltage Low
VLM
0.3*VDD
V
Notes
tCDD
tDCD
VHM
VCT
VLM
DATA
tF
tR
VHM
VCT
VLM
DCLK
tCL
tCH
tR
tF
Figure 10 - DATA and DCLK Mode 0 Output Timing
tRR
tRF
VHM
VCT
VLM
DR
tRL
Figure 11 - DR Output Timing
22
Zarlink Semiconductor Inc.
MT88E45
Data Sheet
VHM
DCLK
VLM
tR1
Figure 12 - DCLK Mode 1 Input Timing
start
TIP/RING
(A/B) WIRES
DATA
(Output)
b7
stop
b6 b7
start
b0 b1 b2 b3 b4 b5 b6 b7
start
b0 b1 b2 b3 b4 b5 b6 b7
stop
tIDD
start
b0 b1 b2 b3 b4 b5 b6 b7
stop
b0 b1 b2 b3 b4 b5
stop
start
start
b0 b1 b2 b3 b4 b5 b6 b7
stop
b0 b1 b2 b3
stop
DCLK
(Output)
tCH
tCL
tCRD
1/fDCLK0
DR
(Output)
tRL
Figure 13 - 3-Wire FSK Data Interface Timing (Mode 0)
23
Zarlink Semiconductor Inc.
MT88E45
Demodulated Data
(Internal Signal)
Data Sheet
Word N+1
Word N
stop
7
1
0
start
2
3
5
4
6
Note 1
DR (Data Ready)
(Output)
7
stop
tRL
Note 2
>tDDS
>tDDH
1/fDCLK1
DCLK (Data Clock)
(Schmitt Input)
DATA
(Output)
7
stop 0
1
Word N-1
2
3
4
5
6
7
0
stop
Word N
The DCLK input must be low before and after DR falling edge.
Note 1: DCLK occurs during DR low and returns DR to high.
Note 2: DCLK occurs after DR, so DR is low for half a nominal bit time.
Figure 14 - 3-Wire FSK Data Interface Timing (Mode 1)
TIP/RING
1st Ring
B
A
PWDN
Note 1
Ch. seizure
C
Data
Mark
D
2nd Ring
F
E
Note 2
Note 3
tPU
Note 2
Note 4
tPD
OSC2
FSKen
Note 1
tCA
tCP
CD
DR
Note 5
DCLK
DATA
..101010..
Data
A = 2sec typical
B = 250-500ms
C = 250ms
D = 150ms
E = feature specific
Max C+D+E = 2.9 to 3.7sec
F ≥ 200ms
Figure 15 - Application Timing for Bellcore On-hook Data Transmission Associated with Ringing,
e.g., CID
Notes:
This on-hook case application is included because a CIDCW (off-hook) CPE must be also capable of receiving on-hook data
transmission (with ringing) from the end office.
1) PWDN and FSKen are internal signals decoded from CB0/1/2.
2) The CPE designer may choose to enable the MT88E45B only after the end of ringing to conserve power in a battery operated CPE.
CD is not activated by ringing.
3) The microcontroller in the CPE powers down the MT88E45B after CD has become inactive.
4) The microcontroller times out if CD is not activated.
5) This signal represents the mode of the DR/STD pin.
24
Zarlink Semiconductor Inc.
MT88E45
CPE goes off-hook
Data Sheet
CPE unmutes handset
and enables keypad
CPE mutes handset & disables keypad
CPE sends
TIP/RING
CAS
A
Note 1
B
ACK
Note 5
C
D
Mark
E
Data
F
G
PWDN
Note 8
Hybrid CASen
Note 8
FSKen
Note 8
Note 3
Note 2
Note 4
tPU
OSC2
EST
ST/GT
tDP
tDA
tGA
VTGt
tGP
tREC
tABS
STD
Note 9
Note 6
tCP
Note 7
tCA
CD
DR
Note 9
DCLK
DATA
Data
A = 75-85 ms
B = 0-100 ms
C = 55-65 ms
D = 0-500 ms
E = 58-75 ms
F = feature specific
G ≤ 50 ms
Figure 16 - Application Timing for Bellcore Off-hook Data Transmission, e.g., CIDCW
Notes:
1) In a CPE where AC power is not available, the designer may choose to switch over to line power when the CPE goes off-hook and
use battery power while on-hook. The CPE must also be CID (on-hook) capable because a CIDCW CPE includes CID functionality.
2) Non-FSK signals such as CAS, speech and DTMF tones are in the same frequency band as FSK. They will be demodulated and
give false data. Therefore the MT88E45B should be taken out of FSK mode when FSK is not expected.
3) The MT88E45B may be put into FSK mode as soon as the CPE has finished sending the acknowledgment signal ACK. TR-NWT000575 specifies that ACK = DTMF ‘D’ for non-ADSI CPE, ‘A’ for ADSI CPE.
4) The MT88E45B should be taken out of FSK mode when CD has become inactive, or after 5 framing errors have been detected, or
after 150ms of continuous mark signal or space signal has been received. The framing errors need not be consecutive.
5) In an unsuccessful attempt where the end office does not send the FSK signal, the CPE should unmute the handset and enable the
keypad after interval D has expired.
6) The total recognition time is t REC = tGP + tDP , where tGP is the tone present guard time and tDP is the tone present detect time. V TGt
is the comparator threshold (refer to Figure 55 for details).
7) The total tone absent time is t ABS = tGA + t DA , where t GA is the tone absent guard time and t DA is the tone absent detect time. VTGt
is the comparator threshold (refer to Figure5 5 for details).
8) PWDN, Hybrid CASen and FSKen are internal signals decoded from CB0/1/2.
9) This signal represents the mode of the DR/STD pin.
25
Zarlink Semiconductor Inc.
MT88E45
Data Sheet
Line Reversal
A/B Wires
‘Idle State Tone Alert Signal’
Ch. seizure
DT-AS
A
B
C
Mark
D
E
Data
F
G
PWDN
Note 4
Note 6
Tip/Ring
CASen
Note 6
Ring
50-150ms
tDP
tDA
EST
Note 1
tGP
tGA
Note 2
VTGt
ST/GT
tREC
tABS
Note 3
STD
Note 7
TE DC load
15±1ms
< 0.5mA (optional)
<120µAµ
20±5ms
TE AC load
Current wetting pulse (see SIN227)
Note 4
Zss (Refer to SIN227)
FSKen
Note 5
Note 6
tCP
tCA
CD
DR
Note 7
DCLK
..101010..
DATA
Data
tPU
tPD
OSC2
A ≥ 100 ms
B = 88-110 ms
C ≥ 45 ms (up to 5sec)
D = 80-262 ms
E = 45-75 ms
F ≤ 2.5sec (typ. 500 ms)
G > 200 ms
Note:
All
values
obtained from SIN227
Issue 1
Figure 17 - Application Timing for BT Caller Display Service (CDS), e.g., CLIP
Notes:
1) The total recognition time is tREC = tGP + tDP , where tGP is the tone present guard time and tDP is the tone present detect time. V TGt
is the comparator threshold (refer to Figure 55 for details).
2) The total tone absent time is t ABS = tGA + t DA , where tGA is the tone absent guard time and t DA is the tone absent detect time. VTGt
is the comparator threshold (refer to Figure 55 for details).
3) By choosing t GA=15ms, t ABS will be 15-25ms so that the current wetting pulse and AC load can be applied right after the STD rising
edge.
4) SIN227 specifies that the AC and DC loads should be removed between 50-150ms after the end of the FSK signal, indicated by CD
returning to high. The MT88E45B may also be powered down at this time.
5) The MT88E45B should be taken out of FSK mode when FSK is not expected to prevent the FSK demodulator from reacting to other
in-band signals such as speech, DT-AS/CAS and DTMF tones.
6) PWDN, Tip/Ring CASen, FSKen are internal signals decoded from CB0/1/2.
7) This signal represents the mode of the DR/STD pin.
26
Zarlink Semiconductor Inc.
MT88E45
Data Sheet
Line Reversal (Optionally sent)
Ch. seizure
Ring Burst
A/B Wires
A
First Complete
Ring Cycle
B
Mark
C
D
Note 3
E
F
Note 2
50-150ms
Note 1
250-400ms
PWDN
Data
TE DC load
TE AC load
FSKen
Note 3
tCP
tCA
CD
DR
Note 4
DCLK
DATA
..101010..
Data
tPU
tPD
OSC2
A = 200-450 ms
B ≥ 500 ms
C = 80-262 ms
D = 45-262 ms
E ≤ 2.5s (typ. 500 ms)
F >200 ms
Note: Parameter F
from "CCA Exceptions
Document Issue 3"
Figure 18 - Application Timing for UK’s CCA Caller Display Service (CDS), e.g., CLIP
Notes:
1) From TW/P&E/312. Start time: The CPE should enter the signalling state by applying the DC and AC terminations within this time
after the end of the ring burst.
2) End time: The CPE should leave the signalling state by removing the DC and AC terminations within this time after the end of Data,
indicated by CD returning to high. The MT88E45B should also be taken out of FSK mode at this time to prevent the FSK
demodulator from reacting to other in-band signals such as speech, and DTMF tones.
3) PWDN and FSKen are internal signals decoded from CB0/1/2.
4) This signal represents the mode of the DR/STD pin.
27
Zarlink Semiconductor Inc.
For more information about all Zarlink products
visit our Web Site at
www.zarlink.com
Information relating to products and services furnished herein by Zarlink Semiconductor Inc. or its subsidiaries (collectively “Zarlink”) is believed to be reliable.
However, Zarlink assumes no liability for errors that may appear in this publication, or for liability otherwise arising from the application or use of any such
information, product or service or for any infringement of patents or other intellectual property rights owned by third parties which may result from such application or
use. Neither the supply of such information or purchase of product or service conveys any license, either express or implied, under patents or other intellectual
property rights owned by Zarlink or licensed from third parties by Zarlink, whatsoever. Purchasers of products are also hereby notified that the use of product in
certain ways or in combination with Zarlink, or non-Zarlink furnished goods or services may infringe patents or other intellectual property rights owned by Zarlink.
This publication is issued to provide information only and (unless agreed by Zarlink in writing) may not be used, applied or reproduced for any purpose nor form part
of any order or contract nor to be regarded as a representation relating to the products or services concerned. The products, their specifications, services and other
information appearing in this publication are subject to change by Zarlink without notice. No warranty or guarantee express or implied is made regarding the
capability, performance or suitability of any product or service. Information concerning possible methods of use is provided as a guide only and does not constitute
any guarantee that such methods of use will be satisfactory in a specific piece of equipment. It is the user’s responsibility to fully determine the performance and
suitability of any equipment using such information and to ensure that any publication or data used is up to date and has not been superseded. Manufacturing does
not necessarily include testing of all functions or parameters. These products are not suitable for use in any medical products whose failure to perform may result in
significant injury or death to the user. All products and materials are sold and services provided subject to Zarlink’s conditions of sale which are available on request.
Purchase of Zarlink’s I2C components conveys a licence under the Philips I2C Patent rights to use these components in and I2C System, provided that the system
conforms to the I2C Standard Specification as defined by Philips.
Zarlink, ZL and the Zarlink Semiconductor logo are trademarks of Zarlink Semiconductor Inc.
Copyright Zarlink Semiconductor Inc. All Rights Reserved.
TECHNICAL DOCUMENTATION - NOT FOR RESALE