Z86C47 ROM CPS DC-5462-00 P R E L I M I N A R Y PRELIMINARY CUSTOMER PRODUCT SPECIFICATION Z86C47 ROM CMOS Z8® 8-BIT MICROCONTROLLER GENERAL DESCRIPTION The Z86C47 Digital Television Controller (DTC) introduces a new level of sophistication to single-chip architecture. The Z86C47 is a member of the Z8 ® single-chip microcontroller family with 16 Kbytes of ROM and 236 bytes of RAM. The device is housed in a 64-pin DIP package, and is CMOS compatible. The part features ROMs for program storage and character generation. The Z86C47 microcontroller may be used in prototyping, low volume applications or where code development is required. Zilog’s DTC offers fast execution, efficient use of memory, sophisticated interrupts, input/output bit manipulation capabilities, and easy hardware/software system expansion along with low cost and low power consumption. The device provides an ideal performance and reliability solution for consumer and industrial television applications. The Z86C47 architecture utilizes Zilog’s advanced Superintegration™ design methodology. The device has an 8-bit internal data path controlled by a Z8 microcontroller, On-Screen Display (OSD) logic circuits/Pulse Width Modulators (PWM). On-chip peripherals include five register/ memory mapped I/O ports (Ports 2, 3, 4, 5, and 6), Interrupt control logic (1 software, 2 external and 3 internal interrupts) and a standby mode recovery input port (Port 3, pin P30). The OSD control circuits support eight rows by 20 columns for 128 kinds of characters. The character color is specified by row. One of the eight rows is assigned to show two kinds of colors for bar type displays such as volume control. The OSD is capable of displaying high resolution (11 x 15 dot pattern) characters. DTC applications demand powerful I/O capabilities. The Z86C47 fulfills this with 35 I/O pins dedicated to input and output. These lines are grouped into five ports, and are configurable under software control to provide timing, status signals, parallel I/O and an address/data bus for interfacing to external memory. There are three basic address spaces available to support this wide range of configurations: Program Memory, Register File and Data Memory. The Data Memory address space contains a number of control registers for the PWMs, OSD, and I/O Ports 4, 5, and 6. Specifically, there are 13 PWM and eight OSD control registers mapped into the external memory address space. Three I/O registers for Ports 4, 5, and 6 reside in data memory space as well. The Register File is composed of 236 bytes of general purpose register, two I/O Port registers and 15 control and status registers. To unburden the program from coping with the real-time problems such as counting/timing and data communication, the DTC’s offer two on-chip counter/timers with a large number of user selectable modes (see block diagram). Notes: All Signals with a preceding front slash, "/", are active Low, e.g., B//W (WORD is active Low); /B/W (BYTE is active Low, only). Power connections follow conventional descriptions below: Connection Circuit Device Power Ground VCC GND VDD VSS A 14-bit PWM port provides enough voltage resolution for a voltage synthesizer tuning system. Seven 6-bit PWM ports are used for controlling audio signal level. Five 8-bit PWM ports are used to vary picture levels. DC-5462-00 (7-14-93) 1 Z86C47 ROM CPS DC-5462-00 P R E L I M I N A R Y GENERAL DESCRIPTION (Continued) XTAL1 XTAL2 /RESET RESET Oscillator WDT Counter Timer Counter Timer P30 P31 P34 P35 P36 P40 P41 P42 P43 P44 P45 P46 P47 P50 P51 P52 P53 P54 P55 P56 P57 P60 P61 P62 P63 P64 P65 AFCIN 16K Byte Program ROM Port 2 Z8 CPU Core Port 3/ Interrupt PWM 1 14 -bit 256 Byte Register File PWM 2 to PWM 8 6-bit Port4 Port 0 Port 1 A8:15 AD0:7 PWM 9 to PWM 13 8-bit Port 5 160 Byte Character RAM Port 6 4 KByte Character ROM Functional Block Diagram 2 P27 P26 P25 P24 P23 P22 P21 P20 On-Screen Display PWM 1 PWM 2 PWM 3 PWM 4 PWM 5 PWM 6 PWM 7 PWM 8 PWM 9 PWM 10 PWM 11 PWM 12 PWM 13 OSCIN OSCOUT HSYNC VSYNC VRED VGREEN VBLUE VBLANK Z86C47 ROM CPS DC-5462-00 P R E L I M I N A R Y PIN CONFIGURATION PWM5 1 64 PWM6 PWM4 2 63 PWM7 PWM3 PWM2 3 4 62 PWM8 61 PWM9 PWM1 5 60 PWM10 P35 6 59 PWM11 P36 7 P34 P31 8 9 58 57 PWM12 PWM13 56 P27 P30 10 XTAL1 11 55 54 P26 P25 XTAL2 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 P24 P23 /RESET P60 GND P61 P62 VCC P63 P64 P65 AFCIN P50 P51 P52 P53 P54 P55 P56 P57 OSCIN OSCOUT Z86C47 33 GND P22 P21 VCC P20 P47 P46 P45 P44 P43 P42 P41 P40 VBLANK VBLUE VGREEN VRED VSYNC HSYNC Z86C47 Mask-ROM Plastic DIP 3 Z86C47 ROM CPS DC-5462-00 P R E L I M I N A R Y ABSOLUTE MAXIMUM RATINGS Stress greater than those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; operation of the device at any condition above those indicated in the operational sec- tions of these specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Symbol Parameters Min Max VCC VI VI VO IOH Power Supply Voltage † Input Voltage Input Voltage Output Voltage Output Current High –0.3 –0.3 –0.3 –0.3 IOH IOL IOL IOL TA TSTG Output Current High Output Current Low Output Current Low Output Current Low,all total Operating Temperature Storage Temperature †† –65 Notes: [1] Port 2 open-drain [2] PWM open-drain outputs [3] Port 5 Units Notes +7 VCC + 0.3 VCC + 0.3 VCC + 8.0 –10 V V V V mA [1] [2] 1 pin –100 20 40 200 mA mA mA mA +150 C all total 1 pin [3] (1 pin) † Voltage on all pins with respect to GND. †† See Ordering Information STANDARD TEST CONDITIONS VDD The characteristics listed below apply for standard test conditions as noted. All voltages are referenced to GND. Positive current flows into the referenced pin (see Test Load Diagram). RLL From Output Under Test 150 pF Test Load Diagram CAPACITANCE TA=25°C, VCC=GND=0 V, Freq=1.0 MHz, unmeasured pins to GND. Parameter Input capacitance Output capacitance I/O capacitance AFCIN input capacitance 4 Max Units 10 20 25 10 pF pF pF pF RLH Z86C47 ROM CPS DC-5462-00 P R E L I M I N A R Y DC CHARACTERISTICS TA=0°C to +70°C; VCC=+4.5 V to +5.5 V; FOSC=4 MHz TA=0°C to +70°C Min Max Symbol Parameter VIL VILC VIH VIHC Input Voltage Low Input XTAL/Osc In Low Input Voltage High Input XTAL/Osc in High VHY VPU VOL Schmitt Hysteresis Maximum Pull-up Voltage Output Voltage Low V00-01 V01-11 AFC Level 01 In AFC Level 11 In VOH IIR IIL IOL Output Voltage High Reset Input Current Input Leakage Tri-State Leakage ICC ICC1 ICC2 Supply Current 0 0.2 VCC 0.07 VCC VCC VCC 0.7 VCC 0.8 VCC 0.1 VCC 0.5 VCC 1.48 0.98 3.0 3.2 V V V V External Clock Generator Driven 0.8 [2] IOL=1.00 mA IOL=3.2 mA, [1] External Clock Generator Driven 12 0.4 0.4 0.16 0.19 V V V V 0.4 1.5 0.45 VCC 0.75 VCC 0.19 1.00 1.9 3.12 V V V V –80 3.0 3.0 4.75 –46 0.01 0.02 V µA µA µA IOH= –0.75 mA VRL=0 V 0 V,VCC 0 V,VCC 20 6 10 13.2 3.2 0.1 mA mA µA All inputs at rail All inputs at rail All inputs at rail VCC–0.4 –3.0 –3.0 Typical @ 25°C Units Conditions IOL=0.75 mA [2] IOL=10 mA [1] Notes: [1] Port 5 [2] PWM Open-Drain AC CHARACTERISTICS Timing Diagrams 1 3 7 XTAL1 5 Tin 3 2 2 External Clock 4 6 Counter Timer 5 Z86C47 ROM CPS DC-5462-00 P R E L I M I N A R Y AC CHARACTERISTICS Timing diagrams (Continued) IRQn 8 9 Interrupt Request Vcc 10 11 Internal /RESET 12 External /RESET Power On Reset HSYNC 13 OSC2 On Screen Display 6 14 Z86C47 ROM CPS DC-5462-00 P R E L I M I N A R Y AC CHARACTERISTICS TA=0° C to +70° C; VCC=+4.5 V to +5.5 V; FOSC=4 MHz, No Symbol Parameter Min Max 1 2 3 4 TpC TrC,TfC TwC TwTinL Input clock period Clock input raise and fall Input clock width Timer input low width 250 1000 15 ns ns ns ns 5 6 7 8A TwTinH TpTin TrTin,TfTin TwIL Timer input high width Timer input period Timer input raise and fall Int req input low 3 TpC 8 TpC 100 ns ns 8B 9 10 11 TwIL TwIH TdPOR TdLVIRES 100 ms ns 12 13 14 15 TwRES TdHsOI TdHsOh TdWDT Int request input high Power On Reset delay Low voltage detect to Internal RESET condition Reset minimum width Hsync start to Vosc stop Hsync end to Vosc start WDT Refresh Time 125 70 70 3 TpC 3 TpC 25 200 5 TpC 2 TpV 3 TpV 1 TpV 12 Unit ms Notes: [1] Refer to DC Characteristics for details on switching levels. * Units in nanoseconds 7 P R E L I M I N A R Y © 1993 by Zilog, Inc. All rights reserved. No part of this document may be copied or reproduced in any form or by any means without the prior written consent of Zilog, Inc. The information in this document is subject to change without notice. Devices sold by Zilog, Inc. are covered by warranty and patent indemnification provisions appearing in Zilog, Inc. Terms and Conditions of Sale only. Zilog, Inc. makes no warranty, express, statutory, implied or by description, regarding the information set forth herein or regarding the freedom of the described devices from intellectual property infringement. Zilog, Inc. makes no warranty of merchantability or fitness for any purpose. Zilog, Inc. shall not be responsible for any errors that may appear in this document. Zilog, Inc. makes no commitment to update or keep current the information contained in this document. 8 Z86C47 ROM CPS DC-5462-00 Zilog’s products are not authorized for use as critical components in life support devices or systems unless a specific written agreement pertaining to such intended use is executed between the customer and Zilog prior to use. Life support devices or systems are those which are intended for surgical implantation into the body, or which sustains life whose failure to perform, when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in significant injury to the user. Zilog, Inc. 210 East Hacienda Ave. Campbell, CA 95008-6600 Telephone (408) 370-8000 Telex 910-338-7621 FAX 408 370-8056