ILA2003 10W AUDIO AMPLIFIER DESCRIPTION The main features of ILA 2003, are very low number of external components, easy of assembly, space and cost saving. The device provides a high output current capability (up to 3.5A), very low harmonic and cross-over distortion. Completely safe operation is guaranteed due to protection against DC and AC short circuit between all pins and ground, thermal over-range, load dump voltage up to 40V and open ground. TO 220 AB/5 PENTAWATT ORDERING NUMBERS : ILA2003 ABSOLUTE MAXIMUM RATINGS Symbol Vs Vs Vs Io Io Ptot Tstg,Tj Parameter Peak supply voltage (50 ms) DC supply voltage Operating supply voltage Output peak current (repetitive) Output peak current (non repetitive) Power dissipation at Tcase =90°C Storage and junction temperature Value Unit 40 28 18 3.5 4.5 20 -40 to 150 V V V A A W °C Value Unit 3 °C/W PIN CONNECTION THERMAL DATA Symbol Rth-j-case Parameter Thermal resistance junction-case max 1 ILA2003 ELECTRICAL CHARACTERISTICS (Vs = 14.4V, Tamb =25 °C unless otherwise specified) Symbol Parameter Test conditions Min. Typ. DC CHARACTERISTICS Vs Supply voltage Vo Quiescent output voltage (pin 4) Id Quiescent drain current (pin 5) AC CHARACTERISTICS Po Output power Vi(rms) Input sensitivity B Frequency response ( -3 dB) d Distortion Ri Gv Input resistance (pin1) Voltage gain (open loop) Gv Voltage gain (closed loop) eN iN h Input noise voltage Input noise current Efficiency SVR Supply voltage rejection Unit 18 V 6.9 7.7 V 44 50 mA 8 6.1 d = 10% f = 1 kHz RL =4Ω RL =2Ω RL = 3.2Ω RL = 1.6Ω Input saturation voltage Vi Max. 5.5 9 6 10 7.5 12 W W W W 300 f = 1 kHz Po = 0.5W RL =4Ω Po =6W RL =4Ω Po = 0.5W RL =2Ω Po 10W RL =2Ω Po =1W RL =4Ω f = 1 kHz Po = 0.05 to4.5W RL =4Ω Po = 0.05 to7.5W RL =2Ω f = 1 kHz f = 1 kHz f = 10 kHz f = 1 kHz RL =4Ω f = 1 kHz Po =6W RL =4Ω Po 10W RL =2Ω f = 100 Hz Vripple = 0.5V Rg =10 kΩ RL =4 Ω (0) Filter with noise bandwidth: 22 Hz to 22 kHz 2 mV 14 55 10 50 40 to 15000 70 39,3 30 mV mV mV mV Hz 0,15 0,15 150 80 60 40 1 60 % % kΩ dB dB 40,3 5 200 dB µV pA 69 65 % % 36 dB ILA2003 IZ2003 CHIP DIAGRAM 2.6 + 0.03 2 .3 + 0.03 06 05 04 01 02 03 (0,0) Chip marking Chip marking (X=0,540, Y=0,530) YH14 PAD LOCATION Pin No Pad No Symbol X Y Pad size (mm) 01 01 IN 0.224 0.890 0.230 x 0.219 02 02 IN 0.113 0.291 0.230 x 0.209 03 03 GND 1.367 0.195 0.437 x 0.266 04 04 OUT 1.985 1.078 0.500 x 0.238 05 05 Ud 1.812 1.942 0.673 x 0.230 03 06 GND 0.132 1.957 0.258 x 0.230 Pad size is given as per metallization layer 3 ILA2003 4