Preliminary Datasheet High Sensitivity Micropower Omnipolar Hall-Effect Switch General Description Features The AH9249 is an ultra-sensitive Hall-effect switch with digital latched output, mainly designed for battery-operation, hand-held equipments. • • • Special CMOS process is used for low-voltage and low-power requirement. A chopper stabilized amplifier improves stability of magnetic switch points. A sleep-awake logic controls the IC in sleep time or awake time. This function will reduce the average operating current of the IC. During the awake time, the output is changed with the magnetic flux density. During the sleep time, the output is latched in its previous state and the current consumption will reduce to some µA. • • • • • AH9249 Micropower Operation 2.5 to 5.5V Power Supply Switching for Both Poles of a Magnet (Omnipolar) Stabilized Chopper Superior Temperature Stability Digital Output Signal Built-in Pull-up Resistor ESD Rating: 4000V (Human Body Model) 600V (Machine Model) Applications • • • The IC switching behaviour is omnipolar, either north or south pole sufficient strength will turn the output on. If the magnetic flux density is larger than operating point(BOP), the output will be turned on; if it is less than releasing point(BRP), the output will be turned off. Cover Switch in Notebook PC/PDA Handheld Wireless Application Awake Switch Magnet Switch in Low Duty Cycle Applications The AH9249 is available in TO-92S-3, SOT-23-3 and DFN-2×2-3 packages which are optimized for most applications. TO-92S-3 SOT-23-3 DFN-2×2-3 Figure 1. Package Types of AH9249 May. 2010 Rev. 1. 3 BCD Semiconductor Manufacturing Limited 1 Preliminary Datasheet High Sensitivity Micropower Omnipolar Hall-Effect Switch AH9249 Pin Configuration Z3 Package (TO-92S-3) N Package (SOT-23-3) 3 OUTPUT 2 GND 1 VCC GND 2 OUTPUT 1 VCC 3 (Front View) (Top View) DN Package (DFN-2×2-3) Pin 1 Dot by Marking VCC 1 3 OUTPUT GND 2 Figure 2. Pin Configuration of AH9249 Pin Description Pin Number Pin Name Function TO-92S-3 SOT-23-3 DFN-2×2-3 1 1 1 VCC Power supply pin 2 3 3 GND Ground pin 3 2 2 OUTPUT Output pin May. 2010 Rev. 1. 3 BCD Semiconductor Manufacturing Limited 2 Preliminary Datasheet High Sensitivity Micropower Omnipolar Hall-Effect Switch AH9249 Functional Block Diagram VCC 1 (1) Sleep/Awake Control Timing Logic Bias 3 (2) Hall Plate Chopper Comparator OUTPUT 2 (3) GND A (B) A for TO-92S-3 B for SOT-23-3 and DFN-2×2-3 Figure 3. Functional Block Diagram of AH9249 Ordering Information AH9249 Package Circuit Type G1: Green Package Z3: TO-92S-3 N: SOT-23-3 DN: DFN-2×2-3 Blank: Bulk TR: Tape and Reel Temperature Range TO-92S-3 SOT-23-3 DFN-2×2-3 - -40 to 85°C Part Number Marking ID Packing Type AH9249Z3-G1 9249 Bulk AH9249NTR-G1 GJ9 Tape & Reel AH9249DNTR-G1 JB Tape & Reel BCD Semiconductor's Pb-free products, as designated with "G1" suffix in the part number, are RoHS compliant and green. May. 2010 Rev. 1. 3 BCD Semiconductor Manufacturing Limited 3 Preliminary Datasheet High Sensitivity Micropower Omnipolar Hall-Effect Switch AH9249 Absolute Maximum Ratings (TA=25°C, Note 1) Parameter Symbol Value Unit Supply Voltage VCC 7 V Supply Current (Fault) ICC 6 mA Output Voltage VOUT 7 V Output Current IOUT 2 mA Magnetic Flux Density B Unlimited Gauss Power Dissipation PD TO-92S-3 SOT-23-3 DFN-2×2-3 400 230 230 Storage Temperature TSTG -55 to 150 Junction Temperature TJ 150 ESD (Human Body Model) (Note 2) 4000 ESD (Machine Model) (Note 2) 600 mW °C V Note 1: Stresses greater than those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “Recommended Operating Conditions” is not implied. Exposure to “Absolute Maximum Ratings” for extended periods may affect device reliability. Note 2: Electronic semiconductor products are sensitive to Electro Static Discharge (ESD). Always observe Electro Static Discharge control procedures whenever handling semiconductor products. Recommended Operating Conditions Parameter Symbol Min Max Unit Supply Voltage VCC 2.5 5.5 V Operating Temperature TOP -40 85 °C May. 2010 Rev. 1. 3 BCD Semiconductor Manufacturing Limited 4 Preliminary Datasheet High Sensitivity Micropower Omnipolar Hall-Effect Switch AH9249 Electrical Characteristics VCC =3V, TA =25°C, unless otherwise specified. Parameter Supply Voltage Supply Current Symbol Conditions Min Typ Max Unit 2.5 3 5.5 V VCC Operating IAW Awake 2 4 mA ISL Sleep 6 10 µA IAVG Average 10 15 µA 1.0 mA 1 µA 0.4 V Output Current IOUT Output Leakage Current ILEAK B<︱BRP︱ Saturation Voltage VSAT IOUT =1.0mA Awake Mode Time tAW Operating 150 Sleep Mode Time tSL Operating 90 Duty Cycle D 0.15 % Chopper Frequency fC 15 kHz <0.1 µs 120 ms Magnetic Characteristics (Note 3) VCC =3V, TA=25°C, unless otherwise specified. Parameter Symbol BOPS Operating Point BOPN BRPS Releasing Point BRPN Hysteresis BHYS Conditions South pole to branded side B>BOPS,VOUT=low (output on) North pole to branded side B>BOPN,VOUT=low (output on) South pole to branded side B<BRPS,VOUT=high (output off) North pole to branded side B<BRPN,VOUT=high (output off) ︱BOPX - BRPX︱(Note 4) Min Typ Max Unit 30 55 Gauss -55 -30 Gauss 5 20 Gauss -20 10 -5 Gauss Gauss Note 3: The specifications stated here are guaranteed by design. 1 Gauss=0.1Mt. Note 4: BOPX=operating point (output turns on); BRPX=releasing point (output turned off). May. 2010 Rev. 1. 3 BCD Semiconductor Manufacturing Limited 5 Preliminary Datasheet High Sensitivity Micropower Omnipolar Hall-Effect Switch AH9249 Output Voltage Magnetic Characteristics (Continued) Figure 4. Output Voltage vs. Magnetic Flux Density Test Conditions Figure 5. Average Supply Current (Note 5, 6) Note 5: ICC represents the average supply current. OUTPUT is open during measurement. Note 6: The device is put under magnetic field with B<BRP. May. 2010 Rev. 1. 3 BCD Semiconductor Manufacturing Limited 6 Preliminary Datasheet High Sensitivity Micropower Omnipolar Hall-Effect Switch AH9249 Test Conditions (Continued) Figure 6. Output Saturation Voltage (Note 7, 8) Note 7: The output saturation voltage VSAT is measured at VCC=2.5V and VCC=5.5V. Note 8: The device is put under magnetic field with B>BOP. Figure 7. Magnetic Thresholds (Note 9, 10) Note 9: BOP is determined by putting the device under magnetic field swept from BRP(min) to BOP(max) until the output is switched on. Note 10: BRP is determined by putting the device under magnetic field swept from BOP(max) to BRP(min) until the output is switched off. May. 2010 Rev. 1. 3 BCD Semiconductor Manufacturing Limited 7 Preliminary Datasheet High Sensitivity Micropower Omnipolar Hall-Effect Switch AH9249 Typical Performance Characteristics 50 50 40 TA=25 C 30 30 20 20 10 BOP1 0 BOP2 -10 BRP1 BOP/BRP (GS) BOP/BRP (GS) 40 o -20 -30 -30 -40 -40 3.00 3.25 BRP1 -10 BRP2 2.75 BOP2 0 -20 -50 2.50 BOP1 10 BRP2 -50 -40 3.50 -30 -20 -10 0 10 20 30 40 50 60 70 80 O TA ( C) VCC (V) Figure 8. BOP/BRP vs. Supply Voltage Figure 9. BOP/BRP vs. Ambient Temperature 300 15 14 o o 250 TA=25 C TA=25 C 13 200 tAW (µs) IAVG (µA) 12 11 10 150 100 9 8 50 7 6 2.50 2.75 3.00 3.25 0 2.50 3.50 3.00 3.25 3.50 VCC (V) VCC (V) Figure 10. Average Supply Current vs. Supply Voltage May. 2010 2.75 Figure 11. Awake Mode Time vs. Supply Voltage Rev. 1. 3 BCD Semiconductor Manufacturing Limited 8 Preliminary Datasheet High Sensitivity Micropower Omnipolar Hall-Effect Switch AH9249 Typical Performance Characteristics (Continued) 450 120 400 110 350 100 300 PD (mW) tSL (ms) TO-92S-3 SOT-23-3/DFN-2X2-3 o TA=25 C 90 80 250 200 150 70 100 60 50 2.50 50 0 2.75 3.00 3.25 0 3.50 25 50 75 100 125 150 O TA ( C) VCC (V) Figure 12. Sleep Mode Time vs. Supply Voltage May. 2010 Figure 13. Power Dissipation vs. Ambient Temperature Rev. 1. 3 BCD Semiconductor Manufacturing Limited 9 Preliminary Datasheet High Sensitivity Micropower Omnipolar Hall-Effect Switch AH9249 Typical Application Figure 14. Typical Application Circuit of AH9249 May. 2010 Rev. 1. 3 BCD Semiconductor Manufacturing Limited 10 Preliminary Datasheet High Sensitivity Micropower Omnipolar Hall-Effect Switch AH9249 Mechanical Dimensions TO-92S-3 ° ° Unit: mm(inch) 0.75(0.030) TYP 44 46 1.420(0.056) 1.620(0.064) 3.900(0.154) 4.100(0.161) 1.350(0.053) 1.650(0.065) 1.850(0.073) 2.150(0.085) 2.900(0.114) 3.100(0.122) Package Sensor Location 0.440(0.017) TYP 1.600(0.063) TYP 14.000(0.551) 15.000(0.590) 0.390(0.015) TYP 1.270(0.050) TYP May. 2010 0.380(0.015) TYP Rev. 1. 3 BCD Semiconductor Manufacturing Limited 11 Preliminary Datasheet High Sensitivity Micropower Omnipolar Hall-Effect Switch AH9249 Mechanical Dimensions (Continued) SOT-23-3 Unit: mm(inch) 2.820(0.111) 3.020(0.119) 0.100(0.004) 0.200(0.008) 0.300(0.012) 0.600(0.024) 2.650(0.104) 2.950(0.116) 1.500(0.059) 1.700(0.067) 1.45(0.057) TYP 0.200(0.008) 0.900(0.035) TYP 1.800(0.071) 2.000(0.079) 0 8 0.300(0.012) 0.500(0.020) 1.450(0.057) MAX. 0.950(0.037) TYP ° ° 0.000(0.000) 0.150(0.006) 0.900(0.035) 1.300(0.051) May. 2010 Rev. 1. 3 BCD Semiconductor Manufacturing Limited 12 Preliminary Datasheet High Sensitivity Micropower Omnipolar Hall-Effect Switch AH9249 Mechanical Dimensions (Continued) DFN-2×2-3 Unit: mm(inch) 1.220(0.048) 1.420(0.056) 1.900(0.075) 2.100(0.083) 0.300(0.012) 0.500(0.020) N3 Package Sensor Location (For Hall IC) 1.900(0.075) 2.100(0.083) 0.780(0.031) 0.980(0.039) Pin 1 Dot by Marking N2 0.850(0.033) 1.150(0.045) 0.990(0.039) 1.290(0.051) 0.650(0.026) TYP N1 0.200(0.008) MIN. 0.700(0.028) 0.800(0.031) 0.180(0.007) 0.300(0.012) May. 2010 0.000(0.000) 0.050(0.002) 0.203(0.008) REF Rev. 1. 3 BCD Semiconductor Manufacturing Limited 13 BCD Semiconductor Manufacturing Limited http://www.bcdsemi.com IMPORTANT NOTICE IMPORTANT NOTICE BCD Semiconductor BCD Semiconductor Manufacturing Manufacturing Limited Limited reserves reserves the the right right to to make make changes changes without without further further notice notice to to any any products products or or specifispecifications herein. cations herein. BCD BCD Semiconductor Semiconductor Manufacturing Manufacturing Limited Limited does does not not assume assume any any responsibility responsibility for for use use of of any any its its products products for for any any particular purpose, particular purpose, nor nor does does BCD BCD Semiconductor Semiconductor Manufacturing Manufacturing Limited Limited assume assume any any liability liability arising arising out out of of the the application application or or use use of any of any its its products products or or circuits. circuits. BCD BCD Semiconductor Semiconductor Manufacturing Manufacturing Limited Limited does does not not convey convey any any license license under under its its patent patent rights rights or or other rights other rights nor nor the the rights rights of of others. others. MAIN SITE SITE MAIN - Headquarters BCD Semiconductor Manufacturing Limited BCD Semiconductor Manufacturing Limited - Wafer Fab No. 1600, Zi Xing Road, Shanghai ZiZhu Science-basedLimited Industrial Park, 200241, China Shanghai SIM-BCD Semiconductor Manufacturing Tel: Fax: +86-21-24162277 800,+86-21-24162266, Yi Shan Road, Shanghai 200233, China Tel: +86-21-6485 1491, Fax: +86-21-5450 0008 REGIONAL SALES OFFICE Shenzhen OfficeSALES OFFICE REGIONAL - Wafer FabSemiconductor Manufacturing Limited BCD Shanghai SIM-BCD Semiconductor Manufacturing Co., Ltd. - IC Design Group 800 Yi Shan Road, Shanghai 200233, China Corporation Advanced Analog Circuits (Shanghai) Tel: +86-21-6485 1491,YiFax: 0008200233, China 8F, Zone B, 900, Shan+86-21-5450 Road, Shanghai Tel: +86-21-6495 9539, Fax: +86-21-6485 9673 Taiwan Office Shanghai Semiconductor Manufacturing Co., Ltd., Shenzhen Office BCD Taiwan Semiconductor Shenzhen SIM-BCD Office Office (Taiwan) Company Limited Unit A Room 1203, Skyworth Bldg., Gaoxin Ave.1.S., Nanshan Shenzhen, 4F, 298-1, Guang Road,(Taiwan) Nei-Hu District, Taipei, Shanghai SIM-BCD Semiconductor Manufacturing Co., Ltd.District, Shenzhen Office BCDRui Semiconductor Company Limited China Taiwan Advanced Analog Circuits (Shanghai) Corporation Shenzhen Office 4F, 298-1, Rui Guang Road, Nei-Hu District, Taipei, Tel: +86-755-8826 Tel: +886-2-2656 2808 Room E, 5F, Noble 7951 Center, No.1006, 3rd Fuzhong Road, Futian District, Shenzhen 518026, China Taiwan Fax: +86-755-88267951 7865 Fax: +886-2-2656 28062808 Tel: +86-755-8826 Tel: +886-2-2656 Fax: +86-755-8826 7865 Fax: +886-2-2656 2806 USA Office BCD Office Semiconductor Corp. USA 30920Semiconductor Huntwood Ave.Corporation Hayward, BCD CA 94544, USA Ave. Hayward, 30920 Huntwood Tel :94544, +1-510-324-2988 CA U.S.A Fax:: +1-510-324-2988 +1-510-324-2788 Tel Fax: +1-510-324-2788