BEL SFP-1GBT-01

10/100 BroadR-Reach™ RJ45 SFP Module
SFP-1GBT-01
FEATURES / BENEFITS
• Design based on Broadcom’s BroadR-Reach™ technology,
using their BCM54810S IC
(login at https://support.broadcom.com/Core/Login.aspx for
IC support)
• Complies with IEEE 802.3ab and Multi-Source Agreement
(MSA) specifications for SFP transceivers
• Supports IEEE 802.3u and IEEE 802.3ab auto–negotiation
features to allow networking equipment to automatically
determine and adjust the required settings
• Automatically compensates for baseline wander by removing
the DC offset from the input signal
• Low EMI emissions
• Automatic dependent interface (DI) crossover, eliminating
the need for crossover cables or cross-wire (MDIX) ports
• Bail latch provides ease of extraction
• Compact RJ45 connector assembly
Part Number
Description
SFP-1GBT-01
SGMII to 10/100Base-T SFP
BroadR-Reach™ Mode
• Data scrambled to reduce radiated emission
• Power consumption is 340mW typical
• Fully RoHS compliant
The BCM54810S physical layer IC (PHY) can be accessed via I 2 C interface:
PHY address = “ACh” for transceivers with serial number 0000000225 and higher.
PHY address = “82h” or “01” binary for transceivers with serial number 0000000224 and lower.
The EEPROM memory address = “A0h”
The Bel SFP-1GBT-01 module is internally configured for copper 10/100 BroadR-Reach™ mode. The host interface
transmits and receives serial data differentially at 1.25 Gbps.
• SFP Transceiver identification is specified as “04h” for byte 6 in the EEPROM.
REGULATORY AND STANDARDS COMPLIANCE
APPLICATIONS
•
Compliant with IEEE 802.3
•
•
FCC Part 15, Class A
10/100 Mbps data rate with an extended
reach of 300 to 500 meters when using
high quality Category 5/5e cable
•
EN55022 Class A (CISPR 22 Class A)
•
Networking equipment
•
Meets requirements of relevant European Directives (CE)
•
Switches-to-switches interface
•
E55024 Immunity standard and NEBS 3 ESD
•
Routers
©2011 Bel Fuse Inc. Specifications subject to change without notice. 04.29.11
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com
page 1
10/100 BroadR-Reach™ RJ45 SFP Module
SFP-1GBT-01
SFP-1BGT-01 MODULE SPECIFICATIONS
Parameter
Symbol
Min
Typ
Max
Units
Supply Voltage
V DD3
3.12
3.3
3.46
V
Supply Current
IS
100
Notes
mA
SFP Host
Serial Interface
(TX/RX)
Symbol
Line Frequency
F LINE
125
MHz
TX Output Impedance
Z TX_OUT
100
Ω
Differential
RX Output Impedance
Z RX_IN
100
Ω
Differential
25
MHz
4
ns
Min
Clock Frequency
Rise/Fall Time
T R /T F
RMS Phase Jitter
FJ
Typ
Max
1.5
Environmental
Specifications
Symbol
Min
Operating Temp
T OP
Storage Temp
T STG
Typ
Units
ps-rms
Notes
20% - 80%
F J = 12 kHz to 20 MHz
offset frequency
Max
Units
Notes
0
+70
°C
Case temperature
-40
+85
°C
Ambient temperature
©2011 Bel Fuse Inc. Specifications subject to change without notice. 04.29.11
page 2
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com
10/100 BroadR-Reach™ RJ45 SFP Module
SFP-1GBT-01
SFP HOST CONNECT ELECTRICAL INTERFACE AND PINS DESCRIPTIONS
Pin
Name
Description
1
VeeT
Transmitter ground (common with receiver ground).
2
TX Fault
Transmitter fault is internally tied to transmit ground and is not supported.
3
TX Disable
Transmit disable. This pin is tied to PHY low power mode.
4
MOD-DEF2
Signal SDA (data) of the two-wire serial ID interface.
5
MOD-DEF1
Signal SCL (data) of the two-wire serial ID interface.
6
MOD-DEF0
This pin is internally tied to transmit ground.
7
Rate Select
Not implemented. This pin is floating internally.
8
LOS
Loss of signal indication.
9
VeeR
Receiver ground (common with transmitter ground).
10
VeeR
Receiver ground (common with transmitter ground).
11
VeeR
Receiver ground (common with transmitter ground).
12
RD-
Differential receiver outputs. User to terminate to 100 Ω differential at
host. AC coupled.
13
RD+
Differential receiver outputs. User to terminate to 100 Ω differential at
host. AC coupled.
14
VeeR
Receiver ground (common with transmitter ground).
15
VccR
3.3V power
16
VccT
3.3V power
17
VeeT
Transmitter ground (common with receiver ground).
18
TD+
Differential transmitter outputs. User to terminate to 100 Ω differential at
host. AC coupled.
19
TD-
Differential transmitter outputs. User to terminate to 100 Ω differential
at host. AC coupled.
20
VeeT
Transmitter ground (common with receiver ground).
©2011 Bel Fuse Inc. Specifications subject to change without notice. 04.29.11
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com
page 3
10/100 BroadR-Reach™ RJ45 SFP Module
SFP-1GBT-01
MECHANICAL
©2011 Bel Fuse Inc. Specifications subject to change without notice. 04.29.11
CORPORATE
ASIA
EUROPE
Bel Fuse Inc.
206 Van Vorst Street
Jersey City, NJ 07302
Tel 201-432-0463
Fax 201-432-9542
www.belfuse.com
Bel Fuse Ltd.
8F / 8 Luk Hop Street
San Po Kong
Kowloon, Hong Kong
Tel 852-2328-5515
Fax 852-2352-3706
www.belfuse.com
Bel Stewart Connector
45/46 Riverside
Medway City Estate
Rochester, Kent ME2 4DP U.K.
Tel 44-1634-722890
Fax 44-1634-716677
www.belfuse.com
page 4