NON-ISOLATED DC/DC CONVERTERS 4.5 Vdc - 13.8 Vdc Input 0.59 Vdc - 5.1 Vdc / 10 A Output Bel Power Inc., a subsidiary of Bel Fuse Inc. Oct 07, 2010 VRAE-10E1A0 RoHS Compliant Rev.H • Non-Isolated • Under-Voltage Lockout • High Efficiency • Wide Trim • Fixed Frequency • OCP/SCP • Low Cost • Remote On/Off • Wide Input Description The Bel VRAE-10E1A0 is part of the non-isolated dc/dc converter Power Module series. The modules use a SIP package. These converters are available in a range of output voltages from 0.59 Vdc to 5.1 Vdc over a wide range of input voltage (VIN = 4.5 Vdc - 13.8 Vdc).The efficiency is typically 91% at 3.3 Vout (Vin=12 Vdc) at full load. Part Selection Output Voltage 0.59 V - 5.1 V Input Voltage 4.5 V - 13.8 V Max. Output Current 10 A Max. Output Power 50 W Typical Efficiency 91% Model Number VRAE-10E1A0 Notes: 1. All part numbers above indicate RoHS 6. Change the second letter "R" to "7" for RoHS 5 part numbers. 2. Add “G” suffix at the end of the model numbers listed above to indicate “Tray Packaging”. Absolute Maximum Ratings Parameter Input Supply Voltage Ambient Temperature Storage Temperature Min -0.3 V -40 °C Typ - Max 15 V 85 °C -55 °C - 125 °C Notes Note: All specifications are typical at 25 °C unless otherwise stated. Input Specifications Parameter Operating Input Voltage Vo,set≤3.63 V Vo,set﹥3.63 V Input Current (full load) Min Typ Max 4.5 V 7.0 V - 13.8 V 13.8 V - - 9.5 A Input Current (no load) - - 120 mA Remote Off Input Current - 10 mA 25 mA Input Reflected Ripple Current (pk-pk) - 30 mA 100 mA Input Reflected Ripple Current (rms) - 15 mA 30 mA I2t Inrush Current Transient - - 1 A2s Turn on Voltage Threshold 4.15 V 4.3 V 4.45 V Turn off Voltage Threshold 3.7 V 4.1 V 4.3 V Notes An input line fuse must always be used. With simulated source impedance of 1000 nH, 5 Hz to 20 MHz. Use a 1000 uF/25 V AL-Cap with ESR=0.03 ohm max and 2*100 uF/25V Tan-Cap with ESR=0.013 ohm max at 100 kHz@25°C. A 30.1K resistor is connected from Enable to Vin Note: All specifications are typical at 25 °C unless otherwise stated. Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com NON-ISOLATED DC/DC CONVERTERS 4.5 Vdc - 13.8 Vdc Input 0.59 Vdc - 5.1 Vdc / 10 A Output Bel Power Inc., a subsidiary of Bel Fuse Inc. Oct 07, 2010 Output Specifications Parameter Min Output Voltage Set Point Typ Max -2%Vo,set - 2%Vo,set Load Regulation - ±0.3%Vo,set ±1%Vo,set Line Regulation - ±0.3%Vo,set ±1%Vo,set Temperature Regulation - 0.3%Vo,set - 0A - 10 A 10.2 A 13 A 15 A Output Ripple and Noise (pk-pk) - 70 mV 100 mV Output Ripple and Noise (rms) - 20 mV 30 mV Short Circuit Surge Transient - - 5A s Turn on Time - - 7 mS Output Current Output DC Current Limit Overshoot at Turn on Output Capacitance Notes Vin= 12 V, lout=full load 0-20 MHz BW, with a 1 uF ceramic and a 10 uF tantalum capacitor at the output. 2 - - 1% 0 uF - 1000 uF - 120 mV 200 mV - 30 uS 50 uS - 120 mV 200 mV - 30 uS 50 uS Transient Response 50% ~ 100% Max Load Settling Time 100% ~ 50% Max Load VO =All Settling Time di/dt=0.25 A/uS; Vin= 12 V; with a 10 uF tantalum capacitor and a 1 uF ceramic capacitor at the output. Note: All specifications are typical at normal input, full load at Ta= 25°C unless otherwise stated. General Specifications Parameter Min Typ Max 91% 89% 87% 84% 83% 80% 73% 93% 91% 89% 86% 85% 82% 75% - - 500 kHz - 0.591 V - 5.1 V Notes Efficiency Vo=5.0 V Vo=3.3 V Vo=2.5 V Vo=1.8 V Vo=1.5 V Vo=1.2 V Vo=0.9 V Switching Frequency Output Voltage Trim Range (Wide Trim) MTBF Vin=12 V Calculated Per Bell Core SR-332 (IO = 80% load; Vin=12 V; Vo=5 V; 200 LFM; Ta = 25 °C) 7,677,401 hours Dimensions Inches (L × W × H) Millimeters (L × W × H) Weight 0.65 x 0.41 x 0.32 16.51 x 10.41 x 8.13 - 3.5 g - Note: All specifications are typical at 25 °C unless otherwise stated. Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com NON-ISOLATED DC/DC CONVERTERS 4.5 Vdc - 13.8 Vdc Input 0.59 Vdc - 5.1 Vdc / 10 A Output Bel Power Inc., a subsidiary of Bel Fuse Inc. Oct 07, 2010 Control Specifications Parameter Min Typ Max Notes Remote On/Off Signal Low (Unit Off) -0.3 V - 0.4 V Signal High (Unit On) 2.0 V - 5.5 V Remote On/Off Pin is open, the unit is off. Output Trim Equations Equation for calculating the trim resistor given the desired output voltage (Vo) is shown below. The Rtrim resistor should be connected between the trim pin and GND pin. Vout Rtrim = 1.182 kΩ Vo − 0.591 Module Trim Rtrimup GND Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com NON-ISOLATED DC/DC CONVERTERS 4.5 Vdc - 13.8 Vdc Input 0.59 Vdc - 5.1 Vdc / 10 A Output Bel Power Inc., a subsidiary of Bel Fuse Inc. Oct 07, 2010 Efficiency Data EFFICIENCY (%) Efficiency vs. Vo=0.591 V Output Current at Room Temperature 0.9 0.85 0.8 0.75 0.7 0.65 0.6 0.55 0.5 0.45 0.4 4.5V 12.0V 13.8V 1 2.5 5 7.5 10 OUTPUT CURRENT (Amp) EFFICIENCY (% Efficiency vs. Vo=3.3 V Output Current at Room Temperature 1 0.95 0.9 0.85 0.8 0.75 0.7 0.65 0.6 0.55 0.5 0.45 0.4 4.5V 12.0V 13.8V 1 2.5 5 7.5 10 OUTPUT CURRENT (Amp) EFFICIENCY (% Efficiency vs. Vo=5.0 V Output Current at Room Temperature 1 0.95 0.9 0.85 0.8 0.75 0.7 0.65 0.6 0.55 0.5 0.45 0.4 7V 12.0V 13.8V 1 2.5 5 7.5 10 OUTPUT CURRENT (Amp) Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com NON-ISOLATED DC/DC CONVERTERS 4.5 Vdc - 13.8 Vdc Input 0.59 Vdc - 5.1 Vdc / 10 A Output Bel Power Inc., a subsidiary of Bel Fuse Inc. Oct 07, 2010 Thermal Derating Curves The thermal reference point Tref is shown above. For reliable operation this temperature should not exceed 115°C. The output power of the module should not exceed the rated power for the module. Vin=12 V, Vout=5 V Vin=12 V, Vout=3.3 V Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com NON-ISOLATED DC/DC CONVERTERS 4.5 Vdc - 13.8 Vdc Input 0.59 Vdc - 5.1 Vdc / 10 A Output Bel Power Inc., a subsidiary of Bel Fuse Inc. Oct 07, 2010 Thermal Derating Curves (continued) Vin=12 V, Vout=2.5 V Vin=12 V, Vout=1.2 V Vin=12 V, Vout=0.59 V Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com NON-ISOLATED DC/DC CONVERTERS 4.5 Vdc - 13.8 Vdc Input Oct 07, 2010 0.59 Vdc - 5.1 Vdc / 10 A Output Bel Power Inc., a subsidiary of Bel Fuse Inc. Ripple and Noise Waveforms 12 V input, 0.591 V output 12 V input, 3.3 V output 12 V input, 5.0 V output Note: Ripple and noise at full load, 0-20MHz BW, with a 1 uF ceramic and a 10 uF tantalum capacitor at the output, Ta=25 deg C. Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com NON-ISOLATED DC/DC CONVERTERS 4.5 Vdc - 13.8 Vdc Input 0.59 Vdc - 5.1 Vdc / 10 A Output Oct 07, 2010 Bel Power Inc., a subsidiary of Bel Fuse Inc. Transient Response Waveforms 100% to 50% load step at 12 V input, 0.591 V output 50% to 100% load step at 12 V input, 0.591 V output 100% to 50% load step at 12 V input, 3.3 V output 50% to 100% load step at 12 V input, 3.3 V output 100% to 50% load step at 12 V input, 5.0 V output 50% to 100% load step at 12 V input, 5.0 V output Note: Transient response at di/dt=0.25 A/uS, with a 1uF ceramic cap and a 10 uF tantalum cap at the output, and Ta=25 deg C. Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com NON-ISOLATED DC/DC CONVERTERS 4.5 Vdc - 13.8 Vdc Input Oct 07, 2010 0.59 Vdc - 5.1 Vdc / 10 A Output Bel Power Inc., a subsidiary of Bel Fuse Inc. Mechanical Outline Pin Connections Pin Function 1 ENABLE 2 Vin 3 GND 4 Vout 5 Trim Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com NON-ISOLATED DC/DC CONVERTERS 4.5 Vdc - 13.8 Vdc Input 0.59 Vdc - 5.1 Vdc / 10 A Output Bel Power Inc., a subsidiary of Bel Fuse Inc. Oct 07, 2010 Revision History Date Revision 2010-04-22 G 2010-10-07 H Changes Detail Approval 1. Change operating temp range from 0~70°C to -40~85°C 2. Add the data of full load input current Update Thermal Derating Curves XF JIANG XF JIANG RoHS Compliance Complies with the European Directive 2002/95/EC, calling for the elimination of lead and other hazardous substances from electronic products. ©2010 Bel Fuse Inc. Specifications subject to change without notice. 100710 CORPORATE FAR EAST EUROPE Bel Fuse Inc. 206 Van Vorst Street Jersey City, NJ 07302 Tel 201-432-0463 Fax 201-432-9542 www.belfuse.com Bel Fuse Ltd. 8F/ 8 Luk Hop Street San Po Kong Kowloon, Hong Kong Tel 852-2328-5515 Fax 852-2352-3706 www.belfuse.com Bel Fuse Europe Ltd. Preston Technology Management Centre Marsh Lane, Suite G7, Preston Lancashire, PR1 8UD, U.K. Tel 44-1772-556601 Fax 44-1772-888366 www.belfuse.com