LM117, LM317A, LM317-N www.ti.com SNVS774O – MAY 2004 – REVISED JANUARY 2014 LM117/LM317A/LM317-N Three-Terminal Adjustable Regulator Check for Samples: LM117, LM317A, LM317-N FEATURES 1 • 2 • • • • • • • • Specified 1% Output Voltage Tolerance (LM317A) Specified max. 0.01%/V Line Regulation (LM317A) Specified max. 0.3% Load Regulation (LM117) Specified 1.5A Output Current Adjustable Output Down to 1.2V Current Limit Constant with Temperature P+ Product Enhancement tested 80 dB Ripple Rejection Output is Short-Circuit Protected DESCRIPTION The LM117 series of adjustable 3-terminal positive voltage regulators is capable of supplying in excess of 1.5A over a 1.2V to 37V output range. They are exceptionally easy to use and require only two external resistors to set the output voltage. Further, both line and load regulation are better than standard fixed regulators. Also, the LM117 is packaged in standard transistor packages which are easily mounted and handled. In addition to higher performance than fixed regulators, the LM117 series offers full overload protection available only in IC's. Included on the chip are current limit, thermal overload protection and safe area protection. All overload protection circuitry remains fully functional even if the adjustment terminal is disconnected. Normally, no capacitors are needed unless the device is situated more than 6 inches from the input filter capacitors in which case an input bypass is needed. An optional output capacitor can be added to improve transient response. The adjustment terminal can be bypassed to achieve very high ripple rejection ratios which are difficult to achieve with standard 3-terminal regulators. Besides replacing fixed regulators, the LM117 is useful in a wide variety of other applications. Since the regulator is “floating” and sees only the input-tooutput differential voltage, supplies of several hundred volts can be regulated as long as the maximum input to output differential is not exceeded, i.e., avoid short-circuiting the output. Also, it makes an especially simple adjustable switching regulator, a programmable output regulator, or by connecting a fixed resistor between the adjustment pin and output, the LM117 can be used as a precision current regulator. Supplies with electronic shutdown can be achieved by clamping the adjustment terminal to ground which programs the output to 1.2V where most loads draw little current. For applications requiring greater output current, see LM150 series (3A) and LM138 series (5A) data sheets. For the negative complement, see LM137 series data sheet. 1 2 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. All trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 2004–2014, Texas Instruments Incorporated LM117, LM317A, LM317-N SNVS774O – MAY 2004 – REVISED JANUARY 2014 www.ti.com Typical Applications Full output current not available at high input-output voltages *Needed if device is more than 6 inches from filter capacitors. †Optional—improves transient response. Output capacitors in the range of 1 μF to 1000 μF of aluminum or tantalum electrolytic are commonly used to provide improved output impedance and rejection of transients. Figure 1. 1.2V–25V Adjustable Regulator LM117/LM317A/LM317-N Package Options Part Number Package Drawing Package Type NDS TO-3 LM117K STEEL LM317K LM317AT LM317T NDE TO-220 LM317T/LF01 NDG LM317S KTT TO-263 DCY SOT-223 NDT TO LM317AEMP LM317EMP Output Current 1.5A 1.0A LM117H LM317AH LM317H LM317AMDT LM317MDT 0.5A NDP TO-252 NOTE For part numbers that can be ordered, please see the Package Option Addendum at the end of the datasheet. SOT-223 vs. TO-252 Packages Figure 2. Scale 1:1 2 Submit Documentation Feedback Copyright © 2004–2014, Texas Instruments Incorporated Product Folder Links: LM117 LM317A LM317-N LM117, LM317A, LM317-N www.ti.com SNVS774O – MAY 2004 – REVISED JANUARY 2014 Connection Diagrams CASE IS OUTPUT CASE IS OUTPUT Figure 3. TO-3 (NDS) Metal Can Package Bottom View Package Drawing NDS Figure 4. TO (NDT) Metal Can Package Bottom View Package Drawing NDT Figure 5. TO-263 (KTT) Surface-Mount Package Top View Package Drawing KTT Figure 6. TO-220 (NDE) Plastic Package Front View Package Drawing NDE Figure 7. 4-Lead SOT-223 (DCY) Top View Surface-Mount Package Package Number DCY Figure 8. TO-252 (NDP) Front View Surface Mount Package Package Drawing NDP These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. Copyright © 2004–2014, Texas Instruments Incorporated Product Folder Links: LM117 LM317A LM317-N Submit Documentation Feedback 3 LM117, LM317A, LM317-N SNVS774O – MAY 2004 – REVISED JANUARY 2014 www.ti.com ABSOLUTE MAXIMUM RATINGS (1) (2) Power Dissipation Internally Limited +40V, −0.3V Input-Output Voltage Differential −65°C to +150°C Storage Temperature Lead Temperature ESD Tolerance (1) (2) (3) Metal Package (Soldering, 10 seconds) 300°C Plastic Package (Soldering, 4 seconds) 260°C (3) 3 kV Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is intended to be functional, but do not ensure specific performance limits. For ensured specifications and test conditions, see the Electrical Characteristics. The ensured specifications apply only for the test conditions listed. If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/Distributors for availability and specifications. Human body model, 100 pF discharged through a 1.5 kΩ resistor. OPERATING TEMPERATURE RANGE LM117 −55°C ≤ TJ ≤ +150°C LM317A −40°C ≤ TJ ≤ +125°C 0°C ≤ TJ ≤ +125°C LM317-N Preconditioning Thermal Limit Burn-In 4 Submit Documentation Feedback All Devices 100% Copyright © 2004–2014, Texas Instruments Incorporated Product Folder Links: LM117 LM317A LM317-N LM117, LM317A, LM317-N www.ti.com SNVS774O – MAY 2004 – REVISED JANUARY 2014 LM117 ELECTRICAL CHARACTERISTICS (1) Specifications with standard type face are for TJ = 25°C, and those with boldface type apply over full Operating Temperature Range. Unless otherwise specified, VIN − VOUT = 5V, and IOUT = 10 mA. Parameter Conditions LM117 (2) Min Typ Max Units 1.20 1.25 1.30 V 0.01 0.02 0.02 0.05 %/V 0.1 0.3 0.3 1 % 0.03 0.07 %/W Adjustment Pin Current 50 100 μA 10 mA ≤ IOUT ≤ IMAX (1) Adjustment Pin Current Change 3V ≤ (VIN − VOUT) ≤ 40V 0.2 5 μA Reference Voltage 3V ≤ (VIN − VOUT) ≤ 40V, 10 mA ≤ IOUT ≤ IMAX (1) Line Regulation 3V ≤ (VIN − VOUT) ≤ 40V Load Regulation 10 mA ≤ IOUT ≤ IMAX (1) Thermal Regulation 20 ms Pulse Temperature Stability TMIN ≤ TJ ≤ TMAX Minimum Load Current (VIN − VOUT) = 40V (VIN − VOUT) ≤ 15V Current Limit (VIN − VOUT) = 40V RMS Output Noise, % of VOUT Ripple Rejection Ratio (3) (3) 1 3.5 5 NDS Package 1.5 2.2 3.4 NDT Package 0.5 0.8 1.8 NDS Package 0.3 0.4 NDT Package 0.15 0.20 10 Hz ≤ f ≤ 10 kHz VOUT = 10V, f = 120 Hz, CADJ = 0 μF VOUT = 10V, f = 120 Hz, CADJ = 10 μF 66 A % dB 80 0.3 Thermal Resistance, θJC Junction-to-Case NDS (TO-3) Package 2 NDT (TO) Package 21 Thermal Resistance, θJA Junction-to-Ambient (No Heat Sink) NDS (TO-3) Package 39 NDT (TO) Package 186 (3) A 65 TJ = 125°C, 1000 hrs (2) mA 0.003 Long-Term Stability (1) % dB 1 % °C/W °C/W IMAX = 1.5A for the NDS (TO-3), NDE (TO-220), and KTT (TO-263) packages. IMAX = 1.0A for the DCY (SOT-223) package. IMAX = 0.5A for the NDT (TO) and NDP (TO-252) packages. Device power dissipation (PD) is limited by ambient temperature (TA), device maximum junction temperature (TJ), and package thermal resistance (θJA). The maximum allowable power dissipation at any temperature is : PD(MAX) = ((TJ(MAX) - TA)/θJA). All Min. and Max. limits are ensured to TI's Average Outgoing Quality Level (AOQL). Specifications and availability for military and space grades of LM117/883 can be found in the LM117QML datasheet (SNVS356). Specifications and availability for military and space grades of LM117/JAN can be found in the LM117JAN datasheet (SNVS365). Regulation is measured at a constant junction temperature, using pulse testing with a low duty cycle. Changes in output voltage due to heating effects are covered under the specifications for thermal regulation. Copyright © 2004–2014, Texas Instruments Incorporated Product Folder Links: LM117 LM317A LM317-N Submit Documentation Feedback 5 LM117, LM317A, LM317-N SNVS774O – MAY 2004 – REVISED JANUARY 2014 www.ti.com LM317A and LM317-N ELECTRICAL CHARACTERISTICS (1) Specifications with standard type face are for TJ = 25°C, and those with boldface type apply over full Operating Temperature Range. Unless otherwise specified, VIN − VOUT = 5V, and IOUT = 10 mA. LM317A Parameter Conditions Reference Voltage 3V ≤ (VIN − VOUT) ≤ 40V, 10 mA ≤ IOUT ≤ IMAX (1) Line Regulation 3V ≤ (VIN − VOUT) ≤ 40V Load Regulation 10 mA ≤ IOUT ≤ IMAX (1) Thermal Regulation 20 ms Pulse Min Typ Max Min Typ Max Unit s 1.238 1.250 1.262 - 1.25 - V 1.225 1.250 1.270 1.20 1.25 1.30 V 0.005 0.01 0.01 0.02 0.01 0.02 0.04 0.07 %/V 0.1 0.3 0.5 1 0.1 0.3 0.5 1.5 % 0.04 0.07 0.04 0.07 %/W 50 100 50 100 μA 0.2 5 0.2 5 μA 10 3.5 10 mA (2) (2) Adjustment Pin Current Adjustment Pin Current Change 10 mA ≤ IOUT ≤ IMAX (1) 3V ≤ (VIN − VOUT) ≤ 40V Temperature Stability TMIN ≤ TJ ≤ TMAX Minimum Load Current (VIN − VOUT) = 40V 1 3.5 (VIN − VOUT) ≤ 15V Current Limit Ripple Rejection Ratio Long-Term Stability Thermal Resistance, θJC Junction-to-Case - - - 1.5 2.2 3.4 1.5 2.2 3.4 1.5 2.2 3.4 NDT Package 0.5 0.8 1.8 0.5 0.8 1.8 - - 0.15 0.40 DCY, NDE Packages 0.15 0.40 0.15 0.40 NDT Package 0.075 0.20 0.075 0.20 10 Hz ≤ f ≤ 10 kHz 0.003 VOUT = 10V, f = 120 Hz, CADJ = 0 μF VOUT = 10V, f = 120 Hz, CADJ = 10 μF TJ = 125°C, 1000 hrs 65 66 80 0.3 6 dB 80 0.3 - 2 4 KTT (TO-263) Package - 4 23.5 23.5 NDT (TO) Package 21 21 NDP (TO-252) Package 12 12 DCY (SOT-223) Package - 39 50 50 - 50 140 140 186 186 103 103 (3) DCY (SOT-223) Package NDP (TO-252) Package (3) 65 4 (3) NDT (TO) Package (2) 1 (3) A % NDE (TO-220) Package NDE (TO-220) Package (1) 66 A 0.003 NDS (TO-3) Package KTT (TO-263) Package % DCY, NDE Packages NDS (TO-3) Package Thermal Resistance, θJA Junction-to-Ambient (No Heat Sink) 1 NDS, KTT Packages NDS, KTT Packages (VIN − VOUT) = 40V RMS Output Noise, % of VOUT LM317-N dB 1 % °C/W °C/W IMAX = 1.5A for the NDS (TO-3), NDE (TO-220), and KTT (TO-263) packages. IMAX = 1.0A for the DCY (SOT-223) package. IMAX = 0.5A for the NDT (TO) and NDP (TO-252) packages. Device power dissipation (PD) is limited by ambient temperature (TA), device maximum junction temperature (TJ), and package thermal resistance (θJA). The maximum allowable power dissipation at any temperature is : PD(MAX) = ((TJ(MAX) - TA)/θJA). All Min. and Max. limits are ensured to TI's Average Outgoing Quality Level (AOQL). Regulation is measured at a constant junction temperature, using pulse testing with a low duty cycle. Changes in output voltage due to heating effects are covered under the specifications for thermal regulation. When surface mount packages are used (TO-263, SOT-223, TO-252), the junction to ambient thermal resistance can be reduced by increasing the PC board copper area that is thermally connected to the package. See the APPLICATION HINTS section for heatsink techniques. Submit Documentation Feedback Copyright © 2004–2014, Texas Instruments Incorporated Product Folder Links: LM117 LM317A LM317-N LM117, LM317A, LM317-N www.ti.com SNVS774O – MAY 2004 – REVISED JANUARY 2014 TYPICAL PERFORMANCE CHARACTERISTICS Output Capacitor = 0 μF unless otherwise noted Load Regulation Current Limit Figure 9. Figure 10. Adjustment Current Dropout Voltage Figure 11. Figure 12. VOUT vs VIN, VOUT = VREF VOUT vs VIN, VOUT = 5V Figure 13. Figure 14. Copyright © 2004–2014, Texas Instruments Incorporated Product Folder Links: LM117 LM317A LM317-N Submit Documentation Feedback 7 LM117, LM317A, LM317-N SNVS774O – MAY 2004 – REVISED JANUARY 2014 www.ti.com TYPICAL PERFORMANCE CHARACTERISTICS (continued) Output Capacitor = 0 μF unless otherwise noted 8 Temperature Stability Minimum Operating Current Figure 15. Figure 16. Ripple Rejection Ripple Rejection Figure 17. Figure 18. Ripple Rejection Output Impedance Figure 19. Figure 20. Submit Documentation Feedback Copyright © 2004–2014, Texas Instruments Incorporated Product Folder Links: LM117 LM317A LM317-N LM117, LM317A, LM317-N www.ti.com SNVS774O – MAY 2004 – REVISED JANUARY 2014 TYPICAL PERFORMANCE CHARACTERISTICS (continued) Output Capacitor = 0 μF unless otherwise noted Line Transient Response Load Transient Response Figure 21. Figure 22. Copyright © 2004–2014, Texas Instruments Incorporated Product Folder Links: LM117 LM317A LM317-N Submit Documentation Feedback 9 LM117, LM317A, LM317-N SNVS774O – MAY 2004 – REVISED JANUARY 2014 www.ti.com APPLICATION HINTS In operation, the LM117 develops a nominal 1.25V reference voltage, VREF, between the output and adjustment terminal. The reference voltage is impressed across program resistor R1 and, since the voltage is constant, a constant current I1 then flows through the output set resistor R2, giving an output voltage of (1) Since the 100 μA current from the adjustment terminal represents an error term, the LM117 was designed to minimize IADJ and make it very constant with line and load changes. To do this, all quiescent operating current is returned to the output establishing a minimum load current requirement. If there is insufficient load on the output, the output will rise. External Capacitors An input bypass capacitor is recommended. A 0.1 μF disc or 1μF solid tantalum on the input is suitable input bypassing for almost all applications. The device is more sensitive to the absence of input bypassing when adjustment or output capacitors are used but the above values will eliminate the possibility of problems. The adjustment terminal can be bypassed to ground on the LM117 to improve ripple rejection. This bypass capacitor prevents ripple from being amplified as the output voltage is increased. With a 10 μF bypass capacitor 80 dB ripple rejection is obtainable at any output level. Increases over 10 μF do not appreciably improve the ripple rejection at frequencies above 120 Hz. If the bypass capacitor is used, it is sometimes necessary to include protection diodes to prevent the capacitor from discharging through internal low current paths and damaging the device. In general, the best type of capacitors to use is solid tantalum. Solid tantalum capacitors have low impedance even at high frequencies. Depending upon capacitor construction, it takes about 25 μF in aluminum electrolytic to equal 1μF solid tantalum at high frequencies. Ceramic capacitors are also good at high frequencies; but some types have a large decrease in capacitance at frequencies around 0.5 MHz. For this reason, 0.01 μF disc may seem to work better than a 0.1 μF disc as a bypass. Although the LM117 is stable with no output capacitors, like any feedback circuit, certain values of external capacitance can cause excessive ringing. This occurs with values between 500 pF and 5000 pF. A 1 μF solid tantalum (or 25 μF aluminum electrolytic) on the output swamps this effect and insures stability. Any increase of the load capacitance larger than 10 μF will merely improve the loop stability and output impedance. Load Regulation The LM117 is capable of providing extremely good load regulation but a few precautions are needed to obtain maximum performance. The current set resistor connected between the adjustment terminal and the output terminal (usually 240Ω) should be tied directly to the output (case) of the regulator rather than near the load. This eliminates line drops from appearing effectively in series with the reference and degrading regulation. For example, a 15V regulator with 0.05Ω resistance between the regulator and load will have a load regulation due to line resistance of 0.05Ω × IL. If the set resistor is connected near the load the effective line resistance will be 0.05Ω (1 + R2/R1) or in this case, 11.5 times worse. Figure 23 shows the effect of resistance between the regulator and 240Ω set resistor. 10 Submit Documentation Feedback Copyright © 2004–2014, Texas Instruments Incorporated Product Folder Links: LM117 LM317A LM317-N LM117, LM317A, LM317-N www.ti.com SNVS774O – MAY 2004 – REVISED JANUARY 2014 Figure 23. Regulator with Line Resistance in Output Lead With the TO-3 package, it is easy to minimize the resistance from the case to the set resistor, by using two separate leads to the case. However, with the TO-39 package, care should be taken to minimize the wire length of the output lead. The ground of R2 can be returned near the ground of the load to provide remote ground sensing and improve load regulation. Protection Diodes When external capacitors are used with any IC regulator it is sometimes necessary to add protection diodes to prevent the capacitors from discharging through low current points into the regulator. Most 10 μF capacitors have low enough internal series resistance to deliver 20A spikes when shorted. Although the surge is short, there is enough energy to damage parts of the IC. When an output capacitor is connected to a regulator and the input is shorted, the output capacitor will discharge into the output of the regulator. The discharge current depends on the value of the capacitor, the output voltage of the regulator, and the rate of decrease of VIN. In the LM117, this discharge path is through a large junction that is able to sustain 15A surge with no problem. This is not true of other types of positive regulators. For output capacitors of 25 μF or less, there is no need to use diodes. The bypass capacitor on the adjustment terminal can discharge through a low current junction. Discharge occurs when either the input, or the output, is shorted. Internal to the LM117 is a 50Ω resistor which limits the peak discharge current. No protection is needed for output voltages of 25V or less and 10 μF capacitance. Figure 24 shows an LM117 with protection diodes included for use with outputs greater than 25V and high values of output capacitance. D1 protects against C1 D2 protects against C2 Figure 24. Regulator with Protection Diodes Copyright © 2004–2014, Texas Instruments Incorporated Product Folder Links: LM117 LM317A LM317-N Submit Documentation Feedback 11 LM117, LM317A, LM317-N SNVS774O – MAY 2004 – REVISED JANUARY 2014 www.ti.com Heatsink Requirements The LM317-N regulators have internal thermal shutdown to protect the device from over-heating. Under all operating conditions, the junction temperature of the LM317-N should not exceed the rated maximum junction temperature (TJ) of 150°C for the LM117, or 125°C for the LM317A and LM317-N. A heatsink may be required depending on the maximum device power dissipation and the maximum ambient temperature of the application. To determine if a heatsink is needed, the power dissipated by the regulator, PD, must be calculated: PD = ((VIN − VOUT) × IL) + (VIN × IG) (2) Figure 25 shows the voltage and currents which are present in the circuit. The next parameter which must be calculated is the maximum allowable temperature rise, TR(MAX): TR(MAX) = TJ(MAX) − TA(MAX) (3) where TJ(MAX) is the maximum allowable junction temperature (150°C for the LM117, or 125°C for the LM317A/LM317-N), and TA(MAX) is the maximum ambient temperature which will be encountered in the application. Using the calculated values for TR(MAX) and PD, the maximum allowable value for the junction-to-ambient thermal resistance (θJA) can be calculated: θJA = (TR(MAX) / PD) (4) Figure 25. Power Dissipation Diagram If the calculated maximum allowable thermal resistance is higher than the actual package rating, then no additional work is needed. If the calculated maximum allowable thermal resistance is lower than the actual package rating either the power dissipation (PD) needs to be reduced, the maximum ambient temperature TA(MAX) needs to be reduced, the thermal resistance (θJA) must be lowered by adding a heatsink, or some combination of these. If a heatsink is needed, the value can be calculated from the formula: θHA ≤ (θJA - (θCH + θJC)) (5) where (θCH is the thermal resistance of the contact area between the device case and the heatsink surface, and θJC is thermal resistance from the junction of the die to surface of the package case. When a value for θ(H−A) is found using the equation shown, a heatsink must be selected that has a value that is less than, or equal to, this number. The θ(H−A) rating is specified numerically by the heatsink manufacturer in the catalog, or shown in a curve that plots temperature rise vs power dissipation for the heatsink. Heatsinking Surface Mount Packages The TO-263 (KTT), SOT-223 (DCY) and TO-252 (NDP) packages use a copper plane on the PCB and the PCB itself as a heatsink. To optimize the heat sinking ability of the plane and PCB, solder the tab of the package to the plane. Heatsinking the SOT-223 (DCY) Package Figure 26 and Figure 27 show the information for the SOT-223 package. Figure 27 assumes a θ(J−A) of 74°C/W for 1 ounce copper and 51°C/W for 2 ounce copper and a maximum junction temperature of 125°C. Please see AN-1028 (literature number SNVA036) for thermal enhancement techniques to be used with SOT-223 and TO252 packages. 12 Submit Documentation Feedback Copyright © 2004–2014, Texas Instruments Incorporated Product Folder Links: LM117 LM317A LM317-N LM117, LM317A, LM317-N www.ti.com SNVS774O – MAY 2004 – REVISED JANUARY 2014 Figure 26. θ(J−A) vs Copper (2 ounce) Area for the SOT-223 Package Figure 27. Maximum Power Dissipation vs TAMB for the SOT-223 Package Heatsinking the TO-263 (KTT) Package Figure 28 shows for the TO-263 the measured values of θ(J−A) for different copper area sizes using a typical PCB with 1 ounce copper and no solder mask over the copper area used for heatsinking. As shown in Figure 28, increasing the copper area beyond 1 square inch produces very little improvement. It should also be observed that the minimum value of θ(J−A) for the TO-263 package mounted to a PCB is 32°C/W. Figure 28. θ(J−A) vs Copper (1 ounce) Area for the TO-263 Package Copyright © 2004–2014, Texas Instruments Incorporated Product Folder Links: LM117 LM317A LM317-N Submit Documentation Feedback 13 LM117, LM317A, LM317-N SNVS774O – MAY 2004 – REVISED JANUARY 2014 www.ti.com As a design aid, Figure 29 shows the maximum allowable power dissipation compared to ambient temperature for the TO-263 device (assuming θ(J−A) is 35°C/W and the maximum junction temperature is 125°C). Figure 29. Maximum Power Dissipation vs TAMB for the TO-263 Package Heatsinking the TO-252 (NDP) Package If the maximum allowable value for θJA is found to be ≥103°C/W (Typical Rated Value) for the TO-252 package, no heatsink is needed since the package alone will dissipate enough heat to satisfy these requirements. If the calculated value for θJA falls below these limits, a heatsink is required. As a design aid, Table 1 shows the value of the θJA of NDP the package for different heatsink area. The copper patterns that we used to measure these θJAs are shown in Figure 34. Figure 30 reflects the same test results as what are in Table 1. Figure 31 shows the maximum allowable power dissipation vs. ambient temperature for the TO-252 device. Figure 32 shows the maximum allowable power dissipation vs. copper area (in2) for the TO-252 device. Please see AN-1028 (literature number SNVA036) for thermal enhancement techniques to be used with SOT-223 and TO-252 packages. 14 Submit Documentation Feedback Copyright © 2004–2014, Texas Instruments Incorporated Product Folder Links: LM117 LM317A LM317-N LM117, LM317A, LM317-N www.ti.com SNVS774O – MAY 2004 – REVISED JANUARY 2014 Table 1. θJA Different Heatsink Area Layout (1) Copper Area Thermal Resistance Top Side (in2) (1) Bottom Side (in2) (θJA°C/W) TO-252 1 0.0123 0 103 2 0.066 0 87 3 0.3 0 60 4 0.53 0 54 5 0.76 0 52 6 1.0 0 47 7 0.066 0.2 84 8 0.066 0.4 70 9 0.066 0.6 63 10 0.066 0.8 57 11 0.066 1.0 57 12 0.066 0.066 89 13 0.175 0.175 72 14 0.284 0.284 61 15 0.392 0.392 55 16 0.5 0.5 53 Tab of device attached to topside of copper. Figure 30. θJA vs 2oz Copper Area for TO-252 Figure 31. Maximum Allowable Power Dissipation vs. Ambient Temperature for TO-252 Copyright © 2004–2014, Texas Instruments Incorporated Product Folder Links: LM117 LM317A LM317-N Submit Documentation Feedback 15 LM117, LM317A, LM317-N SNVS774O – MAY 2004 – REVISED JANUARY 2014 www.ti.com Figure 32. Maximum Allowable Power Dissipation vs. 2oz Copper Area for TO-252 Figure 33. Top View of the Thermal Test Pattern in Actual Scale 16 Submit Documentation Feedback Copyright © 2004–2014, Texas Instruments Incorporated Product Folder Links: LM117 LM317A LM317-N LM117, LM317A, LM317-N www.ti.com SNVS774O – MAY 2004 – REVISED JANUARY 2014 Figure 34. Bottom View of the Thermal Test Pattern in Actual Scale Schematic Diagram Copyright © 2004–2014, Texas Instruments Incorporated Product Folder Links: LM117 LM317A LM317-N Submit Documentation Feedback 17 LM117, LM317A, LM317-N SNVS774O – MAY 2004 – REVISED JANUARY 2014 www.ti.com Typical Applications NOTE: Min. output ≊ 1.2V Figure 35. 5V Logic Regulator with Electronic Shutdown Figure 36. Slow Turn-On 15V Regulator †Solid tantalum *Discharges C1 if output is shorted to ground Figure 37. Adjustable Regulator with Improved Ripple Rejection 18 Submit Documentation Feedback Copyright © 2004–2014, Texas Instruments Incorporated Product Folder Links: LM117 LM317A LM317-N LM117, LM317A, LM317-N www.ti.com SNVS774O – MAY 2004 – REVISED JANUARY 2014 Figure 38. High Stability 10V Regulator ‡Optional—improves ripple rejection †Solid tantalum *Minimum load current = 30 mA Figure 39. High Current Adjustable Regulator Copyright © 2004–2014, Texas Instruments Incorporated Product Folder Links: LM117 LM317A LM317-N Submit Documentation Feedback 19 LM117, LM317A, LM317-N SNVS774O – MAY 2004 – REVISED JANUARY 2014 www.ti.com Full output current not available at high input-output voltages Figure 40. 0 to 30V Regulator Figure 41. Power Follower 20 Submit Documentation Feedback Copyright © 2004–2014, Texas Instruments Incorporated Product Folder Links: LM117 LM317A LM317-N LM117, LM317A, LM317-N www.ti.com SNVS774O – MAY 2004 – REVISED JANUARY 2014 †Solid tantalum *Lights in constant current mode Figure 42. 5A Constant Voltage/Constant Current Regulator Figure 43. 1A Current Regulator *Minimum load current ≊ 4 mA Figure 44. 1.2V–20V Regulator with Minimum Program Current Copyright © 2004–2014, Texas Instruments Incorporated Product Folder Links: LM117 LM317A LM317-N Submit Documentation Feedback 21 LM117, LM317A, LM317-N SNVS774O – MAY 2004 – REVISED JANUARY 2014 www.ti.com Figure 45. High Gain Amplifier †Solid tantalum *Core—Arnold A-254168-2 60 turns Figure 46. Low Cost 3A Switching Regulator 22 Submit Documentation Feedback Copyright © 2004–2014, Texas Instruments Incorporated Product Folder Links: LM117 LM317A LM317-N LM117, LM317A, LM317-N www.ti.com SNVS774O – MAY 2004 – REVISED JANUARY 2014 †Solid tantalum *Core—Arnold A-254168-2 60 turns Figure 47. 4A Switching Regulator with Overload Protection Figure 48. Precision Current Limiter Figure 49. Tracking Preregulator Copyright © 2004–2014, Texas Instruments Incorporated Product Folder Links: LM117 LM317A LM317-N Submit Documentation Feedback 23 LM117, LM317A, LM317-N SNVS774O – MAY 2004 – REVISED JANUARY 2014 www.ti.com (Compared to LM117's higher current limit) —At 50 mA output only ¾ volt of drop occurs in R3 and R4 Figure 50. Current Limited Voltage Regulator *All outputs within ±100 mV †Minimum load—10 mA Figure 51. Adjusting Multiple On-Card Regulators with Single Control* Figure 52. AC Voltage Regulator 24 Submit Documentation Feedback Copyright © 2004–2014, Texas Instruments Incorporated Product Folder Links: LM117 LM317A LM317-N LM117, LM317A, LM317-N www.ti.com SNVS774O – MAY 2004 – REVISED JANUARY 2014 Use of RS allows low charging rates with fully charged battery. Figure 53. 12V Battery Charger Figure 54. 50mA Constant Current Battery Charger Figure 55. Adjustable 4A Regulator Copyright © 2004–2014, Texas Instruments Incorporated Product Folder Links: LM117 LM317A LM317-N Submit Documentation Feedback 25 LM117, LM317A, LM317-N SNVS774O – MAY 2004 – REVISED JANUARY 2014 www.ti.com *Sets peak current (0.6A for 1Ω) **The 1000μF is recommended to filter out input transients Figure 56. Current Limited 6V Charger *Sets maximum VOUT Figure 57. Digitally Selected Outputs 26 Submit Documentation Feedback Copyright © 2004–2014, Texas Instruments Incorporated Product Folder Links: LM117 LM317A LM317-N LM117, LM317A, LM317-N www.ti.com SNVS774O – MAY 2004 – REVISED JANUARY 2014 REVISION HISTORY Changes from Revision N (Auust 2013) to Revision O Page • Deleted MDT Package .......................................................................................................................................................... 6 • Changed 0.112 ..................................................................................................................................................................... 6 • Changed 0.30 ....................................................................................................................................................................... 6 • Changed 0.112 ..................................................................................................................................................................... 6 • Changed 0.30 ....................................................................................................................................................................... 6 • Deleted MDT Package .......................................................................................................................................................... 6 Copyright © 2004–2014, Texas Instruments Incorporated Product Folder Links: LM117 LM317A LM317-N Submit Documentation Feedback 27 PACKAGE OPTION ADDENDUM www.ti.com 9-Jan-2014 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (°C) Device Marking (4/5) LM117H ACTIVE TO NDT 3 500 Green (RoHS & no Sb/Br) AU Level-1-NA-UNLIM -55 to 125 LM117HP+ LM117H/NOPB ACTIVE TO NDT 3 500 Green (RoHS & no Sb/Br) AU Level-1-NA-UNLIM -55 to 125 LM117HP+ LM117K STEEL ACTIVE TO-3 NDS 2 50 TBD Call TI Call TI -55 to 125 LM117K STEELP+ LM117K STEEL/NOPB ACTIVE TO-3 NDS 2 50 Green (RoHS & no Sb/Br) POST-PLATE Level-1-NA-UNLIM -55 to 125 LM117K STEELP+ LM317AEMP NRND SOT-223 DCY 4 1000 TBD Call TI Call TI -40 to 125 N07A LM317AEMP/NOPB ACTIVE SOT-223 DCY 4 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 N07A LM317AEMPX NRND SOT-223 DCY 4 2000 TBD Call TI Call TI LM317AEMPX/NOPB ACTIVE SOT-223 DCY 4 2000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 N07A N07A LM317AH ACTIVE TO NDT 3 500 Green (RoHS & no Sb/Br) AU Level-1-NA-UNLIM -40 to 125 LM317AHP+ LM317AH/NOPB ACTIVE TO NDT 3 500 Green (RoHS & no Sb/Br) AU Level-1-NA-UNLIM -40 to 125 LM317AHP+ LM317AMDT NRND TO-252 NDP 3 75 TBD Call TI Call TI -40 to 125 LM317 AMDT LM317AMDT/NOPB ACTIVE TO-252 NDP 3 75 Green (RoHS & no Sb/Br) CU SN Level-2-260C-1 YEAR -40 to 125 LM317 AMDT LM317AMDTX NRND TO-252 NDP 3 2500 TBD Call TI Call TI -40 to 125 LM317 AMDT LM317AMDTX/NOPB ACTIVE TO-252 NDP 3 2500 Green (RoHS & no Sb/Br) CU SN Level-2-260C-1 YEAR -40 to 125 LM317 AMDT LM317AT NRND TO-220 NDE 3 45 TBD Call TI Call TI -40 to 125 LM317AT P+ LM317AT/NOPB ACTIVE TO-220 NDE 3 45 Pb-Free (RoHS Exempt) CU SN Level-1-NA-UNLIM -40 to 125 LM317AT P+ LM317EMP NRND SOT-223 DCY 4 1000 TBD Call TI Call TI 0 to 125 N01A LM317EMP/NOPB ACTIVE SOT-223 DCY 4 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM 0 to 125 N01A LM317EMPX/NOPB ACTIVE SOT-223 DCY 4 2000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM 0 to 125 N01A Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com 9-Jan-2014 Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (°C) Device Marking (4/5) LM317H ACTIVE TO NDT 3 500 Green (RoHS & no Sb/Br) AU Level-1-NA-UNLIM 0 to 125 LM317HP+ LM317H/NOPB ACTIVE TO NDT 3 500 Green (RoHS & no Sb/Br) AU Level-1-NA-UNLIM 0 to 125 LM317HP+ LM317K STEEL ACTIVE TO-3 NDS 2 50 TBD Call TI Call TI 0 to 125 LM317K STEELP+ LM317K STEEL/NOPB ACTIVE TO-3 NDS 2 50 Green (RoHS & no Sb/Br) POST-PLATE Level-1-NA-UNLIM 0 to 125 LM317K STEELP+ LM317MDT/NOPB ACTIVE TO-252 NDP 3 75 Green (RoHS & no Sb/Br) CU SN Level-2-260C-1 YEAR 0 to 125 LM317 MDT LM317MDTX/NOPB ACTIVE TO-252 NDP 3 2500 Green (RoHS & no Sb/Br) CU SN Level-2-260C-1 YEAR 0 to 125 LM317 MDT LM317S/NOPB ACTIVE DDPAK/ TO-263 KTT 3 45 Pb-Free (RoHS Exempt) CU SN Level-3-245C-168 HR 0 to 125 LM317S P+ LM317SX/NOPB ACTIVE DDPAK/ TO-263 KTT 3 500 Pb-Free (RoHS Exempt) CU SN Level-3-245C-168 HR 0 to 125 LM317S P+ LM317T NRND TO-220 NDE 3 45 TBD Call TI Call TI LM317T P+ LM317T/LF01 ACTIVE TO-220 NDG 3 45 Pb-Free (RoHS Exempt) CU SN Level-4-260C-72 HR LM317T P+ LM317T/NOPB ACTIVE TO-220 NDE 3 45 Green (RoHS & no Sb/Br) CU SN Level-1-NA-UNLIM 0 to 125 LM317T P+ (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) Addendum-Page 2 Samples PACKAGE OPTION ADDENDUM www.ti.com 9-Jan-2014 (3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. (6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish value exceeds the maximum column width. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 3 PACKAGE MATERIALS INFORMATION www.ti.com 9-Jan-2014 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant LM317AEMP SOT-223 DCY 4 1000 330.0 16.4 7.0 7.5 2.2 12.0 16.0 Q3 LM317AEMP/NOPB SOT-223 DCY 4 1000 330.0 LM317AEMPX SOT-223 DCY 4 2000 330.0 16.4 7.0 7.5 2.2 12.0 16.0 Q3 16.4 7.0 7.5 2.2 12.0 16.0 LM317AEMPX/NOPB SOT-223 DCY 4 2000 Q3 330.0 16.4 7.0 7.5 2.2 12.0 16.0 LM317AMDTX TO-252 NDP 3 Q3 2500 330.0 16.4 6.9 10.5 2.7 8.0 16.0 Q2 LM317AMDTX/NOPB TO-252 NDP LM317EMP SOT-223 DCY 3 2500 330.0 16.4 6.9 10.5 2.7 8.0 16.0 Q2 4 1000 330.0 16.4 7.0 7.5 2.2 12.0 16.0 LM317EMP/NOPB SOT-223 Q3 DCY 4 1000 330.0 16.4 7.0 7.5 2.2 12.0 16.0 Q3 LM317EMPX/NOPB LM317MDTX/NOPB SOT-223 DCY 4 2000 330.0 16.4 7.0 7.5 2.2 12.0 16.0 Q3 TO-252 NDP 3 2500 330.0 16.4 6.9 10.5 2.7 8.0 16.0 LM317SX/NOPB Q2 DDPAK/ TO-263 KTT 3 500 330.0 24.4 10.75 14.85 5.0 16.0 24.0 Q2 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 9-Jan-2014 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) LM317AEMP SOT-223 DCY 4 1000 367.0 367.0 35.0 LM317AEMP/NOPB SOT-223 DCY 4 1000 367.0 367.0 35.0 LM317AEMPX SOT-223 DCY 4 2000 367.0 367.0 35.0 LM317AEMPX/NOPB SOT-223 DCY 4 2000 367.0 367.0 35.0 LM317AMDTX TO-252 NDP 3 2500 367.0 367.0 35.0 LM317AMDTX/NOPB TO-252 NDP 3 2500 367.0 367.0 38.0 LM317EMP SOT-223 DCY 4 1000 367.0 367.0 35.0 LM317EMP/NOPB SOT-223 DCY 4 1000 367.0 367.0 35.0 LM317EMPX/NOPB SOT-223 DCY 4 2000 367.0 367.0 35.0 LM317MDTX/NOPB TO-252 NDP 3 2500 367.0 367.0 38.0 LM317SX/NOPB DDPAK/TO-263 KTT 3 500 367.0 367.0 45.0 Pack Materials-Page 2 MECHANICAL DATA NDT0003A H03A (Rev D) www.ti.com MECHANICAL DATA NDS0002A www.ti.com MECHANICAL DATA NDE0003B www.ti.com MECHANICAL DATA NDG0003F T03F (Rev B) www.ti.com MECHANICAL DATA NDP0003B TD03B (Rev F) www.ti.com MECHANICAL DATA MPDS094A – APRIL 2001 – REVISED JUNE 2002 DCY (R-PDSO-G4) PLASTIC SMALL-OUTLINE 6,70 (0.264) 6,30 (0.248) 3,10 (0.122) 2,90 (0.114) 4 0,10 (0.004) M 3,70 (0.146) 3,30 (0.130) 7,30 (0.287) 6,70 (0.264) Gauge Plane 1 2 0,84 (0.033) 0,66 (0.026) 2,30 (0.091) 4,60 (0.181) 1,80 (0.071) MAX 3 0°–10° 0,10 (0.004) M 0,25 (0.010) 0,75 (0.030) MIN 1,70 (0.067) 1,50 (0.059) 0,35 (0.014) 0,23 (0.009) Seating Plane 0,08 (0.003) 0,10 (0.0040) 0,02 (0.0008) 4202506/B 06/2002 NOTES: A. B. C. D. All linear dimensions are in millimeters (inches). This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion. Falls within JEDEC TO-261 Variation AA. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 MECHANICAL DATA KTT0003B TS3B (Rev F) BOTTOM SIDE OF PACKAGE www.ti.com IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2014, Texas Instruments Incorporated