EVERLIGHT 15-21-S2C-AL2M2VY-2T

EVERLIGHT ELECTRONICS CO.,LTD.
Technical Data Sheet
1206 Package Chip LED (1.1 mm Height)
15-21/S2C-AL2M2VY/2T
Features
․Package in 8mm tape on 7〞diameter reel.
․Compatible with automatic placement equipment.
․Compatible with infrared and vapor phase reflow
solder process.
․Mono-color type.
․Pb-free.
Descriptions
․The 15-21 SMD Taping is much smaller than lead frame
type components, thus enable smaller board
size, higher packing
density, reduced
storage space and finally smaller equipment
to be obtained.
․Besides, lightweight makes them ideal for
miniature applications. etc.
Applications
․Automotive: backlighting in dashboard and switch.
․Telecommunication: indicator and backlighting in
telephone and fax.
․Flat backlight for LCD, switch and symbol.
․General use.
Device Selection Guide
PART No.
15-21/S2C-AL2M2VY/2T
Chip
Material
Emitted Color
AlGaInP
Brilliant Orange
Lens Color
Water Clear
Everlight Electronics Co., Ltd.
http://www.everlight.com
Rev
1
Page: 1 of 10
Device No: SZDSE-151-S04
Prepared date: 25-Mar-2005
Prepared by: Zhang huali
EVERLIGHT ELECTRONICS CO.,LTD.
15-21/S2C-AL2M2VY/2T
Package Outline Dimensions
Note: The tolerances unless mentioned is ±0.1mm, Unit = mm
Everlight Electronics Co., Ltd.
http://www.everlight.com
Rev
1
Page: 2 of 10
Device No: SZDSE-151-S04
Prepared date: 25-Mar-2005
Prepared by: Zhang huali
EVERLIGHT ELECTRONICS CO.,LTD.
15-21/S2C-AL2M2VY/2T
Absolute Maximum Ratings (Ta=25℃)
Parameter
Symbol
Rating
Unit
Reverse Voltage
VR
5
V
Forward Current
IF
25
mA
Operating Temperature
Topr
-40 ~ +85
℃
Storage Temperature
Tstg
-40 ~ +90
℃
Electrostatic Discharge
ESD
2000
V
Power Dissipation
Pd
60
mW
IFP
60
mA
Peak Forward Current
(Duty 1/10 @1KHz)
Reflow Soldering : 260 ℃ for 10 sec.
Soldering Temperature
Tsol
Hand Soldering : 350 ℃ for 3 sec.
Electro-Optical Characteristics (Ta=25℃)
Parameter
Symbol
Min.
Typ.
Max.
Unit
Luminous Intensity
IV
14.5
-----
28.5
mcd
Viewing Angle
2θ1/2
-----
140
-----
deg
Peak Wavelength
λp
-----
611
-----
nm
Condition
IF=5mA
Dominant Wavelength
λd
600.5
----
612.5
nm
Spectrum Radiation
Bandwidth
△λ
-----
17
-----
nm
Forward Voltage
VF
1.70
-----
2.20
V
XC Reverse Current
IR
-----
-----
10
μA
VR=5V
Notes:
1.Tolerance of Luminous Intensity ±10%
2.Tolerance of Dominant Wavelength ±1nm
3.Tolerance of Forward Voltage ±0.05V
Everlight Electronics Co., Ltd.
http://www.everlight.com
Rev
1
Page: 3 of 10
Device No: SZDSE-151-S04
Prepared date: 25-Mar-2005
Prepared by: Zhang huali
EVERLIGHT ELECTRONICS CO.,LTD.
15-21/S2C-AL2M2VY/2T
Bin Range Of Dom. Wavelength
Group
A
Bin
Min
Max
D8
600.5
603.5
D9
603.5
606.5
D10
606.5
609.5
D11
609.5
612.5
Unit
Condition
nm
IF =5mA
Unit
Condition
mcd
IF =5mA
Unit
Condition
Bin Range Of Luminous Intensity
Bin
Min
Max
L2
14.5
18.0
M1
18.0
22.5
M2
22.5
28.5
Bin Range Of Luminous Voltage
Group
V
Bin
Min
Max
19
1.70
1.80
20
1.80
1.90
21
1.90
2.00
22
2.00
2.10
23
2.10
2.20
V
IF =5mA
Notes:
1.Tolerance of Luminous Intensity ±10%
2.Tolerance of Dominant Wavelength ±1nm
3.Tolerance of Forward Voltage ±0.05V
Everlight Electronics Co., Ltd.
http://www.everlight.com
Rev
1
Page: 4 of 10
Device No: SZDSE-151-S04
Prepared date: 25-Mar-2005
Prepared by: Zhang huali
EVERLIGHT ELECTRONICS CO.,LTD.
15-21/S2C-AL2M2VY/2T
Electro-Optical Characteristics (Ta=25℃)
Everlight Electronics Co., Ltd.
http://www.everlight.com
Rev
1
Page: 5 of 10
Device No: SZDSE-151-S04
Prepared date: 25-Mar-2005
Prepared by: Zhang huali
EVERLIGHT ELECTRONICS CO.,LTD.
15-21/S2C-AL2M2VY/2T
Label explanation
CAT: Luminous Intensity Rank
HUE: Dom. Wavelength Rank
REF: Forward Voltage Rank
Reel Dimensions
Note: The tolerances unless mentioned is ±0.1mm, Unit = mm
Everlight Electronics Co., Ltd.
http://www.everlight.com
Rev
1
Page: 6 of 10
Device No: SZDSE-151-S04
Prepared date: 25-Mar-2005
Prepared by: Zhang huali
EVERLIGHT ELECTRONICS CO.,LTD.
15-21/S2C-AL2M2VY/2T
Carrier Tape Dimensions: Loaded quantity 2000 PCS per reel
Note: The tolerances unless mentioned is ±0.1mm, Unit = mm
Moisture Resistant Packaging
Label
Aluminum moisture-proof bag
Desiccant
1
Label
Everlight Electronics Co., Ltd.
http://www.everlight.com
Rev
Page: 7 of 10
Device No: SZDSE-151-S04
Prepared date: 25-Mar-2005
Prepared by: Zhang huali
EVERLIGHT ELECTRONICS CO.,LTD.
15-21/S2C-AL2M2VY/2T
Reliability Test Items And Conditions
The reliability of products shall be satisfied with items listed below.
Confidence level:90%
LTPD:10%
No.
Items
Test Condition
1
Reflow Soldering
Temp. : 260℃±5℃
Min.5 sec.
Test
Sample
Ac/Re
Hours/Cycles Size
22 Pcs.
0/1
Temperature Cycle
H : +100℃ 15min
∫ 5 min
L : -40℃ 15min
300 Cycles 22 PCS.
0/1
3
Thermal Shock
H : +100℃ 5min
∫ 10 sec
L : -10℃ 5min
300 Cycles 22 PCS.
0/1
4
High Temperature
Storage
Temp. : 100℃
1000 Hrs.
22 PCS.
0/1
5
Low Temperature
Storage
Temp. : -40℃
1000 Hrs.
22 PCS.
0/1
6
DC Operating Life
IF = 20 mA
1000 Hrs.
22 PCS.
0/1
7
High Temperature /
High Humidity
85℃/85%RH
1000 Hrs.
22 PCS.
0/1
2
6 Min.
Everlight Electronics Co., Ltd.
http://www.everlight.com
Rev
1
Page: 8 of 10
Device No: SZDSE-151-S04
Prepared date: 25-Mar-2005
Prepared by: Zhang huali
EVERLIGHT ELECTRONICS CO.,LTD.
15-21/S2C-AL2M2VY/2T
Precautions For Use
1. Over-current-proof
Customer must apply resistors for protection , otherwise slight voltage shift will cause big
current change ( Burn out will happen ).
2. Storage
2.1 Do not open moisture proof bag before the products are ready to use.
2.2 Before opening the package: The LEDs should be kept at 30℃ or less and 90%RH or less.
2.3After opening the package, the LEDs should be kept at 30℃ or less and 70%RH or less(Floor life).
However,it’s recommended that The LEDs should be used within 168 hours (7 days) after opening
the package.If unused LED remain, it should be stored in moisture proof packages.
2.4 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the
storage time, baking treatment should be performed using the following conditions.
Baking treatment : 60±5℃ for 24 hours.
3. Soldering Condition
3.1 Pb-free solder temperature profile
3.2 Reflow soldering should not be done more than two times.
3.3 When soldering, do not put stress on the LEDs during heating.
3.4 After soldering, do not warp the circuit board.
Everlight Electronics Co., Ltd.
http://www.everlight.com
Rev
1
Page: 9 of 10
Device No: SZDSE-151-S04
Prepared date: 25-Mar-2005
Prepared by: Zhang huali
EVERLIGHT ELECTRONICS CO.,LTD.
15-21/S2C-AL2M2VY/2T
4.Soldering Iron
Each terminal is to go to the tip of soldering iron temperature less than 350℃ for 3 seconds
within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do
soldering of each terminal. Be careful because the damage of the product is often started at the time of
the hand solder.
5.Repairing
Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a
double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether
the characteristics of the LEDs will or will not be damaged by repairing.
EVERLIGHT ELECTRONICS CO., LTD.
Office: No 25, Lane 76, Sec 3, Chung Yang Rd,
Tucheng, Taipei 236, Taiwan, R.O.C
Tel: 886-2-2267-2000, 2267-9936
Fax: 886-2267-6244, 2267-6189, 2267-6306
http://www.everlight.com
Everlight Electronics Co., Ltd.
http://www.everlight.com
Rev
1
Page: 10 of 10
Device No: SZDSE-151-S04
Prepared date: 25-Mar-2005
Prepared by: Zhang huali