EVERLIGHT ELECTRONICS CO.,LTD. Technical Data Sheet Chip LED with Right Angle Lens 12-215/R8C-AN1P2B/3C Features ․Package in 8mm tape on 7〞diameter reel. ․Compatible with automatic placement equipment. ․Compatible with infrared and vapor phase reflow solder process. ․Mono-color type. ․Pb-free. ․The product itself will remain within RoHS compliant version. Descriptions ․The 12-215 SMD Taping is much smaller than lead frame type components, thus enable smaller board size, higher packing density, reduced storage space and finally smaller equipment to be obtained. ․Besides, lightweight makes them ideal for miniature applications. etc. Applications ․Backlighting in dashboard and switch. ․Telecommunication: indicator and backlighting in telephone and fax. ․Flat backlight for LCD, switch and symbol. ․General use. Device Selection Guide Chip Part No. Material Emitted Color 12-215/R8C-AN1P2B/3C AlGaInP Deep-Red Everlight Electronics Co., Ltd. Device No:SZDSE-125-R06 http://www.everlight.com Prepared date: 02-June-2006 Rev 1 Lens Color Water Clear Page: 1 of 10 Prepared by: Wu xiaowei EVERLIGHT ELECTRONICS CO.,LTD. 12-215/R8C-AN1P2B/3C Package Outline Dimensions CL 0.6 CL 1.7 ± 0.2 2.1 ± 0.2 0.5 1.0 ± 0.2 R0.5 1.5 0.5 2.2 Cathode mark 0.9 Note: The tolerances unless mentioned is ±0.1mm, Unit = mm Everlight Electronics Co., Ltd. Device No:SZDSE-125-R06 http://www.everlight.com Prepared date: 02-June-2006 Rev 1 Page: 2 of 10 Prepared by: Wu xiaowei EVERLIGHT ELECTRONICS CO.,LTD. 12-215/R8C-AN1P2B/3C Absolute Maximum Ratings (Ta=25℃) Parameter Symbol Rating Unit Reverse Voltage VR 5 V Forward Current IF 25 mA Operating Temperature Topr -40 ~ +85 ℃ Storage Temperature Tstg -40 ~ +90 ℃ Electrostatic Discharge(HBM) ESD 2000 V Power Dissipation Pd 60 mW IFP 60 mA Peak Forward Current (Duty 1/10 @1KHz) Soldering Temperature Reflow Soldering : 260 ℃ for 10 sec. Tsol Hand Soldering : 350 ℃ for 3 sec. Electro-Optical Characteristics (Ta=25℃) Parameter Symbol Min. Typ. Max. Unit Luminous Intensity IV 28.5 ----- 72.0 mcd Peak Wavelength λp ---- 632 ---- nm Dominant Wavelength λd 629.5 ----- 645.5 nm Spectrum Radiation Bandwidth △λ ----- 20 ---- nm Viewing Angle 2θ1/2 ----- 130 ---- deg Forward Voltage VF 1.75 ----- 2.35 V Reverse Current IR ---- ---- 10 µA Condition IF=20mA VR=5V Notes: 1.Tolerance of Luminous Intensity ±10% 2.Tolerance of Dominant Wavelength ±1nm 3.Tolerance of Forward Voltage ±0.1V Everlight Electronics Co., Ltd. Device No:SZDSE-125-R06 http://www.everlight.com Prepared date: 02-June-2006 Rev 1 Page: 3 of 10 Prepared by: Wu xiaowei EVERLIGHT ELECTRONICS CO.,LTD. 12-215/R8C-AN1P2B/3C Bin Range Of Dom. Wavelength Group A Bin Min Max E7 629.5 633.5 E8 633.5 637.5 E9 637.5 641.5 E10 641.5 645.5 Unit Condition nm IF =20mA Unit Condition mcd IF =20mA Unit Condition V IF =20mA Bin Range Of Luminous Intensity Bin Min Max N1 28.5 36.0 N2 36.0 45.0 P1 45.0 57.0 P2 57.0 72.0 Bin Range Of Luminous Voltage Group B Bin Min Max 0 1.75 1.95 1 1.95 2.15 2 2.15 2.35 Notes: 1.Tolerance of Luminous Intensity ±10% 2.Tolerance of Dominant Wavelength ±1nm 3.Tolerance of Forward Voltage ±0.1V Everlight Electronics Co., Ltd. Device No:SZDSE-125-R06 http://www.everlight.com Prepared date: 02-June-2006 Rev 1 Page: 4 of 10 Prepared by: Wu xiaowei EVERLIGHT ELECTRONICS CO.,LTD. 12-215/R8C-AN1P2B/3C Electro-Optical Characteristics (Ta=25℃) Everlight Electronics Co., Ltd. Device No:SZDSE-125-R06 http://www.everlight.com Prepared date: 02-June-2006 Rev 1 Page: 5 of 10 Prepared by: Wu xiaowei EVERLIGHT ELECTRONICS CO.,LTD. 12-215/R8C-AN1P2B/3C Label explanation CAT: Luminous Intensity Rank HUE: Dom. Wavelength Rank xxxxxx xxxxxx REF: Forward Voltage Rank RoHS xxxxxxxxxxxx xxxx xxxxxxxx Reel Dimensions Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm Everlight Electronics Co., Ltd. Device No:SZDSE-125-R06 http://www.everlight.com Prepared date: 02-June-2006 Rev 1 Page: 6 of 10 Prepared by: Wu xiaowei EVERLIGHT ELECTRONICS CO.,LTD. 12-215/R8C-AN1P2B/3C Carrier Tape Dimensions: Loaded quantity 3000 PCS per reel Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm Moisture Resistant Packaging Label Aluminum moisture-proof bag Everlight Electronics Co., Ltd. Device No:SZDSE-125-R06 http://www.everlight.com Prepared date: 02-June-2006 Desiccant Rev 1 Label Page: 7 of 10 Prepared by: Wu xiaowei EVERLIGHT ELECTRONICS CO.,LTD. 12-215/R8C-AN1P2B/3C Reliability Test Items And Conditions The reliability of products shall be satisfied with items listed below. Confidence level：90% LTPD：10% No. Items Test Condition 1 Reflow Soldering Temp. : 260℃±5℃ Min. 5sec. Temperature Cycle H : +100℃ 15min ∫ 5 min L : -40℃ 15min Thermal Shock H : +100℃ 5min ∫ 10 sec L : -10℃ 5min 2 3 4 5 High Temperature Storage Low Temperature Storage Test Sample Hours/Cycles Size 6 Min. 300 Cycles 300 Cycles Ac/Re 22 PCS. 0/1 22 PCS. 0/1 22 PCS. 0/1 Temp. : 100℃ 1000 Hrs. 22 PCS. 0/1 Temp. : -40℃ 1000 Hrs. 22 PCS. 0/1 6 DC Operating Life IF = 20 mA 1000 Hrs. 22 PCS. 0/1 7 High Temperature / High Humidity 85℃/ 85% RH 1000 Hrs. 22 PCS. 0/1 Everlight Electronics Co., Ltd. Device No:SZDSE-125-R06 http://www.everlight.com Prepared date: 02-June-2006 Rev 1 Page: 8 of 10 Prepared by: Wu xiaowei EVERLIGHT ELECTRONICS CO.,LTD. 12-215/R8C-AN1P2B/3C Precautions For Use 1. Over-current-proof Customer must apply resistors for protection , otherwise slight voltage shift will cause big current change ( Burn out will happen ). 2. Storage 2.1 Do not open moisture proof bag before the products are ready to use. 2.2 Before opening the package: The LEDs should be kept at 30℃ or less and 90%RH or less. 2.3After opening the package, the LEDs should be kept at 30℃ or less and 60%RH or less(Floor life). However,it’s recommended that The LEDs should be used within 168 hours (7 days) after opening the package.If unused LED remain, it should be stored in moisture proof packages. 2.4 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment : 60±5℃ for 24 hours. 3. Soldering Condition 3.1 Pb-free solder temperature profile 3.2 Reflow soldering should not be done more than two times. 3.3 When soldering, do not put stress on the LEDs during heating. 3.4 After soldering, do not warp the circuit board. Everlight Electronics Co., Ltd. Device No:SZDSE-125-R06 http://www.everlight.com Prepared date: 02-June-2006 Rev 1 Page: 9 of 10 Prepared by: Wu xiaowei EVERLIGHT ELECTRONICS CO.,LTD. 12-215/R8C-AN1P2B/3C 4.Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than350℃ for 3 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. 5.Repairing Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. EVERLIGHT ELECTRONICS CO., LTD. Office: No 25, Lane 76, Sec 3, Chung Yang Rd, Tucheng, Taipei 236, Taiwan, R.O.C Everlight Electronics Co., Ltd. Device No:SZDSE-125-R06 Tel: 886-2-2267-2000, 2267-9936 Fax: 886-2267-6244, 2267-6189, 2267-6306 http://www.everlight.com http://www.everlight.com Prepared date: 02-June-2006 Rev 1 Page: 10 of 10 Prepared by: Wu xiaowei