Technical Data Sheet 0603 Package Chip LED (0.4mm Height) 19-217/S2C-AL1M2VY/3T Features ․Package in 8mm tape on 7〞diameter reel. ․Compatible with automatic placement equipment. ․Compatible with infrared and vapor phase reflow solder process. ․Mono-color type. ․Pb-free. ․The product itself will remain within RoHS complaint version Descriptions ․The 19-217 SMD LED is much smaller than lead frame type components, thus enable smaller board size, higher packing density, reduced storage space and finally smaller equipment to be obtained. ․Besides, lightweight makes them ideal for miniature applications. etc. Applications ․Backlighting in dashboard and switch. ․Telecommunication: indicator and backlighting in telephone and fax. ․Flat backlight for LCD, switch and symbol. ․General use. Device Selection Guide Part No. 19-217/S2C-AL1M2VY/3T Everlight Electronics Co., Ltd. Device No: DSE-0001398 Revision :3 LifecyclePhase: Chip Material AlGaInP Emitted Color Resin Color Brilliant Orange Water Clear http://www.everlight.com Rev. 3 Prepared date: 22-Jun-2009 Page: 1 of 10 Prepared by: Zhu lili Release Date:2009-06-23 21:24:04.0 Expired Period: Forever 19-217/S2C-AL1M2VY/3T Package Outline Dimensions Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm Everlight Electronics Co., Ltd. Device No: DSE-0001398 Revision :3 LifecyclePhase: http://www.everlight.com Rev. 3 Prepared date: 22-Jun-2009 Page: 2 of 10 Prepared by: Zhu lili Release Date:2009-06-23 21:24:04.0 Expired Period: Forever 19-217/S2C-AL1M2VY/3T Absolute Maximum Ratings (Ta=25℃) Parameter Symbol Rating Unit Reverse Voltage VR 5 V Forward Current IF 25 mA IFP 60 mA Power Dissipation Pd 60 mW Electrostatic Discharge(HBM) ESD 2000 V Operating Temperature Topr -40 ~ +85 ℃ Storage Temperature Tstg -40 ~ +90 ℃ Soldering Temperature Tsol Peak Forward Current (Duty 1/10 @1KHz) Reflow Soldering : 260 ℃ for 10 sec. Hand Soldering : 350 ℃ for 3 sec. Electro-Optical Characteristics (Ta=25℃) Parameter Symbol Min. Typ. Max. Unit Luminous Intensity Iv 11.5 ----- 28.5 mcd Viewing Angle 2θ1/2 ----- 120 ----- deg Peak Wavelength λp ----- 611 ----- nm Dominant Wavelength λd 600.5 ----- 612.5 nm Spectrum Radiation Bandwidth △λ ----- 17 ----- nm Forward Voltage VF 1.70 ----- 2.20 V Reverse Current IR ----- ----- 10 μA Condition IF=5mA VR=5V Notes: 1.Tolerance of Luminous Intensity ±10% 2.Tolerance of Dominant Wavelength ±1nm 3.Tolerance of Forward Voltage ±0.05V Everlight Electronics Co., Ltd. Device No: DSE-0001398 Revision :3 LifecyclePhase: http://www.everlight.com Rev. 3 Prepared date: 22-Jun-2009 Page: 3 of 10 Prepared by: Zhu lili Release Date:2009-06-23 21:24:04.0 Expired Period: Forever 19-217/S2C-AL1M2VY/3T Bin Range Of Dom. Wavelength Group A Bin Min Max D8 600.5 603.5 D9 603.5 606.5 D10 606.5 609.5 D11 609.5 612.5 Unit Condition nm IF=5mA Unit Condition mcd IF=5mA Unit Condition V IF=5mA Bin Range Of Luminous Intensity Bin Min Max L1 11.5 14.5 L2 14.5 18.0 M1 18.0 22.5 M2 22.5 28.5 Bin Range Of Forward Voltage Group V Bin Min Max 19 1.70 1.80 20 1.80 1.90 21 1.90 2.00 22 2.00 2.10 23 2.10 2.20 Notes: 1.Tolerance of Luminous Intensity ±10% 2.Tolerance of Dominant Wavelength ±1nm 3.Tolerance of Forward Voltage ±0.05V Everlight Electronics Co., Ltd. Device No: DSE-0001398 Revision :3 LifecyclePhase: http://www.everlight.com Rev. 3 Prepared date: 22-Jun-2009 Page: 4 of 10 Prepared by: Zhu lili Release Date:2009-06-23 21:24:04.0 Expired Period: Forever 19-217/S2C-AL1M2VY/3T Typical Electro-Optical Characteristics Curves Forward Current vs. Forward Voltage Spectrum Distribution Ta=25°C 75 50 25 0 500 550 600 650 Wavelength λ (nm) 700 Forward Voltage VF (V) Relative Luminous Intensity vs. Forward Current Ta=25°C 1000 Relative luminous intensity (%) Relative luminous intensity (%) Relative Luminous Intensity vs. Ambient Temperature 100 10 1 -60 -40 -20 0 20 40 60 80 100 1000 f=1KHz Duty=1/10 100 10 1 0 10 Ambient Temperature T a (°C) 2 1 10 10 Forward Current I F (mA) Radiation Diagram Forward Current Derating Curve 0° 40 Forward Current I F (mA) Ta=25°C Forward Current I F (mA) Relative luminous intensity (%) 100 10° 3 10 Ta=25°C 20° 30° 30 40° 1.0 20 0.9 50° 0.8 60° 10 70° 0.7 0 0 20 40 60 80 100 80° 90° 0.5 0.3 0.1 0.2 0.4 0.6 Ambient Temperature T a (°C) Everlight Electronics Co., Ltd. Device No: DSE-0001398 Revision :3 LifecyclePhase: http://www.everlight.com Rev. 3 Prepared date: 22-Jun-2009 Page: 5 of 10 Prepared by: Zhu lili Release Date:2009-06-23 21:24:04.0 Expired Period: Forever 19-217/S2C-AL1M2VY/3T Label explanation CAT: Luminous Intensity Rank HUE: Dom. Wavelength Rank REF: Forward Voltage Rank Pb EVERLIGHT CPN : P N : XXXXXXXXXXXXX RoHS XXXXXXXXXXXXX CAT : XXX HUE : XXX REF : XXX QTY : XXX LOT NO : XXXXXXXXXX Reference : XXXXXXXX MADE IN TAIWAN Reel Dimensions Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm Everlight Electronics Co., Ltd. Device No: DSE-0001398 Revision :3 LifecyclePhase: http://www.everlight.com Rev. 3 Prepared date: 22-Jun-2009 Page: 6 of 10 Prepared by: Zhu lili Release Date:2009-06-23 21:24:04.0 Expired Period: Forever 19-217/S2C-AL1M2VY/3T Carrier Tape Dimensions: Loaded quantity 3000 PCS per reel Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm Moisture Resistant Packaging Label Aluminum moisture-proof bag Everlight Electronics Co., Ltd. Device No: DSE-0001398 Revision :3 LifecyclePhase: Desiccant http://www.everlight.com Label Rev. 3 Prepared date: 22-Jun-2009 Page: 7 of 10 Prepared by: Zhu lili Release Date:2009-06-23 21:24:04.0 Expired Period: Forever 19-217/S2C-AL1M2VY/3T Reliability Test Items And Conditions The reliability of products shall be satisfied with items listed below. Confidence level：90% LTPD：10% Ac/Re Items Test Condition 1 Reflow Soldering Temp. : 260℃±5℃ Min. 5sec. 6 Min. 22 PCS. 0/1 Temperature Cycle H : +100℃ 15min ∫ 5 min L : -40℃ 15min 300 Cycles 22 PCS. 0/1 Thermal Shock H : +100℃ 5min ∫ 10 sec L : -10℃ 5min 300 Cycles 22 PCS. 0/1 Temp. : 100℃ 1000 Hrs. 22 PCS. 0/1 Temp. : -40℃ 1000 Hrs. 22 PCS. 0/1 2 3 High Temperature Storage Low Temperature Storage 4 5 6 DC Operating Life IF = 20 mA 1000 Hrs. 22 PCS. 0/1 7 High Temperature / High Humidity 85℃/ 85%RH 1000 Hrs. 22 PCS. 0/1 Everlight Electronics Co., Ltd. Device No: DSE-0001398 Revision Test Sample Hours/Cycles Size No. :3 LifecyclePhase: http://www.everlight.com Rev. 3 Prepared date: 22-Jun-2009 Page: 8 of 10 Prepared by: Zhu lili Release Date:2009-06-23 21:24:04.0 Expired Period: Forever 19-217/S2C-AL1M2VY/3T Precautions For Use 1. Over-current-proof Customer must apply resistors for protection, otherwise slight voltage shift will cause big current change ( Burn out will happen ). 2. Storage 2.1 Do not open moisture proof bag before the products are ready to use. 2.2 Before opening the package: The LEDs should be kept at 30℃ or less and 90%RH or less. 2.3 After opening the package: The LED's floor life is 1 year under 30℃ or less and 60% RH or less. If unused LEDs remain, it should be stored in moisture proof package 2.4 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment : 60±5℃ for 24 hours. 3. Soldering Condition 3.1 Pb-free solder temperature profile 3.2 Reflow soldering should not be done more than two times. 3.3 When soldering, do not put stress on the LEDs during heating. 3.4 After soldering, do not warp the circuit board. Everlight Electronics Co., Ltd. Device No: DSE-0001398 Revision :3 LifecyclePhase: http://www.everlight.com Rev. 3 Prepared date: 22-Jun-2009 Page: 9 of 10 Prepared by: Zhu lili Release Date:2009-06-23 21:24:04.0 Expired Period: Forever 19-217/S2C-AL1M2VY/3T 4.Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 350℃ for 3 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. 5.Repairing Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. EVERLIGHT ELECTRONICS CO., LTD. Office: No 25, Lane 76, Sec 3, Chung Yang Rd, Tucheng, Taipei 236, Taiwan, R.O.C Everlight Electronics Co., Ltd. Device No: DSE-0001398 Revision :3 LifecyclePhase: Tel: 886-2-2267-2000, 2267-9936 Fax: 886-2267-6244, 2267-6189, 2267-6306 http://www.everlight.com http://www.everlight.com Rev. 3 Prepared date: 22-Jun-2009 Page: 10 of 10 Prepared by: Zhu lili Release Date:2009-06-23 21:24:04.0 Expired Period: Forever