for FIBRE HCMOS 7 x 5mm CHANNEL 3.3V 50ppm Model: FXO-HC735RFC-106.25 XO Freq: 106.25MHz Features Low Jitter Low Cost Tri-State Enable / Disable Feature Industry Standard Package Gold over Nickel Termination Finish V DD Enable / Disable FOX X PRESSO OUTPUT ASICs GND Electrical Characteristics Parameters Frequency Symbol Condition FO 106.25 MHz Frequency Stability 1 Temperature Range Supply Voltage TO TSTG VDD Input Current IDD Output Load HCMOS Start-Up Time Standard operating Storage Standard Standard Load Standard Operational TS Output Enable / Disable Time Moisture Sensitivity Level Termination Finish Maximum Value (unless otherwise noted) 50 ppm -40°C to +85°C -55°C to +125°C 3.3V ± 5% 44 mA 15 pF 30 pF 10 mS 100 nS MSL 1 Au Note 1 – Stability is inclusive of 25°C tolerance, operating temperature range, input voltage change, load change, aging, shock and vibration. Output Wave Characteristics Parameters Symbol Output LOW Voltage Output HIGH Voltage Output Symmetry VOL VOH Output Enable (PIN # 1) Voltage VIH Output Disable (PIN # 1) Voltage Cycle Rise Time Cycle Fall Time VIL TR TF Condition Standard Load Standard Load @ 50% VDD Level Maximum Value (unless otherwise noted) 10% VDD 90% VDD MIN 45% ~ 55% ≥70% VDD 10% ~ 90% VDD 90% ~ 10% VDD ≤30% VDD 3 nS 3 nS DWG-100747 | Rev. 07/13/2010 Page 1 of 2 FOXElectronics 5570 Enterprise Parkway Fort Myers, Florida 33905 USA +1.239.693.0099 FAX +1.239.693.1554 FOXONLINE EMEA Tel/Fax: +44 .1767.312632 | Asia Hong Kong Tel: +852.2854.4285 Fax +852.2854.4282 | Japan Tel: +81.3.3374.2079 Fax: +81.3.3374.5221 © 2010 FOX ELECTRONICS | ISO9001:2000 Certified for FIBRE HCMOS 7 x 5mm CHANNEL 3.3V 50ppm Model: FXO-HC735RFC-106.25 XO Freq: 106.25MHz Dimensional Drawing & Pad Layout 0.01 F E/D #1 NC GND VDD #4 NC #2 OUT #3 HCMOS LOAD (15 pF) Phase Jitter & Time Interval Error (TIE) (Typical Measurements) Frequency Phase Jitter TIE (12kHz to 20MHz) (Sigma of Jitter Distribution) Units 106.25 MHz 0.86 3.2 pS RMS Phase Jitter is integrated from HP3048 Phase Noise Measurement System; measured directly into 50 ohm input; VDD = 3.3V. TIE was measured on LeCroy LC684 Digital Storage Scope, directly into 50 ohm input, with Amherst M1 software; VDD = 3.3V. Per MJSQ spec (Methodologies for Jitter and Signal Quality specifications) Random & Deterministic Jitter Composition (Typical Measurements) Frequency 106.25 MHz Random (Rj) Deterministic (Dj) (pS RMS) (pS P-P) 1.28 8.4 Total Jitter (Tj) (14 x Rj) + Dj 26.6 pS Rj and Dj, measured on LeCroy LC684 Digital Storage Scope, directly into 50 ohm input, with Amherst M1 software. Per MJSQ spec (Methodologies for Jitter and Signal Quality specifications) Pin Functional Description Pin # Name Type 1 1 2 3 4 E/D GND Output VDD Test Points 2 N. C. Logic Ground Output Power Hi Z Function Enable / Disable Control of Output (0 = Disabled) Electrical Ground for VDD HCMOS Oscillator Output Power Supply Source Voltage No Connection (Factory Use ONLY) NOTES: 1 2 DWG-100747 | Includes pull-up resistor to VDD to provide output when the pin (1) is No Connect. Installation should include a 0.01µF bypass capacitor placed between VDD (Pin 4) and GND (Pin 2) to minimize power supply line noise. Rev. 07/10/2010 Page 2 of 2 © 2010 FOX ELECTRONICS | ISO9001:2000 Certified | FOXONLINE