ETHERNET for LVPECL 7 x 5mm 3.3V Model: FXO-PC735RGB-125 50ppm XO Freq: 125MHz Features Low Jitter Low Cost Tri-State Enable / Disable Feature Industry Standard Package Gold over Nickel Termination Finish V DD Enable / Disable FOX X PRESSO OUTPUT ASICs GND Electrical Characteristics Parameters Frequency Symbol Condition FO 125 MHz Frequency Stability 1 Temperature Range Supply Voltage TO TSTG VDD Input Current IDD Output Load Differential Start-Up Time Standard operating Storage Standard Standard Load Standard TS 50 ppm -40°C to +85°C -55°C to +125°C 3.3V ± 5% 120 mA 50 ohms into VDD -2.0VDC 10 mS Output Enable / Disable Time Moisture Sensitivity Level Termination Finish Maximum Value (unless otherwise noted) 100 nS MSL 1 Au Note 1 – Stability is inclusive of 25°C tolerance, operating temperature range, input voltage change, load change, aging, shock and vibration. Output Wave Characteristics Parameters Symbol Condition Standard Load Standard Load @ 50% Vp-p Level Maximum Value Output LOW Voltage Output HIGH Voltage Output Symmetry VOL VOH Output Enable (PIN # 1) Voltage VIH ≥70% VDD Output Disable (PIN # 1) Voltage Cycle Rise Time Cycle Fall Time VIL TR TF ≤30% VDD 400 pS 400 pS 20% ~ 80% Vp-p 80% ~ 20% Vp-p 1.35V ~ 1.65V 2.055V ~ 2.405V 45% ~ 55% DWG-100722 | Rev. 6/2/2010 Page 1 of 2 FOXElectronics 5570 Enterprise Parkway Fort Myers, Florida 33905 USA +1.239.693.0099 FAX +1.239.693.1554 FOXONLINE EMEA Tel/Fax: +44 .1767.312632 | Asia Hong Kong Tel: +852.2854.4285 Fax +852.2854.4282 | Japan Tel: +81.3.3374.2079 Fax: +81.3.3374.5221 © 2010 FOX ELECTRONICS | ISO9001:2000 Certified ETHERNET for LVPECL 7 x 5mm Model: FXO-PC735RGB-125 50ppm XO Freq: 125MHz 3.3V Dimensional Drawing & Pad Layout Phase Jitter & Time Interval Error (TIE) (Typical Measurements) Frequency Phase Jitter TIE (12kHz to 20MHz) (Sigma of Jitter Distribution) Units 125 MHz 1.01 3.1 pS RMS Phase Jitter is integrated from HP3048 Phase Noise Measurement System; measured directly into 50 ohm input; VDD = 3.3V. TIE was measured on LeCroy LC684 Digital Storage Scope, directly into 50 ohm input, with Amherst M1 software; VDD = 3.3V. Per MJSQ spec (Methodologies for Jitter and Signal Quality specifications) Random & Deterministic Jitter Composition (Typical Measurements) Frequency Random (Rj) Deterministic (Dj) (pS RMS) (pS P-P) 1.27 8.1 125 MHz Total Jitter (Tj) (14 x Rj) + Dj 26.2 pS Rj and Dj, measured on LeCroy LC684 Digital Storage Scope, directly into 50 ohm input, with Amherst M1 software. Per MJSQ spec (Methodologies for Jitter and Signal Quality specifications) Pin Functional Description Pin # 1 2 3 4 5 6 NOTES: Name E/D NC Type 1 2 GND Output Output 2 VDD 3 1 2 3 Logic Function Enable / Disable Control of Output (0 = Disabled) No Connection – Leave Open Ground Output Output Power Electrical Ground for VDD LVPECL Oscillator Output Complementary LVPECL Output Power Supply Source Voltage Includes pull-up resistor to VDD to provide output when the pin (1) is No Connect. (Also see note 2) An optional pin # 2 Enable / disable is available. Installation should include a 0.01µF bypass capacitor placed between VDD (Pin 6) and GND (Pin 3) to minimize power supply line noise. DWG-100722 | Rev. 6/2/2010 Page 2 of 2 © 2010 FOX ELECTRONICS | ISO9001:2000 Certified | FOXONLINE