HMC853LC3 v00.1111 High Speed Logic - SMT 28 Gbps, D-TYPE FLIP-FLOP w/ PROGRAMMABLE OUTPUT VOLTAGE Typical Applications Features The HMC853LC3 is ideal for: Differential & Single-Ended Operation • RF ATE Applications Fast Rise and Fall Times: 15/14 ps • Broadband Test & Measurement Low Power Consumption: 240 mW typ. • Serial Data Transmission up to 28 Gbps Programmable Differential Output Voltage Swing: 700 - 1300 mVp-p • Digital Logic Systems up to 28 GHz Single Supply: -3.3 V 16 Lead Ceramic 3x3 mm SMT Package: 9 mm 2 Functional Diagram General Description The HMC853LC3 is a D-Type Flip-Flop designed to support data transmission rates of up to 28 Gbps, and clock frequencies as high as 28 GHz. During normal operation, data is transferred to the outputs on the positive edge of the clock. Reversing the clock inputs allows for negative-edge triggered applications. All differential inputs to the HMC853LC3 are CML and terminated on-chip with 50 Ohms to the positive supply, Vcc, and may be AC or DC coupled. The differential CML outputs are source terminated to 50 Ohms and may also be AC or DC coupled. Outputs can be connected directly to a 50 Ohm Vcc-terminated system, while DC blocking capacitors may be used if the terminating system is 50 Ohms to ground. The HMC853LC3 also features an output level control pin, VR, which allows for loss compensation or signal-level optimazation. the HMC853LC3 operates from a single 3.3 V supply and is available in ROHS-compliant 3x3 mm SMT package. Electrical Specifications, TA = 25 °C, Vee = -3.3 V, VR = 0 V Parameter Conditions Power Supply Voltage Typ. Max -3.6 -3.3 -3.0 Units V Power Supply Current 73 mA Maximum Data Rate 28 Gbps Maximum Clock Rate 28 GHz Input Voltage Range -1.5 0.5 V Input Differential Voltage 0.1 2.0 Vp-p Input Return Loss, Output Return Loss Output Amplitude Output High Voltage 1 Min. Frequency <24 GHz 10 dB Single-Ended, peak-to-peak 550 mVp-p Differential, peak-to-peak 1100 mVp-p -10 mV For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] HMC853LC3 v00.1111 28 Gbps, D-TYPE FLIP-FLOP w/ PROGRAMMABLE OUTPUT VOLTAGE Electrical Specifications (continued) Conditions Min. Typ. Output Low Voltage Output Return Loss mV Differential, 20% - 80% 15 / 14 ps Frequency <24 GHz 10 dB Random Jitter Jr rms Deterministic Jitter, Jd 0.2 ps rms peak-to-peak, 215 -1 PRBS input [1] 2 101 ps 28 GHz 300 deg 4 ps Propagation Delay Clock to Data, td Clock Phase Margin Set Up Time, ts Hold Time, th VR Pin Current VR = 0.0 V VR Pin Current VR = 0.4 V ps, p-p 3 ps 2.5 mA 4 mA Output Differential Voltage vs. Supply Voltage [1][2] DC Current vs. Supply Voltage [1][2] 100 1500 95 85 VOUT DIFFERENTIAL (mVp-p) +25C +85C -40C Vr= -0.4V Vr= +0.4V 90 DC CURRENT (mA) Units -560 Output Rise / Fall Time 80 75 70 65 60 55 50 -3.7 Max 1400 1300 1200 1100 1000 900 800 +25C +85C -40C Vr= -0.4V Vr= +0.4V 700 600 -3.6 -3.5 -3.4 -3.3 -3.2 -3.1 -3 500 -3.7 -2.9 High Speed Logic - SMT Parameter -3.6 -3.5 SUPPLY VOLTAGE (V) -3.4 -3.3 -3.2 -3.1 -3 -2.9 SUPPLY VOLTAGE (V) Output Differential Voltage vs. VR [2][3] VOUT DIFFERENTIAL (mVp-p) 1500 1400 1300 +25C +85C -40C 1200 1100 1000 900 800 700 600 500 -1.2 -1 -0.8 -0.6 -0.4 -0.2 0 0.2 0.4 VR (V) [1] VR = 0.0 V [2] Frequency = 13 GHz [3] Vee = -3.3 V For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] 2 HMC853LC3 v00.1111 28 Gbps, D-TYPE FLIP-FLOP w/ PROGRAMMABLE OUTPUT VOLTAGE Rise / Fall Time vs. Supply Voltage [1][2] Rise / Fall Time vs. VR [2][4] 20 tr tf 16 14 12 16 14 12 10 -3.7 -3.6 -3.5 -3.4 -3.3 -3.2 -3.1 -3 10 -1.2 -2.9 -1 -0.8 -0.6 -0.4 -0.2 0 0.2 0.4 VR (V) SUPPLY VOLTAGE (V) Input Return Loss vs. Frequency [1][3][4] Output Return Loss vs. Frequency [1][3][4] 0 0 Eval Board Device Eval Board Device -5 RETURN LOSS (dB) -5 -10 -15 -20 -25 -10 -15 -20 -25 -30 -30 0 3 6 9 12 15 18 FREQUENCY (GHz) [1] VR = 0.0 V [4]Vee = -3.3 V 3 tr tf 18 RISE/FALL TIME (ps) RISE/FALL TIME (ps) 18 RETURN LOSS (dB) High Speed Logic - SMT 20 [2] Frequency = 13 GHz 21 24 27 0 3 6 9 12 15 18 21 24 27 FREQUENCY (GHz) [3] Device measured on evaluation board with single-ended time domain gating. For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] HMC853LC3 v00.1111 28 Gbps, D-TYPE FLIP-FLOP w/ PROGRAMMABLE OUTPUT VOLTAGE Parameter Conditions Bit Rate 24.9900 Gbps Pattern Length 127 Bits DJ (d-d) 2.0 ps Vertical Scale 100 mV / div Time Scale 6.7 ps / div Test Conditions: Pattern generated with a 27-1 PN generator at 25 GHz. Measured using an Agilent 86100C 33 GHz DCA. Single-ended 550 mV data and 400 mV clock inputs. Timing Diagram tc = High Speed Logic - SMT Eye Diagram @ 25 Gbps I fclock tSH = Setup and Hold Time CPM = Clock Phase Margin = 360° tc - tSH tc Truth Table Input Outputs D C L L -> H L H L -> H H Notes: D = DP - DN C = CP - CN Q = QP - QN Q H - Positive Difference Voltage L - Negative Difference Voltage For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] 4 HMC853LC3 v00.1111 28 Gbps, D-TYPE FLIP-FLOP w/ PROGRAMMABLE OUTPUT VOLTAGE High Speed Logic - SMT Absolute Maximum Ratings Power Supply Voltage (Vee) -3.75 V to +0.5 V Input Signals -2 V to +0.5 V Output Signals -1.5 V to +1 V Continuous Pdiss (T = 85 °C) (derate 17 mW/°C above 85 °C) 0.68 W Thermal Resistance (Rth l-p) Worst Case Junction to Package Paddle 59 °C/W Maximum Junction Temperature 125 °C Storage Temperature -65 °C to +150 °C Operating Temperature -40 °C to +85 °C ESD Sensitivity (HBM) Class 1C ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS Outline Drawing NOTES: 1. PACKAGE BODY MATERIAL: ALUMINA 2. LEAD AND GROUND PADDLE PLATING: 30-80 MICROINCHES GOLD OVER 50 MICROINCHES MINIMUM NICKEL. 3. DIMENSIONS ARE IN INCHES [MILLIMETERS]. 4. LEAD SPACING TOLERANCE IS NON-CUMULATIVE. 5. PACKAGE WARP SHALL NOT EXCEED 0.05 mm DATUM -C6. ALL GROUND LEADS MUST BE SOLDERED TO PCB RF GROUND. 7. PADDLE MUST BE SOLDERED TO Vee. 5 For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] HMC853LC3 v00.1111 28 Gbps, D-TYPE FLIP-FLOP w/ PROGRAMMABLE OUTPUT VOLTAGE Pin Descriptions Function Description 1, 4, 5, 8, 9, 12 GND Signal Grounds 2, 3 6, 7 DN, DP CP, CN Differential Data Inputs: Current Mode Logic (CML) referenced to positive supply 10, 11 QP, QN Differential Data Outputs: Current Mode Logic (CML) referenced to positive supply. 13, 16 GND Supply Ground 14 VR Output level control. Output level may be increased or decreased by applying a voltage to VR per “Output Differential vs. VR” plot. 15, Package Base Vee This pin and the exposed paddle must be connected to the negative voltage supply. Interface Schematic For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] High Speed Logic - SMT Pin Number 6 HMC853LC3 v00.1111 28 Gbps, D-TYPE FLIP-FLOP w/ PROGRAMMABLE OUTPUT VOLTAGE High Speed Logic - SMT Evaluation PCB List of Materials for Evaluation PCB 125614 [1] Item Description J1 - J6 PCB Mount K RF Connectors J7 - J9 DC Pin C1, C2 100 pF Capacitor, 0402 Pkg. C3, C4 4.7 µF Capacitor, Tantalum R1 10 Ohm Resistor, 0603 Pkg. U1 HMC853LC3 High Speed Logic, D-Type Flip-Flop PCB [2] 125612 Evaluation Board [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Arlon 25FR or Rogers 4350 7 The circuit board used in the application should use RF circuit design techniques. Signal lines should have 50 Ohm impedance while the package ground leads should be connected directly to the ground plane similar to that shown. The exposed metal package base must be connected to Vee. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request. Install jumper on JP1 to short VR to GND for normal operation. For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] HMC853LC3 v00.1111 28 Gbps, D-TYPE FLIP-FLOP w/ PROGRAMMABLE OUTPUT VOLTAGE High Speed Logic - SMT Application Circuit For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] 8