HMC721LP3E v01.1010 14 Gbps, FAST RISE TIME XOR / XNOR GATE w/ PROGRAMMABLE OUTPUT VOLTAGE HIGH SPEED LOGIC - SMT 3 Typical Applications Features The HMC721LP3E is ideal for: Inputs Terminated Internally in 50 Ohms • 16 G Fiber Channel Differential or Single-Ended Operation • RF ATE Applications Fast Rise and Fall Times: 19 / 18 ps • Broadband Test & Measurement Low Power Consumption: 230 mW typ. • Serial Data Transmission up to 14 Gbps Programmable Differential Output Voltage Swing: 600 - 1200 mVp-p • Digital Logic Systems up to 14 GHz Propagation Delay: 95 ps Single Supply: -3.3 V 16 Lead 3x3 mm SMT Package: 9 mm2 Functional Diagram General Description The HMC721LP3E is a XOR/XNOR gate function designed to support data transmission rates of up to 14 Gbps, and clock frequencies as high as 14 GHz. All differential inputs to the HMC721LP3E are CML and terminated on-chip with 50 Ohms to the positive supply, GND, and may be DC or AC coupled. Outputs can be connected directly to a 50 Ohm ground-terminated system or drive devices with CML logic input. The HMC721LP3E also features an ouput level control pin, VR, which allows for loss compensation or signal level optimization. The HMC721LP3E operates from a single -3.3 V supply and is available in ROHS-compliant 3x3 mm SMT package.. Electrical Specifi cations, TA = +25 °C, Vee = -3.3 V, VR = 0 V Parameter Conditions Power Supply Voltage Min. Typ. Max -3.6 -3.3 -3.0 Units V Power Supply Current 70 mA Maximum Data Rate 14 Gbps Maximum Clock Rate 14 GHz Input Voltage Range -1.5 0.5 V Input Differential Range 0.1 2.0 Vp-p Input Return Loss Frequency <14 GHz 10 dB Single-Ended, peak-to-peak 550 mVp-p Differential, peak-to-peak 1100 mVp-p Output High Voltage -10 mV Output Low Voltage -560 mV 19 / 18 ps Output Amplitude Output Rise / Fall Time 3-1 Differential, 20% - 80% For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] HMC721LP3E v01.1010 14 Gbps, FAST RISE TIME XOR / XNOR GATE w/ PROGRAMMABLE OUTPUT VOLTAGE Electrical Specifi cations (continued) Conditions Min. Typ. Frequency <13 GHz Max Units 10 Small Signal Gain dB 27 Random Jitter Jr dB rms 0.2 peak-to-peak, 215 -1 PRBS input [1] Deterministic Jitter, Jd 2 Propagation Delay, td VR Pin Current VR = 0.0 V VR Pin Current VR = +0.4 V 3 ps rms ps, pp 95 ps 2 mA 3.5 HIGH SPEED LOGIC - SMT Parameter Output Return Loss mA [1] Deterministic jitter calculated by simultaneously measuring the jitter of a 300 mV, 13 GHz, 215 -1 PRBS input, and a single-ended output DC Current vs. Supply Voltage Output Differential Voltage vs. Supply Voltage [1][3] [1][2] 85 DC CURRENT (mA) 80 VOUT DIFFERENTIAL (mVp-p) 1500 +25C +85C -40C 75 70 65 60 55 -3.7 -3.6 -3.5 -3.4 -3.3 -3.2 -3.1 SUPPLY VOLTAGE (V) -3 -2.9 +25C +85C -40C 1400 1300 1200 1100 1000 -3.7 -3.6 -3.5 -3.4 -3.3 -3.2 -3.1 -3 -2.9 SUPPLY VOLTAGE (V) Rise / Fall Time vs. VR [2][4] Output Differential Voltage vs. VR [3][4] 25 RISE/FALL TIME (ps) 23 VOUT DIFFERENTIAL (mVp-p) 1400 tr tf 21 19 17 1300 +25C +85C -40C 1200 1100 1000 900 800 700 15 -1.2 -1 -0.8 -0.6 -0.4 VR (V) -0.2 0 0.2 0.4 600 -1.2 -1 -0.8 -0.6 -0.4 -0.2 0 0.2 0.4 VR (V) [1] VR = 0.0 V [2] Frequency = 13 GHz [3] Frequency = 10 GHz [4] Vee = -3.3 V For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] 3-2 HMC721LP3E v01.1010 14 Gbps, FAST RISE TIME XOR / XNOR GATE w/ PROGRAMMABLE OUTPUT VOLTAGE Rise / Fall Time vs. Supply Voltage [1][2] Output Differential Voltage vs. Frequency [1][3] 25 tr tf 21 19 17 15 -3.7 -3.6 -3.5 -3.4 -3.3 -3.2 -3.1 -3 1100 1000 900 800 700 -2.9 6 8 10 12 INPUT FREQUENCY (GHz) 14 16 Output Return Loss vs. Frequency Input Return Loss vs. Frequency -10 -15 -15 RETURN LOSS (dB) -10 -20 -25 -30 -35 -20 -25 -30 -35 -40 -40 0 2 4 6 8 10 12 14 FREQUENCY (GHz) [1] VR = 0.0 V 3-3 1200 SUPPLY VOLTAGE (V) RETURN LOSS (dB) HIGH SPEED LOGIC - SMT 3 RISE/FALL TIME (ps) 23 VOUT DIFFERENTIAL (mVp-p) 1300 [2] Frequency = 13 GHz 0 2 4 6 8 10 12 14 FREQUENCY (GHz) [3] Vee = -3.3 V For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] HMC721LP3E v01.1010 14 Gbps, FAST RISE TIME XOR / XNOR GATE w/ PROGRAMMABLE OUTPUT VOLTAGE Eye Diagram 3 HIGH SPEED LOGIC - SMT [1] Test Conditions: Waveform generated with an Agilent N4903A J-Bert. Rate = 10 Gbps. Eye diagram data presented on a Tektronix CSA 8000 Timing Diagram Truth Table Input A Notes: A = AP - AN B = BP - BN D = DP - DN Outputs B D L L L L H H H L H H H L H - Positive voltage level L - Negative voltage level For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] 3-4 HMC721LP3E v01.1010 14 Gbps, FAST RISE TIME XOR / XNOR GATE w/ PROGRAMMABLE OUTPUT VOLTAGE Absolute Maximum Ratings HIGH SPEED LOGIC - SMT 3 Power Supply Voltage (Vee) -3.75 V to +0.5 V Input Signals -2 V to +0.5 V Output Signals -1.5 V to +1 V Junction Temperature 125 °C Continuous Pdiss (T = 85 °C) (derate 20.4 mW/°C above 85 °C) 0.816 W Thermal Resistance (Rthj-p) Worst case junction to package paddle 49 °C/W Storage Temperature -65 °C to +150 °C Operating Temperature -40 °C to +85 °C ESD Sensitivity (HBM) Class 1A ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS Outline Drawing NOTES: 1. LEADFRAME MATERIAL: COPPER ALLOY 2. DIMENSIONS ARE IN INCHES [MILLIMETERS] 3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE 4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM. PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM. 5. PACKAGE WARP SHALL NOT EXCEED 0.05mm. 6. ALL GROUND LEADS MUST BE SOLDERED TO PCB RF GROUND. 7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED LAND PATTERN. 8. PADDLE MUST BE SOLDERED TO Vee. Package Information Part Number Package Body Material Lead Finish HMC721LP3E RoHS-compliant Low Stress Injection Molded Plastic 100% matte Sn MSL Rating MSL1 [2] Package Marking [3] 721 XXXX [1] Max peak reflow temperature of 235 °C [2] Max peak reflow temperature of 260 °C [3] 4-Digit lot number XXXX 3-5 For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] HMC721LP3E v01.1010 14 Gbps, FAST RISE TIME XOR / XNOR GATE w/ PROGRAMMABLE OUTPUT VOLTAGE Pin Descriptions Pin Number Function Description 1, 4, 5, 8, 9, 12 GND Signal Grounds Interface Schematic 2, 3 6, 7 AN, AP BP, BN Differential Clock / Data Inputs: Current Mode Logic (CML) referenced to positive supply 10, 11 DN, DP Differential Clock / Data Outputs: Current Mode Logic (CML) referenced to positive supply 13, 16 GND Supply Ground 14 VR Output level control. Output level may be adjusted by either applying a voltage to VR per “Output Differential vs. VR” plot. Vee Negative Supply 15, Package Base For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] HIGH SPEED LOGIC - SMT 3 3-6 HMC721LP3E v01.1010 14 Gbps, FAST RISE TIME XOR / XNOR GATE w/ PROGRAMMABLE OUTPUT VOLTAGE Evaluation PCB HIGH SPEED LOGIC - SMT 3 List of Materials for Evaluation PCB 118777 [1] Item Description J1 - J6 PCB Mount SMA RF Connectors J7 - J9 DC Pin JP1 0.1” Header with Shorting Jumper C1, C2 100 pF Capacitor, 0402 Pkg. C3, C4 4.7 μF Capacitor, Tantalum R1 10 Ohm Resistor, 0603 Pkg. U1 HMC721LP3E High Speed Logic, XOR / XNOR PCB [2] 118775 Evaluation Board [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Arlon 25FR or Rogers 4350 3-7 The circuit board used in the application should use RF circuit design techniques. Signal lines should have 50 Ohm impedance while the package ground leads should be connected directly to the ground plane similar to that shown. The exposed package base should be connected to Vee. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request. Install jumper on JP1 to short VR to GND for normal operation. For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] HMC721LP3E v01.1010 14 Gbps, FAST RISE TIME XOR / XNOR GATE w/ PROGRAMMABLE OUTPUT VOLTAGE Application Circuit HIGH SPEED LOGIC - SMT 3 For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] 3-8