HMC892LP5E v00.0910 FILTERS - TUNABLE - SMT 3 FILTER - TUNABLE, BAND PASS SMT 4.0 - 7.7 GHz Typical Applications Features The HMC892LP5E is ideal for: Fast Tuning Response; 200 ns • Test & Measurement Equipment Excellent Wideband Rejection; >30 dB • Military RADAR & EW/ECM Single Chip Replacement for Mechanically Tuned Designs • SATCOM & Space • Industrial & Medical Equipment 32 Lead 5x5 mm SMT Package General Description Functional Diagram The HMC892LP5E is a MMIC band pass filter which features a user selectable passband frequency. The 3 dB filter bandwidth is approximately 9%. The 20 dB filter bandwidth is approximately 23%. The center frequency can be varied between 4 and 7.7 GHz by applying an analog tune voltage between 0 and 14V. This tunable filter can be used as a much smaller alternative to physically large switched filter banks and cavity tuned filters. The HMC892LP5E has excellent microphonics due to the monolithic design, and provides a dynamically adjustable solution in advanced communications applications. Electrical Specifications, TA = +25°C, Vfctl = Vbwctl Unless Otherwise Stated Parameter Fcenter Tuning Range Min. Typ. 4 3 dB Bandwidth Max. Units 7.7 GHz 9 % Low Side Rejection Frequency (Rejection >20 dB) 0.9*Fcenter GHz High Side Rejection Frequency (Rejection >20 dB) 1.13*Fcenter GHz Re-entry Frequency (Rejection <30 dB) 2.5*Fcenter GHz 3 dB Bandwidth Control (Vbwctl) ±3 % Insertion Loss 8 dB Return Loss 9 Maximum Input Power for Linear Operation Frequency Control Voltage (Vfctl) 0 Source/Sink Current (Ifctl) Bandwidth Control Voltage (Vbwctl) dB 10 0 Source/Sink Current (Ibwctl) dBm 14 V ±1 mA 14 V ±1 mA Residual Phase Noise [1] (1 MHz Offset) -165 dBc/Hz Fcenter Drift Rate -0.65 MHz/°C Tuning Characteristics [2] tFULLBAND (0% Vfctl to 90% RF) 200 ns [1] Optimum residual phase noise performance requires the use of a low noise driver circuit. [2] Tuning speed is dependent on driver circuit. Data measured with a high speed op-amp driver and includes driver slew rate delay. 3-1 For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] HMC892LP5E v00.0910 FILTER - TUNABLE, BAND PASS SMT 4.0 - 7.7 GHz Broadband Insertion Loss vs. Control Voltages, Vfctl = Vbwctl 0V 7V 14V -5 RETURN LOSS (dB) -10 -20 -30 -40 -50 -10 S11 S22 -15 -20 0V -25 -60 7V 14V -30 -70 0 5 10 15 20 25 0 30 5 10 FREQUENCY (GHz) 15 20 25 30 8 9 FREQUENCY (GHz) Insertion Loss vs. Control Voltages, Vfctl = Vbwctl Return Loss vs. Control Voltages, Vfctl = Vbwctl 0 0 -5 -4 -6 RETURN LOSS (dB) INSERTION LOSS (dB) -2 0V 7V 14V -8 -10 -12 -14 -16 FILTERS - TUNABLE - SMT 0 0 INSERTION LOSS (dB) 3 Broadband Return Loss vs. Control Voltages, Vfctl = Vbwctl -10 -15 7V 0V 14V -20 S11 S22 -25 -18 -30 -20 3 4 5 6 7 8 3 9 4 5 6 7 FREQUENCY (GHz) FREQUENCY (GHz) Insertion Loss vs. Temperature, Vfctl = Vbwctl = 7V Return Loss vs. Temperature, Vfctl = Vbwctl = 7V 0 0 -5 -4 -6 RETURN LOSS (dB) INSERTION LOSS (dB) -2 +25C +85C -40C -8 -10 -12 -14 -16 S11 -10 S22 -15 -20 +25C +85C -40C -25 -18 -20 -30 3 4 5 6 7 FREQUENCY (GHz) 8 9 3 4 5 6 7 8 9 FREQUENCY (GHz) For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] 3-2 HMC892LP5E v00.0910 FILTER - TUNABLE, BAND PASS SMT 4.0 - 7.7 GHz 3 Broadband Return Loss vs. Vbwctl, Vfctl = 7V Broadband Insertion Loss vs. Vbwctl, Vfctl = 7V 0 Vbwctl=4V Vbwctl=7V Vbwctl=10V -20 -5 RETURN LOSS (dB) INSERTION LOSS (dB) -10 -30 -40 -50 -60 Vbwctl=4V -10 -15 -80 -25 Vbwctl=7V -35 0 5 10 15 20 25 30 0 5 10 FREQUENCY (GHz) 15 20 Insertion Loss vs. Vbwctl, Vfctl = 7V 30 Return Loss vs. Vbwctl, Vfctl = 7V 0 0 -2 Vbwctl=4V Vbwctl=7V Vbwctl=10V -5 RETURN LOSS (dB) -4 -6 -8 -10 -12 -14 Vbwctl=4V -10 Vbwctl=7V -15 Vbwctl=10V -20 S11 S22 -25 -18 -30 -20 3 4 5 6 7 8 3 9 4 5 6 7 FREQUENCY (GHz) FREQUENCY (GHz) Center Frequency vs. Temperature, Vfctl = Vbwctl Insertion Loss vs. Temperature, Vfctl = Vbwctl 9 8 9 0 -2 8 +25C +85C -40C 7 INSERTION LOSS (dB) CENTER FREQUENCY (GHz) 25 FREQUENCY (GHz) -16 6 5 4 +25C +85C -40C -4 -6 -8 -10 -12 -14 3 -16 0 2 4 6 Vfctl (V) 3-3 S11 S22 Vbwctl=10V -20 -30 -70 INSERTION LOSS (dB) FILTERS - TUNABLE - SMT 0 8 10 12 14 0 2 4 6 8 10 12 14 Vfctl (V) For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] HMC892LP5E v00.0910 FILTER - TUNABLE, BAND PASS SMT 4.0 - 7.7 GHz Maximum Return Loss in a 2 dB Bandwidth vs. Temperature, Vfctl = Vbwctl 3 dB Bandwidth vs. Temperature, Vfctl = Vbwctl +25C +85C -40C +25C +85C -40C -2 RETURN LOSS (dB) BANDWIDTH (%) 11 10 9 8 -4 -6 -8 -10 7 -12 6 0 2 4 6 8 10 12 0 14 2 4 6 8 10 12 14 12 14 Vfctl (V) Vfctl (V) Low Side Rejection Ratio vs. Temperature, Vfctl = Vbwctl [1] High Side Rejection Ratio vs. Temperature, Vfctl = Vbwctl [1] 1 F20dB To Fcenter RATIO 1.3 +25C +85C -40C 0.95 0.9 0.85 +25C +85C -40C 1.25 FILTERS - TUNABLE - SMT 0 12 F20dB TO Fcenter RATIO 3 1.2 1.15 1.1 1.05 0.8 1 0 2 4 6 8 10 12 14 0 Vfctl (V) 4 6 8 10 Vfctl (V) Tuning Sensitivity vs. Temperature, Vfctl = Vbwctl Group Delay 600 2.5 500 0V 2 GROUP DELAY (ns) SENSITIVITY (MHz/V) 2 400 300 +25C +85C -40C 200 7V 1.5 14V 1 0.5 100 0 0 2 4 6 Vfctl (V) 8 10 12 14 0 2 3 4 5 6 7 FREQUENCY (GHz) 8 9 10 [1] Rejection ratio is defined as the ratio of the frequency at which the relative insertion loss is 20 dB to ƒcenter For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] 3-4 HMC892LP5E v00.0910 FILTER - TUNABLE, BAND PASS SMT 4.0 - 7.7 GHz 3 3 dB Bandwidth vs. Bandwidth Control Insertion Loss vs. Bandwidth Control 0 Vbwctl=Vfctl Vbwctl=Vfctl+3V Vbwctl=Vfctl-3V 14 INSERTION LOSS (dB) BANDWIDTH (%) 16 12 10 8 6 -5 -10 Vbwctl=Vfctl Vbwctl=Vfctl+3V Vbwctl=Vfctl-3V -15 4 2 -20 0 2 4 6 8 10 12 14 0 2 4 6 Vfctl (V) 0.95 1.25 F20dB TO Fcenter RATIO 1.3 0.9 0.85 0.8 Vbwctl=Vfctl Vbwctl=Vfctl +3V Vbwctl=Vfctl -3V 12 14 Vbwctl=Vfctl Vbwctl=Vfctl+3V Vbwctl=Vfctl-3V 1.2 1.15 1.1 1.05 0.7 1 0 2 4 6 8 10 12 14 0 2 4 6 Vfctl (V) 8 10 12 14 Vfctl (V) Maximum Return Loss in a 2 dB Bandwidth vs. Bandwidth Control Input IP3 vs. Power Input Vfctl = Vbwctl 35 0 Vbwctl=Vfctl Vbwctl=Vfctl+3V Vbwctl=Vfctl-3V -2 30 -4 IP3 (dBm) RETURN LOSS (dB) 10 High Side Rejection Ratio vs. Bandwidth Control [1] 1 0.75 8 Vfctl (V) Low Side Rejection Ratio vs. Bandwidth Control [1] F20dB TO Fcenter RATIO FILTERS - TUNABLE - SMT 18 -6 25 20 Pin = 0 Pin = 5 Pin = 10 Pin = 15 Pin = 20 -8 15 -10 10 -12 0 2 4 6 Vfctl (V) 8 10 12 14 3.5 4.5 5.5 6.5 7.5 8.5 FREQUENCY (GHz) [1] Rejection ratio is defined as the ratio of the frequency at which the relative insertion loss is 20 dB to ƒcenter 3-5 For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] HMC892LP5E v00.0910 FILTER - TUNABLE, BAND PASS SMT 4.0 - 7.7 GHz RESIDUAL PHASE NOISE (dBc/Hz) -120 0.5V 5.8V 13.0V -130 3 Absolute Maximum Ratings -140 Frequency Control Voltage (Vfctl) -0.5 to +15V Bandwidth Control Voltage (Vbwctl) -0.5 to +15V RF Power Input 26 dBm Storage Temperature -65 to +150 °C ESD Rating (HBM) Class 1B -150 ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS -160 -170 1.0e+2 1.0e+3 1.0e+4 1.0e+5 1.0e+6 Reliability Information 1.0e+7 OFFSET FREQUENCY (Hz) Junction Temperature to Maintain 1 Million Hour MTTF 150 °C Nominal Junction Temperature (T= 85 °C and Pin = 10 dBm) 90 °C Operating Temperature -40 to +85 °C Outline Drawing FILTERS - TUNABLE - SMT Residual Phase Noise Vfctl = Vbwctl NOTES: 1. LEADFRAME MATERIAL: COPPER ALLOY 2. DIMENSIONS ARE IN INCHES [MILLIMETERS] 3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE. 4. Pin BURR LENGTH SHALL BE 0.15mm MAXIMUM. Pin BURR HEIGHT SHALL BE 0.05mm MAXIMUM. 5. PACKAGE WARP SHALL NOT EXCEED 0.05mm. 6. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. 7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED LAND PATTERN. Package Information Part Number Package Body Material Lead Finish HMC892LP5E RoHS-compliant Low Stress Injection Molded Plastic 100% matte Sn MSL Rating MSL1 [2] Package Marking [1] H892 XXXX [1] 4-Digit lot number XXXX [2] Max peak reflow temperature of 260 °C For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] 3-6 HMC892LP5E v00.0910 FILTER - TUNABLE, BAND PASS SMT 4.0 - 7.7 GHz FILTERS - TUNABLE - SMT 3 Pin Descriptions Pin Number Function Description 1 - 4, 7 - 11, 13 15 - 18, 21 - 32 N/C The pins are not connected internally; however, all data shown herein was measured with these pins connected to RF/DC ground externally. 5, 20 GND These pins and exposed paddle must be connected to RF/DC ground. 6 RFIN This pin is DC coupled and matched to 50 Ohms. External voltage must not be applied to this pin. 12 Vfctl Center frequency control voltage. 14 Vbwctl Bandwidth control voltage. 19 RFOUT This pin is DC coupled and matched to 50 Ohms. External voltage must not be applied to this pin. Interface Schematic Application Circuit 3-7 For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] HMC892LP5E v00.0910 FILTER - TUNABLE, BAND PASS SMT 4.0 - 7.7 GHz 3 FILTERS - TUNABLE - SMT Evaluation PCB List of Materials for Evaluation PCB 128531 [1] Item Description J1, J2 SMA - SRI J3, J4 SMA - Johnson C1, C2 100 pF Capacitor, 0402 Pkg. U1 HMC892LP5E Filter PCB [2] 127338 Evaluation PCB [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Arlon 25FR or Rogers 25FR The circuit board used in the application should use RF circuit design techniques. Signal lines should have 50 Ohms impedance while the package ground leads and exposed paddle should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request. For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] 3-8