HOLTIC HI

HI-5110
CAN Controller with
Integrated Transceiver
September 2010
GENERAL DESCRIPTION
FEATURES
The HI-5110 is a standalone Controller Area Network
(CAN) controller with built in transceiver. The device
provides a complete, integrated, cost-effective solution for
applications implementing the CAN 2.0B specification and
can be configured to implement the Data Link and Physical
Layer interface of the CANopen and DeviceNet standards.
The HI-5110 is capable of transmitting and receiving
standard data frames, extended data frames and remote
frames. The internal transceiver allows direct connection
to the CAN bus without using external components and
coupled with the host Serial Peripheral Interface (SPI),
results in minimal board space.
The HI-5110 provides the optimum solution for
applications where minimum host (MCU) overhead is
required, filtering unwanted messages using a maskable
identifier filter and storing up to 8 messages in the receive
FIFO. Filtering on the first two data bytes is also
supported. A flexible interrupt scheme allows real time
servicing of the FIFO by the host, if required.
Transmissions are handled using an 8 message transmit
FIFO. A Transmit Enable pin can be used by the host to
initiate a transmission. The device also provides monitor
or listen-only mode, low power sleep mode, loopback
mode for self-test and a re-transmission disable capability
(necessary to implement TTCAN protocol).
The HI-5111 is a digital only version of the HI-5110 (no
transceiver). This version provides a “protocol only”
solution for customers who wish to implement the Data
Link layer and use an external transceiver. It may be used
in situations where the customer requires galvanic
isolation between the bus and digital protocol logic. The HI5112 provides an option of a CLKOUT pin instead of a
SPLIT pin, which may be used as the main system clock or
as a clock input for other devices in the system. Finally, the
HI-5113 provides all options (both CLKOUT and SPLIT
pins) in a very compact QFN-44 package.
The HI-5110 family is available in industrial temperature
o
o
range, -40 C to + 85 C, with a “RoHS compliant” lead-free
option.
· Implements CAN version 2.0B with programmable bit
rate up to 1Mbit/sec. ISO 11898-5 compliant.
· Configurable
to support CANopen and DeviceNet
Data Link and Physical layers.
· Serial Peripheral Interface (SPI) (20MHz).
· Standard, Extended and Remote frames supported.
· 8 maskable identifier filters.
· Filtering on ID and first two data bytes for both
Standard and Extended Identifiers.
· Loopback mode for self-test.
· Monitor (Listen-only) and Low
Power Sleep Modes
with automatic wake-up possible.
· 8-message Transmit and Receive FIFOs.
· Power-On-Reset.
· Transmit history FIFO.
· Internal 16-bit free running counter for time tagging of
transmitted or received messages.
· Permanent dominant timeout protection.
· Short Circuit Protection of -58V to + 58V on CAN_H,
CAN_L and SPLIT pins (ISO 11898-5).
· Re-transmission disable capability.
· Transmit Enable pin.
· Industrial temperature range, -40 C to + 85 C.
o
o
PIN CONFIGURATION (Top View)
VLOGIC 1
18 INT
OSCOUT 2
17 MR
OSCIN 3
16 CS
GP1 4
GP2 5
15 SO
5110PSI
14 SI
TXEN 6
13 SCK
SPLIT 7
12 STAT
GND 8
CANL 9
11
VDD
10 CANH
18-Pin Plastic SOIC - WB Package
(DS5110 Rev. New)
HOLT INTEGRATED CIRCUITS
www.holtic.com
09/10
HI-5110
BLOCK DIAGRAM
VLOGIC
CS
SPI BUS SCK
SI
SO
BIT
TIMING
REGISTERS
SPI DECODE/
ENCODE
VDD
GND
TRANSMIT
LOGIC & FIFO
TXEN
HISTORY
FIFO
TRANSCEIVER
GP2
GP1
STAT
CANH
INTERRUPTS
AND
STATUS
ERROR
STATUS
& CONTROL
CANL
INT
RECEIVE
LOGIC & FIFO
SPLIT
(see ordering
information)
FILTERS
OSCIN
TIME-TAG
COUNTER
OSCILLATOR
OSCOUT
MR
CLOCK DIV
OUT
CLKOUT
(see ordering
information)
HI-3110
Figure 1. HI-5110 Block Diagram
PRIMARY FUNCTIONS OF HI-5110 LOGIC BLOCKS
SPI PROTOCOL BLOCK
8 message FIFO with optional filters
Handles data transfers between the host and the chip Forwards message data and optional time stamp to the host
REGISTERS BLOCK
Stores configuration data
ERROR BLOCK
Detects and records errors for protocol management
BIT TIMING BLOCK
Sets the data strobe and bit period
STATUS AND INTERRUPT
Provides hardware and software options for managing
communications
TRANSMIT BLOCK
Manages transmission protocol
8 message FIFO
Confirmation and time stamp of each message sent
is available in the History FIFO
RECEIVER BLOCK
Manages reception protocol
OSCILLATOR
Configuration chooses either the crystal oscillator or and
external clock
TRANSCEIVER
Analog interface connects directly to the CAN bus
HOLT INTEGRATED CIRCUITS
2
HI-5110
PIN DESCRIPTIONS
SIGNAL
FUNCTION
SCK
CS
SI
SO
INT
STAT
TXEN
INPUT
INPUT
INPUT
OUTPUT
OUTPUT
OUTPUT
INPUT
OSCIN
INPUT
OSCOUT
OUTPUT
GP1
OUTPUT
GP2
OUTPUT
CLKOUT
SPLIT
OUTPUT
OUTPUT
CANH
CANL
MR
BUS I/O
BUS I/O
INPUT
VDD
VLOGIC
POWER
POWER
GND
POWER
DESCRIPTION
SPI Clock. Data is shifted into or out of the SPI interface using SCK
Chip Select. Data is shifted into SI and out of SO when CS is low.
SPI interface serial data input
SPI interface serial data output
Active high. Programmable interrupt output
Active high. Programmable status output.
Active high. Transmit Enable pin. When the TXEN pin is asserted, any message
in the Transmit FIFO will be automatically loaded to the Transmit buffer and sent
if the bus is available. This pin is logically ORed with the TXEN and TX1M bits
in the CTRL1 register. When the TXEN pin is reset, messages loaded to the
FIFO will not be sent until TXEN or TX1M bits are set in the CTRL1 register.
Crystal input. A parallel resonant crystal can be connected between OSCIN and
OSCOUT. If an external clock is used, it should be connected to the OSCIN pin
and the OSCOUT pin should be left floating. The internal oscillator should be
shut off by setting the OSCOFF bit in the CTRL1 register.
Crystal output. If an external clock is used, this pin should be left floating and
disabled by setting the OSCOFF bit in the CTRL1 register.
General purpose pin 1, which can be programmed to reflect the values of
interrupt and status flag bits.
General purpose pin 2, which can be programmed to reflect the values of
interrupt and status flag bits.
Clock output pin with programmable frequency divider.
VDD/2 output bias (Powered off in Sleep Mode and when the common mode
bias is greater than 25V).
CAN bus line high.
CAN bus line low.
Active High. Device Master Reset input pin. Asserting this pin resets all registers
and memory buffers to their default state at start-up.
5V supply voltage input.
3.3V supply voltage input. This supply is used to drive the host digital logic I/O.
It can either be connected directly to VDD (+5V) or a +3.3V supply.
Supply voltage ground.
HOLT INTEGRATED CIRCUITS
3
INTERNAL PULL UP / DOWN
50K ohm pull-down
50K ohm pull-up
50K ohm pull-down
100K ohm pull-down
50K ohm pull-down
HI-5110
FUNCTIONAL OVERVIEW
The HI-5110 is the first single chip product to integrate both
the CAN (Controller Area Network) protocol and analog
interface transceiver on a single IC. The protocol conforms
to CAN version 2.0B and is compliant with ISO 118981:2003(E) specification. The transceiver is compliant with
ISO 11898-5 specification.
Configuration options include an internal Loopback mode
that does not disturb the bus, a Monitor only mode, and a
Sleep mode that includes an option to either wake up
automatically when data is present on the bus, or by host
command. The following sections describe some of the key
features.
SPI and REGISTERS
To minimize the footprint, a 20 MHz standard four wire SPI
(Serial Peripheral Interface) is provided to manage the flow
of data between the host microcontroller and the HI-5110.
Complete messages are loaded and retrieved with single
SPI op codes. On the receive side, SPI op code options may
be used to retrieve the whole message or just the data. An
option to include a time tag or no time tag may also be
specified. On the transmit side, each message can be
assigned an identifier which allows monitoring of the
Transmit History FIFO to confirm the successful completion
of a transmission along with the time stamp. In addition the
transmitter logic automatically assembles the message
frame based on the data presented.
BIT TIMING
Bit timing is controlled with standard CAN options. These
include control of the Resychronization Jump Width (SJW),
Prop delay Phase Seg 1 (TSeg1), Phase Seg 2 (TSeg2), the
number of samples, and the derivation of Tq from the system
clock using a prescaler. The maximum bit rate is 1 MBit/sec.
Upon reset, the chip automatically enters Initialization mode
which allows programming of the Bit Timing before entering
Normal mode.
TRANSMITTER
The transmitter state machine automatically handles all
CAN 2.0B protocol requirements. Messages for
transmission are first loaded into a FIFO and transmission
may start upon availability of data in the FIFO. Assertion of
the TXEN pin or configuration bits in Control Register 1 allow
either continuous transmission until the FIFO is empty or
only one message from the FIFO at a time. One shot (no
retry) transmission may also be enabled by setting the OSM
bit. SPI op codes are provided to clear the Transmit FIFO
and to abort transmission.
RECEIVER
The receiver state machine automatically handles all CAN
2.0B protocol requirements. The receiver supports eight
sets of filters and masks and each allows filtering of a full
CAN ID (extended or not) and two bytes of data. Even when
filtering is enabled, message data is always accessible as
received via the Temporary Receive Buffer, and retrievable
by SPI op codes 0x42 and 0x44.
If the Filter/Mask option is set (FILTON bit in Control Register
1), only messages that match one of the 8 stored data
patterns are passed into the FIFO. Note that the Mask option
allows certain bits of the programmed filter bits to be “don't
care.” If the Filter/Mask option is not set, then all valid
messages are passed to the FIFO. When the FIFO is full (8
completed messages received), the next received message
is not loaded in the FIFO.
ERROR CONTROL
Errors are detected per ISO 11898-1:2003(E) and
detections are counted and used by the protocol state
machines. Active, Passive, and Bus Off conditions are
managed per the CAN standard. A configuration bit is
provided to allow automatic recovery from Bus Off.
STATUS and INTERRUPTS
The Message Status Register, MESSTAT, provides
information about the current state of the receiver and
transmitter operation. In addition, the Interrupt Flag
Register, INTF, monitors 8 operational conditions, any or all
of which may be directed to the INT pin by enabling bits in the
Interrupt Enable Register, INTE. Similarly, the Status Flag
Register, STATF, bits reflect the status of selected FIFO and
Error properties. Any or all of these conditions may be
directed to the STAT pin by setting the enable bits in the
Status Flag Enable Register, STATFE.
To provide additional hardwired flag options, the GP1 and
GP2 pins may also be programmed to reflect any of the
Interrupt or Status Flag bits.
OSCILLATOR and TIME TAG
A configuration bit allows a choice for the source of the
system clock. Either the on-board crystal oscillator may be
selected or an external clock may be provided at the OSCIN
pin.
On product versions with the CLKOUT pin, a programmable
division of the system clock is provided. The clock source for
the 16 bit Time Tag Counter is derived from a separate
programmable division of the system clock. SPI op codes
provide for reading and resetting the Time Tag Counter.
HOLT INTEGRATED CIRCUITS
4
HI-5110
TRANSCEIVER
The HI-5110 contains an integrated transceiver operating
from 5V and the line driver is capable of maintaining a
detectable signal for bus lengths well in excess of
recommended CAN 2.0B standards. The digital logic and IO
can be powered from 3.3V or 5V.
PROTECTION FEATURES
The BUS and SPLIT pins are protected against ESD to over
4KV (HBM) and from shorts between -58V to +58V
continuous, as specified in ISO 11898-5.
In addition, a Permanent Dominant Timeout protection is
implemented by means of an independent counter
monitoring the dominant transmission state and
automatically shutting off the transmission if it exceeds
typically 2ms.
required in the usual way. While in this mode, any bus
activity is ignored. Loopback is activated by programming
the MODE<2:0> bits to <001> in the CTRL0 register.
MONITOR MODE
Monitor mode (also known as listen-only or silent mode)
allows the HI-5110 to monitor all bus activity without
disturbing the bus. No messages or dominant bits (such as
ACK or active error frame bits) are transmitted to the bus
while in this mode. Also, the error counters are reset and
deactivated. Messages from the bus are received in the
same way as Normal Mode and messages that are not
acknowledged by another node on the bus are ignored i.e.
any frame containing an error will be ignored. Acceptance
filters can be set up to reject or accept specific messages
into the FIFO and all interrupt flags are set as required in the
usual way. Monitor mode is activated by programming the
MODE<2:0> bits to <010> in the CTRL0 register.
SLEEP MODE
MODES OF OPERATION
The HI-5110 supports five modes of operation, namely,
Initialization Mode, Normal Mode, Loopback Mode, Monitor
Mode and Sleep Mode.
INITIALIZATION MODE
Initialization mode is used to configure the device before
normal operation. Bit timing registers and acceptance
filters and masks can only be modified in this mode.
Initialization mode is the default mode following RESET and
can also be activated by programming the MODE<2:0> bits
to <1xx> in the CTRL0 register. Switching to Initialization
mode resets the receiver and transmitter. During
initialization mode, the error counters are held reset.
NORMAL MODE
Normal mode is the standard operating mode of the HI-5110.
In this mode, the HI-5110 can transmit, receive and
acknowledge messages from the CAN bus, handling all
aspects of the CAN protocol. Normal mode is activated by
programming the MODE<2:0> bits to <000> in the CTRL0
register.
LOOPBACK MODE
The HI-5110 can be placed in a low power sleep mode if
there is no bus activity and the transmit FIFO is empty. In
this mode, the internal oscillator and all analog circuitry
(transceiver) are off, drawing typically less than 20mA. Note
that the SPI bus is active during sleep mode, so it is possible
for the host to communicate with the HI-5110 while it is
asleep (e.g. load transmit FIFOs). Sleep mode is exited by
selecting an alternative mode of operation, or automatic
wake up following bus activity can be enabled by setting the
WAKEUP bit in the CTRL0 register - in this case a low power
receiver monitors the bus for a detectable dominant bit. The
device will wake up in Monitor Mode. Note that it will take a
finite time for the oscillator and analog circuitry to come back
on line. Since the internal oscillator takes a finite time to
wake up, the message which caused the wake-up may not
be stored.
Sleep mode is activated by programming the MODE<2:0>
bits to <011> in the CTRL0 register. However, the actual
mode change will only occur whenever the CAN bus is quiet.
If the chip is transmitting, the mode change is delayed until
the transmission is complete. If there is bus activity, the
mode change is delayed until the receiver protocol control
detects an inter-message gap.
CAN PROTOCOL OVERVIEW
Loopback mode is used for self-test. The transceiver digital
input is fed back to the receiver without being transmitted to
the bus. Messages are transmitted from the transmit FIFO
in the usual way and received by the receive FIFO as if they
were received from a remote node on the bus.
Acceptance filters can be set up to accept or reject specific
messages into the FIFO and all interrupt flags are set as
The HI-5110 supports Standard, Extended and Remote
Frames, as defined in the CAN specification IS0 118981:2003(E) (also known as CAN 2.0B).
BIT ENCODING
CAN frames are encoded according to the Non-Return-ToZero (NRZ) method with bit stuffing. NRZ means that the
HOLT INTEGRATED CIRCUITS
5
HI-5110
generated bit level is constant during the total bit time and
consecutive bits do not return to a neutral or rest condition.
This means that a bit stream of “1s” or “0”s appears
continuous on the bus. A logic “0” is called a dominant bit
and a logic “1” is called a recessive bit.
Bit stuffing is used to ensure frequent enough transitions
occur to achieve synchronization. Every time a transmitter
detects five consecutive bits of the same polarity in the bit
stream to be transmitted, it inserts a bit of opposite polarity
into the actual transmitted bit stream.
This bit stuffing rule applies to the Start-of-Frame field,
arbitration field, control field, data field and CRC sequence.
The CRC delimiter, ACK field and End-Of-Frame fields are of
fixed form and not stuffed (see below for definition of these
fields). Furthermore, Error frames and Overload frames are
also of fixed form and not stuffed.
An example of how the bits in a stuffed bit stream might look
is shown below.
00101011111O0000I1100000I11000
0 = dominant bit, O = dominant stuffed bit.
1 = recessive bit, I = recessive stuffed bit.
MESSAGE FRAMES
STANDARD DATA FRAME
The standard data frame is shown in figure 2. The frame
starts with a Start-of-Frame (SOF) bit. This is a dominant bit
that identifies the start of the data frame on the bus.
The SOF is followed by the 12-bit arbitration field. The
arbitration field consists of an 11-bit identifer, ID28 - ID18,
and the Remote Transmission Request (RTR) bit. The RTR
bit is used to distinguish between a data frame (RTR bit
dominant, logic 0) and a remote frame (RTR bit recessive,
logic 1).
Following the arbitration field is the 6-bit control field. The
first bit of the control field is the Identifier Extension flag bit
(IDE). This is used to distinguish between standard and
extended identifiers and must be dominant (logic 0) for
standard data frames. The next bit, r0, is specified by the
CAN protocol as a reserved bit for future expansion. This bit
must be transmitted dominant, but receivers must be
capable of receiving either a dominant or recessive bit. The
final 4 bits of the control field make up the data length code
(DLC). The binary value of this 4-bit field specifies the
number of data bytes in the data payload (0 - 8 bytes). Note:
All binary combinations greater than or equal to <1 0 0 0>
specify 8 bytes of data.
After the control field is the data field, which contains a data
payload equal to the number of bytes specified by the DLC
(see note above).
The data field is followed by the 16-bit Cyclic Redundancy
Check (CRC) field. This is used to check transmission
errors by computing a 15-bit CRC sequence from the
previous bit stream (SOF, arbitration field, control field and
data field, excluding stuff bits). The last bit in the CRC field is
the CRC delimiter bit (always recessive).
After the CRC field is the Acknowledge Field (ACK Field).
The first bit is the ACK Slot bit. A transmitting node sends a
recessive bit (logic 1) during the ACK slot. Any node which
receives the message error-free acknowledges the
reception by placing a dominant bit (logic 0) in the ACK slot,
over-writing the recessive bit of the transmitter. The final bit
in the ACK field is a recessive ACK delimiter bit. Therefore,
the dominant ACK slot bit is surrounded on each side by a
recessive bit.
Each data frame is delimited by an End-Of-Frame field
(EOF). The EOF consists of seven recessive bits.
Following the EOF, there is a gap to the next frame called the
Interframe Space (IFS) . The IFS consists of two bit fields,
Intermission and Bus-Idle. The Intermission consists of
three recessive bits, however the following notes apply:
a) detection of a dominant bit on the bus at the third slot is
interpreted as a SOF,
b) detection of a dominant bit in either the first or second
slots results in generation of an overload frame (see below).
The bus idle period is of arbitrary length and consists of
recessive bits. A dominant bit detected during this period is
interpreted as a SOF.
EXTENDED DATA FRAME
The extended data frame is shown in figure 3. In this frame
format, SOF is followed by a 32-bit arbitration field consisting
of a 29-bit identifier, ID28 - ID0. The first 11 most significant
bits of the ID are know as the base identifier. This is followed
by the Substitute Remote Request (SRR) bit, which is
defined as recessive. Following the SRR bit is the IDE bit,
which is defined as recessive for extended data frames.
Note that the SRR bit is in the same slot as the RTR bit of the
standard frame and the IDE bits are also in corresponding
slots. This means if standard and extended identifier data
frames with identical base identifiers are transmitted
simultaneously, the standard identifier data frame will win
arbitration (see Bitwise Arbitration section below).
The SRR and IDE bits are followed by the remaining 18 bits
of the identifier (extended ID) and the last bit of the
arbitration field is the RTR bit. The RTR bit has the same
function as in the standard frame format.
Following the arbitration field is the 6-bit control field. The
first two bits, r1 and r0, are specified by the CAN protocol as
reserved bits for future expansion. Both these bits must be
transmitted dominant, but receivers must be able to receive
all combinations of dominant or recessive bits. The final 4
bits of the control field is the data length code (DLC). The
HOLT INTEGRATED CIRCUITS
6
HI-5110
binary value of this 4-bit field specifies the number of data
bytes in the data payload (0 - 8 bytes). Note: All binary
combinations greater than or equal to <1 0 0 0> specify 8
bytes of data.
The remaining fields of the extended data frame (Data field,
CRC field, acknowledge field, EOF field and IFS field) are
constructed in the same way as the standard frame format.
REMOTE FRAME
The remote frame is shown in figure 4. The function of
remote frames is to allow a receiver which periodically
receives certain types of data to request that data from the
transmitting source. The identifier of the remote frame must
be identical to the identifier of the requested transmitting
node’s data frame and the data length code (DLC) should be
equal to the DLC of the requested data. Simultaneous
transmission of remote frames with the same identifier
and different DLCs will lead to unresolvable collisions
on the bus.
The format of a remote frame is identical to the format of the
corresponding data frame except the remote frame has no
data payload. Remote frames and data frames are
distinguished by a recessive RTR bit in the remote frame.
This means if a receiver sends a remote frame and the
sending node transmits at the same time, the sending node
(with a dominant RTR bit) will win arbitration and the
requesting node will receive the desired data immediately.
ERROR FRAME
The error frame is shown in figure 5. Any node detecting an
error generates an error frame. The error frame consists of
two fields, the error flag field and the error delimiter. The
type of error flag field depends on the error status of the
node, error-active or error-passive (see below). An erroractive node generates an active error flag and an errorpassive node generates a passive error flag.
Active Error Flag: An active error flag consists of 6
consecutive dominant bits. This condition violates the rule
of bit-stuffing and causes all other nodes on the bus to
generate error flags, known as echo error flags. Therefore,
the error flag field will consist of the superposition of different
error flags sent by individual nodes, resulting in a minimum
of 6 and maximum of 12 consecutive dominant bits. The
error flag field is followed by the error delimiter, consisting of
8 recessive bits.
it must wait for 6 consecutive bits of equal polarity before
completing the error flag. If the passive error flag is
generated by a transmitter, the bit stuffing rule is violated and
it will cause other nodes to generate error flags. Two
exceptions to this rule are
a) the passive error flag starts during arbitration and another
node prevails and begins transmitting, and
b) the error flag starts less than 6 bits before the end of the
CRC sequence and the last bits of the CRC sequence all
happen to be recessive.
OVERLOAD FRAME
The overload frame is shown in figure 6. It has the same
format as the active error frame, consisting of an overload
flag field and an overload delimiter. The overload flag
consists of 6 consecutive dominant bits. This condition
violates the rule of bit-stuffing and causes all other nodes on
the bus to generate echo flags, similar to the active error flag
echos. Therefore, the overload flag field will consist of the
superposition of different overload flags sent by individual
nodes, resulting in a minimum of 6 and maximum of 12
consecutive dominant bits. The overload flag is followed by
the overload delimiter, consisting of 8 recessive bits.
An overload frame, unlike an error frame, can only be
generated during the interframe space. There are two types
of overload frame:
1) Reactive Overload Frame, resulting from
a) detection of a dominant bit during the first or second bit of
intermission,
b) detection of a dominant bit at the last (seventh) bit of EOF
in received frames, or
c) detection of a dominant bit at the last (eighth) bit of an error
delimiter or overload delimiter.
The reactive overload frame is started one bit after detecting
any of the above dominant bit conditions.
2) Requested Overload Frame. A node which is unable to
begin reception of the next message due to internal
conditions may request a delay by transmitting a maximum
of two consecutive overload frames. The requested
overload frame must be started at the first bit of an expected
intermission.
Note: The HI-5110 will never initiate an overload frame
unless reacting to one of the conditions in case 1) above.
Passive Error Flag: A passive error flag consists of 6
recessive bits. This is followed by the 8 recessive bits of the
error delimiter. Therefore, an error frame sent by an errorpassive node consists of 14 consecutive recessive bits.
Since this will not disturb the bus, a transmitting node will
continue to transmit unless it detects the error itself, or
another error-active node detects the error.
Notes: If the passive error flag is generated by a receiver, it
cannot prevail over any other activity on the bus. Therefore,
HOLT INTEGRATED CIRCUITS
7
HI-5110
KEY.
1 1 1 1 1 1 1 1 1 1 1
1
IFS
EOF
7
15
SOF
IDxx
RTR
IDE
r0
DLCx
CRC Del
ACK Slot bit
ACK Del
EOF
IFS
8
......
Data Field
8n (0 £ n £ 8)
8
16
CRC Del
ACK Slot bit
ACK Del
CRC Field
Intermission
Data
Length
Code
4
Base Identifier
0 0
0
11
SOF
ID28
Control Field
ID23
Arbitration Field
ID18
RTR
IDE
r0
DLC3
6
Reserved bit
12
DLC0
Data Frame (44 + 8n bits)
Bus Idle or SOF
.....
Standard Data Frame
Figure 2. Standard Frame Format.
HOLT INTEGRATED CIRCUITS
8
Start-Of-Frame
Identifier bit xx
Remote Transmission Request bit
Identifier Extension Flag
Reserved bit 0
Data Length Code bit x
Cyclic Redundancy Check Delimiter
Acknowledge Slot bit
Acknowledge Delimiter
End-Of-Frame
Interframe space
HI-5110
1 1 1 1 1 1 1 1 1 1 1
1
IFS
7
Intermission
EOF
Bus Idle or SOF
........
Extended Data Frame
CRC Del
ACK Slot bit
ACK Del
15
SOF
IDxx
SRR
IDE
RTR
r1
r0
DLCx
CRC Del
ACK Slot bit
ACK Del
EOF
IFS
....
8
8n (0 £ n £ 8)
Data Field
Data
Length
Code
4
0
Extended Identifier
1 1
Base Identifier
0
18
11
ID18
SRR
IDE
ID17
ID23
Control Field
ID9
6
ID0
RTR
r1
r0
DLC3
32
Reserved bits
Arbitration Field
DLC0
SOF
ID28
Data Frame (64 + 8n bits)
8
16
CRC Field
KEY.
Figure 3. Extended Frame Format.
HOLT INTEGRATED CIRCUITS
9
Start-Of-Frame
Identifier bit xx
Substitute Remote Request bit
Identifier Extension Flag
Remote Transmission Request bit
Reserved bit 1
Reserved bit 0
Data Length Code bit x
Cyclic Redundancy Check Delimiter
Acknowledge Slot bit
Acknowledge Delimiter
End-Of-Frame
Interframe space
SOF
0
Base Identifier
ID23
11
ID18
SRR
IDE
ID17
1 1
18
HOLT INTEGRATED CIRCUITS
10
Data
Length
Code
No Data Field. See NOTE regarding Data Length Code.
Extended Identifier
1
4
DLC0
Control Field
ID0
RTR
r1
r0
DLC3
Reserved bits
Arbitration Field
ID9
6
15
CRC Field
16
.....
IFS
1 1 1 1 1 1 1 1 1 1 1
CRC Del
ACK Slot bit
ACK Del
1
EOF
7
Intermission
32
Bus Idle or SOF
Remote Frame with Extended ID (64 bits)
HI-5110
Remote Frame
Figure 4. Remote Frame Format (Extended Identifier).
ID28
SOF
ID28
0
Base Identifier
ID18
SRR
IDE
ID17
1 1
Extended Identifier
0
Data
Length
Code
4
Control Field
ID9
18
6
32
DLC0
Arbitration Field
ID0
RTR
r1
r0
DLC3
Reserved bits
11
ID23
Data Frame with error detected during data transmission
8
....
Data Field
8n (0 £ n £ 8)
8
Figure 5. Error Frame Format.
HOLT INTEGRATED CIRCUITS
11
8
Error
Delimiter
.... 0 0 1 1 1 1 1 1
Error
Echo
Flag
0 0 0 0 0 0 0 0
Up to 6 bits
6
Active
Error
Flag
Error Flag Field
Error Frame
Intermission
1 1 1 1 1
HI-5110
Error Frame
.... 1
Figure 6. Overload Frame Format
HOLT INTEGRATED CIRCUITS
12
Overload
Echo
Flag
Overload
Flag
Overload
Delimiter
8
.... 0 0 1 1 1 1 1 1
Up to 6 bits
Overload Flag Field
Overload Frame
0 0 0 0 0 0 0 0
Illegal Dominant Bit in IFS
6
IFS
1 1 1 1 1 1 1 0
EOF
7
Data Frame or Remote Frame
Intermission
1 1 1 1 1
HI-5110
Overload Frame
HI-5110
BIT WISE ARBITRATION
The CAN standard resolves data contention on the bus
using a scheme called Carrier Sense Multiple
Access/Collision Detection-Carrier Resolution (CSMA/CDCR).
RTR
ID18
1
Standard ID Arbitration Field
ID28
TXCAN: Node 1
Start-OF-Frame
Carrier Sense: Each node waits for a period without bus
activity (bus idle state) before attempting transmission.
Multiple Access: Every node on the bus has equal access
to the bus for transmitting.
Collision Detection: Collisions occur if two nodes attempt
to transmit at the same time.
Collision Resolution: Collisions are resolved by bitwise
arbitration.
Highest priority messages (lowest binary
identifiers) are sent first without delay and lower-priority
messages are automatically re-transmitted later. A dominant
bit (logic 0) has priority over a recessive bit (logic 1).
Bitwise arbitration works by comparing each node’s
transmitted data bit by bit. All nodes are synchronized by
adjusting individual bit times as a function of bit time quanta
(see section on bit timing). Synchronization takes place on
recessive to dominant edges. A Hard Synchronization at the
start of each frame and subsequent re-synchronizations
during a message frame ensures corresponding bits match
in time during a given transmission cycle. When a node
transmits a recessive bit on the bus, but detects a dominant
bit on it’s receiver, it realizes arbitration is lost and it
immediately ceases transmission and becomes a receiver.
It will then wait for the next bus idle state and attempt to retransmit. Eventually, lower priority messages will gain
access to the bus. Figure 7 shows an example of how this
works for a frame with a standard identifier.
0
TXCAN: Node 2
1
0
TXCAN: Node 3
1
0
CAN Bus differential
signal (not to scale)
Node 2 loses arbitration
Node 3 loses arbitration
Figure 7. Bitwise Arbitration.
HOLT INTEGRATED CIRCUITS
13
HI-5110
BIT TIMING
The CAN protocol supports a broad range of bit rates, from a
few kHz up to 1MHz (Note: the minimum bit rate of the HI5110 is limited to 40kHz by the permanent dominant timeout
protection of the transceiver). Every node on the network
has it’s own clock generator (typically a quartz oscillator),
however the bit rate must obviously be the same for every
node on the bus. Therefore, each CAN node must be
configurable to generate the nominal bit rate as a function of
it’s own oscillator frequency, fOSC. This is done by generating
a time quanta (TQ) clock, whose period tTQ is related to the
oscillator frequency by a Baud Rate Prescaler value, BRP as
follows:
tTQ = 2•BRP/fOSC
(1)
The TQ clock is used to construct the bit time in terms of time
quanta, such that one time quantum, Tq, equals one TQ
clock period, tTQ, as shown in figure 8 below.
The CAN system nominal bit rate (BR) is defined in terms of
the nominal bit time, tb, as
BR = 1/tb
(2)
The CAN standard divides the bit time into four segments,
namely, synchronization segment (Sync Seg), propagation
time segment (Prop Seg), phase buffer segment 1 (Phase
Seg1) and phase buffer segment 2 (Phase Seg2). This is
illustrated in figure 8. The HI-5110 fixes the Sync Seg at
1Tq. Prop Seg and Phase Seg1 are treated as one time
segment, TSeg1, which is programmable from 2Tq to 16Tq.
Phase Seg2 is a second time segment, TSeg2, which is
programmable from 2Tq to 8Tq (Note: Not all combinations
are valid, see below for examples).
Synchronization Segment (Sync Seg)
The Sync Seg is the first segment of the bit time and is used
to synchronize the various nodes on the bus. A bit edge is
expected to occur within the Sync Seg.
Propagation Time Segment (Prog Seg)
The Prog Seg is used to compensate for physical delays on
the bus, which include signal propagation delay time on the
bus and internal node delay times. For two nodes A and B
communicating on the bus, Prog Seg must be greater than
or equal to the sum of both nodes internal delays plus twice
the bus line propagation delay between the two nodes.
Therefore, the nominal bit rate is related to the TQ clock
period by the following relationship
BR = 1/(tTQ x (number of time quanta per bit))
(3)
tOSC
OSC
Baud Rate Prescaler
tTQ
TQ
Clock
Nominal bit time, tb
Tq
Sync
Seg
TSeg1 =
Prop Seg + Phase Seg 1
Sync
TSeg2 =
Phase Seg2 Seg
Sample
Point
Figure 8. CAN Bit Time
HOLT INTEGRATED CIRCUITS
14
TSeg1
TSeg2
HI-5110
Phase Buffer Segment 1 and Phase Buffer
Segment 2 (Phase Seg1 and Phase Seg2)
The phase buffer segments are used to compensate for
phase errors on the bus. Phase Seg1 can be lengthened or
Phase Seg2 can be shortened duringthe re-synchronization
bit period automatically by the HI-5110 so that the bit time
can be adjusted to account for phase errors. The upper limit
by which the lengthening ( or shortening) can occur is set by
the re-synchronization jump width (SJW), explained in
more detail below.
Sample Point
The sample point is the point in the bit time at which the bit
logic level is interpreted. It is located at the end of Phase
Seg1. The HI-5110 also allows three sample points to be
taken. In this case, two other sample points are taken prior
to the end of Phase Seg1 (at one-half TQ intervals) and the
value of the bit is determined by a majority decision. Three
sample points are typically only used at low bit rates.
The time required for the logic to determine the bit level of a
sampled bit is known as the information processing time
(IPT). According to the standard, IPT can be up to 2Tq.
Since Phase Seg2 occurs after the sample point, Phase
Seg2 must be greater than or equal to the worst case IPT
(2Tq).
Re-synchronization results in the shortening or
lengthening of the bit time such that the position of the
sample point is shifted with respect to the edge causing the
re-synchronization. For e > 0, Phase Seg 1 is lengthened by
the magnitude of the phase error, up to a maximum of SJW.
For e < 0, Phase Seg 2 is shortened by the magnitude of the
phase error, up to a maximum of SJW.
Examples
1) CAN bit rate (BR) = 250kHz
Assume sample point (at end of TSeg1) will occur > 80% of
bit time. Hence, for Sync Seg = 1Tq, TSeg1 = 15Tq and
TSeg2 = 2Tq. Therefore, total bit time will be 18Tq. Chose
SJW = 1Tq.
For 250kHz, the bit time needs to be 1/250kHz = 4μs.
Hence, 1Tq = 0.22μs. Using equation (1), if BRP = 2 => fosc
= 18MHz.
2) CAN bit rate (BR) = 1MHz
Assume sample point (at end of TSeg1) will occur > 80% of
bit time. For Sync Seg = 1Tq, then TSeg1 = 15Tq and
TSeg2 = 2Tq. Therefore, total bit time will be 18Tq. Chose
SJW = 1Tq.
For 1MHz, the bit time needs to be 1/1MHz = 1μs. Hence,
1Tq = 55.5ns. Using equation (1), if BRP = 1 => fosc =
36MHz.
Phase Errors (e)
If a bit edge occurs within the Sync Seg as expected, there is
no phase error (e = 0). However, if an edge occurs outside
Sync Seg, a phase error is deemed to have occurred. If the
edge occurs after Sync Seg (edge occurs “late”), the phase
error is positive (e > 0), whereas if the edge occurs before
Sync Seg (edge occurs “early”), the phase error is negative
(e < 0).
Synchronization
Synchronization is carried out only on recessive-todominant bit edges and is used to ensure the bit times of all
nodes on the bus are synchronized. This is necessary for
arbitration and message acknowledgment to function
properly. Only one synchronization can occur per bit time.
Hard synchronization forces the bit edge to lie within the
Sync Seg, regardless of the phase error.
Hard
synchronization only occurs on reception of the start of a
frame.
HOLT INTEGRATED CIRCUITS
15
HI-5110
REGISTERS
This section describes the HI-5110 registers. All register bits are active high. Unless otherwise indicated, all registers are reset
in software to the logic zero condition after Master Reset. For all registers, bit 7 is the most significant:
REGISTER
CTRL0
CTRL1
BTR0
BTR1
TEC
REC
MESSTAT
ERR
INTF
INTE
STATF
STATFE
GPINE
TIMERUB
TIMERLB
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R
R
R
R/W
R
R/W
R/W
R
R
DESCRIPTION
Configuration Register 0
Configuration Register 1
Bit Timing Register 0
Bit Timing Register 1
Transmit Error Counter Register
Receive Error Counter Register
Message Status Register
Error Register
Interrupt Flag Register
Interrupt Enable Register
Status Flag Register
Status Flag Enable Register
General Purpose Pins Enable Register
Free-Running Timer Upper Byte Register
Free-Running Timer Lower Byte Register
SPI WRITE
SPI READ
OP-CODE
OP-CODE
0x14
0x16
0x18
0x1A
0x26
0x24
N/A
N/A
N/A
0x1C
N/A
0x1E
0x22
N/A
N/A
0xD2
0xD4
0xD6
0xD8
0xEC
0xEA
0xDA
0xDC
0xDE
OxE4
0xE2
0xE6
0xE8
0xFA*
0xFA*
* Note: Free-running counter registers, TIMERUB:TIMERLB are read with a single SPI Op-code (0xFA) as a 16bit value in two SPI data bytes.
Power-On-Reset
Following power-on, the HI-5110 will automatically perform a Master Reset and return all registers to the default state.
Following reset, the device will default to Initialization Mode to allow programming of Control and Bit Timing Registers (see
following sections).
HOLT INTEGRATED CIRCUITS
16
HI-5110
(Write, SPI Op-code 0x14)
(Read, SPI Op-code 0xD2)
M
M
O
D
E
O 2
D
M E1
O
D
W E0
AK
R EU
ES P
BO ET
R
TT
D
TT IV1
D
IV
0
CONTROL REGISTER 0: CTRL0
7 6
MSB
Bit Name
R/W
7-5 MODE2:0
R/W
5
4
3
2
1
0
LSB
Default Description
1,0,0
Mode select bits <2:0>.
These bits select the mode of operation as follows.
000: Normal Mode.
001: Loopback Mode.
010: Monitor Mode.
011: Sleep Mode.
1xx: Initialization Mode.
Normal CAN operation.
The transceiver digital input is fed back to the receiver without
disturbing the bus. This mode can be used for test purposes,
allowing the HI-5110 to receive its own messages.
The HI-5110 can be set up to monitor bus activity without
transmitting to the bus (no ACK bits or error frames are sent in this
mode). Receive filters can be programmed in Initialization Mode to
buffer selected messages.
The HI-5110 can be placed in a low power sleep mode if there is no
bus activity and the transmit FIFO is empty. Sleep mode is exited
by selecting an alternative mode of operation, or automatic wake
up following bus activity can be enabled by setting the WAKEUP
bit. The device will wake up in Monitor mode.
The device must be in this mode for bit timing and filter set-up.
This is the default following reset. The host exits initialization
mode by selecting an alternative mode of operation.
4
WAKEUP
R/W
0
Wake-Up Enable.
When this bit is set, the HI-5110 will automatically wake up from Sleep Mode to Monitor Mode
when it detects activity on the bus.
1 =
Automatic wake-up enabled. When the device wakes up from
Sleep Mode, the WAKEUP bit will be set in the Interrupt Flag
Register, INTF. A hardware interrupt can be generated at the INT
pin by setting the WAKEUPIE bit in the Interrupt Enable Register.
0 =
Automatic wake-up not enabled. In this case, wake-up from Sleep
Mode is initiated by the host by selecting another mode of
operation. When WAKEUP = 0, all bus activity is ignored.
3
RESET
R/W
0
Setting this bit causes HI-5110 reset to occur. The bit should then be cleared by writing a logic
“0” following reset. A reset may also be performed by setting the MR pin or issuing the “MR” SPI
command, 0x56.
1 =
Master Reset (same as MR pin = 1).
0 =
Normal Operation (same as MR pin = 0).
2
BOR
R/W
0
Bus-off Reset.
When this bit is set, automatic bus-off recovery is initiated following 128 occurrences of 11
consecutive recessive bits on the bus. The HI-5110 will become error-active with both its error
counters set to zero and resume operation in Normal Mode.
1 =
Automatic bus-off recovery.
0 =
The host is responsible for bus-off recovery (default).
1-0 TDIV1:0
R/W
0,0
Time Tag Clock Division Bits <1:0>. See TIMERUB and TIMERLB register descriptions.
00 =
No division (counts every bit clock).
01 =
Divide by 2 (counts every 2 bit clocks).
10 =
Divide by 4 (counts every 4 bit clocks).
11 =
Divide by 8 (counts every 8 bit clocks).
HOLT INTEGRATED CIRCUITS
17
TX
E
TX N
1M
O
SM
FI
LT
O ON
SC
- OF
F
CONTROL REGISTER 1: CTRL1
(Write, SPI Op-code 0x16)
(Read, SPI Op-code 0xD4)
7 6
MSB
5
4
3
2
C
LK
C DIV
LK 1
D
IV
0
HI-5110
1
0
LSB
Bit Name
R/W
Default Description
7
TXEN
R/W
0
Transmission Enable.
This bit is logically ORed with the TXEN pin. When this bit is asserted, each message in the
FIFO will be sequentially loaded to the transmit buffer and sent if the bus is available. If this bit
is not set, a transmission can be enabled by either the TXEN pin or the TX1M bit. If the TXEN
pin is pulled low during a transmission, the current message being transmitted will be
completed. Any additional messages in the FIFO will not be transmitted.
1 =
Enable transmission and send any messages in FIFO (until
empty if TXEN is held set).
0 =
Wait for transmission enable or TX1M bit set before sending next
message in FIFO.
6
TX1M
R/W
0
Enable transmission of only next message.
This bit is applicable only if TXEN = 0. It is reset automatically upon completion of a successful
transmission or by initiation of transmission if the OSM bit is set.
1 =
Enable transmission of only next message in FIFO when TXEN = 0.
0 =
Wait for transmission enable or TX1M bit set before sending next
message in FIFO.
5
OSM
R/W
0
One-Shot Mode Enable.
If enabled, the controller transmits only once and does not attempt re-transmission upon loss
of arbitration or error. This feature is necessary to support the implementation of fixed time
slots in the Time-Triggered CAN standard (TTCAN).
1
0
=
=
Enable one-shot mode.
Messages will re-transmit according to CAN protocol.
4
FILTON
R/W
0
Filter on enable.
This bit is set to turn on the HI-5110 CAN ID filtering mechanism. The default after reset is
FILTON = 0, meaning filtering is turned off and every valid CAN message is accepted into the
receive FIFO. Note: The device must be in initialization mode in order to program the
acceptance filters and masks.
1 =
Enable CAN ID filtering.
0 =
No CAN ID filtering (every valid message accepted into
receive FIFO).
3
OSCOFF
R/W
0
Oscillator off. This bit should be set to a one if an external clock is used. In this case the
external clock is connected to the OSCIN pin and OSCOUT should be left floating.
1 =
Shuts off external OSCOUT pin.
0 =
OSCOUT pin enabled.
2
Not used
R/W
0
R/W
00
1-0 CLKDIV1:0
External CLKOUT division bits <1:0>
00: Divide by 1.
01: Divide by 2.
10: Divide by 4.
11: Divide by 8.
HOLT INTEGRATED CIRCUITS
18
HI-5110
SJ
W
SJ 1
W
BR 0
P
BR 5
P
BR 4
P
BR 3
P
BR 2
P1
BR
P0
BIT TIMING REGISTER 0: BTR0
(Write, SPI Op-code 0x18)
(Read, SPI Op-code 0xD6)
7 6
MSB
5
4
3
2
1
0
LSB
BTR0 defines the value of the Re-synchronization Jump Width (SJW) and the Baud Rate Prescaler (BRP). This register can be read
anytime and written only in init mode (MODE<2:0> bits set to <1xx> in the CTRL0 register).
Bit Name
R/W
7-6 SJW1:0
R/W
Default Description
0
Re-synchronization Jump Width bits <1:0>.
These bits are used to compensate for phase shifts between different clock oscillators on the
bus. They define the maximum number of time quanta (Tq) a bit can be shortened or
lengthened to allow a node achieve re-synchronization to the edge of an incoming signal.
Note that one time quantum (Tq) is the single unit of time within a bit time (see Bit Timing
section).
SJW bits <1:0>
00: SJW = 1 Tq
01: SJW = 2 Tq
10: SJW = 3 Tq
11: SJW = 4 Tq
5-0 BRP5:0
R/W
0
Baud Rate Prescaler bits <5:0>.
The baud rate prescaler relates the system oscillator frequency, fOSC, to the CAN bit time as
described in the bit timing section.
BRP bits <5:0>
000000: BRP = 1
000001: BRP = 2
000010: BRP = 3
000011: BRP = 4
.
etc.
.
111111: BRP = 64
HOLT INTEGRATED CIRCUITS
19
HI-5110
SA
M
TS P
EG
TS 2
E -2
TS G2
E -1
TS G2
E -0
TS G1
E -3
TS G1
E -2
TS G1
EG -1
10
BIT TIMING REGISTER 1: BTR1
(Write, SPI Op-code 0x1A)
(Read, SPI Op-code 0xD8)
7 6
MSB
5
4
3
2
1
0
LSB
BTR1 configures the CAN protocol bit timing segments in terms of time quanta (Tq) and sets the number of sampling points. This
register can be read anytime and written only in init mode (MODE<2:0> bits set to <1xx> in the CTRL0 register).
Bit Name
R/W
7
R/W
SAMP
Default Description
0
Samples per bit.
This bit configures how many samples are taken per bit.
1 =
three samples per bit.
0 =
one sample per bit.
Notes: It is recommended to sample only once at higher CAN bit rates. Bit sampling occurs at
the end of Phase Seg1.
6-4 TSEG2-2:0
R/W
0
Time Segment 2 bits <2:0>.
Tseg2 = Phase Seg2 of the CAN protocol bit timing specification. Bits TSEG2-2:0 specify the
number of time quanta in Phase Seg2. Note: Not all combinations are valid, since Phase Seg
2 must be greater than SJW.
TSEG2 bits <2:0>
000: Not valid
001: Tseg2 = 2 Tq clock cycles
010: Tseg2 = 3 Tq clock cycles
.
etc.
.
111: Tseg2 = 8 Tq clock cycles
3-0 TSEG1-3:0
R/W
0
Time Segment 1 bits <3:0>.
Tseg1 = Prop Seg + Phase Seg1 of the CAN protocol bit timing specification. Bits TSEG1-3:0
specify the number of time quanta in Prop Seg + Phase Seg1. Note: Not all combinations are
valid, since Prop Seg + Phase Seg1 ³ Phase Seg 2. The CAN protocol states that the
minimum number of Tq in a bit time shall be 8.
TSEG1 bits <3:0>
0000: Not valid
0001: Tseg1 = 2 Tq clock cycles
0010: Tseg1 = 3 Tq clock cycles
0011: Tseg1 = 4 Tq clock cycles
0100: Tseg1 = 5 Tq clock cycles
.
.
.
1111: Tseg1 = 16 Tq clock cycles
HOLT INTEGRATED CIRCUITS
20
HI-5110
TRANSMIT ERROR COUNTER REGISTER: TEC
TEC7:0
(Write, SPI Op-code 0x26)
(Read, SPI Op-code 0xEC)
7 6
MSB
5
4
3
2
1
0
LSB
The TEC register reflects the current value of the CAN Transmit Error Counter. This register can be written by SPI command for test
purposes.
Bit Name
R/W
7-0 TEC7:0
R/W
Default Description
0x00
Transmit Error Counter bits <7:0>.
0 £ TEC £ 95: Error active status.
96£ TEC £ 127: Error active status. Error warning flag, ERRW, set in STATF register. This
may be used to generate a hardware interrupt if ERRWIE bit is set in STATFE register.
128 £ TEC£ 255: Error passive status. Transmit error passive flag, TXERRP, set in ERR
register. ERRP also set in STATF register. This may be used to generate a hardware interrupt if
ERRPIE bit is set in STATFE register.
TEC > 255: Bus-off status. Bus-off flags, BUSOFF, set in ERR and STATF registers. The
latter may be used to generate a hardware interrupt if BUSOFFIE bit is set in STATFE register.
The HI-5110 will, after entering bus-off state, automatically recover to error active status
without host intervention if the BOR bit is set in control register CTRL0 and 128 x 11
consecutive recessive bits are detected on the bus. If the BOR bit is not set, bus-off recovery is
managed by the host.
RECEIVE ERROR COUNTER REGISTER: REC
REC7:0
(Write, SPI Op-code 0x24)
(Read, SPI Op-code 0xEA)
7 6
MSB
5
4
3
2
1
0
LSB
The REC register reflects the current value of the CAN Receive Error Counter. This register can be written by SPI command for test
purposes.
Bit Name
R/W
7-0 TEC7:0
R/W
Default Description
0x00
Receiver Error Counter bits <7:0>.
0 £ REC £ 95: Error active status.
96 £ REC £ 127: Error active status. Error warning flag, ERRW, set in STATF register. This
may be used to generate a hardware interrupt if ERRWIE bit is set in STATFE register.
128 £ REC £ 255: Error passive status. Receive error passive flag, RXERRP, set in ERR
register. ERRP also set in STATF register. This may be used to generate a hardware interrupt if
ERRPIE bit is set in STATFE register.
HOLT INTEGRATED CIRCUITS
21
MESSAGE STATUS REGISTER: MESSTAT
(Read only)
(Read, SPI Op-code 0xDA)
FI
LH
FI IT3
LH
FI IT2
LH
FI IT1
LH
M IT0
TA
M G1
TA
TS G0
TA
TS T1
TA
T0
HI-5110
7 6
MSB
5
4
3
2
1
0
LSB
This register reflects transmission status and also which filters were responsible for filtering valid received messages. It is read-only.
Bit Name
7-4 FILHIT3:0
R/W
R
Default Description
0
Filter hit bits <3:0>.
These bit combinations indicate which filters were responsible for filtering received messages
.
0000: No filter matches the received message.
1000: Filter 0 matches, but filters 1, 2, 3, 4, 5, 6 or 7 may also match.
1001: Filter 1 matches, filter 0 does not, but filters 2, 3, 4, 5, 6 or 7 may also match.
1010: Filter 2 matches, filters 0 and 1 do not, but filters 3, 4, 5, 6 or 7 may also match.
1011: Filter 3 matches, filters 0 through 2 do not, but filters 4, 5, 6 or 7 may also match.
1100: Filter 4 matches, filters 0 through 3 do not, but filters 5, 6, or 7 may also match.
1101: Filter 5 matches, filters 0 through 4 do not, but filters 6 or 7 may also match.
1110: Filter 6 matches, filters 0 through 5 do not, but filter 7 may also match.
1111: Filter 7 matches, all other filters do not.
Note:
Filter checking is carried out by the internal logic in order of increasing filter
number. Once a filter matches, no further checking takes place. Therefore, in
the case of more than one filter matching for a given message, the lowest
filter will be given priority and the FILHIT3:0 bits will reflect this value.
3-2 MTAG1:0
R
0
Message Tag bits <1:0>.
These bits will reflect the last two bits of the host assigned message tag of the last successful
transmission.
1-0 TSTAT1:0
R
0
Transmission Status bits <1:0>.
These bits reflect the transmission status.
00: Transmission not enabled (TXEN = 0).
01: Transmission is enabled (TXEN = 1), but FIFO is empty.
10: Waiting to transmit or re-transmit.
11: Transmitter is currently transmitting a message or a flag.
HOLT INTEGRATED CIRCUITS
22
S
TX O F
ER F
R R
XE P
BI RR
TE P
FR RR
M
C ER
R R
C
AC ER
KE R
ST R
U R
FE
R
R
HI-5110
BU
ERROR REGISTER: ERR
(Read only)
(Read, SPI Op-code 0xDC)
7 6
MSB
5
4
3
2
1
0
LSB
The ERR register indicates CAN bus status and protocol errors. It is read only. All bits default to 0 at power up and maintain their
current status following reset. Bits 4:0 are reset following a host read.
Bit Name
R/W
Default Description
7
BUSOFF
R
0
Bus-off status indicator.
This bit is set when TEC > 255. Node is in bus off condition. The bit is reset by HI-5110 when a
successful bus recovery sequence is detected (128 x 11 consecutive recessive bits). d the
FILHIT3:0 bits will reflect this value.
6
TXERRP
R
0
Transmit Error Passive status indicator.
This bit is set when 128 £ TEC £ 255.
5
RXERRP
R
0
Receive Error Passive status indicator.
This bit is set when 128 £ REC £ 255.
4
BITERR
R
0
Bit Error.
A bit error was detected in a transmitted frame (the bit observed on the bus was opposite to
what was expected).
3
FRMERR
R
0
Form Error.
A Form error was detected in a receive frame.
2
CRCERR
R
0
CRC Error.
A CRC error was detected in a receive frame.
1
ACKERR
R
0
Acknowledgement Error.
An ACK error was detected in a receive frame.
0
STUFERR
R
0
Stuff Error.
A bit stuffing error was detected in a received frame.
HOLT INTEGRATED CIRCUITS
23
HI-5110
R
XT
R MP
XF
TX IFO
C
BU PLT
S
M ER
C R
H
W G
AK
F1 EU
M P
F0 ES
M S
ES
INTERRUPT FLAG REGISTER: INTF
(Read only)
(Read, SPI Op-code 0xDE)
7 6
MSB
5
4
3
2
1
0
LSB
The Interrupt Flag Register INTF bits will be set by HI-5110 when the corresponding related events described below occur. If
individual bits in the Interrupt Enable Register INTE are set, the INT pin will be latched high when any of the corresponding INTF bits
are set. This alerts the host that one of the conditions below has occurred. Reading this register will clear all bits and reset the INT pin.
The value of individual bits in the INTF register may also be reflected on the GP1 and GP2 pins by setting the correct bit combinations
in the General Purpose Pins Enable Register GPINE (see section General Purpose Pins Enable Register).
Bit Name
R/W
Default Description
7
RXTMP
R
0
Message received in temporary receive buffer (unfiltered).
This bit is set when a valid message is received in the temporary receive buffer.
6
RXFIFO
R
0
Message received in FIFO (filtered).
This bit is set when a valid message passes the filter criteria and is passed from the
temporary receive buffer to the receive FIFO.
5
TXCPLT
R
0
Successful transmission complete.
This bit is set when a message is successfully transmitted.
4
BUSERR
R
0
Bus Error.
This bit is set when a bus error occurs. Bits 4:0 in the ERR register can be read to determine
the source of the error.
3
MCHG
R
0
Mode Change bit.
This bit is set when the mode of operation is changed. Any pending transmissions in the
transmit FIFO will be completed (FIFO will be emptied) before the mode change occurs.
2
WAKEUP
R
0
Wake-Up detected.
This bit is set when the HI-5110 wakes up from Sleep Mode in response to bus activity.
1
F1MESS
R
0
Filter 1 passed a valid message.
This bit is set when receive filter one passes a valid message. FILHIT3:0 bits will also be set to
<1001> in the Message Status Register, MESSTAT.
0
F0MESS
R
0
Filter 0 passed a valid message.
This bit is set when receive filter zero passes a valid message. FILHIT3:0 bits will also be set to
<1000> in the Message Status Register, MESSTAT.
HOLT INTEGRATED CIRCUITS
24
R
INTERRUPT ENABLE REGISTER: INTE
XT
R MP
XF IE
TX IFO
C IE
BU PLT
S IE
M ER
C R
H I
W GI E
AK E
F1 EU
M PI
F0 ES E
M SIE
ES
IE
HI-5110
(Write SPI Op-code 0x1C)
(Read, SPI Op-code 0xE4)
7 6
MSB
5
4
3
2
1
0
LSB
Setting bits in the Interrupt Enable Register causes a hardware interrupt to be generated at the INT pin when the corresponding bits in
the Interrupt Flag Register are set by HI-5110 as a result of the related events described below.
Bit Name
R/W
7
RXTMPIE
R/W
0
Enable interrupt when a message is received in the temporary receive buffer (unfiltered).
Setting this bit causes a hardware interrupt to be generated at the INT pin when the RXTMP bit
is set in the INTF register.
6
RXFIFOIE
R/W
0
Enable interrupt when a message is received in the receive FIFO (filtered).
Setting this bit causes a hardware interrupt to be generated at the INT pin when the
RXFIFO bit is set in the INTF register.
5
TXCPLTIE
R/W
0
Enable interrupt when a successful transmission is complete.
Setting this bit causes a hardware interrupt to be generated at the INT pin when the TXCPLT bit
is set in the INTF register.
4
BUSERRIE
R/W
0
Enable interrupt when a bus error occurs.
Setting this bit causes a hardware interrupt to be generated at the INT pin when the BUSERR
bit is set in the INTF register.
3
MCHGIE
R/W
0
Enable interrupt when a mode change occurs.
Setting this bit causes a hardware interrupt to be generated at the INT pin when the MCHG bit
is set in the INTF register.
2
WAKEUPIE
R/W
0
Enable interrupt when HI-5110 wakes up from Sleep Mode.
Setting this bit causes a hardware interrupt to be generated at the INT pin when the WAKEUP
bit is set in the INTF register.
1
F1MESSIE
R/W
0
Enable interrupt when filter one passes a message.
Setting this bit causes a hardware interrupt to be generated at the INT pin when the F1MESS
bit is set in the INTF register.
0
F0MESSIE
R/W
0
Enable interrupt when filter zero passes a message.
Setting this bit causes a hardware interrupt to be generated at the INT pin when the F0MESS
bit is set in the INTF register.
Default Description
HOLT INTEGRATED CIRCUITS
25
HI-5110
TX
M
TX T Y
F
TX U L L
H
ER ISF
R
ER W
R
BU P
S
R OF
XF F
R MT
XF Y
FU
LL
STATUS FLAG REGISTER: STATF
(Read-only)
(Read, SPI Op-code 0xE2)
7 6
MSB
5
4
3
2
1
0
LSB
The Status Flag Register STATF bits will be set by HI-5110 when the corresponding related events described below occur. Unlike the
Interrupt Flag Register, reading this register will NOT clear all bits. These bits are reset automatically by HI-5110 when the described
status for each bit changes (e.g. if TXMTY is set and a message is loaded to the transmit FIFO, TXMTY will be automatically cleared
by HI-5110). If individual bits in the Status Flag Enable Register STATFE are set, the STAT pin will pulse high when any of the enabled
STATF bits are set. The value of individual bits in the STATF register may also be reflected on the GP1 and GP2 pins by setting the
correct bit combinations in the General Purpose Pins Enable Register GPINE.
Bit Name
R/W
Default Description
7
TXMTY
R
1
Transmit FIFO is empty.
This bit is set when the transmit FIFO is empty. This is the default following Reset.
6
TXFULL
R
0
Transmit FIFO is full.
This bit is set when the transmit FIFO is full.
5
TXHISF
R
0
Transmit history FIFO full.
This bit is set when the transmit history FIFO is full. Up to eight messages can be stored in the
transmit history FIFO (Note: a user generated message tag and a time tag are stored with each
message).
4
ERRW
R
0
Error warning flag.
This bit is set when 96 £ (TEC or REC) £ 127.
3
ERRP
R
0
Error passive indicator.
This bit is set when the device enters error passive mode.
2
BUSOFF
R
0
BUSOFF indicator.
This bit is set when the device enters bus-off state.
1
RXFMTY
R
1
Receive FIFO empty.
This bit is set when the receive FIFO is empty. This is the default following Reset.
0
RXFFULL
R
0
Receive FIFO full.
This bit is set when the receive FIFO is full.
HOLT INTEGRATED CIRCUITS
26
TX
STATUS FLAG ENABLE REGISTER: STATE
M
TX T Y
F FE
TX U L L
H FE
ER ISF
R FE
ER WF
R E
BU PF
S E
R OF
XF F
F
R MT E
XF Y
FU FE
LL
FE
HI-5110
(Write, SPI Po-code 0x1E)
(Read, SPI Op-code 0xE6)
7 6
MSB
5
4
3
2
1
0
LSB
Setting bits in the Status Flag Enable Register causes the STAT pin to go high when any of the corresponding bits in the Status Flag
Register are set by HI-5110 as a result of the related events described below.
Bit Name
R/W
Default Description
7
TXMTYFE
R/W
1
Transmit FIFO empty status flag enable.
Setting this bit causes the status of the TXMTY bit in the Status Flag Register to be output on
the STAT pin.
6
TXFULLFE
R/W
0
Transmit FIFO full status flag enable.
Setting this bit causes the status of the TXFULL bit in the Status Flag Register to be output on
the STAT pin.
5
TXHISFFE
R/W
0
Transmit History FIFO full status flag enable.
Setting this bit causes the status of the TXHISF bit in the Status Flag Register to be output on
the STAT pin.
4
ERRWFE
R/W
0
Error warning status flag enable (96 £ (TEC or REC) £ 127).
Setting this bit causes the status of the ERRW bit in the Status Flag Register to be output on the
STAT pin.
3
ERRPFE
R/W
0
Error Passive status flag enable.
Setting this bit causes the status of the ERRP bit in the Status Flag Register to be output on the
STAT pin.
2
BUSOFFFE
R/W
0
Bus-off status flag enable.
Setting this bit causes the status of the BUSOFF bit in the Status Flag Register to be output on
the STAT pin.
1
RXFMTYFE
R/W
1
Receive FIFO empty status flag enable.
Setting this bit causes the status of the RXFMTY bit in the Status Flag Register to be output on
the STAT pin.
0
RXFFULLFE
R/W
0
Receive FIFO full status flag enable.
Setting this bit causes the status of the RXFFULL bit in the Status Flag Register to be output on
the STAT pin.
HOLT INTEGRATED CIRCUITS
27
HI-5110
GENERAL PURPOSE PINS ENABLE REGISTER: GPINE
GPINE7:4
GPINE3:0
(Write, SPI Op-code 0x22)
(Read, SPI Op-code 0xE8)
7 6
MSB
5
4
3
2
1
0
LSB
Setting bits in the General Purpose Pins Enable Register allows the user to reflect the values of the Interrupt Flag bits in the INTF
Register or the Status Flag bits in the STATF Register on the GP1 andGP2 pins.
Bit Name
R/W
7-4 GPINE7:43:0
R/W
3-0 GPINE3:0
R/W
Default Description
0000
0000
Reflect status of interrupt flag bits in INTF or status flag bits in STATF on GP2 pin as follows:
0000:
0001:
0010:
0011:
0100:
0101:
0110:
0111:
GP2 pin is asserted when F0MESS bit is set in register INTF.
GP2 pin is asserted when F1MESS bit is set in register INTF.
GP2 pin is asserted when WAKEUP bit is set in register INTF.
GP2 pin is asserted when MCHG bit is set in register INTF.
GP2 pin is asserted when BUSERR bit is set in register INTF.
GP2 pin is asserted when TXCPLT bit is set in register INTF.
GP2 pin is asserted when RXFIFO bit is set in register INTF.
GP2 pin is asserted when RXTMP bit is set in register INTF.
1000:
1001:
1010:
1011:
1100:
1101:
1110:
1111:
GP2 pin is asserted when RXFFULL bit is set in register STATF.
GP2 pin is asserted when RXFMPTY bit is set in register STATF.
GP2 pin is asserted when BUSOFF bit is set in register STATF.
GP2 pin is asserted when ERRP bit is set in register STATF.
GP2 pin is asserted when ERRW bit is set in register STATF.
GP2 pin is asserted when TXHISF bit is set in register STATF.
GP2 pin is asserted when TXFULL bit is set in register STATF.
GP2 pin is asserted when TXMPTY bit is set in register STATF.
Reflect status of interrupt flag bits in INTF or status flag bits in STATF on GP1 pin as follow:
0000:
0001:
0010:
0011:
0100:
0101:
0110:
0111:
GP1 pin is asserted when F0MESS bit is set in register INTF.
GP1 pin is asserted when F1MESS bit is set in register INTF.
GP1 pin is asserted when WAKEUP bit is set in register INTF.
GP1 pin is asserted when MCHG bit is set in register INTF.
GP1 pin is asserted when BUSERR bit is set in register INTF.
GP1 pin is asserted when TXCPLT bit is set in register INTF.
GP1 pin is asserted when RXFIFO bit is set in register INTF.
GP1 pin is asserted when RXTMP bit is set in register INTF.
1000:
1001:
1010:
1011:
1100:
1101:
1110:
1111:
GP1 pin is asserted when RXFFULL bit is set in register STATF.
GP1 pin is asserted when RXFMPTY bit is set in register STATF.
GP1 pin is asserted when BUSOFF bit is set in register STATF.
GP1 pin is asserted when ERRP bit is set in register STATF.
GP1 pin is asserted when ERRW bit is set in register STATF.
GP1 pin is asserted when TXHISF bit is set in register STATF.
GP1 pin is asserted when TXFULL bit is set in register STATF.
GP1 pin is asserted when TXMPTY bit is set in register STATF.
HOLT INTEGRATED CIRCUITS
28
HI-5110
FREE-RUNNINGG TIMER UPPER BYTE: TIMERUB
T15:8
(Read-only)
(Read, SPI Op-code 0xFA)
7 6
MSB
Bit Name
R/W
7-0 T15:8
R/W
5
4
3
2
1
0
LSB
Default Description
0x00
Free Running Timer Upper Byte, bits <15:8>.
The 16-bit free-running timer starts counting from zero following RESET. The timer counts
linearly up to 0xFFFF and then wraps around to 0x0000. Note: A timer overrun is not
flagged by the HI-5110. The timer is clocked by the HI-5110 bit clock and continuously
increments by the bit rate (default). The user may program the timer to 2, 4 or 8 bit clocks by
setting the TTDIV1:0 bits in Control Register 0, CTRL0.
The timer may be reset by the host after any interrupt condition (e.g. reading the receive buffer,
transmit FIFO empty, etc), by issuing an SPI instruction (see Table 1, SPI Instruction Set).
FREE-RUNNINGG TIMER LOWER BYTE: TIMERLB
T7:0
(Read-only)
(Read, SPI Op-code 0xFA)
7 6
MSB
Bit Name
R/W
7-0 T7:0
R/W
5
4
3
2
1
Default Description
0x00
Free Running Timer Lower Byte, bits <7:0>.
HOLT INTEGRATED CIRCUITS
29
0
LSB
HI-5110
SERIAL PERIPHERAL INTERFACE
SERIAL PERIPHERAL INTERFACE (SPI) BASICS
edges on SCK latch input data into the master and slave
devices, starting with each byte’s most-significant bit. The
HI-5110 SPI can be clocked at 20 MHz.
The HI-5110 uses an SPI synchronous serial interface for
host access to internal registers and data FIFOs. Host
serial communication is enabled through the Chip Select
(CS) pin, and is accessed via a three-wire interface
consisting of Serial Data Input (SI) from the host, Serial
Data Output (SO) to the host and Serial Clock (SCK). All
read / write cycles are completely self-timed.
Multiple bytes may be transferred when the host holds CS
low after the first byte transferred, and continues to clock
SCK in multiples of 8 clocks. A rising edge on CS chip
select terminates the serial transfer and reinitializes the
HI-5110 SPI for the next transfer. If CS goes high before a
full byte is clocked by SCK, the incomplete byte clocked
into the device SI pin is discarded.
The SPI (Serial Peripheral Interface) protocol specifies
master and slave operation; the HI-5110 operates as an
SPI slave.
In the general case, both master and slave simultaneously
send and receive serial data (full duplex), per Figure 9
below. However the HI-5110 operates half duplex,
maintaining high impedance on the SO output, except
when actually transmitting serial data. When the HI-5110
is sending data on SO during read operations, activity on
its SI input is ignored. Figures 10 and 11 show actual
behavior for the HI-5110 SO output.
The SPI protocol defines two parameters, CPOL (clock
polarity) and CPHA (clock phase). The possible CPOLCPHA combinations define four possible "SPI Modes".
Without describing details of the SPI modes, the HI-5110
operates in mode 0 where input data for each device
(master and slave) is clocked on the rising edge of SCK,
and output data for each device changes on the falling
edge (CPHA = 0, CPOL = 0). Be sure to set the host SPI
logic for mode 0.
As seen in Figure 9, SPI Mode 0 holds SCK in the low state
when idle. The SPI protocol transfers serial data as 8-bit
bytes. Once CS chip select is asserted, the next 8 rising
SCK (SPI Mode 0)
SI
SO
High Z
0
1
2
3
4
5
6
7
MSB
LSB
MSB
LSB
CS
Figure 9. Generalized Single-Byte Transfer Using SPI Protocol Mode 0
HOLT INTEGRATED CIRCUITS
30
High Z
HI-5110
HOST SERIAL PERIPHERAL INTERFACE, cont.
HI-5110 SPI COMMANDS
Multiple byte read or write cycles may be performed by
transferring more than one byte before CS is negated.
Tables 2 - 5 define the required number of bytes for each
instruction.
For the HI-5110, each SPI read or write operation begins
with an 8-bit command byte transferred from the host to the
device after assertion of CS. Since HI-5110 command byte
reception is half-duplex, the host discards the dummy byte
it receives while serially transmitting the command byte.
Note: SPI Instruction op-codes not shown in Tables 2 - 5
are “reserved” and must not be used. Further, these opcodes will not provide meaningful data in response to read
commands.
Figures 10 and 11 show read and write timing as it appears
for a single-byte and dual-byte register operation. The
command byte is immediately followed by a data byte
comprising the 8-bit data word read or written. For a single
register read or write, CS is negated after the data byte is
transferred.
0
1
2
3
4
5
6
Two instruction bytes cannot be “chained”; CS must
be negated after the command, then reasserted for the
following Read or Write command.
7
0
1
2
3
4
5
6
7
SCK
MSB
LSB
SI
Op-Code Byte
LSB MSB
MSB
High Z
SO
High Z
Data Byte
CS
Host may continue to assert CS
here to read sequential word(s)
when allowed by the instruction.
Each word needs 8 SCK clocks.
Figure 10. Single-Byte Read From a Register
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
SCK
SPI Mode 0
MSB
LSB MSB
LSB
LSB MSB
SI
Op-Code Byte
SO
Data Byte 0
Data Byte 1
High Z
CS
Host may continue to assert CS
here to write sequential byte(s)
when allowed by the SPI instruction.
Each byte needs 8 SCK clocks.
Figure 11. 2-Byte Write example
HOLT INTEGRATED CIRCUITS
31
HI-5110
Table 1. SPI Instruction Set
SPI Instruction
Command
Hex
Data Field
Bit Content
Read Temporary Receive
Buffer with Time Tag
0x42
15 bytes
(see Table 5, bytes 2-16)
Read Temporary Receive
Buffer without Time Tag
0x44
13 bytes
(see Table 5, bytes 4-16)
Read Next FIFO Message
with Time Tag
0x46
16 bytes
(see Table 5, bytes 1-16)
Read Next FIFO Message
without Time Tag
0x48
14 bytes
(see Table 5, bytes 1 & 4-16)
Read Next FIFO Message
Data only with Time Tag
0x4A
11 bytes
(see Table 5, bytes 1-3 & 9-16)
Read Next FIFO Message
Data only without Time Tag
0x4C
9 bytes
(see Table 5, bytes 1 & 9-16)
Read Filter 0 ID
Read Filter 1 ID
Read Filter 2 ID
Read Filter 3 ID
Read Filter 4 ID
Read Filter 5 ID
Read Filter 6 ID
Read Filter 7 ID
0xA2
0xA4
0xA6
0xA8
0xAA
0xAC
0xAE
0xB2
6 bytes
6 bytes
6 bytes
6 bytes
6 bytes
6 bytes
6 bytes
6 bytes
(see Table 4a)
(see Table 4a)
(see Table 4a)
(see Table 4a)
(see Table 4a)
(see Table 4a)
(see Table 4a)
(see Table 4a)
Read Mask 0 ID
Read Mask 1 ID
Read Mask 2 ID
Read Mask 3 ID
Read Mask 4 ID
Read Mask 5 ID
Read Mask 6 ID
Read Mask 7 ID
0xB4
0xB6
0xB8
0xBA
0xBC
0xBE
0xC2
0xC4
6 bytes
6 bytes
6 bytes
6 bytes
6 bytes
6 bytes
6 bytes
6 bytes
(see Table 4b)
(see Table 4b)
(see Table 4b)
(see Table 4b)
(see Table 4b)
(see Table 4b)
(see Table 4b)
(see Table 4b)
Read Control Register 0
Read Control Register 1
0xD2
0xD4
1 byte
1 byte
(see CTRL0 Register Definition)
(see CTRL1 Register Definition)
Read Bit Timing Register 0
Read Bit Timing Register 1
0xD6
0xD8
1 byte
1 byte
(see BTR0 Register Definition)
(see BTR1 Register Definition)
Read Message Status Register
Read Error Register
0xDA
0xDC
1 byte
1 byte
(see MESSTAT Register Definition)
(see ERR Register Definition)
Read Interrupt Flag Register
Read Status Flag Register
0xDE
0xE2
1 byte
1 byte
(see INTF Register Definition)
(see STATF Register Definition)
Read Interrupt Enable Register
Read Status Flag Enable Register
0xE4
0xE6
1 byte
1 byte
(see INTE Register Definition)
(see STATFE Register Definition)
READ Commands
HOLT INTEGRATED CIRCUITS
32
HI-5110
Table 1. SPI Instruction Set (cont.)
SPI Instruction
Command
Hex
Data Field
Bit Content
Read General Purpose Pins
Enable Register
0xE8
1 byte
(see GPINE Register Definition)
Read REC Register
Read TEC Register
0xEA
0xEC
1 byte
1 byte
(see REC Register Definition)
(see TEC Register Definition)
Read Transmit History FIFO
0xEE
3 bytes
(see Table 3)
Reserved
(Factory test purposes only)
0x4E
13 bytes
Reserved
(Factory test purposes only)
0xF4
1 byte
Reserved
(Factory test purposes only)
0xF6
1 byte
Read Bus-Off Recessive Count
0xF8
1 byte
Read Time Tag
0xFA
2 bytes
(see TIMERUB and TIMERLB
Register Definitions)
Abort Transmission
(stops current transmission and
resets TXEN & TX1M)
0x52
None
(see CTRL1 Register Definition)
Reset (Clear) Transmit FIFO
(resets TXEN & TX1M, but
completes current transmission)
0x54
None
Master Reset
0x56
None
Reset Time Tag Counter
0x58
None
Reset Receive FIFO
0x5A
None
READ Commands (ctd)
RESET Commands
HOLT INTEGRATED CIRCUITS
33
(see TIMERUB and TIMERLB
Register Definitions)
HI-5110
Table 1. SPI Instruction Set (cont.)
SPI Instruction
Command
Hex
Data Field
Bit Content
WRITE Commands
Write Transmit FIFO
0x12
N x (4 to 12 bytes) for Std frame or
N x (6 to 14 bytes) for Ext frame
(N = number of loaded messages, 1 - 8)
Write Control Register 0
Write Control Register 1
0x14
0x16
1 byte
1 byte
(see CTRL0 Register Definition)
(see CTRL1 Register Definition)
Write Bit Timing Register 0
Write Bit Timing Register 1
0x18
0x1A
1 byte
1 byte
(see BTR0 Register Definition)
(see BTR1 Register Definition)
Write Interrupt Enable Register
0x1C
1 byte
(see INTE Register Definition)
Write Status Flag Enable Register
0x1E
1 byte
(see STATFE Register Definition)
Write General Purpose Pins
Enable Register
0x22
1 byte
(see GPINE Register Definition)
Write REC Register (Test only)
Write TEC Register (Test only)
0x24
0x26
1 byte
1 byte
(see REC Register Definition)
(see TEC Register Definition)
Write Filter 0 ID
Write Filter 1 ID
Write Filter 2 ID
Write Filter 3 ID
Write Filter 4 ID
Write Filter 5 ID
Write Filter 6 ID
Write Filter 7 ID
0x62
0x64
0x66
0x68
0x6A
0x6C
0x6E
0x72
6 bytes
6 bytes
6 bytes
6 bytes
6 bytes
6 bytes
6 bytes
6 bytes
(see Table 4a)
(see Table 4a)
(see Table 4a)
(see Table 4a)
(see Table 4a)
(see Table 4a)
(see Table 4a)
(see Table 4a)
Write Mask 0 ID
Write Mask 1 ID
Write Mask 2 ID
Write Mask 3 ID
Write Mask 4 ID
Write Mask 5 ID
Write Mask 6 ID
Write Mask 7 ID
0x74
0x76
0x78
0x7A
0x7C
0x7E
0x82
0x84
6 bytes
6 bytes
6 bytes
6 bytes
6 bytes
6 bytes
6 bytes
6 bytes
(see Table 4b)
(see Table 4b)
(see Table 4b)
(see Table 4b)
(see Table 4b)
(see Table 4b)
(see Table 4b)
(see Table 4b)
HOLT INTEGRATED CIRCUITS
34
HI-5110
HI-5110 Transmit Buffer
The HI-5110 transmit buffer consists of an eight message
FIFO which allows transmission of up to eight messages.
Messages are loaded to the transmit FIFO via SPI
instruction. Similarly, an SPI instruction resets (clears) the
transmit FIFO.
Transmission from the FIFO is enabled by asserting the
TXEN pin or setting the TXEN bit in CTRL1. If transmission
is enabled, all loaded messages are automatically sent if the
bus is available. If TXEN is not enabled, messages will not
be sent until TXEN is set. If TXEN is reset, a single message
may also be sent by setting the TX1M bit in CTRL1.
MESSAGE TRANSMISSION SEQUENCE
A simplified transmission flow is illustrated in Figure 9. The
next message to be transmitted (or current message trying
to gain access to the bus) is loaded from the FIFO to the
Transmit Buffer. This will happen automatically if TXEN or
TX1M are set in CTRL1.
If the bus is available, the message is sent.
The
transmission can be aborted at any time using the Abort
Transmission SPI command (see Table 1). Care should be
exercised when using the command as it may cause other
nodes on the bus to generate error frames if the message is
aborted prior to completing transmission. The current
transmission sequence can also be paused by resetting the
TXEN bit in CTRL1 (or pulling TXEN pin low). In this case,
the current message will be completed and any remaining
messages in the transmit FIFO will not be transmitted.
If the current message transmission goes ahead, two things
can happen:
a) The message is successful, and the transmit buffer is now
ready to receive the next message from the transmit FIFO.
The transmit history FIFO is updated (see below).
b) The message is not successful due to lost arbitration or
message error.
i. Lost Arbitration: If arbitration is lost, the current
message stays in the Transmit Buffer for
re-transmission provided OSM is not set. If OSM is
set, the next message is loaded to the transmit
buffer for transmission, provided TXEN or TX1M is
set. In this case, the current message is lost and it is
up to the user to re-load and initiate a
re-transmission.
ii. Message error: Flag BUSERR is set in the
Interrupt Flag Register. An error frame is sent and
an optional hardware interrupt may also be
generated at the INT pin if enabled in the Interrupt
Enable Register (bit BUSERRIE = 1). If there is an
error, the current message stays in the Transmit
Buffer for automatic re-transmission in accordance
with the CAN protocol, provided OSM is not set.
If OSM is set, the next message is loaded to the
transmit buffer for transmission, provided TXEN or
TX1M is set. In this case, the current message is
lost and it is up to the user to re-load and initiate a
re-transmission.
LOADING THE TRANSMIT FIFO VIA SPI
The transmit FIFO is loaded via SPI instruction (see Table 1).
The data format for the SPI instruction is illustrated in Table
2. The host simply needs to issue the SPI write command
0x12 followed by the SPI data field as described in Table 2.
For standard frames, the SPI data field has the format shown
in Table 2(a). For extended frames, the SPI data field has
the format shown in Table 2(b).
The HI-5110 will
automatically interpret Standard or Extended frames by
decoding the IDE bit. The HI-5110 also decodes the data
length code (DLC) and ignores data bytes greater than the
DLC value (Note: a DLC of greater than 8 is automatically
assumed to be equal to 8). The user has the option of
assigning a unique message tag to each message which
can be used later to identify successfully transmitted
messages from the transmit history FIFO. Up to 8 frames
can be loaded to the transmit FIFO for transmission. The
byte format should be as shown in Table 2 and the CS pin
should remain low during the entire SPI sequence.
TRANSMIT HISTORY FIFO
The Transmit History FIFO can optionally be used by the
host to keep a record of up to eight successfully transmitted
messages. A user-assigned message tag and a time tag are
stored for each message. The data format is shown in Table
3. The time tag is assigned from the value of the free running
counter upon receipt of an ACK bit. The transmit history
FIFO is cleared when read by SPI command 0xEE (see
Table 3).
HOLT INTEGRATED CIRCUITS
35
HOLT INTEGRATED CIRCUITS
36
NO
TX1M = 1?
NO
TXEN = 1?
Message 1
Message 2
Message 3
Message 4
Message 5
Message 6
Message 7
Message 8
Write Tx FIFO
YES
YES
YES
Is CAN bus
available?
NO
NO
Message error or
lost arbitration?
Message
Error
Transmit
Buffer keeps
current message
Lost
Arbitration
Set BUSERR
flag
Is BUSERRIE
set?
YES
Generate
Interrupt at pin
Figure 12. Simplified Transmission Flow Diagram
Write Transmit
History FIFO
YES
Successful message
transmission?
Transmit message
Load Transmit
Buffer with
next message
Transmit
Buffer
NO
OSM = 1
YES
OSM = 1?
NO
OSM = 0
HI-5110
HI-5110 Transmit Message Flow Diagram
HI-5110
Table 2. SPI Transmit Data Format
a) Standard Frame Transmit
Byte Content
Bit Description (”x” = Don’t care)
1
Message Tag*
2
ID28 to ID21
3
ID20 to ID18, RTR, IDE
4
r0, DLC3 to DLC0
5
*Data Byte 1
6
Data Byte 2
7
Data Byte 3
8
Data Byte 4
9
Data Byte 5
10
Data Byte 6
11
Data Byte 7
12
Data Byte 8
MT
7
MT
6
MT
5
MT
4
MT
3
MT
2
Byte
ID
18
RT
R
ID
E
ID
ID
20
ID
21
28
x x
r0
DL
C3
DL
C2
DL
C
DL 1
C0
x x x
DB
DB
0
7
x x x
0
DB
DB
7
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
* Note: The Message Tag is a host-assigned identifier that is stored along with a time tag in the Transmit
History FIFO. It can be used by the host to log successfully transmitted messages at a later time.
HOLT INTEGRATED CIRCUITS
37
HI-5110
Table 2. SPI Transmit Data Format
b) Extended Frame Transmit
Content
Bit Description (”x” = Don’t care)
1
Message Tag*
2
ID28 to ID21
3
ID20 to ID18, SRR, IDE,
ID17 to ID15
4
ID14 to ID7
5
ID6 to ID0, RTR
6
r0, r1, DLC3 to DLC0
7
Data Byte 1
MT
7
MT
6
MT
5
MT
4
MT
3
MT
2
Byte
15
17
ID
ID
18
SR
R
ID
E
ID
Data Byte 3
10
Data Byte 4
11
Data Byte 5
12
Data Byte 6
13
Data Byte 7
14
Data Byte 8
DB
0
9
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
DB
Data Byte 2
DB
DB
0
7
x x
7
8
RT
R
DL
C3
DL
C2
DL
C1
DL
C0
r1
r0
ID
6
ID
0
ID
ID
7
14
ID
20
ID
ID
21
28
x x
* Note: The Message Tag is a host-assigned identifier that is stored along with a time tag in the Transmit
History FIFO. It can be used by the host to log successfully transmitted messages at a later time.
HOLT INTEGRATED CIRCUITS
38
HI-5110
Table 3. Transmit History FIFO Data Format
Content
Bit Description (”x” = Don’t care)
1
Message Tag
2
Time Tag Upper Byte
3
Time Tag Lower Byte
MT
7
MT
6
MT
5
MT
4
MT
3
MT
2
Byte
HI-5110 Receive Buffers and Frame
Acceptance Filters
RECEIVE BUFFERS
The HI-5110 has an extremely flexible receive buffer and ID
filter scheme. Acceptance filters and masks may only be
programmed when the device is in Initialization Mode.
The basic concept is shown in figure 13. All valid received
messages (both standard or extended frames) are stored in
the temporary receive buffer before passing through the
filter bank. The host can read the temporary receive buffer
using SPI commands 0x42 or 0x44 (see table 1). The filter
bank must be enabled by setting the FILTON bit in Control
Register, CTRL1. The default after reset is FILTON = 0,
which disables the filter bank and stores every valid
message received in the FIFO. With filtering enabled, it is
possible to filter up to eight extended identifiers plus the first
two associated data bytes. Any filtered messages will be
passed to the receive FIFO. Up to eight messages can be
stored in the receive FIFO. All valid received messages
have a 16-bit time tag appended following transmission of
the ACK bit. The user can decide to retrieve the time tag or
not via dedicated SPI instructions (see Table 1).
FILTER AND MASK ID FORMAT
The HI-5110 allows filtering of up to 8 unique extended
frames with the first two data bytes. Filtering is enabled by
setting the FILTON bit in Control Register 1, CTRL1. It the
FILTON bit is not set, then filtering is globally disabled and all
CAN IDs are accepted.
TT
8
TT
1
TT
0
TT
5
TT
4
TT
3
TT
2
TT
7
TT
6
TT
15
TT
14
TT
13
TT
12
TT
11
TT
10
TT
9
x x
specific to Extended IDs should be written as zeros for
Standard IDs. The filter mechanism works by comparing the
filter ID to the CAN message ID. If the corresponding bit in
the mask ID is logic one, then the CAN ID bit must match the
filter ID for acceptance to occur. If a mask ID bit is logic zero,
then acceptance will occur regardless of the value of the
CAN ID bit. In this case, the filter bits are don’t care.
Following reset, all eight filter and mask registers should be
loaded before enabling the FILTON bit. Note that following
reset, filter and mask bits are not reset, therefore the
FILTON bit may be set to enable filtering using the pre-reset
mask and filter values.
READING THE RECEIVE BUFFERS VIA SPI
Table 1 summarizes the SPI instructions for reading the
receive buffers. The host has a choice of retrieving a
message with a 16-bit time tag or not. The receive data
format is shown in Table 5. The first data byte identifies
whether the frame was standard or extended format and the
FILHIT2:0 bits identify which filter passed the message;
<000> to <111>. If more than one filter passed the message,
the lowest value will be given priority and be identified by the
FILHIT2:0 bits. As can be seen in Table 5, bits specific to
extended frames will be read as zeros for standard frames.
If the received data does not contain an 8 byte payload (8
data bytes), the HI-5110 will pad the remaining data bytes
with zeros. The host should keep CS low for the duration of
the SPI sequence.
There is a specific SPI instruction for loading and reading
each filter and mask. The format is the same for both
standard and extended IDs and is shown in Table 4. Bits
HOLT INTEGRATED CIRCUITS
39
HI-5110
Temporary Receive Buffer
ID Acceptance Filter 0
ID Mask Filter 0
MESSTAT Register
FILHIT3:0 bits
Yes
FILHIT3:0 = 1000
Match ?
No
ID Acceptance Filter 1
ID Mask Filter 1
Match ?
Yes
FILHIT3:0 = 1001
No
........
........
Load Receive
FIFO
ID Acceptance Filter 7
ID Mask Filter 7
Match ?
Yes
FILHIT3:0 = 1111
No
Message not stored
Figure 13. Receive Buffer Structure
HOLT INTEGRATED CIRCUITS
40
HI-5110
Table 4. SPI Filter and Mask ID Format
a) Filter ID Format
Content
Bit Description (”x” = Don’t care)
1
ID28 to ID21
2
ID20 to ID18, RTR, IDE,
ID17 to ID15
(Note: ID17 to ID15 should be written
as zeros for Standard ID)
3
ID14 to ID7
(Note: Written as zeros for Standard ID)
4
ID6 to ID0
(Note: Written as zeros for Standard ID)
5
Data Byte 1
6
Data Byte 2
FI
D1
5
FI
D1
8
RT
R
ID
E
FI
D1
7
FI
D6
FI
D0
FI
FI
D7
D1
4
FI
D2
0
FI
FI
D2
1
D2
8
Byte
FD
FD
B0
B7
FD
FD
B0
B7
x
b) Mask ID Format
Content
Bit Description (”x” = Don’t care)
1
ID28 to ID21
2
ID20 to ID18, RTR, IDE,
ID17 to ID15
(Note: ID17 to ID15 should be written
as zeros for Standard ID)
3
ID14 to ID7
(Note: Written as zeros for Standard ID)
4
ID6 to ID0
(Note: Written as zeros for Standard ID)
5
Data Byte 1
6
Data Byte 2
MI
5
7
D1
D1
MI
MI
D1
RT 8
R
ID
E
MI
MI
D0
MI
MI
D6
B0
B0
MD
MD
B7
MD
B7
x
MD
HOLT INTEGRATED CIRCUITS
41
MI
D1
D7
4
MI
D2
0
MI
D2
D2
1
8
Byte
HI-5110
Table 5. SPI Receive Data Format
Time Tag Lower Byte
(Note: This byte only applies to time tag
SPI instructions; see Table 1)
4
ID28 to ID21
5
ID20 to ID18, SRR, IDE,
ID17 to ID15
(Note: SRR and ID17 to ID15 are
read as zeros for Std Frames)
6
ID14 to ID7
(Read as zeros for Std Frames)
7
ID6 to ID0, RTR
(Note: ID6 to ID0 are
read as zeros for Std Frames)
8
r0, r1, DLC3 to DLC0
(Note: r1 is read as zero for Std Frames)
9
Data Byte 1
21
15
17
ID
ID
ID
18
SR
R
ID
E
ID
ID
20
ID
ID
7
14
0
ID
ID
6
DL
C3
DL
C2
DL
C1
DL
C0
ID
r1
r0
Data Byte 3
12
Data Byte 4
13
Data Byte 5
14
Data Byte 6
15
Data Byte 7
16
Data Byte 8
DB
HOLT INTEGRATED CIRCUITS
42
0
11
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
DB
Data Byte 2
DB
DB
0
7
x x
7
10
TT
8
3
TT
1
TT
0
Time Tag Upper Byte
(Note: This byte only applies to time tag
SPI instructions; see Table 1)
28
2
x x x x
RT
R
Message Tag
(Note: This byte does not apply to the
Temporary Receive Buffer)
TT
5
TT
4
TT
3
TT
2
1
ID
E
FI
LH
I
FI T2
LH
I
FI T1
LH
IT
0
Bit Description (”x” = Don’t care)
TT
15
TT
14
TT
13
TT
12
TT
11
TT
10
TT
9
Content
TT
7
TT
6
Byte
HI-5110
TIMING DIAGRAMS
SERIAL INPUT TIMING DIAGRAM
t CPH
CS
tCHH
t SCKF
t CSS
t CSH
SCK
t DS
t DH
SI
t SCKR
MSB
LSB
SERIAL OUTPUT TIMING DIAGRAM
t CPH
CS
t SCKH
tSCKL
SCK
t CHZ
t DV
SO
Hi Impedance
MSB
HOLT INTEGRATED CIRCUITS
43
LSB
Hi Impedance
HI-5110
ABSOLUTE MAXIMUM RATINGS
(Voltages referenced to Gnd = 0V)
VDD:..........................................................................7V
VLOGIC:....................................................................7V
Operating Temperature Range: (Industrial).........................-40°C to +85°C
(Hi-Temp) ........................-55°C to +125°C
DC Voltages at CANH, CANL:.................................................-58V to +58V
DC Voltages at all other pins:.........................................-0.5V to VDD +0.5V
Maximum Junction Temperature ......................................................175°C
Supply Voltages,
1
Electrostatic Discharge (ESD) , pins CANH, CANL ........................+/- 6kV
all other pins
...............................................................................+/- 4kV
2
Storage Temperature Range:
-65°C to +150°C
Soldering Temperature:
(Plastic - leads).............10 sec. at +280°C
(Plastic - body) .....................+220°C Max.
NOTES:
1. Human Body Model (HBM).
2. Junction Temperature TJ is defined as TJ = TAMB + P × Rth, where TAMB is the ambient or operating temperature, P is the power dissipation and Rth is
a fixed thermal resistance value which depends on the package and circuit board mounting conditions.
Stresses above those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only. Functional
operation of the device at these or any other conditions above those indicated in the operational sections of the specifications is not implied. Exposure
to absolute maximum rating conditions for extended periods may affect device reliability.
HOLT INTEGRATED CIRCUITS
44
HI-5110
DC ELECTRICAL CHARACTERISTICS
VLOGIC = 3.3V or 5V, VDD = 5V. Operating temperature range (unless otherwise noted).
LIMITS
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNIT
Supply
Supply Voltage
VLOGIC
VDD
IDD1
IDD2
Supply Current
3.15
4.75
VLOGIC, fOSC = 24MHz, SO = Open
VDD, fOSC = 24MHz, SO = Open
5.25
5.25
10
20
V
V
mA
mA
0.2VLOGIC
V
V
Logic Inputs
High-Level Input Voltage
Low-Level Input Voltage
VIH
VIL
Input sink current
Input source current
Pull-up current (CS)
Pull-down current (SI, SCK, MR pins)
(TXEN)
IIH
IIL
IPU
IPD
IPD
VIH = VLOGIC
VIL = GND
VPU = VLOGIC
VPD = GND
VPD = GND
High-Level Output Voltage
Low-Level Output Voltage
VOH
VOL
IOH = -100μA
IOL = 1mA
0.9VLOGIC
Output sink current
Output source current
IOL
IOH
VOUT = 0.4V
VOUT = VDD - 0.4V
1.6
VO(CANH)
VO(CANL)
See Fig 14. RL = 60 Ω
3
0.5
Matching of dominant output voltage,
VCC − VCANH − VCANL
VOM
See Fig. 14. RL = 60 Ω
Dominant differential output voltage
Recessive differential output voltage
VDIFF(d)(o)
VDIFF(r)(o)
45 Ω < RL < 65 Ω, see Fig. 15
No Load
Recessive output voltage
VCANH(r),
VCANL(r)
No Load, see Fig. 14
VDIFF(d)(i)
VDIFF(r)(i)
VDIFF(hys)
− 12 V < VCANH, VCANL < + 12 V
− 12 V < VCANH, VCANL < + 12 V
− 12 V < VCANH, VCANL < + 12 V
See Fig. 18
0.9
ICANH, ICANL
VDD = 0 V (unpowered node)
− 200
IO(sc)
pin CANH, VCANH = -58 V
pin CANL, VCANL = +58 V
See Fig. 16
− 200
RIN(CM)
RIN(CM)(m)
− 12 V < VCANH, VCANL < + 12 V
VCANH = VCANL
15
−3
RIN(DIFF)
− 12 V < VCANH, VCANL < + 12 V
Vsplit
Normal Mode
See Fig. 17
0.8VLOGIC
1.5
-30
200
100
μA
μA
μA
μA
μA
0.1VLOGIC
V
V
-1
mA
mA
3.6
1.4
4.25
1.75
V
V
− 100
0
150
mV
1.5
− 50
0
3
50
V
mV
2
0.5VDD
3
V
0
70
0.5
V
V
mV
+ 200
μA
200
mA
mA
25
45
+3
kΩ
%
25
50
75
kΩ
2.4
2.5
2.6
V
-1.5
-200
30
15
Logic Outputs
Bus Lines (pins CANH, CANL)
CANH dominant output voltage
CANL dominant output voltage
Dominant differential input voltage (receiver)
Recessive differential input voltage (receiver)
Differential input hysteresis (receiver)
Input leakage current
Short circuit output current
Common mode input resistance
Deviation between common mode input resistance
Differential input resistance
SPLIT pin output voltage
Common mode input capacitance1 (1Mbit/s data rate)
Differential input capacitance1 (1Mbit/s data rate)
CIN(CM)
CDIFF(CM)
HOLT INTEGRATED CIRCUITS
45
20
10
pF
pF
HI-5110
AC ELECTRICAL CHARACTERISTICS
VLOGIC = 3.3V or 5V, VDD = 5V. Operating temperature range (unless otherwise noted).
LIMITS
PARAMETER
SYMBOL
UNITS
MIN
TYP
MAX
SPI Interface Timing
20
MHz
SCK clock frequency
fSCK
SCK clock period
tCYC
50
ns
CS active after last SCK rising edge
tCHH
5
ns
CS setup time to first SCK rising edge
tCSS
10
ns
CS hold time after last SCK falling edge
tCSH
25
ns
CS inactive between SPI instructions
tCPH
25
ns
SPI SI Data set-up time to SCK rising edge
tDS
5
ns
SPI SI Data hold time after SCK rising edge
tDH
5
ns
SCK rise time
tSCKR
2
ns
SCK fall ime
tSCKF
2
ns
SCK pulse width high
tSCKH
25
ns
SCK pulse width low
tSCKL
25
ns
SO valid after SCK falling edge
tDV
30
ns
SO high-impedance after SCK falling edge
tCHZ
25
ns
25
1000
μs
kHz
6
ms
CAN Bus Data Rate
Bit time
Bit rate
tBit
fBit
1
40
tdom(TXD)
0.3
Time Out
Permanent dominant time-out
HOLT INTEGRATED CIRCUITS
46
2
HI-5110
Internal
transceiver
VDIFF(d)(o)
RL
VO(CANH)
VO(CANL)
Dominant
Recessive
~3.5V: VO(CANH)
~2.5V
~1.5V: VO(CANL)
Figure 14. CAN Bus Driver Circuit
Internal
transceiver
300 W +/- 1%
CANH
0V
VDIFF(d)(o)
RL
+_
CANL
-12V <= VTEST <= +12V
300 W +/- 1%
Figure 15. CAN Bus Driver (Dominant) Test Circuit
Internal
transceiver
CANH
0V
+_
-58V or +58V
CANL
Figure 16. CAN Bus Driver Short-Circuit Test
HOLT INTEGRATED CIRCUITS
47
HI-5110
HI-5110
CANH
Rs = 60 W
SPLIT
Rs = 60 W
CANL
Figure 17. Split-Termination Connection
CANH
Internal
Transceiver
RXD
VDIFF(d)(i)
VDIFF(d)(i) = VI(CANH) + VI(CANL)
VI(CANL)
CANL
Figure 18. CAN Bus Receiver Common Mode Voltage Test
HI-5110
C1
OSCIN
R
Crystal
Resonator
OSCOUT
C2
R = 1.5 MW, C1 = C2 = 10pF typ.
Figure 19. Suggested Crystal Oscillator Circuit
HOLT INTEGRATED CIRCUITS
48
HI-5110
ADDITIONAL PACKAGE CONFIGURATIONS AND PINOUTS
VLOGIC 1
18 INT
VLOGIC 1
18 INT
OSCOUT 2
17 MR
OSCOUT 2
17 MR
OSCIN 3
16 CS
OSCIN 3
16 CS
15 SO
GP1 4
GP1 4
5111PSx
14 SI
GP2 5
13 SCK
TXEN 6
12 STAT
CLKOUT 7
RXD 8
11
TXD
GND 9
10 -
TXEN 6
CLKOUT 7
GND 8
CANL 9
44
43
42
41
40
39
38
37
36
35
34
5113PCx
33
32
31
30
29
28
27
26
25
24
23
CS
SO
SI
SCK
STAT
-
SPLIT
GND
GND
CANL
CANL
CANH
CANH
VDD
VDD
-
12
13
14
15
16
17
18
19
20
21
22
- 1
- 2
OSCI 3
GP1 4
- 5
GP2 6
TXEN 7
CLKOUT 8
- 9
- 10
- 11
14 SI
13 SCK
12 STAT
11
VDD
10 CANH
18-Pin Plastic SOIC - WB Package
OSCO
VLOGIC
INT
MR
-
18-Pin Plastic SOIC - WB Package
GP2 5
15 SO
5112PSx
44 Pin Plastic QFN, 7mm x 7mm
HOLT INTEGRATED CIRCUITS
49
HI-5110
ORDERING INFORMATION
HI - 511x xxx x
PART
NUMBER
Blank
LEAD
FINISH
Tin / Lead (Sn / Pb) Solder
100% Matte Tin (Pb-free, RoHS compliant)
F
PART
NUMBER
PACKAGE
DESCRIPTION
PSI
18 PIN PLASTIC WIDE BODY SOIC (18HW)
PCI
44 PIN PLASTIC QFN (44PCS) (HI-5113 only)
PART
NUMBER
DESCRIPTION
5110
Integrated transceiver with SPLIT pin option
5111
Digital-only option, no transceiver
5112
Integrated transceiver with CLKOUT pin option
5113
Integrated transceiver with both SPLIT & CLKOUT pin options
HOLT INTEGRATED CIRCUITS
50
PACKAGE DIMENSIONS
18-PIN PLASTIC SMALL OUTLINE (SOIC) - WB
(Wide Body)
.454 ± .008
(11.531 ± .20)
inches (millimeters)
Package Type: 18HW
.0105 ± .0015
(.2667 ± .038
.4065 ± .0125
(10.325 ± .32)
.292 ± .005
(7.417 ± .13)
See Detail A
.0165 ± .003
(.419 ± .09)
.090 ± .010
(2.286 ± .254)
0° to 8°
.050
BSC
(1.27)
.0075 ± .0035
(.191 ± .089)
.033 ± .017
(.838 ± .43)
BSC = “Basic Spacing between Centers”
is theoretical true position dimension and
has no tolerance. (JEDEC Standard 95)
44-PIN PLASTIC CHIP-SCALE PACKAGE
Detail A
inches (millimeters)
Package Type: 44PCS
.276
BSC
(7.00)
.203 ± .006
(5.15 ± .15)
.020 BSC
(0.50)
.276
BSC
(7.00)
.203 ± .006
(5.15 ± .15)
Top View
Bottom
View
.010
(0.25) typ
.039
max
(1.00)
.008 typ
(0.2)
Electrically isolated heat sink
pad on bottom of package.
Connect to any ground or
power plane for optimum
thermal dissipation.
BSC = “Basic Spacing between Centers”
is theoretical true position dimension and
has no tolerance. (JEDEC Standard 95)
HOLT INTEGRATED CIRCUITS
51
.016 ± .002
(0.40 ± .05)