TPS76901-Q1, TPS76912-Q1, TPS76915-Q1, TPS76918-Q1, TPS76925-Q1 TPS76927-Q1, TPS76928-Q1, TPS76930-Q1, TPS76933-Q1, TPS76950-Q1 ULTRALOW-POWER 100-mA LOW-DROPOUT LINEAR REGULATORS SGLS118A – DECEMBER 2001 – REVISED JANUARY 2002 D D D D D D D D D D DBV PACKAGE (TOP VIEW) Qualification in Accordance With AEC-Q100† Qualified for Automotive Applications 100-mA Low-Dropout Regulator Available in 1.2-V, 1.5-V, 1.8-V, 2.5-V, 2.7-V, 2.8-V, 3.0-V, 3.3-V, and 5-V Fixed-Output and Adjustable Versions Only 17 µA Quiescent Current at 100 mA 1 µA Quiescent Current in Standby Mode Dropout Voltage Typically 71 mV at 100 mA Over Current Limitation –40°C to 125°C Operating Junction Temperature Range 5-Pin SOT-23 (DBV) Package IN 1 GND 2 EN 3 5 OUT 4 NC/FB TPS76933 GROUND CURRENT vs FREE-AIR TEMPERATURE 22 21 VI = 4.3 V CO = 4.7 µF The TPS769xx-Q1 family of low-dropout (LDO) voltage regulators offers the benefits of low dropout voltage, ultralow-power operation, and miniaturized packaging. These regulators feature low dropout voltages and ultralow quiescent current compared to conventional LDO regulators. Offered in a 5-terminal small outline integrated-circuit SOT-23 package, the TPS769xx-Q1 series devices are ideal for micropower operations and where board space is at a premium. Ground Current – µ A description 20 19 IO = 100 mA 18 IO = 0 mA 17 16 A combination of new circuit design and process 15 innovation has enabled the usual PNP pass transistor –60 –40 –20 0 20 40 60 80 100 120 140 to be replaced by a PMOS pass element. Because the TA – Free-Air Temperature – °C PMOS pass element behaves as a low-value resistor, the dropout voltage is very low, typically 71 mV at 100 mA of load current (TPS76950-Q1), and is directly proportional to the load current. Since the PMOS pass element is a voltage-driven device, the quiescent current is ultralow (28 µA maximum) and is stable over the entire range of output load current (0 mA to 100 mA). The ultralow-dropout voltage feature and ultralow-power operation result in a significant increase in system battery operating life, making this device suitable for use in automotive applications. The TPS769xx-Q1 also features a logic-enabled sleep mode to shut down the regulator, reducing quiescent current to 1 µA typical at TJ = 25°C. The TPS769xx-Q1 is offered in 1.2-V, 1.5-V, 1.8-V, 2.5-V, 2.7-V, 2.8-V, 3.0-V, 3.3-V, and 5-V fixed-voltage versions and in a variable version (programmable over the range of 1.2 V to 5.5 V). † Contact factory for details. Q100 qualification data available on request. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Copyright 2002, Texas Instruments Incorporated PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1 TPS76901-Q1, TPS76912-Q1, TPS76915-Q1, TPS76918-Q1, TPS76925-Q1 TPS76927-Q1, TPS76928-Q1, TPS76930-Q1, TPS76933-Q1, TPS76950-Q1 ULTRALOW-POWER 100-mA LOW-DROPOUT LINEAR REGULATORS SGLS118A – DECEMBER 2001 – REVISED JANUARY 2002 AVAILABLE OPTIONS TJ VOLTAGE PACKAGE PART NUMBER SYMBOL Variable 1.2V to 5.5V TPS76901QDBVTQ1† TPS76901QDBVRQ1‡ PCFQ 1.2 V TPS76912QDBVTQ1† TPS76915QDBVTQ1† TPS76912QDBVRQ1‡ TPS76915QDBVRQ1‡ PCGQ TPS76918QDBVTQ1† TPS76925QDBVTQ1† TPS76918QDBVRQ1‡ TPS76925QDBVRQ1‡ TPS76927QDBVTQ1† TPS76928QDBVTQ1† TPS76927QDBVRQ1‡ TPS76928QDBVRQ1‡ PCKQ TPS76930QDBVRQ1‡ TPS76933QDBVRQ1‡ PCMQ 3.3 V TPS76930QDBVTQ1† TPS76933QDBVTQ1† 5.0 V TPS76950QDBVTQ1† TPS76950QDBVRQ1‡ PCOQ 1.5 V 1.8 V SOT-23 (DBV) 2.5 V –40°C to 125°C 2.7 V 2.8 V 3.0 V † The DBVT indicates tape and reel of 250 parts. ‡ The DBVR indicates tape and reel of 3000 parts. functional block diagram TPS76901-Q1 OUT IN EN Current Limit / Thermal Protection VREF FB GND TPS76912/15/18/25/27/28/30/33/50-Q1 OUT IN EN VREF Current Limit / Thermal Protection GND 2 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 PCHQ PCIQ PCJQ PCLQ PCNQ TPS76901-Q1, TPS76912-Q1, TPS76915-Q1, TPS76918-Q1, TPS76925-Q1 TPS76927-Q1, TPS76928-Q1, TPS76930-Q1, TPS76933-Q1, TPS76950-Q1 ULTRALOW-POWER 100-mA LOW-DROPOUT LINEAR REGULATORS SGLS118A – DECEMBER 2001 – REVISED JANUARY 2002 Terminal Functions TERMINAL NAME I/O NO. DESCRIPTION GND 2 Ground EN 3 I Enable input FB 4 I Feedback voltage (TPS76901-Q1 only) IN 1 I Input supply voltage NC 4 OUT 5 No connection (Fixed options only) O Regulated output voltage absolute maximum ratings over operating free-air temperature range (unless otherwise noted)Ĕ Input voltage range (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 0.3 V to 13.5 V Voltage range at EN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to VI + 0.3 V Voltage on OUT, FB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V Peak output current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Internally limited ESD rating, HBM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 kV Continuous total power dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Dissipation Rating Table Operating virtual junction temperature range, TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 40°C to 150°C Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 65°C to 150°C † Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTE 1: All voltage values are with respect to network ground terminal. DISSIPATION RATING TABLE BOARD PACKAGE RθJC RθJA DERATING FACTOR ABOVE TA = 25°C TA ≤ 25°C POWER RATING TA = 70°C POWER RATING TA = 85°C POWER RATING Low K‡ High K§ DBV 65.8 °C/W 259 °C/W 3.9 mW/°C 386 mW 212 mW 154 mW DBV 65.8 °C/W 180 °C/W 5.6 mW/°C 555 mW 305 mW 222 mW ‡ The JEDEC Low K (1s) board design used to derive this data was a 3 inch x 3 inch, two layer board with 2 ounce copper traces on top of the board. § The JEDEC High K (2s2p) board design used to derive this data was a 3 inch x 3 inch, multilayer board with 1 ounce internal power and ground planes and 2 ounce copper traces on top and bottom of the board. recommended operating conditions MIN NOM MAX UNIT Input voltage, VI (see Note 2) 2.7 10 V Output voltage range, VO 1.2 5.5 V 0 100 mA –40 125 °C Continuous output current, IO (see Note 3) Operating junction temperature, TJ NOTES: 2. To calculate the minimum input voltage for your maximum output current, use the following formula: VI(min) = VO(max) + VDO (max load) 3. Continuous output current and operating junction temperature are limited by internal protection circuitry, but it is not recommended that the device operate under conditions beyond those specified in this table for extended periods of time. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 3 TPS76901-Q1, TPS76912-Q1, TPS76915-Q1, TPS76918-Q1, TPS76925-Q1 TPS76927-Q1, TPS76928-Q1, TPS76930-Q1, TPS76933-Q1, TPS76950-Q1 ULTRALOW-POWER 100-mA LOW-DROPOUT LINEAR REGULATORS SGLS118A – DECEMBER 2001 – REVISED JANUARY 2002 electrical characteristics over recommended operating free-air temperature range, VI = VO(typ) + 1 V, IO = 100 mA, EN = 0 V, Co = 4.7 µF (unless otherwise noted) PARAMETER TEST CONDITIONS TPS76901 Q1 TPS76901-Q1 Output voltage g (10 ( µ µA to 100 mA load)) (see Note 4) 1.2 V ≤ VO ≤ 5.5 V, MIN TJ = 25°C TJ = –40°C to 125°C 1.2 V ≤ VO ≤ 5.5 V, TPS76912 Q1 TPS76912-Q1 TJ = 25°C, TJ = –40°C to 125°C, 2.7 V < VIN < 10 V TPS76915 Q1 TPS76915-Q1 TJ = 25°C, TJ = –40°C to 125°C, 2.7 V < VIN < 10 V TPS76918 Q1 TPS76918-Q1 TJ = 25°C, TJ = –40°C to 125°C, 2.8 V < VIN < 10 V TPS76925 Q1 TPS76925-Q1 TJ = 25°C, TJ = –40°C to 125°C, TPS76927 Q1 TPS76927-Q1 TJ = 25°C, TJ = –40°C to 125°C, 3.7 V < VIN < 10 V TPS76928 Q1 TPS76928-Q1 TJ = 25°C, TJ = –40°C to 125°C, 3.8 V < VIN < 10 V TPS76930 Q1 TPS76930-Q1 TJ = 25°C, TJ = –40°C to 125°C, 4.0 V < VIN < 10 V TPS76933 Q1 TPS76933-Q1 TJ = 25°C, TJ = –40°C to 125°C, TPS76950 Q1 TPS76950-Q1 TJ = 25°C, TJ = –40°C to 125°C, 6.0 V < VIN < 10 V EN = 0V, TJ = 25°C 0 mA < IO < 100 mA, EN = 0V, TJ = –40°C to 125°C IO = 100 mA, EN = 0V, TJ = 25°C IO = 0 to 100 mA, Quiescent current ((GND current)) (see Notes 4 and 5) Load regulation Output voltage line regulation (∆VO/VO) (see Note 5) 2.7 V < VIN < 10 V 2.7 V < VIN < 10 V Output current limit 1.5 1.545 1.8 1.854 2.5 2.575 2.7 2.619 2.8 2.716 2.884 3.0 2.910 4.3 V < VIN < 10 V 3.201 3.090 3.3 3.399 5.0 4.850 5.150 17 µA 28 12 mV 0.04 %/V 0.1 µVrms 190 See Note 4 2.7 < VI < 10 V V 2.781 VO + 1 V < VI ≤ 10 V, TJ = –40°C to 125°C, See Note 4 VO = 0 V, EN = VI, Standby current 1.261 1.455 4.0 V < VIN < 10 V 4.3 V < VIN < 10 V VO + 1 V < VI ≤ 10 V, TJ = 25°C, See Note 4 1.03VO 1.187 2.425 6.0 V < VIN < 10 V UNIT 1.224 3.5 V < VIN < 10 V BW = 300 Hz to 50 kHz, Co = 10 µF, TJ = 25°C Output noise voltage 0.97VO 1.746 3.8 V < VIN < 10 V MAX VO 2.8 V < VIN < 10 V 3.5 V < VIN < 10 V 3.7 V < VIN < 10 V TYP 350 1 750 mA µA TJ = –40°C to 125°C 2 µA NOTES: 4. Minimum IN operating voltage is 2.7 V or VO(typ) + 1 V, whichever is greater. Maximum IN voltage 10 V, minimum output current 10 µA, maximum output current 100 mA. 5. If VO ≤ 1.8 V then VImin = 2.7 V, VImax = 10 V: Line Reg. (mV) + ǒ%ńVǓ V O If VO ≥ 2.5 V then VImin = VO + 1 V, VImax = 10 V: Line Reg. (mV) 4 + ǒ%ńVǓ V O ǒ V ǒ V POST OFFICE BOX 655303 Ǔ * 2.7 V Imax 100 Imax * ǒ V O 1000 ǓǓ )1 V 100 • DALLAS, TEXAS 75265 1000 TPS76901-Q1, TPS76912-Q1, TPS76915-Q1, TPS76918-Q1, TPS76925-Q1 TPS76927-Q1, TPS76928-Q1, TPS76930-Q1, TPS76933-Q1, TPS76950-Q1 ULTRALOW-POWER 100-mA LOW-DROPOUT LINEAR REGULATORS SGLS118A – DECEMBER 2001 – REVISED JANUARY 2002 electrical characteristics over recommended operating free-air temperature range, VI = VO(typ) + 1 V, IO = 100 mA, EN = 0 V, Co = 4.7 µF (unless otherwise noted) (continued) PARAMETER TEST CONDITIONS MIN FB input current FB = 1.224 V (TPS76901-Q1) –1 High level enable input voltage 2.7 V < VI < 10 V 1.7 Low level enable input voltage 2.7 V < VI < 10 V Power supply ripple rejection f = 1 kHz, TJ = 25°C, Co = 10 µF, See Note 4 TPS76930 Q1 TPS76930-Q1 Dropout voltage (see Note 6) TPS76933 Q1 TPS76933-Q1 TPS76950 Q1 TPS76950-Q1 UNIT µA 1 V V 60 –1 EN = VI TPS76928 Q1 TPS76928-Q1 MAX 0.9 EN = 0 V Input current (EN) TYP 0 –1 IO = 50 mA, IO = 50 mA, TJ = 25°C TJ = –40°C to 125°C 60 IO = 100 mA, IO = 100 mA, TJ = 25°C TJ = –40°C to 125°C 122 IO = 50 mA, IO = 50 mA, TJ = 25°C TJ = –40°C to 125°C 57 IO = 100 mA, IO = 100 mA, TJ = 25°C TJ = –40°C to 125°C 115 IO = 50 mA, IO = 50 mA, TJ = 25°C TJ = –40°C to 125°C 48 IO = 100 mA, IO = 100 mA, TJ = 25°C TJ = –40°C to 125°C 98 IO = 50 mA, IO = 50 mA, TJ = 25°C TJ = –40°C to 125°C 35 IO = 100 mA, IO = 100 mA, TJ = 25°C TJ = –40°C to 125°C 71 dB 1 µA 1 µA 125 245 115 230 mV 100 200 85 170 NOTES: 4. Minimum IN operating voltage is 2.7 V or VO(typ) + 1 V, whichever is greater. Maximum IN voltage 10 V, minimum output current 10 µA, maximum output current 100 mA. 6. IN voltage equals VO(Typ) – 100mV; TPS76901-Q1 output voltage set to 3.3V nominal with external resistor divider. TPS76912-Q1, TPS76915-Q1, TPS76918-Q1, TPS76925-Q1, and TPS76927-Q1 dropout voltage limited by input voltage range limitations. TY PICAL CHARACTERISTICS Table of Graphs FIGURE VO Zo VDO vs Output current 1, 2, 3 vs Free-air temperature 4, 5, 6 Ground current vs Free-air temperature 7 Output spectral noise density vs Frequency 8 Output impedance vs Frequency 9 Dropout voltage vs Free-air temperature 10 Ripple rejection vs Frequency 11 Output voltage LDO startup time 12 Line transient response 13, 15 Load transient response 14, 16 Equivalent series resistance (ESR) POST OFFICE BOX 655303 vs Output current 17, 19 vs Added ceramic capacitance 18, 20 • DALLAS, TEXAS 75265 5 TPS76901-Q1, TPS76912-Q1, TPS76915-Q1, TPS76918-Q1, TPS76925-Q1 TPS76927-Q1, TPS76928-Q1, TPS76930-Q1, TPS76933-Q1, TPS76950-Q1 ULTRALOW-POWER 100-mA LOW-DROPOUT LINEAR REGULATORS SGLS118A – DECEMBER 2001 – REVISED JANUARY 2002 TYPICAL CHARACTERISTICS TPS76925 TPS76915 OUTPUT VOLTAGE vs OUTPUT CURRENT OUTPUT VOLTAGE vs OUTPUT CURRENT 1.498 2.498 VI = 3.5 V CO = 4.7 µF TA = 25° C 2.496 1.496 VO – Output Voltage – V 2.494 VO – Output Voltage – V VI = 2.7 V CO = 4.7 µF TA = 25° C 2.492 2.490 2.488 2.486 1.494 1.492 1.490 1.488 1.486 2.484 1.484 2.482 0 20 40 60 80 0 100 20 40 60 Figure 1 TPS76933 TPS76915 OUTPUT VOLTAGE vs OUTPUT CURRENT OUTPUT VOLTAGE vs FREE-AIR TEMPERATURE 1.496 VI = 4.3 V CO = 4.7 µF TA = 25° C 3.282 1.494 IO = 1 mA VI = 2.7 V CO = 4.7 µF 1.492 3.280 VO – Output Voltage – V VO – Output Voltage – V 100 Figure 2 3.284 3.278 3.276 3.274 3.272 1.490 1.488 1.486 IO = 100 mA 1.484 1.482 3.270 0 20 40 60 80 100 1.480 –60 –40 –20 0 20 40 Figure 3 Figure 4 POST OFFICE BOX 655303 60 80 100 120 140 TA – Free-Air Temperature – °C IO – Output Current – mA 6 80 IO – Output Current – mA IO – Output Current – mA • DALLAS, TEXAS 75265 TPS76901-Q1, TPS76912-Q1, TPS76915-Q1, TPS76918-Q1, TPS76925-Q1 TPS76927-Q1, TPS76928-Q1, TPS76930-Q1, TPS76933-Q1, TPS76950-Q1 ULTRALOW-POWER 100-mA LOW-DROPOUT LINEAR REGULATORS SGLS118A – DECEMBER 2001 – REVISED JANUARY 2002 TYPICAL CHARACTERISTICS TPS76925 TPS76933 OUTPUT VOLTAGE vs FREE-AIR TEMPERATURE OUTPUT VOLTAGE vs FREE-AIR TEMPERATURE 2.496 3.285 2.494 IO = 1 mA VO – Output Voltage – V VO – Output Voltage – V 2.490 2.488 2.486 2.484 IO = 100 mA 2.482 2.480 2.476 –60 –40 –20 0 20 40 60 VI = 4.3 V CO = 4.7 µF 3.275 3.270 IO = 100 mA 3.265 3.260 VI = 3.5 V CO = 4.7 µF 2.478 IO = 1 mA 3.280 2.492 3.255 –60 –40 –20 80 100 120 140 TA – Free-Air Temperature – °C Figure 5 TPS76933 40 60 80 100 120 140 TPS76933 OUTPUT SPECTRAL NOISE DENSITY vs FREQUENCY 22 2 VI = 4.3 V CO = 4.7 µF Output Spectral Noise Density – µV Hz Ground Current – µ A 20 Figure 6 GROUND CURRENT vs FREE-AIR TEMPERATURE 21 0 TA – Free-Air Temperature – °C 20 IO = 100 mA 19 18 IO = 0 mA 17 16 15 –60 –40 –20 0 20 40 60 80 100 120 140 1.8 CO = 10 µF IO = 1 mA 1.6 CO = 4.7 µF IO = 100 mA 1.4 1.2 1 0.8 CO = 4.7 µF IO = 1 mA 0.6 0.4 0.2 VI = 4.3 V 0 100 TA – Free-Air Temperature – °C CO = 10 µF IO = 100 mA 1k 10k f – Frequency – Hz 100k Figure 8 Figure 7 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 7 TPS76901-Q1, TPS76912-Q1, TPS76915-Q1, TPS76918-Q1, TPS76925-Q1 TPS76927-Q1, TPS76928-Q1, TPS76930-Q1, TPS76933-Q1, TPS76950-Q1 ULTRALOW-POWER 100-mA LOW-DROPOUT LINEAR REGULATORS SGLS118A – DECEMBER 2001 – REVISED JANUARY 2002 TYPICAL CHARACTERISTICS TPS76933 OUTPUT IMPEDANCE vs FREQUENCY DROPOUT VOLTAGE vs FREE-AIR TEMPERATURE 2 Zo – Output Impedance – Ω 1.6 VI = 3.2 V CO = 4.7 µF VDO – Dropout Voltage – mV 1.8 1000 VI = 4.3 V CO = 4.7 µF ESR = 0.3 Ω TA = 25° C 1.4 1.2 1 0.8 IO = 1 mA 0.6 0.4 IO = 100 mA 10 IO = 10 mA IO = 100 mA 0.2 0 10 100 100 1k 10 k 100 k 1M 1 –60 –40 –20 0 20 40 60 80 100 120 140 TA – Free-Air Temperature – °C f – Frequency – Hz Figure 9 Figure 10 TPS76933 RIPPLE REJECTION vs FREQUENCY 100 LDO STARTUP TIME 90 Ripple Rejection – dB 80 EN 70 IO = 1 mA 60 50 40 30 IO = 100 mA 20 10 0 – 10 10 VI = 4.3 V CO = 4.7 µF ESR = 0.3 Ω 100 VO 1k 10 k 100 k 1M 10 M 0 20 f – Frequency – Hz 60 80 100 120 140 160 180 200 t – Time – µs Figure 12 Figure 11 8 40 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 TPS76901-Q1, TPS76912-Q1, TPS76915-Q1, TPS76918-Q1, TPS76925-Q1 TPS76927-Q1, TPS76928-Q1, TPS76930-Q1, TPS76933-Q1, TPS76950-Q1 ULTRALOW-POWER 100-mA LOW-DROPOUT LINEAR REGULATORS SGLS118A – DECEMBER 2001 – REVISED JANUARY 2002 10 0 –10 3.7 VI – Input Voltage – V TPS76915 LOAD TRANSIENT RESPONSE Current Load – mA TPS76915 LINE TRANSIENT RESPONSE 2.7 IL = 10 mA CO = 4.7 µF ESR = 0.3 Ω 0 20 40 60 100 0 ∆ VO – Change In Output Voltage – mV VO – Output Voltage – mV TYPICAL CHARACTERISTICS 0 –200 VI = 2.7 V CO = 10 µF ESR = 0.3 Ω –400 0 80 100 120 140 160 180 200 t – Time – µs 20 40 10 0 –10 ∆ VO – Change In Output Voltage – mV 5.3 VI – Input Voltage – V TPS76933 LOAD TRANSIENT RESPONSE Current Load – mA VO – Output Voltage – mV TPS76933 LINE TRANSIENT RESPONSE 4.3 IL = 10 mA CO = 4.7 µF ESR = 0.3 Ω 20 40 60 80 100 120 140 160 180 200 t – Time – µs Figure 14 Figure 13 0 60 80 100 120 140 160 180 t – Time – µs 100 0 VI = 4.3 V CO = 4.7 µF ESR = 0.3 Ω 100 0 –100 0 20 40 60 80 100 120 140 160 180 t – Time – µs Figure 16 Figure 15 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 9 TPS76901-Q1, TPS76912-Q1, TPS76915-Q1, TPS76918-Q1, TPS76925-Q1 TPS76927-Q1, TPS76928-Q1, TPS76930-Q1, TPS76933-Q1, TPS76950-Q1 ULTRALOW-POWER 100-mA LOW-DROPOUT LINEAR REGULATORS SGLS118A – DECEMBER 2001 – REVISED JANUARY 2002 TYPICAL CHARACTERISTICS TPS76933 TYPICAL REGIONS OF STABILITY TPS76933 TYPICAL REGIONS OF STABILITY EQUIVALENT SERIES RESISTANCE (ESR)† vs OUTPUT CURRENT EQUIVALENT SERIES RESISTANCE (ESR) vs ADDED CERAMIC CAPACITANCE 100 VIN = 4.3 V CO = 4.7 µF 3.3 V LDO Region of Instability 10 Region of Stability 1 0.1 ESR – Equivalent Series Resistance – Ω ESR – Equivalent Series Resistance – Ω 100 VIN = 4.3 V CO = 4.7 µF IL = 100 mA Region of Instability 10 Region of Stability 1 0 25 50 75 0 100 0.1 0.9 1 Figure 18 Figure 17 TPS76933 TYPICAL REGIONS OF STABILITY TPS76933 TYPICAL REGIONS OF STABILITY EQUIVALENT SERIES RESISTANCE (ESR)† vs OUTPUT CURRENT EQUIVALENT SERIES RESISTANCE (ESR) vs ADDED CERAMIC CAPACITANCE 100 100 VIN = 4.3 V CO = 10 µF 3.3 V LDO ESR – Equivalent Series Resistance – Ω ESR – Equivalent Series Resistance – Ω 0.6 0.7 0.8 Added Ceramic Capacitance – µF IO – Output Current – mA Region of Instability 10 1 Region of Stability 0.1 VIN = 4.3 V CO = 10 µF IL = 100 mA Region of Instability 10 Region of Stability 1 0 25 50 75 100 0 0.1 0.2 0.3 0.4 0.5 Figure 20 Figure 19 POST OFFICE BOX 655303 0.6 0.7 0.8 Added Ceramic Capacitance – µF IO – Output Current – mA 10 0.2 0.3 0.4 0.5 • DALLAS, TEXAS 75265 0.9 1 TPS76901-Q1, TPS76912-Q1, TPS76915-Q1, TPS76918-Q1, TPS76925-Q1 TPS76927-Q1, TPS76928-Q1, TPS76930-Q1, TPS76933-Q1, TPS76950-Q1 ULTRALOW-POWER 100-mA LOW-DROPOUT LINEAR REGULATORS SGLS118A – DECEMBER 2001 – REVISED JANUARY 2002 APPLICATION INFORMATION The TPS769xx family of low-dropout (LDO) regulators have been optimized for use in battery-operated equipment and automotive applications. They feature extremely low dropout voltages, low quiescent current (17 µA nominally), and enable inputs to reduce supply currents to 1 µA when the regulators are turned off. device operation The TPS769xx uses a PMOS pass element to dramatically reduce both dropout voltage and supply current over more conventional PNP-pass-element LDO designs. The PMOS pass element is a voltage-controlled device and, unlike a PNP transistor, it does not require increased drive current as output current increases. Supply current in the TPS769xx is essentially constant from no load to maximum load. Current limiting and thermal protection prevent damage by excessive output current and/or power dissipation. The device switches into a constant-current mode at approximately 350 mA; further load reduces the output voltage instead of increasing the output current. The thermal protection shuts the regulator off if the junction temperature rises above approximately 165°C. Recovery is automatic when the junction temperature drops approximately 25°C below the high temperature trip point. The PMOS pass element includes a back gate diode that conducts reverse current when the input voltage level drops below the output voltage level. A voltage of 1.7 V or greater on the EN input will disable the TPS769xx internal circuitry, reducing the supply current to 1µA. A voltage of less than 0.9 V on the EN input will enable the TPS769xx and will enable normal operation to resume. The EN input does not include any deliberate hysteresis, and it exhibits an actual switching threshold of approximately 1.5 V. A typical application circuit is shown in Figure 21. TPS769xx† VI C1 1 µF 1 IN NC/FB OUT 4 5 VO 3 EN + GND 2 4.7 µF ESR = 0.2 Ω † TPS76912, TPS76915, TPS76918, TPS76925, TPS76927, TPS76928, TPS76930, TPS76933, TPS76950 (fixed-voltage options). Figure 21. Typical Application Circuit POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 11 TPS76901-Q1, TPS76912-Q1, TPS76915-Q1, TPS76918-Q1, TPS76925-Q1 TPS76927-Q1, TPS76928-Q1, TPS76930-Q1, TPS76933-Q1, TPS76950-Q1 ULTRALOW-POWER 100-mA LOW-DROPOUT LINEAR REGULATORS SGLS118A – DECEMBER 2001 – REVISED JANUARY 2002 APPLICATION INFORMATION external capacitor requirements Although not required, a 0.047-µF or larger ceramic input bypass capacitor, connected between IN and GND and located close to the TPS769xx, is recommended to improve transient response and noise rejection. A higher-value electrolytic input capacitor may be necessary if large, fast-rise-time load transients are anticipated and the device is located several inches from the power source. Like all low dropout regulators, the TPS769xx requires an output capacitor connected between OUT and GND to stabilize the internal control loop. The minimum recommended capacitance is 4.7 µF. The ESR (equivalent series resistance) of the capacitor should be between 0.2 Ω and 10 Ω. to ensure stability. Capacitor values larger than 4.7 µF are acceptable, and allow the use of smaller ESR values. Capacitances less than 4.7 µF are not recommended because they require careful selection of ESR to ensure stability. Solid tantalum electrolytic, aluminum electrolytic, and multilayer ceramic capacitors are all suitable, provided they meet the requirements described above. Most of the commercially available 4.7 µF surface-mount solid tantalum capacitors, including devices from Sprague, Kemet, and Nichico, meet the ESR requirements stated above. Multilayer ceramic capacitors may have very small equivalent series resistances and may thus require the addition of a low value series resistor to ensure stability. CAPACITOR SELECTION PART NO. MAX ESR† SIZE (H × L × W)† MFR. VALUE T494B475K016AS KEMET 4.7 µF 1.5 Ω 1.9 × 3.5 × 2.8 195D106x0016x2T SPRAGUE 10 µF 1.5 Ω 1.3 × 7.0 × 2.7 695D106x003562T SPRAGUE 10 µF 1.3 Ω 2.5 × 7.6 × 2.5 AVX 4.7 µF 0.6 Ω 2.6 × 6.0 × 3.2 TPSC475K035R0600 † Size is in mm. ESR is maximum resistance in Ohms at 100 kHz and TA = 25°C. Contact manufacturer for minimum ESR values. 12 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 TPS76901-Q1, TPS76912-Q1, TPS76915-Q1, TPS76918-Q1, TPS76925-Q1 TPS76927-Q1, TPS76928-Q1, TPS76930-Q1, TPS76933-Q1, TPS76950-Q1 ULTRALOW-POWER 100-mA LOW-DROPOUT LINEAR REGULATORS SGLS118A – DECEMBER 2001 – REVISED JANUARY 2002 APPLICATION INFORMATION output voltage programming The output voltage of the TPS76901 adjustable regulator is programmed using an external resistor divider as shown in Figure 22. The output voltage is calculated using: V O ǒ) Ǔ + Vref 1 R1 R2 (1) Where: Vref = 1.224 V typ (the internal reference voltage) Resistors R1 and R2 should be chosen for approximately 7-µA divider current. Lower value resistors can be used but offer no inherent advantage and waste more power. Higher values should be avoided as leakage currents at FB increase the output voltage error. The recommended design procedure is to choose R2 = 169 kΩ to set the divider current at 7 µA and then calculate R1 using: R1 + ǒ Ǔ V V O ref *1 (2) R2 OUTPUT VOLTAGE PROGRAMMING GUIDE OUTPUT VOLTAGE (V) 2.5 TPS76901 DIVIDER RESISTANCE (kΩ)‡ R1 R2 174 169 3.3 287 169 3.6 324 169 4.0 383 169 5.0 523 169 VI 1 µF 1 IN OUT ≥ 1.7 V 3 VO R1 EN ≤ 0.9 V FB GND 2 ‡ 1% values shown. 5 4 4.7 µF R2 ESR = 0.2 Ω Figure 22. TPS76901 Adjustable LDO Regulator Programming POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 13 TPS76901-Q1, TPS76912-Q1, TPS76915-Q1, TPS76918-Q1, TPS76925-Q1 TPS76927-Q1, TPS76928-Q1, TPS76930-Q1, TPS76933-Q1, TPS76950-Q1 ULTRALOW-POWER 100-mA LOW-DROPOUT LINEAR REGULATORS SGLS118A – DECEMBER 2001 – REVISED JANUARY 2002 APPLICATION INFORMATION power dissipation and junction temperature Specified regulator operation is assured to a junction temperature of 125°C; the maximum junction temperature should be restricted to 125°C under normal operating conditions. This restriction limits the power dissipation the regulator can handle in any given application. To ensure the junction temperature is within acceptable limits, calculate the maximum allowable dissipation, PD(max), and the actual dissipation, PD, which must be less than or equal to PD(max). The maximum-power-dissipation limit is determined using the following equation: P T max * T J A + D(max) R qJA Where: TJmax is the maximum allowable junction temperature RθJA is the thermal resistance junction-to-ambient for the package, see the dissipation rating table. TA is the ambient temperature. ǒ Ǔ The regulator dissipation is calculated using: P D + VI * VO I O Power dissipation resulting from quiescent current is negligible. Excessive power dissipation will trigger the thermal protection circuit. regulator protection The TPS769xx PMOS-pass transistor has a built-in back diode that conducts reverse current when the input voltage drops below the output voltage (e.g., during power down). Current is conducted from the output to the input and is not internally limited. If extended reverse voltage operation is anticipated, external limiting might be appropriate. The TPS769xx features internal current limiting and thermal protection. During normal operation, the TPS769xx limits output current to approximately 350 mA. When current limiting engages, the output voltage scales back linearly until the overcurrent condition ends. While current limiting is designed to prevent gross device failure, care should be taken not to exceed the power dissipation ratings of the package. If the temperature of the device exceeds approximately 165°C, thermal-protection circuitry shuts it down. Once the device has cooled down to below approximately 140°C, regulator operation resumes. 14 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 TPS76901-Q1, TPS76912-Q1, TPS76915-Q1, TPS76918-Q1, TPS76925-Q1 TPS76927-Q1, TPS76928-Q1, TPS76930-Q1, TPS76933-Q1, TPS76950-Q1 ULTRALOW-POWER 100-mA LOW-DROPOUT LINEAR REGULATORS SGLS118A – DECEMBER 2001 – REVISED JANUARY 2002 MECHANICAL DATA DBV (R-PDSO-G5) PLASTIC SMALL-OUTLINE 0,50 0,30 0,95 5 0,20 M 4 1,70 1,50 1 0,15 NOM 3,00 2,60 3 Gage Plane 3,00 2,80 0,25 0°–8° 0,55 0,35 Seating Plane 1,45 0,95 0,05 MIN 0,10 4073253-4/F 10/00 NOTES: A. B. C. D. All linear dimensions are in millimeters. This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion. Falls within JEDEC MO-178 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 15 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third–party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Mailing Address: Texas Instruments Post Office Box 655303 Dallas, Texas 75265 Copyright 2002, Texas Instruments Incorporated