www.make-ps.com E-mail:[email protected] Single & Dual Output DC/DC Converter Series FKC12 FEATURES: ● ● ● ● ● ● ● ● 12Watt | DC-DC Converter 12W DIL PACKAGE 2:1 WIDE INPUT RANGE 100% BURNED IN HIGH EFFICIENCY UL94V-0 PACKAGE MATERIAL CUSTOM SOLUTIONS AVAILABLE RoHS COMPLIANT Remote Control:On/Off APPLICATIONS: ● Wireless Network ● Telecom/Datacom ● Industry Control System ● Measurement Equipment ● Semiconductor Equipment MODEL SELECTION CHART Output Current Efficiency Full Load (mA TYP) Output Voltage Vdc Full Load (mA) %TYP 1203 1220 1205 1205 1205 1205 1205 602 610 602 602 602 602 301 305 301 301 301 301 301 301 3.3 5 12 15 ±5 ±12 ±15 3.3 5 12 15 ±5 ±12 ±15 3.3 5 12 15 ±5 ±12 ±15 3500 2400 1000 800 ±1200 ±500 ±400 3500 2400 1000 800 ±1200 ±500 ±400 3500 2400 1000 800 ±1200 ±500 ±400 80 82 83 83 83 83 83 80 82 83 83 83 83 83 80 82 83 83 83 83 83 Input Current Part Number Input Voltage Vdc No-Load (mA TYP) FKC12-12S03 FKC12-12S05 FKC12-12S12 FKC12-12S15 FKC12-12D05 FKC12-12D12 FKC12-12D15 FKC12-24S03 FKC12-24S05 FKC12-24S12 FKC12-24S15 FKC12-24D05 FKC12-24D12 FKC12-24D15 FKC12-24S03 FKC12-24S05 FKC12-48S12 FKC12-48S15 FKC12-48D05 FKC12-48D12 FKC12-48D15 9-18 9-18 9-18 9-18 9-18 9-18 9-18 18-36 18-36 18-36 18-36 18-36 18-36 18-36 18-36 36-75 36-75 36-75 36-75 36-75 36-75 30 30 30 30 30 30 30 30 30 30 30 30 30 30 20 20 20 20 20 20 20 FKC12-12S03/*** add Suffix SMD for SMD package NOTE: All specifications in this datasheet are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. Temperature Derating Graph Tolerance Envelope Graph Tolerance Envelope 100 1/3 120% 110% 9 0% Output Current(%) Ambient Temperature(℃) 100% 80 % 70% 85 100 60% 75 70 % 4 0% -40 80 % 10% 0 90 % 50% Nature Convection 1 00% 30 % 50 1 10% 20% 75 25 Graph 1 20% Output Voltage(%) OutPut Power(%) Temperature Derating Graph www.make-ps.com E-mail:[email protected] Input Specifications Parameters Conditions Voltage Types Filter Protection Min Typ Max Units Typ Max Units 2:1 Pi Network Fuse Recommended Output Specifications Parameters Voltage Tolerance Short Circuit/ Restart Over Load Protection Line Regulation Load Regulation Minimum Load Ripple & Noise Transient response setting time Temperature Coefficinet:±0.05%/℃ Conditions BW=DC To 20MHz (with 1uF Cap.) current change from 25% to 100% Parameters ±2 % ±0.5 ±0.5 % % % 100 350 mVp-p us 150 High Line to Low Line Single & Dual (F.L-25%F.L) 10% of Full Load General Specifications Isolation Resistance Switching Frequency Operating Temperature Humidity Cooling Case material Weight Dimensions Potting Material Radiated Emissions Conducted Emissions Efficiency Isolation Voltage MTBF Storage Temperature Case Temperature Min Single/Dual Continuous/ Automatic Conditions 500Vdc Min 1000 Typ 400 -40 Non Condensing Free air Convection Max Units MΩ KHz ℃ % 100 95 Five-Side Shielded Case Appearance size EN55022 EN55022 80 For 10 seconds MIL-HDBK-217F @25℃ , Ground Benign 17.5 31.6X20.1X10.0 Epoxy (UL94V-0 rated) CLASS A CLASS A g mm % VDC Hours ℃ ℃ 1500 900000 -55 +125 +95 Suggest adding input external filter(C1,C2,L)to meet conducted emissions (En55022 class A) 12uH +Vin L C1 DC/DC Converter C2 2.2uF/100V +Vout 2.2uF/100V Load -Vout -Vin Recommended Test Circuit Vin +Vout Cin Single Cout GND Vin 100uF/25V -Vout 12V & 24V & 48V:Cin 100uF,100V 100uF/25V Cin GND Dual Cout Cout 100uF/25V 24V & 48V:Cin 100uF,100V 2/3 +Vout COM -Vout www.make-ps.com E-mail:[email protected] OUTLINE DRAWING Package Style and Pinning (mm) 31.80 20.30 10.20 3.8 2 5.10 20.30 2.54 DIP24 Package Style 15.20 Pin Connections Pin # 1 2 3 9 11 14 16 22 23 0.25 x 0.50 Rectangular Pin 9 11 16 14 1 2 3 Bottom View 23 22 Single ON/OFF -Vin -Vin NC NC +Vout -Vout +Vin +Vin Dual ON/OFF -Vin -Vin Com -Vout +Vout Com +Vin +Vin NC = No Connection Pin Pitch Tolerance ±0.35 mm SMD Package Style 32.00 20.30 31.40 SMD Package Style 11.20 2.54 Same spec. as the original DIP spec. and pin definition, excl. of the SMD type pin. 10.90 3.81 21.30 6.35 Pin Connections 25.40 Pin area 0.1 x 0.50 2.54 0.50 1.60 2.40 9 10 11 12 1 2 3 4 5 23.40 Bottom View 26.54 24.14 24 23 22 21 20 11 x 2.54 16 15 14 13 Top View 1 Pin # Single 1 ON/OFF 2 -Vin 3 -Vin 9 NC 11 NC 14 +Vout 16 -Vout 22 +Vin 23 +Vin Others NC NC = No Connection Dual ON/OFF -Vin -Vin Com -Vout +Vout Com +Vin +Vin NC Pin Pitch Tolerance ±0.35 mm 27.94 All specifications are typical at nominal input, nominal load and 25° C unless otherwise specified. External, low ESR, 10 microfarad (minimum) capacitor across output is recommended for operation. Make Power world-class design, development and manufacturing team stands ready to work with you to deliver the exact power converter you need for your ready to work with you to deliver the exact power converter you need for your demanding, large volume, OEM applications. And ... we ll do it on time and within budget Our experienced applications and design staffs; quick-turn prototype capability; highly automated, SMT assembly facilities; and in-line SPC quality-control techniques combine to give us the unique ability to design and deliver any quantity of power converters to the highest standards of quality and reliability. We have compiled a large library of DC/DC designs that are currently used in a variety of telecom, medical, computer, railway, aerospace and industrial applications. We may already have the converter you need. Contact us. Our goal is to provide you the highest-quality, most cost-effective power converters available. CUSTOM CAPABILITIES 3/3