Very Long Haul Gigabit Ethernet SFP Transceivers with Digital Diagnostics TRPAG1VXIxMS Product Description The TRPAG1VXIxMS SFP fiber optic transceivers with integrated digital diagnostics monitoring functionality offer a quick and reliable interface for Gigabit Ethernet applications. The diagnostic functions, alarm and warning features as described in the Multi-Source Agreement (MSA) document, SFF-8472 (Rev. 9.3), are provided via an I2C serial interface. The transceivers use a high power 1550nm DFB laser and an ultra high sensitivity Avalanche Photodiode (APD) receiver to provide a minimum optical link budget of 32dB, corresponding to a transmission distance of around 120km of single mode fiber (assuming a total connector and splice loss of 2dB, total system penalty of 3dB and fiber loss of 0.22dB/km). The transceivers satisfy Class I Laser Safety requirements in accordance with the U.S. FDA/CDRH and international IEC-60825 standards. The TRPAG1VXIxMS transceivers connect to standard 20-pad SFP connectors for hot plug capability. This allows the system designer to make configuration changes or maintenance by simply plugging in different types of transceivers without removing the power supply from the host system. Features Compatible with SFP MSA The transceivers have colored bail-type latches, which offer an easy and convenient way to release the modules. The latch is compliant with the SFP MSA. Internal Calibration for Digital Diagnostics The transmitter and receiver DATA interfaces are AC-coupled internally. LVTTL Transmitter Disable control input and Loss of Signal output interfaces are also provided. The transceivers operate from a single +3.3V power supply over an operating case temperature range of -5°C to +70°C (“B” option) or -5°C to +85°C (“E” option). The housing is made of metal to enhance EMI protection. Digital Diagnostics through Serial Interface APD Receiver Up to 120km with Single Mode Fiber Loss of Signal Output & Tx Disable Input Hot-pluggable Eye Safe (Class I Laser Safety) Duplex LC Optical Interface Single +3.3V Power Supply Absolute Maximum Ratings Parameter Storage Temperature Operating Case Temperature 1 “B” option “E” option Supply Voltage Maximum Input Optical Power (30 seconds max.) Input Voltage 1 Symbol Minimum Maximum Units Tst - 40 + 85 °C -5 + 70 -5 + 85 Vcc 0 + 5.0 V - - + 3.0 dBm Vin 0 Vcc V Top °C Measured on top side of SFP module at the front center vent hole of the cage. An Oplink Company RevB-NP. 2009.02.04 TRPAG1VXIxMS Transmitter Performance Characteristics (Over Operating Case Temperature, VCC = 3.13 to 3.47V) All parameters guaranteed only at typical data rate Parameter Symbol Minimum Typical Maximum Units Operating Data Rate 1 B - 1250 - Mb/s Optical Output Power PO 0 - + 5.0 dBm Center Wavelength λC 1500 1550 1580 nm Δλ20 - - 1.0 nm Side Mode Suppression Ratio SMSR 30 - - dB Extinction Ratio Phi /Plo 9 - - dB Deterministic Jitter DJ - - 80 ps Total Jitter TJ - - 227 ps - - - 2.0 dB Spectral Width (-20dB) Dispersion Penalty 2 Transmitter Output Eye 1 2 Compliant with Eye Mask Defined in IEEE 802.3z Standard Data rate ranges from 125Mb/s to 1300Mb/s. However, some degradation may be incurred in overall performance. Specified at 2400ps/nm dispersion, which corresponds to the approximate worst-case dispersion for 120km G.652 fiber respectively over the wavelength range of 1500 to 1580nm. Receiver Performance Characteristics (Over Operating Case Temperature, VCC = 3.13 to 3.47V) All parameters guaranteed only at typical data rate Parameter Symbol Minimum Typical Maximum Units B - 1250 - Mb/s Minimum Input Optical Power (10-12 BER) 2 Pmin - 32.5 - 35.0 - dBm Maximum Input Optical Power (10 BER) Pmax - 10.0 - - dBm Operating Data Rate 1 -12 LOS Thresholds LOS Timing Delay 2 Increasing Light Input Plos+ - - - 32.0 Decreasing Light Input Plos- - 45.0 - - Increasing Light Input t_loss_off - - 100 Decreasing Light Input t_loss_on - - 100 dBm µs - 0.5 - - dB Deterministic Jitter DJ - - 170 ps Total Jitter TJ - - 266 ps LOS Hysteresis λ 1100 - 1600 nm ORL 12 - - dB - - - 1500 MHz Wavelength of Operation Optical Return Loss Electrical 3dB Upper Cutoff Frequency 1 2 Data rate ranges from 125Mb/s to 1300Mb/s. However, some degradation may be incurred in overall performance. Measured with 27-1 PRBS at 1250Mb/s and 1550nm wavelength. Laser Safety: All transceivers are Class I Laser products per FDA/CDRH and IEC-60825 standards. They must be operated under specified operating conditions. Oplink Communications, Inc. DATE OF MANUFACTURE: This product complies with 21 CFR 1040.10 and 1040.11 Meets Class I Laser Safety Requirements Oplink Communications, Inc. 2 RevB-NP. 2009.02.04 TRPAG1VXIxMS Transmitter Electrical Interface (Over Operating Case Temperature, VCC = 3.13 to 3.47V) Parameter Symbol Minimum Input Voltage Swing (TD+ & TD-) 1 VPP-DIF Input HIGH Voltage (TX DISABLE) 2 VIH Input LOW Voltage (TX DISABLE) 2 Output HIGH Voltage (TX_FAULT) 3 Output LOW Voltage (TX_FAULT) 3 Typical Maximum Units 0.35 - 1.75 V 2.0 - VCC V VIL 0 - 0.8 V VOH 2.0 - VCC + 0.3 V VOL 0 - 0.8 V Differential peak-to-peak voltage. There is an internal 4.7 to 10kΩ pull-up resistor to VccT. 3 Open collector compatible, 4.7 to 10kΩ pull-up resistor to Vcc (Host Supply Voltage). 1 2 Receiver Electrical Interface (Over Operating Case Temperature, VCC = 3.13 to 3.47V) Parameter Symbol Minimum Typical Maximum Units VPP-DIF 0.4 - 1.75 V VOH VCC - 1.3 - VCC + 0.3 V VOL 0 - 0.5 V Output Voltage Swing (RD+ & RD-) 1 Output HIGH Voltage (LOS) 2 Output LOW Voltage (LOS) 2 1 2 Differential peak-to-peak voltage across external 100Ω load. Open collector compatible, 4.7 to 10kΩ pull-up resistor to Vcc (Host Supply Voltage). Electrical Power Supply Characteristics (Over Operating Case Temperature, VCC = 3.13 to 3.47V) Parameter Symbol Minimum Typical Maximum Units Supply Voltage VCC 3.13 3.3 3.47 V Supply Current ICC - 175 300 mA Module Definition MOD_DEF(0) pin 6 MOD_DEF(1) pin 5 MOD_DEF(2) pin 4 Interpretation by Host TTL LOW SCL SDA Serial module definition protocol Electrical Pad Layout Host Board Connector Pad Layout 20 TX GND 1 TX GND 19 TD- (TX DATA IN-) 2 TX Fault 1 18 TD+ (TX DATA IN+) 3 TX Disable 2 17 TX GND 4 MOD_DEF(2) 3 16 VccTX 5 MOD_DEF(1) 4 15 VccRX 6 MOD_DEF(0) 14 RX GND 7 NO CONNECTION 6 13 RD+ (RX DATA OUT+) 8 LOS 7 12 RD- (RX DATA OUT-) 9 RX GND 8 11 RX GND 10 RX GND 9 Top of Board Oplink Communications, Inc. Toward Bezel 5 10 Bottom of Board (as viewed thru top of board) 3 20 19 18 17 16 15 Toward ASIC 14 13 12 11 RevB-NP. 2009.02.04 TRPAG1VXIxMS Example of SFP host board schematic Vcc 3.3V 1µH coil or ferrite bead (<0.2Ω series resistance) Vcc 3.3V + 10 0.1 0.1 + 10 0.1 R 16 2 15 TRPAG1VX 3 TX Disable 100 50Ω line TX DATA IN+ TX DATA IN- 50Ω line R MOD_DEF(2) MOD_DEF(1) 6 50Ω line 13 19 12 R TX Fault LOS 8 4 5 18 R 50Ω line MOD_DEF(0) (100Ω to ground internally) RX DATA OUT+ to 50Ω load RX DATA OUTto 50Ω load 1, 9, 10, 11, 14, 17, 20 R: 4.7 to 10kΩ Application Notes Electrical Interface: All signal interfaces are compliant with the SFP MSA specification. The high speed DATA interface is differential AC-coupled internally with 0.1μF and can be directly connected to a 3.3V SERDES IC. All low speed control and sense output signals are open collector TTL compatible and should be pulled up with a 4.7 - 10kΩ resistor on the host board. up, MOD_DEF(1:2) appear as NC (no connection), and MOD_DEF(0) is TTL LOW. When the host system detects this condition, it activates the serial protocol (standard two-wire I2C serial interface) and generates the serial clock signal (SCL). The positive edge clocks data into the EEPROM segments of the SFP that are not write protected, and the negative edge clocks data from the SFP. Loss of Signal (LOS): The Loss of Signal circuit monitors the level of the incoming optical signal and generates a logic HIGH when an insufficient photocurrent is produced. The serial data signal (SDA) is for serial data transfer. The host uses SDA in conjunction with SCL to mark the start and end of serial protocol activation. The supported monitoring functions are temperature, voltage, bias current, transmitter power, average receiver signal, all alarms and warnings, and software monitoring of TX Fault/LOS. The device is internally calibrated. TX Fault: The output indicates LOW when the transmitter is operating normally, and HIGH with a laser fault including laser end-of-life. TX Fault is an open collector/drain output and should be pulled up with a 4.7 - 10kΩ resistor on the host board. TX Fault is non-latching (automatically deasserts when fault goes away). The data transfer protocol and the details of the mandatory and vendor specific data structures are defined in the SFP MSA, and SFF-8472, Rev. 9.3. TX Disable: When the TX Disable pin is at logic HIGH, the transmitter optical output is disabled (less than -45dBm). Power Supply and Grounding: The power supply line should be well-filtered. All 0.1μF power supply bypass capacitors should be as close to the transceiver module as possible. Serial Identification and Monitoring: The module definition of SFP is indicated by the three module definition pins, MOD_DEF(0), MOD_DEF(1) and MOD_DEF(2). Upon power Oplink Communications, Inc. 4 RevB-NP. 2009.02.04 TRPAG1VXIxMS Package Outline 54.6 2.15 1.27 .05 MAX 13.56 .53 15.67 .62 8.51 .34 9.55 .38 1 .04 MAX 6.25±0.051 .25±.002 1 .04 FRONT EDGE OF TRANSCEIVER CAGE 47.50 1.87 REF 46335 Landing Pkwy Fremont, CA 94538 Tel: (510) 933-7200 Fax: (510) 933-7300 Email: [email protected] • www.oplink.com 8.9 .35 13.9±0.1 .546±.004 1.8 .07 41.8±0.15 1.645±.006 45±0.20 1.772±.008 Dimensions in inches [mm] Default tolerances: .xxx = ± .005”, .xx = ± .01” Ordering Information Oplink can provide a remarkable range of customized optical solutions. For detail, please contact Oplink’s Sales and Marketing for your requirements and ordering information (510) 933-7200 or [email protected]. Oplink Communications, Inc. reserves the right to make changes in equipment design or specifications without notice. Information supplied by Oplink Communications, Inc. is believed to be accurate and reliable. However, no responsibility is assumed by Oplink Communications, Inc. for its use nor for any infringements of third parties, which may result from its use. No license is granted by implication or otherwise under any patent right of Oplink Communications, Inc. RevB-NP. 2009.02.04 © 2008, Oplink Communications, Inc. 5