OC-3/STM-1 SFP CWDM Transceivers with Digital Diagnostics TRPA03 CWDM Product Description The TRPA03 CWDM SFP series of fiber optic transceivers with integrated digital diagnostics monitoring functionality provide a quick and reliable interface for long reach (LR) applications. The diagnostic functions, alarm and warning features as described in the Multi-Source Agreement (MSA) document, SFF-8472 (Rev. 9.4), are provided via an I2C serial interface. Products under this series are compatible with SONET/SDH standards for OC-3/ STM-1 LR-2/L-1.2 and are available in eight (8) wavelengths: 1471nm, 1491nm, 1511nm, 1531nm, 1551nm, 1571nm, 1591nm and 1611nm. Two optical link power budgets are available, 32dB and 34dB, providing an extra 3dB and 5dB over SONET/ SDH link budgets, respectively, to accommodate the wavelength multiplexing and de-multiplexing insertion losses. All modules satisfy Class I Laser Safety requirements in accordance with the U.S. FDA/CDRH and international IEC-60825 standards. The TRPA03 CWDM transceivers connect to standard 20-pad connectors for hot plug capability. This allows the system designer to make configuration changes or maintenance by simply plugging in different types of transceivers without removing the power supply from the host system. The transceivers have colored bail-type latches, which offer an easy and convenient way to release the modules. The latch is compliant with the SFP MSA. The transmitter and receiver DATA interfaces are AC-coupled internally. LV-TTL Transmitter Disable control input and Loss of Signal output interfaces are also provided. The transceivers operate from a single +3.3V power supply over an operating case temperature range of -5°C to +70°C (“B” option) or -5°C to +85°C (“E” option). The housing is made of plastic and metal for EMI immunity. Features Eight (8) Wavelength CWDM Transceivers Compatible with SFP MSA Compatible with SONET/SDH OC-3/STM-1 (155Mb/s) LR-2/L-1.2 Long Reach Specifications Digital Diagnostics through Serial Interface Internal Calibration for Digital Diagnostics Optical Link Power Budgets of 32dB & 34dB Minimum Eye Safe (Class I Laser Safety) Duplex LC Optical Interface Excellent EMI & ESD Protection Hot-pluggable TX Fault & Loss of Signal Outputs TX Disable Input Absolute Maximum Ratings Parameter Storage Temperature Operating Case Temperature1 “B” Option “E” Option Symbol Minimum Maximum Units TST - 40 + 85 °C -5 + 70 -5 + 85 TOP °C Supply Voltage VCC 0 + 5.0 V Input Voltage VIN 0 VCC V 1 Measured on top side of SFP module at the front center vent hole of the cage. An Oplink Company RevC-NP.2009.02.17 TRPA03 CWDM Transmitter Performance Characteristics (Over Operating Case Temperature, VCC = 3.13 to 3.47V) All parameters guaranteed only at typical data rate Parameter Symbol Minimum Typical Maximum Units B - 156 - Mb/s - 2.0 - + 3.0 0 - + 5.0 10 - - 1471 1464.5 1471 1477.5 1491 1484.5 1491 1497.5 1511 1504.5 1511 1517.5 1524.5 1531 1537.5 1544.5 1551 1557.5 1571 1564.5 1571 1577.5 1591 1584.5 1591 1597.5 Operating Data Rate 1 Average Optical Output Power (coupled into single mode fiber), 50% duty cycle TRPA03L2HBxSx TRPA03L2IBxSx PO Phi /Plo Extinction Ratio 1531 Center Wavelength 1551 λC 1611 Spectral Width (-20dB) Side Mode Suppression Ratio dB nm 1604.5 1611 1617.5 Δλ20 - - 1.0 nm SMSR 30 - - dB Optical Output Eye 1 dBm Compliant with Telcordia GR-253-CORE and ITU-T Recommendation G.957 Data rate ranges from 50Mb/s to 266Mb/s. However, some degradation may be incurred in overall performance. Receiver Performance Characteristics (Over Operating Case Temperature, VCC = 3.13 to 3.47V) All parameters guaranteed only at typical data rate Parameter Operating Data Rate 1 LOS Timing Delay Typical Maximum Units B - 156 - Mb/s Pmin - 34.0 - 37.0 - dBm - 7.0 0 - dBm Increasing Light Input Plos+ - - - 34.0 Decreasing Light Input Plos- - 45.0 - - Increasing Light Input t_loss_off - - 100 Decreasing Light Input t_loss_on 2.3 - 100 2 Maximum Input Optical Power (10 -12 BER) 2 LOS Thresholds Minimum Pmax Receiver Sensitivity (10 BER) -10 Symbol dBm μs LOS Hysteresis - 1.0 - - dB Wavelength of Operation λ 1100 - 1620 nm Receiver Reflectance - - - - 25.0 dB 1 2 Data rate ranges from 50Mb/s to 266Mb/s. However, some degradation may be incurred in overall performance. Measured with 223-1 PRBS at 156Mb/s. Oplink Communications, Inc. Laser Safety: All transceivers are Class I Laser products per FDA/CDRH and IEC-60825 standards. They must be operated under specified operating conditions. Oplink Communications, Inc. DATE OF MANUFACTURE: This product complies with 21 CFR 1040.10 and 1040.11 Meets Class I Laser Safety Requirements 2 RevC-NP.2009.02.17 TRPA03 CWDM Transmitter Electrical Interface (Over Operating Case Temperature, VCC = 3.13 to 3.47V) Parameter Input Voltage Swing (TD+ & TD-) 1 Input HIGH Voltage (TX Disable) 2 Symbol Minimum Typical Maximum Units VPP-DIF 0.25 - 2.4 V VIH 2.0 - VCC V VIL 0 - 0.8 V Output HIGH Voltage (TX Fault) 3 VOH 2.0 - VCC + 0.3 V Output LOW Voltage (TX Fault) VOL 0 - 0.8 V Input LOW Voltage (TX Disable) 1 2 3 2 3 Differential peak-to-peak voltage. There is an internal 4.7 to 10kΩ pull-up resistor to VccT. Open collector compatible, 4.7 to 10kΩ pull-up resistor to Vcc (Host Supply Voltage). Receiver Electrical Interface (Over Operating Case Temperature, VCC = 3.13 to 3.47V) Parameter Symbol Minimum Typical Maximum Units VPP-DIF 0.6 - 2.0 V Output HIGH Voltage (LOS) 2 VOH 2.0 - VCC + 0.3 V Output LOW Voltage (LOS)) 2 VOL 0 - 0.5 V Output Voltage Swing (RD+ & RD-) 1 1 2 Differential peak-to-peak voltage across external 100Ω load. Open collector compatible, 4.7 to 10kΩ pull-up resistor to Vcc (Host Supply Voltage). Electrical Power Supply Characteristics (Over Operating Case Temperature, VCC = 3.13 to 3.47V) Parameter Symbol Minimum Typical Maximum Units Supply Voltage VCC 3.13 3.3 3.47 V Supply Current ICC - 175 245 mA Module Definition MOD_DEF(0) pin 6 MOD_DEF(1) pin 5 MOD_DEF(2) pin 4 Interpretation by Host TTL LOW SCL SDA Serial module definition protocol Electrical Pad Layout Host Board Connector Pad Layout 20 TX GND 1 TX GND 19 TD- (TX DATA IN-) 2 TX Fault 1 18 TD+ (TX DATA IN+) 3 TX Disable 2 17 TX GND 4 MOD_DEF(2) 3 16 VccTX 5 MOD_DEF(1) 4 15 VccRX 6 MOD_DEF(0) 14 RX GND 7 NO CONNECTION 6 13 RD+ (RX DATA OUT+) 8 LOS 7 12 RD- (RX DATA OUT-) 9 RX GND 8 11 RX GND 10 RX GND 9 Top of Board Oplink Communications, Inc. Toward Bezel 5 10 Bottom of Board (as viewed thru top of board) 3 20 19 18 17 16 15 Toward ASIC 14 13 12 11 RevC-NP.2009.02.17 TRPA03 CWDM Example of SFP host board schematic Vcc 3.3V 1µH coil or ferrite bead (<0.2Ω series resistance) Vcc 3.3V + 0.1 10 0.1 + 10 0.1 R 16 15 TRPA03 CWDM 3 TX Disable 100 50Ω line TX DATA IN+ TX DATA IN- 50Ω line R 2 MOD_DEF(2) MOD_DEF(1) 6 50Ω line 13 19 12 R TX Fault LOS 8 4 5 18 R 50Ω line MOD_DEF(0) (100Ω to ground internally) RX DATA OUT+ to 50Ω load RX DATA OUTto 50Ω load 1, 9, 10, 11, 14, 17, 20 R: 4.7 to 10kΩ Application Notes Electrical Interface: All signal interfaces are compliant with the SFP MSA specification. The high speed DATA interface is differential AC-coupled internally with 0.1μF and can be directly connected to a 3.3V SERDES IC. All low speed control and sense output signals are open collector TTL compatible and should be pulled up with a 4.7 - 10kΩ resistor on the host board Upon power up, MOD_DEF(1:2) appear as NC (no connection), and MOD_DEF(0) is TTL LOW. When the host system detects this condition, it activates the serial protocol (standard two-wire I2C serial interface) and generates the serial clock signal (SCL). The positive edge clocks data into the EEPROM segments of the SFP that are not write protected, and the negative edge clocks data from the SFP. Loss of Signal (LOS): The Loss of Signal circuit monitors the level of the incoming optical signal and generates a logic HIGH when an insufficient photocurrent is produced. The serial data signal (SDA) is for serial data transfer. The host uses SDA in conjunction with SCL to mark the startand end of serial protocol activation. The supported monitoring functions are internal temperature, supply voltage, bias current, transmitter power, average receiver signal, all alarms and warnings and software monitoring of TX Fault/LOS. The device is internally calibrated. TX_Fault: The output indicates LOW when the transmitter is operating normally, and HIGH with a laser fault including laser end-of-life. TX Fault is an open collector/drain output that should be pulled up with a 4.7 - 10kΩ resistor on the host board. TX Fault is non-latching (automatically deasserts when fault goes away). The data transfer protocol and the details of the mandatory and vendor specific data structures are defined in the SFP MSA, and SFF-8472, Rev. 9.4 TX_Disable: When the TX Disable pin is at logic HIGH, the transmitter optical output is disabled (less than -45dBm). Power Supply and Grounding: The power supply line should be well-filtered. All 0.1μF power supply bypass capacitors should be as close to the transceiver module as possible. Serial Identification and Monitoring: The module definition of SFP is indicated by the three module definition pins, MOD_DEF(0), MOD_DEF(1) and MOD_DEF(2). Oplink Communications, Inc. 4 RevC-NP.2009.02.17 TRPA03 CWDM 46335 Landing Pkwy Fremont, CA 94538 Tel: (510) 933-7200 Fax: (510) 933-7300 Email: [email protected] • www.oplink.com Mechanical Package Dimensions in inches [mm] Default tolerances: .xxx = + .005”, .xx = + .01” Ordering Information Oplink can provide a remarkable range of customized optical solutions. For detail, please contact Oplink’s Sales and Marketing for your requirements and ordering information (510) 933-7200 or [email protected]. Oplink Communications, Inc. reserves the right to make changes in equipment design or specifications without notice. Information supplied by Oplink Communications, Inc. is believed to be accurate and reliable. However, no responsibility is assumed by Oplink Communications, Inc. for its use nor for any infringements of third parties, which may result from its use. No license is granted by implication or otherwise under any patent right of Oplink Communications, Inc. RevC-NP.2009.02.17 © 2006, Oplink Communications, Inc. 5