10/100 Base-X Module for ICS 1890 & SSI 78Q2120 Multi-Port Applications ELECTRONICS INC. EPF8047S • Significantly improved common mode attenuation • • Guaranteed to operate with 8 mA DC bias at 70°C • • Complies with or exceeds IEEE 802.3, 10 BT/100 BX Standards • Electrical Parameters @ 25° C Insertion Loss (dB Max.) OCL @ 70°C 100 KHz, 0.1 Vrms 8 mA DC Bias Media Side 0.1-80 MHz Return Loss (dB Min.) 80-100 MHz 150 MHz 1-30 MHz Common Mode Rejection (dB Min.) 30-60 MHz 100 MHz 30-100 MHz 200 MHz Crosstalk (dB Min.) [Between Channels] 300-500 MHz 0.1-60 MHz 60-100 MHz -35 -35 Xmit Rcv Xmit Rcv Xmit Rcv Xmit Rcv Xmit Rcv Xmit Rcv Xmit Rcv Xmit Rcv Xmit Rcv -1 350µH -1 -1 • -1 -3 -3 -18 Isolation : 1500 Vrms • -18 -18 -18 -10 -10 -40 -40 -30 -20 Impedance : 100 Ω • Rise Time : 3.0 nS Max. -20 -10 • Schematic Receive Channel 6, 16 Transmit Channel 2, 12 35, 25 7, 17 8, 18 34, 24 3, 13 33, 23 4, 14 Media Side Media Side Dimensions A N J B Q 40 21 P Solder Pad Layout 1 20 D M I K C F H E 37, 27 Chip Side Package PCA EPF8047S Date Code 38, 28 1 CT:1CT 1 CT:1CT Chip Side 39, 29 C M T Dim. Min. A B C D E F G H I J K L M N P Q 1.110 .470 .240 .950 .008 .050 .620 .016 .008 .085 0° .045 (Inches) Max. Nom. 1.130 .490 .250 Typ. .012 Typ. .630 .022 .012 Typ. 8° Typ. (Millimeters) Min. Max. Nom. 28.19 28.70 11.94 12.45 6.10 6.35 24.13 Typ. .203 .305 1.27 Typ. 15.75.. 16.00 406 .559 .203 .305 2.16 Typ. 0° 8° 1.14 Typ. .030 .050 .090 .670 .762 1.27 2.29 17.02 L G PCA ELECTRONICS, INC. 16799 SCHOENBORN ST. NORTH HILLS, CA 91343 CSF8047Sa Rev. Orig. 1/8/97 TEL: (818) 892-0761 FAX: (818) 894-5791 http://www.pcainc.com 10/100 Base-X Module for ICS 1890 & SSI 78Q2120 Multi-Port Applications ELECTRONICS INC. EPF8047S The circuit below is a guideline for interconnecting PCA’s EPF8047S with ICS 1890 chip for 10/100 Mb/s applications. Further details can be obtained from the chip manufacturer application notes. Connection to the alternative chip SSI 78Q2120 is straight forward; please consult the SSI data sheet recommendations for completing this project. Typical insertion loss of the isolation transformer is 0.5dB. This parameter covers the entire spectrum of the encoded signals in 10/100 protocols. Under terminated conditions, to transmit a 2V pk-pk signal across the cable, you must adjust the chips supporting resistor to get at least 2.12V pk-pk across the transmit pins. Primary side center taps can be returned to the chip side ground plane; but more often than not, if the ground plane is itself noisy, field experience has shown that it may worsen EMI situation. It is perhaps wiser to carefully lay the system borad so that substantial gain in EMI suppression is obtained from the so called “common mode termination” on the cable side as shown below. In any event, this configuration has been known to be quite successful in the field in EMI containment for similar applications. The phantom resistors shown around the connector have been known to suppress unwanted radiation that unused wires pick up from the immediate environment. Their placement and use are to be considered carefully before a design is finalized. It is recommended that there be a neat separation of ground planes in the layout. It is generally accepted practice to limit the plane off at least 0.05 inches away from the chip side pins of EPF8047S. There need not be any ground plane beyond this plane. For best results, PCB designer should design the outgoing traces preferably to be 50 Ω, balanced and well coupled to achieve minimum radiation from these traces. Typical Application Circuit for UTP (only one port shown) 5Vcc 3 ICS 1890 35 1 33 2 39 3 TX+ 2 37 6 TX- 4 34 RX+ 6 38 RX- 8 Rcv Xmit RJ45* 50Ω 75Ω 4 5 50Ω 7 7 8 EPF8047S High Voltage Capacitor CM Capacitor Chassis Ground Notes : Only one port shown for Hub side connection. PCA ELECTRONICS, INC. 16799 SCHOENBORN ST. NORTH HILLS, CA 91343 CSF8047Sb Rev. Orig. 1/8/97 TEL: (818) 892-0761 FAX: (818) 894-5791 http://www.pcainc.com