PFS FR206

FAST RECOVERY RECTIFIER
FR201
THRU
VOLTAGE
CURRENT
FR207
RANGE
50 to 1000 Volts
2.0 Ampere
FEATURES
Low cost construction.
Fast switching for high efficiency.
Low reverse leakage
High forward surge current capability.
High temperature soldering guaranteed:
260/10 seconds, 0.375" (9.5mm)lead length
at 5 lbs (2.3kg) tension.
MECHANICAL DATA
Case: transfer molded plastic
Epoxy: UL94V - 0 rate flame retardant.
Polarity: Color band denotes cathode end.
Lead: Plated axial lead, solderable per MIL - STD - 202E
method 208C
Mounting position: Any
Weight: 0.014 ounce, 0.39grams
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Ratings at 25 ambient temperature unless otherwise specified
Single phase, half wave, 60Hz, resistive or inductive load.
For capacitive load derate current by 20%
Maximum Repetitive Peak Reverse Voltage
Maximum RMS Voltage
Maximum DC Blocking Voltage
Maximum Average Forward Rectified Current,
0.375" (9.5mm) lead length at TA =75
Peak Forward Surge Current
8.3ms single half sine - wave superimposed on
rated load (JEDEC method )
Maximum Instantaneous Forward Voltage at 2.0A
Maximum DC Reverse Current at rated TA = 25
TA DC blocking voltage
Maximum Reverse Recovery Time (Note 3) Tj = 25
Typical Junction Capacitance (Note 1)
Typical Thermal Resistance (Note2)
Operating and Storage Temperature Range
Storage Temperature Range
SYMBOLS FR201 FR202
VRRM
50
100
VRMS
35
70
VDC
50
100
FR203
200
140
200
FR204
400
280
400
FR205
600
420
600
FR26 FR207 UNIT
Volts
Volts
Volts
I(AV)
Amps
IFSM
Amps
VF
Volts
IR
trr
CJ
R
TJ
TSTG
NOTES:
1. Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts.
2. Thermal Resistance from Junction to Ambient at 0.375" (9.5mm) lead length, P.C. board mounted.
3. Reverse Recovery Test Condition: IF =0.5A, IR = 1.0A, IRR = 0.25A
Web Site: WWW.PS-PFS.COM
150
A
250
25
40
(-65 to +150)
(-65 to +150)
500
nS
pF
/W
RATINGS AND CHARACTERISTIC CURVES FR201 THRU FR207
FIG.2-MAXIMUM NON-REPETITIVE PEAK
FIG.1-TYPICAL FORWARD CURRENT
FORWARD SURGE CURRENT
0.375"(9.5mm)
60
8.3ms Single Half Sine-Wave
(JEDEC Method) =T T j
j max
50
CURRENT, (A)
PEAK FORWARD SURGE
70
40
30
20
10
1 Cycle
0
1
2
4
6
8
20
10
60 80 100
40
NUMBER OF CYCLES AT 60 Hz
FIG.3-TYPICAL INSTANTANEOUS
FIG.4-TYPICAL REVERSE
FORWARD CHARACTERISTICS
CHARACTERISTICS
10
1.0
T =25 ° C
Pulse Width=300uS
1% Duty Cycle
j
0.1
0.01
0.4
1.0
0.8
0.6
1.2
1.4
1.6
T =100 ° C
j
1.0
(uA)
INSTANTANEOUS REVERSE CURRENT,
10
(A)
INSTANTANEOUS FORWARD CURRENT,
20
0.1
T =25 ° C
j
0.01
0
1.8
40
60
100
80
120
140
PERCENT OF RATED PEAK
INSTANTANEOUS FORWARD VOLTAGE,(V)
REVERSE VOLTAGE,(%)
FIG.6-TEST CIRCUIT DIAGRAM AND
FIG.5-TYPICAL JUNCTION CAPACITANCE
REVERSE RECOVERY TIME CHARACTERISTIC
100
JUNCTION CAPACITANCE,(pF)
20
50
NONINDUCTIVE
Trr
10
NONINDUCTIVE
+0.5A
(-)
(+)
25 Vdc
(approx.)
10
(-)
PULSE
GENERATIOR
(NOTE 2)
D.U.T.
1
NON
INDUCTIVE
0
-0.25A
(+)
OSCILLOSCOPE
(NOTE 1)
Tj =25 ° C
f=1MHz
V sig =50mV
NOTES: 1.Rise Time =7ns max. Input Impedance=
p-p
1 megohm. 22pF
2.Rise time=10ns max. Source Impedance=
1
0.1
1.0
10
100
50 ohms
REVRESE VOLTAGE,(V)
Web Site: WWW.PS-PFS.COM
-1.0A
1cm
SET TIME BASE FOR
50/100ns/cm