PL611-25 Programmable Quick Turn Clock T M FEATURES PAD LAYOUT AND DIE ID • • • • • Advanced programmable PLL design Very low Jitter and Phase Noise (< 40ps Pk-Pk typical) Two registers banks for 2-time programming. Output frequency up to 200MHz CMOS. Crystal inputs: o Fundamental crystal: 10MHz-30MHz o 3 RD overtone crystal: Up to 75MHz • Single 2.5V or 3.3V ± 10% power supply • Operating temperature range from -40°C to 85°C • Available in Die form only XOUT XIN 1 9 OE 2 DNC GND 3 Die ID: C611A- 8 0505-05D 7 VDD GND 4 CLK1 5 6 VDD DIE AND WAFER SPECIFICATION Name Value Die Size 31.5x55.1 mil Reverse side GND Pad Opening 80 micron x 80 micron Wafer Diameter 8” Die Per Wafer 22,277 Wafer Thickness 12 mil DESCRIPTION generate any output frequency up to 200 MHz from fundamental crystal input between 10 MHz - 30 MHz, or a 3rd overtone crystal of up to 75Mhz. The PL611-25 is a low-cost general purpose frequency synthesizer and a member of PhaseLink’s Factory Programmable ‘Quick Turn Clock (QTC)’ family. PhaseLink’s PL611-25 product family can BLOCK DIAGRAM XIN/FIN XOUT Xtal OSC Programmable CLoad R-counter (8-bit) Phase Detector Charge Pump Loop Filter M -counter (10-bit) FVCO = F Ref. * (2 * M /R) VCO P-counter (5-bit) Programmable Function FOut = FVCO / (2 * P) 47745 Fremont Blvd., Fremont, California 94538 Tel (510) 492-0990 Fax (510) 492-0991 CLK1 Rev 10/05/05 Page 1 PL611-25 Programmable Quick Turn Clock T M KEY PROGRAMMING PARAMETERS CLK[ 0:2 ] Output Frequency Output Drive Strength Fout = FIN * M / (R * P) where M=10 bit R= 8 bit P= 5 bit CLK1= VCO / 2 * P Crystal Load Std: 10mA (default) # of Register Banks +/- 200ppm tuning. 2 Charge-Pump Current 4 levels of pump current setting High: 24mA PAD ASSIGNMENT and DESCRIPTION Pad # Die Pads X (µm) Y(µm) XIN 1 101.5 1274.0 I Crystal input. OE 2 101.5 1075.0 I Output Enable GND 3 101.5 878.4 P GND connection. GND 4 101.5 671.8 P GND connection. CLK1 5 101.5 425.0 O Programmable Clock Output. 6 697 483.0 7 697 790.0 P VDD connection. DNC 8 697 1024.0 - Do Not Connect XOUT 9 697 1274.0 O Crystal output. Name VDD Type Description 47745 Fremont Blvd., Fremont, California 94538 Tel (510) 492-0990 Fax (510) 492-0991 Rev 10/05/05 Page 2 PL611-25 Programmable Quick Turn Clock T M ELECTRICAL SPECIFICATIONS ABSOLUTE MAXIMUM RATINGS PARAMETERS SYMBOL MIN. MAX. UNITS V DD - 0.5 4.6 V Input Voltage Range VI - 0.5 V DD + 0.5 V Output Voltage Range VO - 0.5 V DD + 0.5 V Supply Voltage Range Data Retention @ 85º C 10 Years 260 °C -65 150 °C -40 +85 °C Soldering Temperature (Green Package) Storage Temperature TS Ambient Operating Temperature* Note: Exposure of the device under conditions beyond the limits specified by Maximum Ratings for extended periods may cause permanent damage to the device and affect product reliability. These conditions represent a stress rating only, and functional operations of the device at these or any other conditions above the operational limits noted in this specification is not implied. * Note: Operating Temperature is guaranteed by design for all parts (COMMERCIAL and INDUSTRIAL), but tested for COMMERCIAL grade only. AC SPECIFICATIONS PARAMETERS MAX. UNITS 30 MHz 3 rd Overtone Crystal 75 MHz Settling Time At power-up (after VDD increases over 1.62V) 10 ms VDD Sensitivity Frequency vs. VDD+/-10% 2 ppm Crystal Input Frequency Output Rise Time Output Fall Time CONDITIONS Fundamental Crystal MIN. TYP. 10 -2 15pF Load, 10/90%VDD, Standard drive 2.5 3.5 ns 15pF Load, 10/90%VDD, High drive 1.0 1.5 ns 15pF Load, 90/10%VDD, Standard drive 2.5 3.5 ns 15pF Load, 90/10%VDD, High drive 1.0 1.5 ns 50 55 % 500 ps Duty Cycle At VDD/2 Max. output skew between same frequency clocks Equal loading (15 pF). Equal frequency & drive strength Period Jitter, peak-to-peak* (measured from 10,000 samples) With capacitive decoupling between VDD and GND. Operating only one output. 45 40 ps * Note: Jitter performance depends on the programming parameters. 47745 Fremont Blvd., Fremont, California 94538 Tel (510) 492-0990 Fax (510) 492-0991 Rev 10/05/05 Page 3 PL611-25 Programmable Quick Turn Clock T M DC SPECIFICATIONS PARAMETERS SYMBOL CONDITIONS MIN. TYP. MAX. UNITS 15 mA 3.63 V 0.4 V Supply Current, Dynamic, with Loaded Outputs I DD Operating Voltage V DD Output Low Voltage V OL I OL = +4mA (Standard drive) Output High Voltage V OH I OH = -4mA (Standard drive) I OSD V OL = 0.4V, V OH = 2.4V (Standard drive) 10 mA I OHD V OL = 0.4V, V OH = 2.4V (High Drive) 24 mA ±50 mA Output Current Short-circuit Current At 10MHz, load=15pF 2.25 V DD – 0.4 IS V CRYSTAL SPECIFICATIONS PARAMETERS SYMBOL MIN. Fundamental Crystal Resonator Frequency F XIN 10 3rd Overtone Crystal Resonator Frequency F XIN Crystal Loading Rating (The IC can be programmed for any value in this range.) C L (xtal) TYP. 5 Maximum Sustainable Drive Level Operating Drive Level MAX. UNITS 30 MHz 75 MHz 20 pF 500 µW µW 100 Crystal Shunt Capacitance C0 6 pF RS 30 Ω ESR 100/70 Ω Effective Series Resistance, 3 rd Overtone, 50-65MHz, [CO< 4pF, C L =5pF/8pF] ESR 60/40 Ω Effective Series Resistance, 3 rd Overtone, 65-75MHz [CO< 4pF, C L =5pF/8pF ESR 45/30 Ω Effective Series Resistance, Fundamental, 10-30MHz Effective Series Resistance, [CO< 4pF, C L =5pF/8pF] 3 rd Overtone, 30-50MHz Note: A detailed crystal specification document is also available for this part 47745 Fremont Blvd., Fremont, California 94538 Tel (510) 492-0990 Fax (510) 492-0991 Rev 10/05/05 Page 4 PL611-25 Programmable Quick Turn Clock T M ORDERING INFORMATION For part ordering, please contact our Sales Department: 47745 Fremont Blvd., Fremont, CA 94538, USA Tel: (510) 492-0990 Fax: (510) 492-0991 PART NUMBER The order number for this device is a combination of the following: Device number, Package type and Operating temperature range PL611-25 WX PART NUMBER TEMPERATURE C=COMMERCIAL I = INDUSTRIAL PACKAGE TYPE W= WAFER Part / Order Number Marking TEMPERATURE PL611-25WC P611-25WC 0- +70º C PhaseLink Corporation, reserves the right to make changes in its products or specifications, or both at any time without notice. The information furnished by Phaselink is believed to be accurate and reliable. However, PhaseLink makes no guarantee or warranty concerning the accuracy of said information and shall not be responsible for any loss or damage of whatever nature resulting from the use of, or reliance upon this product. LIFE SUPPORT POLICY: PhaseLink’s products are not authorized for use as critical components in life support devices or systems without the express written approval of the President of PhaseLink Corporation. 47745 Fremont Blvd., Fremont, California 94538 Tel (510) 492-0990 Fax (510) 492-0991 Rev 10/05/05 Page 5