TCSA56 2* TO-92 PLASTIC PACKAGE PNP SILICON EPITAXIAL TRANSISTOR ROHS Audio Frequency Low Power Amplifier Applications. E ABSOLUTE MAXIMUM RATINGS (Ta=25ºC unless specified otherwise) VALUE DESCRIPTION SYMBOL VCBO 35 Collector-Base Voltage V 30 Collector-Emitter Voltage CEO CB UNITS V V VEBO 5 V Collector Current IC 500 mA Base Current IB 100 mA Collector Power Dissipation PC 625 mW Tj, Tstg -55 to +150 Emitter-Base Voltage Operating And Storage Junction Temperature Range ELECTRICAL CHARACTERISTICS (Ta=25ºC unless specified otherwise) DESCRIPTION SYMBOL TEST CONDITION ICBO VCB = 35V, IE = 0 Collector Cut Off Current Emitter Cut Off Current IEBO MIN ºC TYP VEB = 5V, IC = 0 MAX 100 UNITS nA 100 nA DC Current Gain *hFE IC = 100mA, VCE = 1V 70 IC = 400mA, VCE = 6V 25 Collector Emitter Saturation Voltage **hFE VCE(sat) IC = 100mA, IB = 10mA 0.25 V Base Emitter Voltage VBE(on) IC = 100mA, VCE = 1V 1.0 V Cob VCB = 6V, IE = 0, f = 1MHz VCE = 6V, IC = 20mA DYNAMIC CHARACTERISTICS Collector Output Capacitance Transition Frequency *CLASSIFICATION *hFE **hFE ft O : 70 - 140 O : 25 Min 240 13 pF 200 MHz Y : 120 - 240 Y : 40 Min TO-92 Plastic Package A Uncontrolled 2 MAX. 5.33 B 4.45 3.18 5.20 4.19 0.41 0.55 SEC AA A A E F 0.35 0.50 5 DEG G 1.14 1.20 1.40 1.40 12.70 — L 1.982 2.082 M 1.03 1.20 All dimensions are in mm E 3 D MIN. 4.32 H K D K Beyond 'L' Solderability Ensured 1 DIM A C D L Dimension With 'L' B G F C 3 2 1 H M F Mold Parting Line PIN CONFIGURATION 1. BASE 2. COLLECTOR 3. EMITTER 3 2 1 The TO-92 Package, Tape and Ammo Pack Drawings are correct as on the date of issue/revision of this Data Sheet. The currently valid dimensions and information, may please be confirmed from the TO-92 Drawing in the Packages and Packing Section of the Product Catalogue. Packing Details PACKAGE STANDARD PACK INNER CARTON BOX OUTER CARTON BOX Details Net Weight/Qty Size Qty Size Qty Gr Wt TO-92 Bulk 1K/polybag 200 gm/1K pcs 3" x 7.5" x 7.5" 5K 17" x 15" x 13.5" 80K 23 kgs TO-92 T&A 2K/ammo box 645 gm/2K pcs 12.5" x 8" x 1.8" 2K 17" x 15" x 13.5" 32K 12.5 kgs TO-92 Tape and Ammo Pack Tape Mechanical Data h T (p) P h h1 Ammo Pack Style Adhesive Tape on Top Side h1 A1 Flat side A H3 H1 D FEE H2 Label C1 W2 C2 Ho Wo L Carrier Strip 186 (7.3") W1 W F1 F2 Do 332 F t1 (1. 43 7" ) P2 t Po (1 3 ") Flat Side of Transistor and Adhesive Tape Visible 2000 pcs./Ammo Pack All dimensions are in mm ITEM BODY WIDTH BODY HEIGHT BODY THICKNESS PITCH OF COMPONENT * 1 FEED HOLE PITCH * 2 FEED HOLE CENTRE TO COMPONENT CENTRE DISTANCE BETWEEN OUTER LEADS * 3 COMPONENT ALIGNMENT SIDE VIEW * 4 COMPONENT ALIGNMENT FRONT VIEW TAPE WIDTH HOLD-DOWN TAPE WIDTH HOLE POSITION HOLD-DOWN TAPE POSITION LEAD WIRE CLINCH HEIGHT COMPONENT HEIGHT LENGTH OF SNIPPED LEADS FEED HOLE DIAMETER * 5 TOTAL TAPE THICKNESS LEAD - TO - LEAD DISTANCE STAND OFF CLINCH HEIGHT LEAD PARALLELISM PULL - OUT FORCE SYMBOL A1 A T P Po SPECIFICATION MIN. NOM. MAX. 4.0 4.8 3.9 12.7 12.7 TOL . NOTES 4.8 5.2 4.2 ± 1.0 ± 0.3 P2 6.35 ± 0.4 F 5.08 + 0.6 - 0.2 h h1 W Wo W1 0 0 18 6 9 W2 Ho H1 L Do t F1, F2 0.5 16 H2 H3 | C1 - C2 | (p) 4 2.54 0.45 6N 1.0 1.3 ± 0.5 ± 0.2 + 0.7 - 0.5 23.25 11.0 1.2 1.45 3.0 0.22 1. Maximum alignment deviation between leads will not to be greater than 0.2mm. 2. Maximum non-cumulative variation between tape feed holes shall not exceed 1 mm in 20 pitches. 3. Holddown tape will not exceed beyond the edge(s) of carrier tape and there shall be no exposure of adhesive. 4. There will be no more than three (3) consecutive missing components in a tape. 5. A tape trailer, having at least three feed holes are provided after the last component in a tape. ± 0.2 ± 0.5 6. Splices should not interfere with the sprocket feed holes. ± 0.2 REMARKS + 0.4 - 0.1 * 1 Cumulative pitch error 1.0 mm/20 pitch * 2 To be measured at bottom of clinch * 3 At top of body * 4 At top of body * 5 t1 0.3 – 0.6 mm DISCLAIMER NOTICE Rectron Inc reserves the right to make changes without notice to any product specification herein, to make corrections, modifications, enhancements or other changes. Rectron Inc or anyone on its behalf assumes no responsibility or liability for any errors or inaccuracies. Data sheet specifications and its information contained are intended to provide a product description only. "Typical" parameters which may be included on RECTRON data sheets and/ or specifications can and do vary in different applications and actual performance may vary over time. Rectron Inc does not assume any liability arising out of the application or use of any product or circuit. Rectron products are not designed, intended or authorized for use in medical, life-saving implant or other applications intended for life-sustaining or other related applications where a failure or malfunction of component or circuitry may directly or indirectly cause injury or threaten a life without expressed written approval of Rectron Inc. Customers using or selling Rectron components for use in such applications do so at their own risk and shall agree to fully indemnify Rectron Inc and its subsidiaries harmless against all claims, damages and expenditures.