Transys Electronics L I M I T E D PNP SILICON PLANAR EPITAXIAL TRANSISTORS PN4354 PN4355 PN4356 TO-92 Plastic Package E BC General Purpose Amplifiers DESCRIPTION Collector Emitter Voltage Collector Base Voltage Emitter Base Voltage Collector Current - Continuous Power Dissipation@Ta=25°C Power Dissipation@ Tc=25°C Operating And Storage Junction SYMBOL 4354 4355 4356 UNITS VCEO VCBO VEBO IC PD PD Tj, Tstg 60 60 60 60 5 500 625 1.0 -55 to +150 80 80 V V V mA mW mW °C 4355 4356 UNITS >60 >60 >5 >80 >80 <50 V V V nA <5 <100 uA nA Temperature Range ELECTRICAL CHARACTERISTICS (Ta=25°C Unless Otherwise Specified) DESCRIPTION SYMBOL TEST CONDITION 4354 Collector Emitter Voltage Collector Base Voltage Emitter Base Voltage Collector-Cut off Current VCEO(sus)* VCBO VEBO ICBO IEBO Emitter Cut off Current IC=10mA,IB=0 (pulsed) IC=10uA,IE=0 IE=10uA,IC=0 VCB=50V, IE = 0 VcB=50V, IE = 0, >60 >60 Ta =75°C VBE =4V,IC= 0 DC Current Gain hFE * VCE=10V,IC=100uA VCE=10V,IC=1mA VCE=10V,IC=10mA >25 >40 50-500 >60 >75 100-400 >25 >40 50-250 VCE=10V,IC=100mA VCE=10V,IC=500mA >40 >30 >75 >75 >40 >30 IC=50mA, VCE=10V f=100MHz 1.0-5.0 1.0 - 1.5 1.0 - 5.0 VCE(sat) * IC=150mA,IB=15mA IC=500mA,IB=50mA IC=1A,IB=100mA PN4355 <0.15 <0.5 <0.15 <0.5 <1.0 <0.15 <0.5 Commom Emitter Small Signal Current Gain l hfe l Collector Emitter Sat Voltage V V V PNP SILICON PLANAR EPITAXIAL TRANSISTORS PN4354 PN4355 PN4356 TO-92 Plastic Package E BC ELECTRICAL CHARACTERISTICS (Ta=25°C Unless Otherwise Specified) DESCRIPTION SYMBOL TEST CONDITION 4354 VBE(sat)* IC=150mA,IB=15mA Base Emitter Sat Voltage <0.9 IC=500mA,IB=50mA <1.1 IC=1A,IB=100mA 4355 <0.9 <1.1 <1.2 4356 <0.9 <1.1 UNITS V V V <1.1 <1.1 <1.2 <1.1 V V 4354 4355 4356 UNITS <30 <30 <30 PF <110 <110 <110 PF <100 <100 <100 PF VCC =30V <400 <400 <400 ns VCE =10V,IC=100uA <3.0 <3.0 <3.0 dB PN4355 VBE(on)* Base Emitter On Voltage IC=500mA,VCE=0.5V IC=1A,VCE=1V PN4355 SMALL-SIGNAL SYMBOL TEST CONDITION DYNAMIC CHARACTERISTICS Ccb Collector to Base Capacitance Ceb Emitter to Base Capacitance ton Turn On Time toff Turn off Time Noise Figure NF IE=0, VCB=10V, f=1.0MHZ IC=0, VEB=0.5V, f=1.0MHZ IC =500mA,IB1 =50mA, VCC =30V IC =500mA,IB1=IB2 =50mA, RS=1KΩ,f=1kHZ, BW = 1HZ *Pulse Condition: = 300us, Duty Cycle = 1%. PN4354 PN4355 PN4356 TO-92 Plastic Package TO-92 Plastic Package B TO-92 Transistors on Tape and Ammo Pack Ammo Pack Style MECHANICAL DATA A h Adhesive Tape on Top Side P T h (p) A1 LABEL A 3 2 1 H1 D FEE Carrier Strip FLAT SIDE 8.2" W2 H0 L Wo W1 W 13" t1 F1 t F2 K F 1.7 7" Do P2 Po D A A DIM PIN CONFIGURATION 1. COLLECTOR 2. BASE 3. EMITTER All diminsions in mm. C H F 3 2 1 3 2 1 SEC AA G F All dimensions in mm unless specified otherwise E D Flat Side of Transistor and Adhesive Tape Visible 2000 pcs./Ammo Pack A B C D E F G H K MIN. MAX. 4.32 5.33 4.45 5.20 3.18 4.19 0.41 0.55 0.35 0.50 5 DEG 1.14 1.14 12.70 1.40 1.53 — ITEM SYMBOL BODY WIDTH BODY HEIGHT BODY THICKNESS PITCH OF COMPONENT FEED HOLE PITCH A1 A T P Po FEED HOLE CENTRE TO COMPONENT CENTRE P2 DISTANCE BETWEEN OUTER LEADS COMPONENT ALIGNMENT TAPE WIDTH HOLD-DOWN TAPE WIDTH HOLE POSITION F h W Wo W1 HOLD-DOWN TAPE POSITION LEAD WIRE CLINCH HEIGHT COMPONENT HEIGHT LENGTH OF SNIPPED LEADS FEED HOLE DIAMETER TOTAL TAPE THICKNESS LEAD - TO - LEAD DISTANCEF1, W2 Ho H1 L Do t F2 CLINCH HEIGHT PULL - OUT FORCE H2 (P) SPECIFICATION REMARKS MIN. NOM. MAX. TOL . 4.0 4.8 5.2 4.8 4.2 3.9 12.7 ±1 12.7 ±0.3 CUMULATIVE PITCH ERROR 1.0 mm/20 PITCH 6.35 ±0.4 TO BE MEASURED AT BOTTOM OF CLINCH +0.6 5.08 -0.2 1 0 AT TOP OF BODY 18 ±0.5 6 ±0.2 9 +0.7 -0.5 0.5 ±0.2 16 ±0.5 23.25 11.0 4 ±0.2 1.2 t1 0.3 - 0.6 2.54 +0.4 -0.1 3 6N NOTES 1. MAXIMUM ALIGNMENT DEVIATION BETWEEN LEADS NOT TO BE GREATER THAN 0.2 mm. 2. MAXIMUM NON-CUMULATIVE VARIATION BETWEEN TAPE FEED HOLES SHALL NOT EXCEED 1 mm IN 20 PITCHES. 3. HOLDDOWN TAPE NOT TO EXCEED BEYOND THE EDGE(S) OF CARRIER TAPE AND THERE SHALL BE NO EXPOSURE OF ADHESIVE. 4. NO MORE THAN 3 CONSECUTIVE MISSING COMPONENTS ARE PERMITTED. 5. A TAPE TRAILER, HAVING AT LEAST THREE FEED HOLES ARE REQUIRED AFTER THE LAST COMPONENT. 6. SPLICES SHALL NOT INTERFERE WITH THE SPROCKET FEED HOLES. Packing Detail PACKAGE TO-92 Bulk TO-92 T&A STANDARD PACK Details Net Weight/Qty 1K/polybag 200 gm/1K pcs 2K/ammo box 645 gm/2K pcs INNER CARTON BOX Size Qty 3" x 7.5" x 7.5" 5.0K 12.5" x 8" x 1.8" 2.0K OUTER CARTON BOX Size Qty Gr Wt 17" x 15" x 13.5" 80.0K 23 kgs 17" x 15" x 13.5" 32.0K 12.5 kgs