LM5118, LM5118-Q1 www.ti.com SNVS566G – APRIL 2008 – REVISED FEBRUARY 2013 Wide Voltage Range Buck-Boost Controller Check for Samples: LM5118, LM5118-Q1 FEATURES DESCRIPTION • The LM5118 wide voltage range Buck-Boost switching regulator controller features all of the functions necessary to implement a high performance, cost efficient Buck-Boost regulator using a minimum of external components. The BuckBoost topology maintains output voltage regulation when the input voltage is either less than or greater than the output voltage making it especially suitable for automotive applications. The LM5118 operates as a buck regulator while the input voltage is sufficiently greater than the regulated output voltage and gradually transitions to the buck-boost mode as the input voltage approaches the output. This dual mode approach maintains regulation over a wide range of input voltages with optimal conversion efficiency in the buck mode and a glitch-free output during mode transitions. This easy to use controller includes drivers for the high side buck MOSFET and the low side boost MOSFET. The regulators control method is based upon current mode control utilizing an emulated current ramp. Emulated current mode control reduces noise sensitivity of the pulse-width modulation circuit, allowing reliable control of the very small duty cycles necessary in high input voltage applications. Additional protection features include current limit, thermal shutdown and an enable input. The device is available in a power enhanced HTSSOP-20 package featuring an exposed die attach pad to aid thermal dissipation. 1 2 • • • • • • • • • • • • LM5118-Q1 is an Automotive Grade product that is AEC-Q100 grade 1 qualified (-40°C to 125°C operating junction temperature) Ultra-wide input voltage range from 3V to 75V Emulated peak current mode control Smooth transition between step-down and step- up modes Switching frequency programmable to 500KHz Oscillator synchronization capability Internal high voltage bias regulator Integrated high and low-side gate drivers Programmable soft-start time Ultra low shutdown current Enable input wide bandwidth error amplifier 1.5% feedback reference accuracy Thermal shutdown PACKAGE • HTSSOP-20 (Exposed pad) 1 2 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. All trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 2008–2013, Texas Instruments Incorporated LM5118, LM5118-Q1 SNVS566G – APRIL 2008 – REVISED FEBRUARY 2013 www.ti.com Typical Application Circuit VIN VCC HB LM5118 HO VOUT HS SS CS RAMP CSG LO RT VOUT FB GND 2 Submit Documentation Feedback COMP Copyright © 2008–2013, Texas Instruments Incorporated Product Folder Links: LM5118 LM5118-Q1 LM5118, LM5118-Q1 www.ti.com SNVS566G – APRIL 2008 – REVISED FEBRUARY 2013 Package HTSSOP-20 (Exposed pad) Connection Diagram 1 20 HS UVLO VIN 2 19 HO RT 3 18 HB EN 4 17 VCCX RAMP 5 16 VCC AGND 6 15 LO SS 7 14 PGND FB 8 13 CSG COMP 9 12 CS VOUT 10 11 SYNC Figure 1. PWP0020A Package (Top View) Copyright © 2008–2013, Texas Instruments Incorporated Product Folder Links: LM5118 LM5118-Q1 Submit Documentation Feedback 3 LM5118, LM5118-Q1 SNVS566G – APRIL 2008 – REVISED FEBRUARY 2013 www.ti.com PIN DESCRIPTIONS Pin Name Description 1 VIN 2 UVLO Input supply voltage. 3 RT The internal oscillator frequency is set with a single resistor between this pin and the AGND pin. The recommended frequency range is 50 kHz to 500 kHz. 4 EN If the EN pin is below 0.5V, the regulator will be in a low power state drawing less than 10 µA from VIN. EN must be raised above 3V for normal operation. 5 RAMP Ramp control signal. An external capacitor connected between this pin and the AGND pin sets the ramp slope used for emulated current mode control. 6 AGND Analog ground. 7 SS Soft-Start. An external capacitor and an internal 10 µA current source set the rise time of the error amp reference. The SS pin is held low when VCC is less than the VCC under-voltage threshold (< 3.7V), when the UVLO pin is low (< 1.23V), when EN is low (< 0.5V) or when thermal shutdown is active. 8 FB Feedback signal from the regulated output. Connect to the inverting input of the internal error amplifier. 9 COMP Output of the internal error amplifier. The loop compensation network should be connected between COMP and the FB pin. 10 VOUT Output voltage monitor for emulated current mode control. Connect this pin directly to the regulated output. 11 SYNC Sync input for switching regulator synchronization to an external clock. 12 CS If the UVLO pin is below 1.23V, the regulator will be in standby mode (VCC regulator running, switching regulator disabled). When the UVLO pin exceeds 1.23V, the regulator enters the normal operating mode. An external voltage divider can be used to set an under-voltage shutdown threshold. A fixed 5 µA current is sourced out of the UVLO pin. If a current limit condition exists for 256 consecutive switching cycles, an internal switch pulls the UVLO pin to ground and then releases. Current sense input. Connect to the diode side of the current sense resistor. 13 CSG 14 PGND Current sense ground input. Connect to the ground side of the current sense resistor. 15 LO 16 VCC 17 VCCX 18 HB High side gate driver supply used in bootstrap operation. The bootstrap capacitor supplies current to charge the high side MOSFET gate. This capacitor should be placed as close to the controller as possible and connected between HB and HS. 19 HO Buck MOSFET gate drive output. Connect to the gate of the high side buck MOSFET through a short, low inductance path. 20 HS Buck MOSFET source pin. Connect to the source terminal of the high side buck MOSFET and the bootstrap capacitor. EP Solder to the ground plane under the IC to aid in heat dissipation. Power Ground. Boost MOSFET gate drive output. Connect to the gate of the external boost MOSFET. Output of the bias regulator. Locally decouple to PGND using a low ESR/ESL capacitor located as close to the controller as possible. Optional input for an externally supplied bias supply. If the voltage at the VCCX pin is greater than 3.9V, the internal VCC regulator is disabled and the VCC pin is internally connected to VCCX pin supply. If VCCX is not used, connect to AGND. These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. 4 Submit Documentation Feedback Copyright © 2008–2013, Texas Instruments Incorporated Product Folder Links: LM5118 LM5118-Q1 LM5118, LM5118-Q1 www.ti.com SNVS566G – APRIL 2008 – REVISED FEBRUARY 2013 Absolute Maximum Ratings (1) VIN, EN, VOUT to GND -0.3V to 76V VCC, LO, VCCX, UVLO to GND (2) -0.3 to 15V HB to HS -0.3 to 15V HO to HS -0.3 to HB+0.3V HS to GND -4V to 76V CSG, CS to GND -0.3V to +0.3V RAMP, SS, COMP, FB, SYNC, RT to GND -0.3 to 7V ESD Rating HBM (3) 2 kV Storage Temperature Range -55°C to +150°C Junction Temperature (1) (2) (3) Absolute Maximum Ratings are limits beyond which damage to the device may occur. These pins must not be raised above VIN. The human body model is a 100pF capacitor discharged through a 1.5 kΩ resistor into each pin. Operating Ratings VIN +150°C (1) (2) 3V to 75V VCC, VCCX 4.75V to 14V Junction Temperature (1) (2) -40°C to +125°C Operating Ratings indicate conditions for which the device is intended to be functional, but does not ensure specific performance limits. For specifications and test conditions see Electrical Characteristics. 5V VIN is required to initially start the controller. Copyright © 2008–2013, Texas Instruments Incorporated Product Folder Links: LM5118 LM5118-Q1 Submit Documentation Feedback 5 LM5118, LM5118-Q1 SNVS566G – APRIL 2008 – REVISED FEBRUARY 2013 www.ti.com Electrical Characteristics Limits in standard type are for TJ = 25°C only; limits in boldface type apply over the junction temperature range of -40°C to +125°C. Unless otherwise specified, the following conditions apply: VIN = 48V, VCCX = 0V, EN = 5V, RT = 29.11 kΩ, No load on LO and HO (1). Symbol Parameter Conditions IBIAS VIN Operating Current IBIASX ISTDBY Min Typ Max Units VCCX = 0V 4.5 5.5 mA VIN Operating Current VCCX = 5V 1 1.85 mA VIN Shutdown Current EN = 0V 1 10 µA VCC(REG) VCC Regulation VCCX = 0V 6.8 7 7.2 V VCC(REG) VCC Regulation VCCX = 0V, VIN = 6V 5 5.25 5.5 VCC Sourcing Current Limit VCC = 0 21 35 VCCX Switch threshold VCCX Rising 3.68 3.85 VIN SUPPLY VCC REGULATOR VCCX Switch hysteresis ICCX = 10 mA VCCX Switch Leakage VCCX = 0V VCCCX Pull-down Resistance VCCX = 3V V 5 12 Ω 0.5 1 µA V 70 VCC Under-Voltage Lockout Voltage VCC Rising 3.52 VCC Under-Voltage Hysteresis HB DC Bias current 4.02 0.2 VCCX Switch RDS(ON) 3.7 kΩ 3.86 0.21 HB-HS = 15V 205 VC LDO Mode Turn-off V mA V V 260 10 µA V EN INPUT VIL max EN Input Low Threshold VIH EN Input High Threshold min 0.5 V 3.00 V EN Input Bias Current VEN = 3V -1 1 µA EN Input Bias Current VEN = 0.5V -1 1 µA EN Input Bias Current VEN = 75V UVLO Standby Threshold UVLO Rising 50 µA UVLO THRESHOLDS 1.191 UVLO Threshold Hysteresis UVLO Pull-up Current Source UVLO = 0V UVLO Pull-down RDS(ON) 1.231 1.271 V 0.105 V 5 µA 100 200 10.5 13.5 Ω SOFT- START SS Current Source SS = 0V SS to FB Offset FB = 1.23V 7.5 SS Output Low Voltage Sinking 100 µA, UVLO = 0V FB Reference Voltage Measured at FB pin, FB = COMP FB Input Bias Current FB = 2V µA 150 mV 7 mV ERROR AMPLIFIER VREF 1.212 COMP Sink/Source Current 1.230 1.248 V 20 200 nA 3 mA AOL DC Gain 80 dB fBW Unity Bain Bandwidth 3 MHz PWM COMPARATORS (1) 6 tHO(OFF) Forced HO Off-time TON(MIN) Minimum HO On-time 305 400 70 495 ns ns COMP to Comparator Offset 200 mV Min and Max limits are 100% production tested at 25°C. Limits over the operating temperature range are ensured through correlation using Statistical Quality Control (SQC) methods. Limits are used to calculate Average Outgoing Quality Level (AOQL). Submit Documentation Feedback Copyright © 2008–2013, Texas Instruments Incorporated Product Folder Links: LM5118 LM5118-Q1 LM5118, LM5118-Q1 www.ti.com SNVS566G – APRIL 2008 – REVISED FEBRUARY 2013 Electrical Characteristics (continued) Limits in standard type are for TJ = 25°C only; limits in boldface type apply over the junction temperature range of -40°C to +125°C. Unless otherwise specified, the following conditions apply: VIN = 48V, VCCX = 0V, EN = 5V, RT = 29.11 kΩ, No load on LO and HO (1). Symbol Parameter Conditions Min Typ Max Units fSW1 Frequency 1 RT = 29.11 kΩ 178 200 224 kHz fSW2 Frequency 2 RT = 9.525 kΩ 450 515 575 kHz OSCILLATOR (RT PIN) SYNC Sync threshold falling 1.3 V CURRENT LIMIT VCS(TH) Cycle-by-cycle Sense Voltage Threshold (CS-CSG) RAMP = 0 Buck Mode -103 -125 -147 mV VCS(THX) Cycle-by-cycle Sense Voltage Threshold (CS-CSG) RAMP = 0 Buck-Boost Mode -218 -255 -300 mV CS Bias Current CS = 0V 45 60 µA CSG Bias Current CSG = 0V 45 60 µA Current Limit Fault Timer 256 cycles RAMP GENERATOR IR1 RAMP Current 1 VIN = 60V, VOUT = 10V 245 305 365 µA IR2 RAMP Current 2 VIN = 12V, VOUT = 12V 95 115 135 µA IR3 RAMP Current 3 VIN = 5V, VOUT = 12V 65 80 95 µA VOUT Bias Current VOUT = 48V 245 µA LOW SIDE (LO) GATE DRIVER VOLL LO Low-state Output Voltage ILO = 100 mA VOHL LO High-state Output Voltage ILO = -100 mA VOHL = VCC-VLO 0.095 LO Rise Time C-load = 1 nF, VCC = 8V 0.14 0.23 V 0.25 V 16 ns LO Fall Time C-load = 1 nF, VCC = 8V 14 ns IOHL Peak LO Source Current VLO = 0V, VCC = 8V 2.2 A IOLL Peak LO Sink Current VLO = VCC = 8V 2.7 A HIGH SIDE (HO) GATE DRIVER VOLH HO Low-state Output Voltage IHO = 100 mA VOHH HO High-state Output Voltage IHO = -100 mA, VOHH = VHB-VOH HO Rise Time HO Fall Time IOHH IOLH 0.1 0.135 0.21 V 0.25 V C-load = 1 nF, VCC = 8V 14 ns C-load = 1 nF, VCC = 8V 12 ns Peak HO Source Current VHO = 0V, VCC = 8V 2.2 A Peak HO Sink Current VHO = VCC = 8V 3.5 A 3 V HB-HS Under Voltage Lock-out BUCK-BOOST CHARACTERISTICS Buck-Boost Mode Buck Duty Cycle (2) 69 75 80 % THERMAL TSD (2) Thermal Shutdown Temp. 165 °C Thermal Shutdown Hysteresis 25 °C θJA Junction to Ambient 40 °C/W θJC Junction to Case 4 °C/W When the duty cycle exceeds 75%, the LM5118 controller gradually phases into the Buck-Boost mode. Copyright © 2008–2013, Texas Instruments Incorporated Product Folder Links: LM5118 LM5118-Q1 Submit Documentation Feedback 7 LM5118, LM5118-Q1 SNVS566G – APRIL 2008 – REVISED FEBRUARY 2013 www.ti.com Typical Performance Characteristics Efficiency vs VIN and IOUT VOUT = 12V 100 90 3 AMP x 85 CURRENT LIMIT THRESHOLD (mV) x EFFICIENCY (%) -100 xxx xx 95 x 1 AMP x 2 AMP x 80 75 Current Limit Threshold vs VOUT/VIN VOUT = 12V 0 x 10 20 30 40 50 60 -125 -150 -175 -200 -225 -250 -275 65 70 70 75 VIN (V) 85 Figure 3. VCC vs VIN VCC vs IVCC 10 8 8 6 6 VCC (V) 10 4 2 4 2 0 0 0 2 4 6 8 10 12 0 10 20 VIN (V) 50 IVCC (mA) Error Amplifier Gain/Phase LO and HO Peak Gate Current vs Output Voltage VCC = 8V 50 150 4 40 120 3.5 30 90 60 10 30 CURRENT (A) 20 HO Sink 2.5 LO Sink 2 1.5 LO Source 1 0 0 -10 1E+04 40 Figure 5. PHASE (°) GAIN (dB) 30 Figure 4. 3 1E+05 1E+06 -30 1E+07 HO Source 0.5 0 0 1 FREQUENCY (Hz) Submit Documentation Feedback 2 3 4 5 6 7 8 OUTPUT VOLTAGE (V) Figure 6. 8 95 100 105 110 90 VOUT/VIN DC (%) Figure 2. VCC (V) 80 Figure 7. Copyright © 2008–2013, Texas Instruments Incorporated Product Folder Links: LM5118 LM5118-Q1 LM5118, LM5118-Q1 www.ti.com SNVS566G – APRIL 2008 – REVISED FEBRUARY 2013 Typical Performance Characteristics (continued) Oscillator Frequency vs RT 600 500 FOSC (kHz) 400 300 200 100 0 0 20 40 60 80 100 120 140 160 RT (k:) Figure 8. Copyright © 2008–2013, Texas Instruments Incorporated Product Folder Links: LM5118 LM5118-Q1 Submit Documentation Feedback 9 LM5118, LM5118-Q1 SNVS566G – APRIL 2008 – REVISED FEBRUARY 2013 www.ti.com BLOCK DIAGRAM AND TYPICAL APPLICATION CIRCUIT 17 LM5118 Vin (4V - 75V ) VIN 1 VCCX 7V VIN VCC 16 REGULATOR VCC UVLO R8 C8 C2 C1 4 EN 3.9V 3V 5 PA THERMAL SHUTDOWN SHUTDOWN AND STANDBY MODE CONTROL R1 HB 18 C13 HB UVLO 2 DISABLE UVLO R2 C12 1.23V Vin HICCUP MODE FAULT TIMER 10 PA 7 SS Q1 CLK 5V PWM C4 S Q R Q HO 19 HS 20 L1 LEVEL SHIFT D2 VOUT 1.23V I-LIMIT 8 FB ERROR AMP C5 C6 C11 Vth ( buck) = 1.25V Vth ( buck - boost ) = 2.50V + R4 9 10 Rs V/A C9 R7 CS 12 TRACK and HOLD C10 D1 CLK A=10 Rs CSG 13 COMP R5 VOUT 10 Vin 11 SYNC RAMP GENERATOR OSCILLATOR 3 RT LO IRAMP (buck-boost) = 5 PA x Vin + 50 PA AGND 5 RAMP Q2 IRAMP (buck) = ( 5 PA x ( Vin - Vout )) + 50 PA CLK R3 15 R6 IRAMP 6 14 BUCK-BOOST MODE CONTROL PGND C3 Figure 9. 10 Submit Documentation Feedback Copyright © 2008–2013, Texas Instruments Incorporated Product Folder Links: LM5118 LM5118-Q1 LM5118, LM5118-Q1 www.ti.com SNVS566G – APRIL 2008 – REVISED FEBRUARY 2013 DETAILED OPERATING DESCRIPTION The LM5118 high voltage switching regulator features all of the functions necessary to implement an efficient high voltage buck or buck-boost regulator using a minimum of external components. The regulator switches smoothly from buck to buck-boost operation as the input voltage approaches the output voltage, allowing operation with the input greater than or less than the output voltage. This easy to use regulator integrates highside and low-side MOSFET drivers capable of supplying peak currents of 2 Amps. The regulator control method is based on current mode control utilizing an emulated current ramp. Peak current mode control provides inherent line feed-forward, cycle-by-cycle current limiting and ease of loop compensation. The use of an emulated control ramp reduces noise sensitivity of the pulse-width modulation circuit, allowing reliable processing of very small duty cycles necessary in high input voltage applications. The operating frequency is user programmable from 50 kHz to 500 kHz. An oscillator synchronization pin allows multiple LM5118 regulators to self synchronize or be synchronized to an external clock. Fault protection features include current limiting, thermal shutdown and remote shutdown capability. An under-voltage lockout input allows regulator shutdown when the input voltage is below a user selected threshold, and a low state at the enable pin will put the regulator into an extremely low current shutdown state. The device is available in the HTSSOP-20EP package featuring an exposed pad to aid in thermal dissipation. A buck-boost regulator can maintain regulation for input voltages either higher or lower than the output voltage. The challenge is that buck-boost power converters are not as efficient as buck regulators. The LM5118 has been designed as a dual mode controller whereby the power converter acts as a buck regulator while the input voltage is above the output. As the input voltage approaches the output voltage, a gradual transition to the buck-boost mode occurs. The dual mode approach maintains regulation over a wide range of input voltages, while maintaining the optimal conversion efficiency in the normal buck mode. The gradual transition between modes eliminates disturbances at the output during transitions. Figure 10 shows the basic operation of the LM5118 regulator in the buck mode. In buck mode, transistor Q1 is active and Q2 is disabled. The inductor current ramps in proportion to the VIN - VOUT voltage difference when Q1 is active and ramps down through the recirculating diode D1 when Q1 is off. The first order buck mode transfer function is VOUT/VIN = D, where D is the duty cycle of the buck switch, Q1. VIN Buck Switch Current HB Q1 HO D2 VOUT HS D1 LM5118 Diode Current CS CSG Q2 (OFF) LO Figure 10. Buck Mode Operation Figure 11 shows the basic operation of buck-boost mode. In buck-boost mode both Q1 and Q2 are active for the same time interval each cycle. The inductor current ramps up (proportional to VIN) when Q1 and Q2 are active and ramps down through the recirculating diode during the off time. The first order buck-boost transfer function is VOUT/VIN = D/(1-D), where D is the duty cycle of Q1 and Q2. Copyright © 2008–2013, Texas Instruments Incorporated Product Folder Links: LM5118 LM5118-Q1 Submit Documentation Feedback 11 LM5118, LM5118-Q1 SNVS566G – APRIL 2008 – REVISED FEBRUARY 2013 www.ti.com VIN Buck Switch Current HB Q1 HO D2 VOUT HS D1 LM5118 Diode Current CS CSG Q2 LO Figure 11. Buck-Boost Mode Operation 100 90 70 60 50 40 30 DUTY CYCLE (%) 80 20 10 18 17 16 15 14 13 12 0 VIN (V) Figure 12. Mode Dependence on Duty Cycle (VOUT = 12V) 12 Submit Documentation Feedback Copyright © 2008–2013, Texas Instruments Incorporated Product Folder Links: LM5118 LM5118-Q1 LM5118, LM5118-Q1 www.ti.com SNVS566G – APRIL 2008 – REVISED FEBRUARY 2013 OPERATION MODES Figure 12 illustrates how duty cycle affects the operational mode and is useful for reference in the following discussions. Initially, only the buck switch is active and the buck duty cycle increases to maintain output regulation as VIN decreases. When VIN is approximately equal to 15.5V, the boost switch begins to operate with a low duty cycle. If VIN continues to fall, the boost switch duty cycle increases and the buck switch duty cycle decreases until they become equal at VIN = 13.2V. Buck Mode Operation: VIN > VOUT The LM5118 buck-boost regulator operates as a conventional buck regulator with emulated current mode control while VIN is greater than VOUT and the buck mode duty cycle is less than 75%. In buck mode, the LO gate drive output to the boost switch remains low. Buck-Boost Mode Operation: VIN ≊ VOUT When VIN decreases relative to VOUT, the duty cycle of the buck switch will increase to maintain regulation. Once the duty cycle reaches 75%, the boost switch starts to operate with a very small duty cycle. As VIN is further decreased, the boost switch duty cycle increases until it is the same as the buck switch. As VIN is further decreased below VOUT, the buck and boost switch operate together with the same duty cycle and the regulator is in full buck-boost mode. This feature allows the regulator to transition smoothly from buck to buck-boost mode. It should be noted that the regulator can be designed to operate with VIN less than 4 volts, but VIN must be at least 5 volts during start-up. Figure 13 presents a timing illustration of the gradual transition from buck to buckboost mode when the input voltage ramps downward over a few switching cycles. Figure 13. Buck (HO) and Boost (LO) Switch Duty Cycle vs. Time, Illustrating Gradual Mode Change with Decreasing Input Voltage Copyright © 2008–2013, Texas Instruments Incorporated Product Folder Links: LM5118 LM5118-Q1 Submit Documentation Feedback 13 LM5118, LM5118-Q1 SNVS566G – APRIL 2008 – REVISED FEBRUARY 2013 www.ti.com FUNCTIONAL DESCRIPTION High Voltage Start-Up Regulator The LM5118 contains a dual mode, high voltage linear regulator that provides the VCC bias supply for the PWM controller and the MOSFET gate driver. The VIN input pin can be connected directly to input voltages as high as 75V. For input voltages below 10V, an internal low dropout switch connects VCC directly to VIN. In this supply range, VCC is approximately equal to VIN. For VIN voltages greater than 10V, the low dropout switch is disabled and the VCC regulator is enabled to maintain VCC at approximately 7V. A wide operating range of 4V to 75V (with a startup requirement of at least 5 volts) is achieved through the use of this dual mode regulator. The output of the VCC regulator is current limited to 35 mA, typical. Upon power up, the regulator sources current into the capacitor connected to the VCC pin. When the voltage at the VCC pin exceeds the VCC undervoltage threshold of 3.7V and the UVLO input pin voltage is greater than 1.23V, the gate driver outputs are enabled and a soft-start sequence begins. The gate driver outputs remain enabled until VCC falls below 3.5V or the voltage at the UVLO pin falls below 1.13V. In many applications the regulated output voltage or an auxiliary supply voltage can be applied to the VCCX pin to reduce the IC power dissipation. For output voltages between 4V and 15V, VOUT can be connected directly to VCCX. When the voltage at the VCCX pin is greater than 3.85V, the internal VCC regulator is disabled and an internal switch connects VCCX to VCC, reducing the internal power dissipation. In high voltage applications extra care should be taken to ensure the VIN pin voltage does not exceed the absolute maximum voltage rating of 76V. During line or load transients, voltage ringing on the VIN line that exceeds the absolute maximum rating can damage the IC. Both careful PC board layout and the use of quality bypass capacitors located close to the VIN and GND pins are essential. Vin 10V 7V 3.7V Vcc 3.5V VIN and VCC Internal Enable Signal Figure 14. VIN and VCC Sequencing Enable The LM5118 contains an enable function which provides a very low input current shutdown mode. If the EN pin is pulled below 0.5V, the regulator enters shutdown mode, drawing less than 10 µA from the VIN pin. Raising the EN input above 3V returns the regulator to normal operation. The EN pin can be tied directly to the VIN pin if this function is not needed. It must not be left floating. A 1MΩ pull-up resistor to VIN can be used to interface with an open collector or open drain control signal. UVLO An under-voltage lockout pin is provided to disable the regulator when the input is below the desired operating range. If the UVLO pin is below 1.13V, the regulator enters a standby mode with the outputs disabled, but with VCC regulator operating. If the UVLO input exceeds 1.23V, the regulator will resume normal operation. A voltage divider from the input to ground can be used to set a VIN threshold to disable the regulator in brown-out conditions or for low input faults. 14 Submit Documentation Feedback Copyright © 2008–2013, Texas Instruments Incorporated Product Folder Links: LM5118 LM5118-Q1 LM5118, LM5118-Q1 www.ti.com SNVS566G – APRIL 2008 – REVISED FEBRUARY 2013 If a current limit fault exists for more than 256 clock cycles, the regulator will enter a “hiccup” mode of current limiting and the UVLO pin will be pulled low by an internal switch. This switch turns off when the UVLO pin approaches ground potential allowing the UVLO pin to rise. A capacitor connected to the UVLO pin will delay the return to a normal operating level and thereby set the off-time of the hiccup mode fault protection. An internal 5 µA pull-up current pulls the UVLO pin to a high state to ensure normal operation when the VIN UVLO function is not required and the pin is left floating. Oscillator and Sync Capability The LM5118 oscillator frequency is set by a single external resistor connected between the RT pin and the AGND pin. The RT resistor should be located very close to the device and connected directly to the pins of the IC. To set a desired oscillator frequency (f), the necessary value for the RT resistor can be calculated from the following equation: 9 RT = 6.4 x 10 3 - 3.02 x 10 f (1) The SYNC pin can be used to synchronize the internal oscillator to an external clock. The external clock must be of higher frequency than the free-running frequency set by the RT resistor. A clock circuit with an open drain output is the recommended interface from the external clock to the SYNC pin. The clock pulse duration should be greater than 15 ns. Multiple LM5118 devices can be synchronized together simply by connecting the SYNC pins together as shown in Figure 15. In this configuration all of the devices will be synchronized to the highest frequency device. Figure 16 illustrates the SYNC input/output features of the LM5118. The internal oscillator circuit drives the SYNC pin with a strong pull-down/weak pull-up inverter. When the SYNC pin is pulled low, either by the internal oscillator or an external clock, the ramp cycle of the oscillator is terminated and forced 400 ns off-time is initiated before a new oscillator cycle begins. If the SYNC pins of several LM5118 IC’s are connected together, the IC with the highest internal clock frequency will pull all the connected SYNC pins low and terminate the oscillator ramp cycles of the other IC’s. The LM5118 with the highest programmed clock frequency will serve as the master and control the switching frequency of all the devices with lower oscillator frequencies. SYNC 100 PA LM5118 I 1/RT SYNC 1.23V LM5118 SYNC UP TO FIVE LM5118 DEVICES Q S Q R DEADTIME ONE - SHOT Figure 15. Sync from Multiple Devices Figure 16. Simplified Oscillator and Block Diagram with Sync I/O Circuit Error Amplifier and PWM Comparator The internal high gain error amplifier generates an error signal proportional to the difference between the regulated output voltage and an internal precision reference (1.23V). The output of the error amplifier is connected to the COMP pin. Loop compensation components, typically a type II network illustrated in Figure 9 are connected between the COMP and FB pins. This network creates a low frequency pole, a zero, and a noise reducing high frequency pole. The PWM comparator compares the emulated current sense signal from the RAMP generator to the error amplifier output voltage at the COMP pin. The same error amplifier is used for operation in buck and buck-boost mode. Copyright © 2008–2013, Texas Instruments Incorporated Product Folder Links: LM5118 LM5118-Q1 Submit Documentation Feedback 15 LM5118, LM5118-Q1 SNVS566G – APRIL 2008 – REVISED FEBRUARY 2013 www.ti.com v Buck: ( 5 PA x ( Vin - Vout ) + 50 PA ) x Emulated Ramp Buck - Boost: ( 5 PA x Vin + 50 PA ) x ton Cramp ton Cramp Pedestal Level = 10 x Rs (volts/amp) t Ton Figure 17. Composition of Emulated Current Signal Ramp Generator The ramp signal of a pulse-width modulator with current mode control is typically derived directly from the buck switch drain current. This switch current corresponds to the positive slope portion of the inductor current signal. Using this signal for the PWM ramp simplifies the control loop transfer function to a single pole response and provides inherent input voltage feed-forward compensation. The disadvantage of using the buck switch current signal for PWM control is the large leading edge spike due to circuit parasitics. The leading edge spike must be filtered or blanked to avoid early termination of the PWM pulse. Also, the current measurement may introduce significant propagation delays. The filtering, blanking time and propagation delay limit the minimal achievable pulse width. In applications where the input voltage may be relatively large in comparison to the output voltage, controlling a small pulse width is necessary for regulation. The LM5118 utilizes a unique ramp generator which does not actually measure the buck switch current but instead creates a signal representing or emulating the inductor current. The emulated ramp provides signal to the PWM comparator that is free of leading edge spikes and measurement or filtering delays. The current reconstruction is comprised of two elements, a sample-andhold pedestal level and a ramp capacitor which is charged by a controlled current source. Refer to Figure 17 for details. The sample-and-hold pedestal level is derived from a measurement of the recirculating current through a current sense resistor in series with the recirculating diode of the buck regulator stage. A small value current sensing resistor is required between the recirculating diode anode and ground. The CS and CSG pins should be Kelvin connected directly to the sense resistor. The voltage level across the sense resistor is sampled and held just prior to the onset of the next conduction interval of the buck switch. The current sensing and sample-and-hold provide the DC level of the reconstructed current signal. The sample and hold of the recirculating diode current is valid for both buck and buck-boost modes. The positive slope inductor current ramp is emulated by an external capacitor connected from the RAMP pin to the AGND and an internal voltage controlled current source. In buck mode, the ramp current source that emulates the inductor current is a function of the VIN and VOUT voltages per the following equation: IRAMP (buck) = 5 PA x (VIN - VOUT) + 50 PA V (2) In buck-boost mode, the ramp current source is a function of the input voltage VIN, per the following equation: IRAMP (buck - boost) = 5 PA x VIN + 50 PA V (3) Proper selection of the RAMP capacitor (CRAMP) depends upon the value of the output inductor (L) and the current sense resistor (RS). For proper current emulation, the sample and hold pedestal value and the ramp amplitude must have the same relative relationship to the actual inductor current. That is: 16 Submit Documentation Feedback Copyright © 2008–2013, Texas Instruments Incorporated Product Folder Links: LM5118 LM5118-Q1 LM5118, LM5118-Q1 www.ti.com SNVS566G – APRIL 2008 – REVISED FEBRUARY 2013 RS x A = CRAMP = gm x L CRAMP gm x L A x RS where • • gm is the ramp generator transconductance (5 µA/V) A is the current sense amplifier gain (10V/V) (4) The ramp capacitor should be located very close to the device and connected directly to the RAMP and AGND pins. The relationship between the average inductor current and the pedestal value of the sampled inductor current can cause instability in certain operating conditions. This instability is known as sub-harmonic oscillation, which occurs when the inductor ripple current does not return to its initial value by the start of the next switching cycle. Sub-harmonic oscillation is normally characterized by observing alternating wide and narrow pulses at the switch node. Adding a fixed slope voltage ramp (slope compensation) to the current sense signal prevents this oscillation. The 50µA of offset current provided from the emulated current source adds enough slope compensation to the ramp signal for output voltages less than or equal to 12V. For higher output voltages, additional slope compensation may be required. In such applications, the ramp capacitor can be decreased from the nominal calculated value to increase the ramp slope compensation. The pedestal current sample is obtained from the current sense resistor (Rs) connected to the CS and CSG pins. It is sometimes helpful to adjust the internal current sense amplifier gain (A) to a lower value in order to obtain the higher current limit threshold. Adding a pair of external resistors RG in a series with CS and CSG as shown in Figure 18 reduces the current sense amplifier gain A according to the following equation: 10k A= 1k + RG (5) Copyright © 2008–2013, Texas Instruments Incorporated Product Folder Links: LM5118 LM5118-Q1 Submit Documentation Feedback 17 LM5118, LM5118-Q1 SNVS566G – APRIL 2008 – REVISED FEBRUARY 2013 www.ti.com Current Limit In the buck mode the average inductor current is equal to the output current (IOUT). In buck-boost mode the average inductor current is approximately equal to: Iout x 1 + VOUT VIN (6) Consequently, the inductor current in buck-boost mode is much larger especially when VOUT is large relative to VIN. The LM5118 provides a current monitoring scheme to protect the circuit from possible over-current conditions. When set correctly, the emulated current sense signal is proportional to the buck switch current with a scale factor determined by the current sense resistor. The emulated ramp signal is applied to the current limit comparator. If the peak of the emulated ramp signal exceeds 1.25V when operating in the buck mode, the PWM cycle is immediately terminated (cycle-by-cycle current limiting). In buck-boost mode the current limit threshold is increased to 2.50V to allow higher peak inductor current. To further protect the external switches during prolonged overload conditions, an internal counter detects consecutive cycles of current limiting. If the counter detects 256 consecutive current limited PWM cycles, the LM5118 enters a low power dissipation hiccup mode. In the hiccup mode, the output drivers are disabled, the UVLO pin is momentarily pulled low, and the soft-start capacitor is discharged. The regulator is restarted with a normal soft-start sequence once the UVLO pin charges back to 1.23V. The hiccup mode off-time can be programmed by an external capacitor connected from UVLO pin to ground. This hiccup cycle will repeat until the output overload condition is removed. In applications with low output inductance and high input voltage, the switch current may overshoot due to the propagation delay of the current limit comparator and control circuitry. If an overshoot should occur, the sampleand-hold circuit will detect the excess recirculating diode current. If the sample-and-hold pedestal level exceeds the internal current limit threshold, the buck switch will be disabled and will skip PWM cycles until the inductor current has decayed below the current limit threshold. This approach prevents current runaway conditions due to propagation delays or inductor saturation since the inductor current is forced to decay before the buck switch is turned on again. CURRENT LIMIT COMPARATOR CURRENT SENSE AMPLIFIER Vth TRACK and HOLD - 10k 1k CS RG + IRAMP 10k IL RS + 1k CSG RG 0.2V RAMP RESET RAMP CRAMP Figure 18. Current Limit and Ramp Circuit 18 Submit Documentation Feedback Copyright © 2008–2013, Texas Instruments Incorporated Product Folder Links: LM5118 LM5118-Q1 LM5118, LM5118-Q1 www.ti.com SNVS566G – APRIL 2008 – REVISED FEBRUARY 2013 Maximum Duty Cycle Each conduction cycle of the buck switch is followed by a forced minimum off-time of 400ns to allow sufficient time for the recirculating diode current to be sampled. This forced off-time limits the maximum duty cycle of the controller. The actual maximum duty cycle will vary with the operating frequency as follows: DMAX = 1 - f x 400 x 10-9 where • f is the oscillator frequency in Hz (7) 1 MAX DUTY CYCLE 0.95 0.9 0.85 0.8 0.75 0 100 200 300 400 500 600 FREQUENCY (kHz) Figure 19. Maximum Duty Cycle vs Frequency Limiting the maximum duty cycle will limit the maximum boost ratio (VOUT/VIN) while operating in buck-boost mode. For example, from Figure 19, at an operating frequency of 500 kHz, DMAX is 80%. Using the buck-boost transfer function. Vout D= Vin + Vout (8) With D= 80%, solving for VOUT results in, VOUT = 4 x VIN With a minimum input voltage of 5 volts, the maximum possible output voltage is 20 volts at f = 500 kHz. The buck-boost step-up ratio can be increased by reducing the operating frequency which increases the maximum duty cycle. Soft-Start The soft-start feature allows the regulator to gradually reach the initial steady state operating point, thus reducing start-up stresses and surges. The internal 10 µA soft-start current source gradually charges an external soft-start capacitor connected to the SS pin. The SS pin is connected to the positive input of the internal error amplifier. The error amplifier controls the pulse-width modulator such that the FB pin approximately equals the SS pin as the SS capacitor is charged. Once the SS pin voltage exceeds the internal 1.23V reference voltage, the error amp is controlled by the reference instead of the SS pin. The SS pin voltage is clamped by an internal amplifier at a level of 150 mV above the FB pin voltage. This feature provides a soft-start controlled recovery in the event a severe overload pulls the output voltage (and FB pin) well below normal regulation but doesn’t persist for 256 clock cycles. Various sequencing and tracking schemes can be implemented using external circuits that limit or clamp the voltage level of the SS pin. The SS pin acts as a non-inverting input to the error amplifier anytime SS voltage is less than the 1.23V reference. In the event a fault is detected (over-temperature, VCC under-voltage, hiccup current limit), the soft-start capacitor will be discharged. When the fault condition is no longer present, a new softstart sequence will begin. Copyright © 2008–2013, Texas Instruments Incorporated Product Folder Links: LM5118 LM5118-Q1 Submit Documentation Feedback 19 LM5118, LM5118-Q1 SNVS566G – APRIL 2008 – REVISED FEBRUARY 2013 www.ti.com HO Output The LM5118 contains a high side, high current gate driver and associated high voltage level shift. This gate driver circuit works in conjunction with an internal diode and an external bootstrap capacitor. A 0.1 µF ceramic capacitor, connected with short traces between the HB pin and HS pin is recommended for most circuit configurations. The size of the bootstrap capacitor depends on the gate charge of the external FET. During the off time of the buck switch, the HS pin voltage is approximately -0.5V and the bootstrap capacitor is charged from VCC through the internal bootstrap diode. When operating with a high PWM duty cycle, the buck switch will be forced off each cycle for 400ns to ensure that the bootstrap capacitor is recharged. Thermal Protection Internal Thermal Shutdown circuitry is provided to protect the integrated circuit in the event the maximum junction temperature is exceeded. When activated, typically at 165°C, the controller is forced into a low power reset state, disabling the output driver and the bias regulator. This protection is provided to prevent catastrophic failures from accidental device overheating. 20 Submit Documentation Feedback Copyright © 2008–2013, Texas Instruments Incorporated Product Folder Links: LM5118 LM5118-Q1 LM5118, LM5118-Q1 www.ti.com SNVS566G – APRIL 2008 – REVISED FEBRUARY 2013 APPLICATION INFORMATION The procedure for calculating the external components is illustrated with the following design example. The designations used in the design example correlate to the final schematic shown in Figure 26. The design specifications are: • VOUT = 12V • VIN = 5V to 75V • F = 300 kHz • Minimum load current (CCM operation) = 600 mA • Maximum load current = 3A R7 = RT RT sets the oscillator switching frequency. Generally speaking, higher operating frequency applications will use smaller components, but have higher switching losses. An operating frequency of 300 kHz was selected for this example as a reasonable compromise for both component size and efficiency. The value of RT can be calculated as follows: 9 RT = 6.4 x 10 3 - 3.02 x 10 f (9) therefore, R7 = 18.3 kΩ Ipk+ L1 Current Io Buck Iripple Io/(1-D) B-B Ipk- Iripple 1/Fs Figure 20. Inductor Current Waveform INDUCTOR SELECTION L1 The inductor value is determined based upon the operating frequency, load current, ripple current and the input and output voltages. Refer to Figure 20 for details. To keep the circuit in continuous conduction mode (CCM), the maximum ripple current IRIPPLE should be less than twice the minimum load current. For the specified minimum load of 0.6A, The maximum ripple current is 1.2A p-p. Also, the minimum value of L must be calculated both for a buck and buck-boost configurations. The final value of inductance will generally be a compromise between the two modes. It is desirable to have a larger value inductor for buck mode, but the saturation current rating for the inductor must be large for buck-boost mode, resulting in a physically large inductor. Additionally, large value inductors present buck-boost mode loop compensation challenges which will be discussed in the Error Amplifier Configuration section. For the design example, the inductor values in both modes are calculated as: Copyright © 2008–2013, Texas Instruments Incorporated Product Folder Links: LM5118 LM5118-Q1 Submit Documentation Feedback 21 LM5118, LM5118-Q1 SNVS566G – APRIL 2008 – REVISED FEBRUARY 2013 L1 = www.ti.com VOUT (VIN1 - VOUT) Buck Mode VIN1 x f x IRIPPLE VIN2 (VOUT) L1 = (VOUT + VIN2) x f x IRIPPLE Buck-Boost Mode where • • • • • • VOUT is the output voltage VIN1 is the maximum input voltage f is the switching frequency IRIPPLE is the selected inductor peak to peak ripple current (1.2 A selected for this example) VIN2 is the minimum input voltage (10) The resulting inductor values are: L1 = 28 µH, Buck Mode L1 = 9.8 µH Buck-Boost mode A 10 µH inductor was selected which is a compromise between these values, while favoring the buck-boost mode. As will be illustrated in the compensation section below, the inductor value should be as low as possible to move the buck-boost right-half-plane zero to a higher frequency. The ripple current is then rechecked with the selected inductor value using the equations above, IRIPPLE(BUCK) = 3.36A IRIPPLE(BUCK-BOOST) = 1.17A Because the inductor selected is lower than calculated for the Buck mode, the minimum load current for CCM in buck mode is 1.68 A at maximum VIN. With a 10 µH inductor, the worst case peak inductor currents can be estimated for each case, assuming a 20% inductor value tolerance. IOUT IRIPPLE Buck Mode + I1(PEAK) = 2 0.8 I2(PEAK) = (VOUT + Vin)IOUT 0.8 x VIN2 + IRIPPLE 2 Buck-Boost Mode (11) For this example, the two equations yield: I1(PEAK) = 5.43A I2(PEAK) = 13.34A An acceptable current limit setting would be 6.7A for buck mode since the LM5118 automatically doubles the current limit threshold in buck-boost mode. The selected inductor must have a saturation current rating at least as high as the buck-boost mode cycle-by-cycle current limit threshold, in this case at least 13.5A. A 10 µH 15 amp inductor was chosen for this application. R13 = RSENSE To select the current sense resistor value, begin by calculating the value of RSENSE for both modes of operation. 1.25V R13(BUCK) = 10 x IPEAK (12) R13(BUCK) = 23 mΩ For the buck-boost mode, RSENSE is given by: 22 Submit Documentation Feedback Copyright © 2008–2013, Texas Instruments Incorporated Product Folder Links: LM5118 LM5118-Q1 LM5118, LM5118-Q1 www.ti.com SNVS566G – APRIL 2008 – REVISED FEBRUARY 2013 R13(BUCK-BOOST) = 2.5V 10 x IPEAK (13) R13(BUCK-BOOST) = 18.7 mΩ A RSENSE value of no more than 18.7 mΩ must be used to ensure the required maximum output current in the buck-boost mode. A value of 15 mΩ was selected for component tolerances and is a standard value. R13 = 15 mΩ C15 = CRAMP With the inductor value selected, the value of C3 necessary for the emulation ramp circuit is: -6 C15 = CRAMP = L x 10 2 x RSENSE (14) With the inductance value (L1) selected as 10 µH, the calculated value for CRAMP is 333 pF. A standard value of 330 pF was selected. C9 - C12 = OUTPUT CAPACITORS In buck-boost mode, the output capacitors C9 - C12 must supply the entire output current during the switch ontime. For this reason, the output capacitors are chosen for operation in buck-boost mode, the demands being much less in buck operation. Both bulk capacitance and ESR must be considered to ensure a given output ripple voltage. Buck-boost mode capacitance can be estimated from: CMIN = IOUT x DMAX f x 'VOUT With DMAX = VOUT VIN2 + VOUT (15) ESR requirements can be estimated from: 'VOUT ESRMAX = IPEAK (16) For this example, with a ΔVOUT (output ripple) of 50 mV, CMIN = 141 µF ESRMAX = 3.8 mΩ If hold-up times are a consideration, the values of input/output capacitors must be increased appropriately. Note that it is usually advantageous to use multiple capacitors in parallel to achieve the ESR value required. Also, it is good practice to put a .1 µF - .47 µF ceramic capacitor directly on the output pins of the supply to reduce high frequency noise. Ceramic capacitors have good ESR characteristics, and are a good choice for input and output capacitors. It should be noted that the effective capacitance of ceramic capacitors decreases with dc bias. For larger bulk values of capacitance, a low ESR electrolytic is usually used. However, electrolytic capacitors have poor tolerance, especially over temperature, and the selected value should be selected larger than the calculated value to allow for temperature variation. Allowing for component tolerances, the following values of COUT were chosen for this design example: Two 180 µF Oscon electrolytic capacitors for bulk capacitance Two 47 µF ceramic capacitors to reduce ESR Two 0.47 µF ceramic capacitors to reduce spikes at the output . D1 Reverse recovery currents degrade performance and decrease efficiency. For these reasons, a Schottky diode of appropriate ratings should be used for D1. The voltage rating of the boost diode should be equal to VOUT plus some margin. Since D1 only conducts during the buck switch off time in either mode, the current rating required is: IDIODE = IOUT x (1-D) Buck Mode IDIODE = IOUT Buck-Boost Mode (17) (18) Copyright © 2008–2013, Texas Instruments Incorporated Product Folder Links: LM5118 LM5118-Q1 Submit Documentation Feedback 23 LM5118, LM5118-Q1 SNVS566G – APRIL 2008 – REVISED FEBRUARY 2013 www.ti.com D4 A Schottky type recirculating diode is required for all LM5118 applications. The near ideal reverse recovery characteristics and low forward voltage drop are particularly important diode characteristics for high input voltage and low output voltage applications. The reverse recovery characteristic determines how long the current surge lasts each cycle when the buck switch is turned on. The reverse recovery characteristics of Schottky diodes minimize the peak instantaneous power in the buck switch during the turn-on transition. The reverse breakdown rating of the diode should be selected for the maximum VIN plus some safety margin. The forward voltage drop has a significant impact on the conversion efficiency, especially for applications with a low output voltage. “Rated” current for diodes vary widely from various manufacturers. For the LM5118 this current is user selectable through the current sense resistor value. Assuming a worst case 0.6V drop across the diode, the maximum diode power dissipation can be high. The diode should have a voltage rating of VIN and a current rating of IOUT. A conservative design would at least double the advertised diode rating since specifications between manufacturers vary. For the reference design a 100V, 10A Schottky in a D2PAK package was selected. C1 - C5 = INPUT CAPACITORS A typical regulator supply voltage has a large source impedance at the switching frequency. Good quality input capacitors are necessary to limit the ripple voltage at the VIN pin while supplying most of the switch current during the buck switch on-time. When the buck switch turns on, the current into the buck switch steps from zero to the lower peak of the inductor current waveform, then ramps up to the peak value, and then drops to the zero at turn-off. The RMS current rating of the input capacitors depends on which mode of operation is most critical. IRMS(BUCK) = IOUT D(1 -D) (19) This value is a maximum at 50% duty cycle which corresponds to VIN = 24 volts. IRMS(BUCK-BOOST) = IOUT D(1 -D) 1-D (20) Checking both modes of operation we find: IRMS(BUCK) = 1.5 Amps IRMS(BUCK-BOOST) = 4.7 Amps Therefore C1-C5 should be sized to handle 4.7A of ripple current. Quality ceramic capacitors with a low ESR should be selected. To allow for capacitor tolerances, four 2.2 µF, 100V ceramic capacitors will be used. If step input voltage transients are expected near the maximum rating of the LM5118, a careful evaluation of the ringing and possible spikes at the device VIN pin should be completed. An additional damping network or input voltage clamp may be required in these cases. C20 The capacitor at the VCC pin provides noise filtering and stability for the VCC regulator. The recommended value of C20 should be no smaller than 0.1 µF, and should be a good quality, low ESR, ceramic capacitor. A value of 1 µF was selected for this design. C20 should be 10 x C8. If operating without VCCX, then fOSC x (QCBuck + Boost) + ILOAD(INTERNAL) (21) must be less than the VCC current limit. C8 The bootstrap capacitor between the HB and HS pins supplies the gate current to charge the buck switch gate at turn-on. The recommended value of C8 is 0.1 µF to 0.47 µF, and should be a good quality, low ESR, ceramic capacitor. A value of 0.1 µF was chosen for this design. 24 Submit Documentation Feedback Copyright © 2008–2013, Texas Instruments Incorporated Product Folder Links: LM5118 LM5118-Q1 LM5118, LM5118-Q1 www.ti.com SNVS566G – APRIL 2008 – REVISED FEBRUARY 2013 C16 = CSS The capacitor at the SS pin determines the soft-start time, i.e. the time for the reference voltage and the output voltage, to reach the final regulated value. The time is determined from: tSS = C16 x 1.23V 10 PA (22) and assumes a current limit>Iload + ICout For this application, a C16 value of 0.1 µF was chosen which corresponds to a soft-start time of about 12 ms. R8, R9 R8 and R9 set the output voltage level, the ratio of these resistors is calculated from: R8 VOUT - 1 = R9 1.23V (23) For a 12V output, the R8/R9 ratio calculates to 9.76. The resistors should be chosen from standard value resistors and a good starting point is to select resistors within power ratings appropriate for the output voltage. Values of 309Ω for R9 and 2.67 kΩ for R8 were selected. R1, R3, C21 A voltage divider can be connected to the UVLO pin to set a minimum operating voltage VIN(UVLO) for the regulator. If this feature is required, the easiest approach to select the divider resistor values is to choose a value for R1 between 10 kΩ and 100 kΩ, while observing the minimum value of R1 necessary to allow the UVLO switch to pull the UVLO pin low. This value is: R1 ≥ 1000 x VIN(MAX) R1 ≥ 75k in our example R3 is then calculated from R3 = 1.23 x R1 VIN(MIN) + 5 PA x R1 - 1.23 (24) Since VIN(MIN) for our example is 5V, set VIN(UVLO) to 4.0V for some margin in component tolerances and input ripple. R1 = 75k is chosen since it is a standard value R3 = 29.332k is calculated from the equation above. 29.4k was used since it is a standard value. Capacitor C21 provides filtering for the divider and the off time of the “hiccup” duty cycle during current limit. The voltage at the UVLO pin should never exceed 15V when using an external set-point divider. It may be necessary to clamp the UVLO pin at high input voltages. Knowing the desired off time during “hiccup” current limit, the value of C21 is given by: tOFF = - 1.23 x (R1 + R3) R1 x R3 x C21 x ln 1R1 + R3 VIN x R1 (25) Notice that tOFF varies with VIN In this example, C21 was chosen to be 0.1 µF. This will set the tOFF time to 956 µs with VIN = 12V. R2 A 1M pull-up resistor connected from the EN pin to the VIN pin is sufficient to keep enable in a high state if on-off control is not used. Copyright © 2008–2013, Texas Instruments Incorporated Product Folder Links: LM5118 LM5118-Q1 Submit Documentation Feedback 25 LM5118, LM5118-Q1 SNVS566G – APRIL 2008 – REVISED FEBRUARY 2013 www.ti.com SNUBBER A snubber network across the buck recirculating diode reduces ringing and spikes at the switching node. Excessive ringing and spikes can cause erratic operation and increase noise at the regulator output. In the limit, spikes beyond the maximum voltage rating of the LM5118 or the recirculating diode can damage these devices. Selecting the values for the snubber is best accomplished through empirical methods. First, make sure the lead lengths for the snubber connections are very short. Start with a resistor value between 5 and 20 Ohms. Increasing the value of the snubber capacitor results in more damping, however the snubber losses increase. Select a minimum value of the capacitor that provides adequate clamping of the diode waveform at maximum load. A snubber may be required for the boost diode as well. The same empirical procedure applies. Snubbers were not necessary in this example. 26 Submit Documentation Feedback Copyright © 2008–2013, Texas Instruments Incorporated Product Folder Links: LM5118 LM5118-Q1 LM5118, LM5118-Q1 www.ti.com SNVS566G – APRIL 2008 – REVISED FEBRUARY 2013 ERROR AMPLIFIER CONFIGURATION R4, C18, C17 These components configure the error amplifier gain characteristics to accomplish a stable overall loop gain. One advantage of current mode control is the ability to close the loop with only three feedback components, R4, C18 and C17. The overall loop gain is the product of the modulator gain and the error amplifier gain. The DC modulator gain of the LM5118 is as follows: RLOAD x VIN DCGain(MOD) = 10RS(VIN + 2VOUT) (26) The dominant, low frequency pole of the modulator is determined by the load resistance (RLOAD) and output capacitance (COUT). The corner frequency of this pole is: 1 + DMIN fP(MOD) = 2S x RLOAD x COUT (27) For this example, RLOAD = 4Ω, DMIN = 0.294, and COUT = 454 µF, therefore: fP(MOD) = 149 Hz DC Gain(MOD) =3.63 = 11.2 dB Additionally, there is a right-half plane (RHP) zero associated with the modulator. The frequency of the RHP zero is: fRHPzero = RLOAD (1 - D)2 2S x L x D (28) fRHPzero = 7.8 kHz The output capacitor ESR produces a zero given by: ESRzero = 1 2S x ESR x COUT (29) ESRZERO = 70 kHz The RHP zero complicates compensation. The best design approach is to reduce the loop gain to cross zero at about 30% of the calculated RHP zero frequency. The Type ll error amplifier compensation provided by R4, C18 and C17 places one pole at the origin for high DC gain. The 2nd pole should be located close to the RHP zero. The error amplifier zero (see below) should be placed near the dominate modulator pole. This is a good starting point for compensation. Refer to the on-line LM5118 Quick-Start calculator for ready to use equations and more details. Components R4 and C18 configure the error amplifier as a type II configuration which has a DC pole and a zero at: 1 fz = 2 x S x R4 x C18 (30) C17 introduces an additional pole used to cancel high frequency switching noise. The error amplifier zero cancels the modulator pole leaving a single pose response at the crossover frequency of the loop gain if the crossover frequency is much lower than the right half plane zero frequency. A single pole response at the crossover frequency yields a very stable loop with 90 degrees of phase margin. Copyright © 2008–2013, Texas Instruments Incorporated Product Folder Links: LM5118 LM5118-Q1 Submit Documentation Feedback 27 LM5118, LM5118-Q1 SNVS566G – APRIL 2008 – REVISED FEBRUARY 2013 www.ti.com For the design example, a target loop bandwidth (crossover frequency) of 2.0 kHz was selected (about 30% of the right-half-plane zero frequency). The error amplifier zero (fz) should be selected at a frequency near that of the modulator pole and much less than the target crossover frequency. This constrains the product of R4 and C18 for a desired compensation network zero to be less than 2 kHz. Increasing R4, while proportionally decreasing C18 increases the error amp gain. Conversely, decreasing R4 while proportionally increasing C18 decreases the error amp gain. For the design example C18 was selected for 4.7 nF and R4 was selected to be 10 kΩ. These values set the compensation network zero at 149 Hz. The overall loop gain can be predicted as the sum (in dB) of the modulator gain and the error amp gain. 100 180 40 -30 80 150 20 -60 60 120 0 -90 40 90 -20 -40 -60 .001 20 -120 .01 .1 1 10 100 60 0 -150 30 -20 .001 -180 1000 PHASE (°) 0 GAIN (dB) 60 PHASE (°) GAIN (dB) If a network analyzer is available, the modulator gain can be measured and the error amplifier gain can be configured for the desired loop transfer function. If a network analyzer is not available, the error amplifier compensation components can be designed with the guidelines given. Step load transient tests can be performed to verify acceptable performance. The step load goal is minimal overshoot with a damped response. .01 .1 1 10 100 0 1000 FREQUENCY (kHz) FREQUENCY (kHz) Figure 21. Modulator Gain and Phase Figure 22. Error Amplifier Gain and Phase 100 80 GAIN (dB) 60 40 20 0 -20 .001 .01 .1 1 10 100 1000 FREQUENCY (kHz) Figure 23. Overall Loop Gain and Phase The plots shown in Figure 21, Figure 22, and Figure 23 illustrate the gain and phase diagrams of the design example. The overall bandwidth is lower in a buck-boost application due the compensation challenges associated with the right-half-plane zero. For a pure buck application, the bandwidth could be much higher. The LM5116 datasheet is a good reference for compensation design of a pure buck mode regulator. Bias Power Dissipation Reduction Buck or Buck-boost regulators operating with high input voltage can dissipate an appreciable amount of power while supplying the required bias current of the IC. The VCC regulator must step-down the input voltage VIN to a nominal VCC level of 7V. The large voltage drop across the VCC regulator translates into high power dissipation in the VCC regulator. There are several techniques that can significantly reduce this bias regulator power dissipation. Figure 24 and Figure 25 depict two methods to bias the IC, one from the output voltage and one from 28 Submit Documentation Feedback Copyright © 2008–2013, Texas Instruments Incorporated Product Folder Links: LM5118 LM5118-Q1 LM5118, LM5118-Q1 www.ti.com SNVS566G – APRIL 2008 – REVISED FEBRUARY 2013 a separate bias supply. In the first case, the internal VCC regulator is used to initially bias the VCC pin. After the output voltage is established, the VCC pin bias current is supplied through the VCCX pin, which effectively disables the internal VCC regulator. Any voltage greater than 4.0V can supply VCC bias through the VCCX pin. However, the voltage applied to the VCCX pin should never exceed 15V. The voltage supplied through VCCX must be large enough to drive the switching MOSFETs into full saturation. HB VIN HO Q1 D2 VOUT L1 HS D1 LM5118 Cout CS CSG LO Q2 GND VCC VCCX Figure 24. VCC Bias from VOUT 4V < VOUT < 15V HB VIN Q1 D2 HO VOUT L1 HS LM5118 D1 CS Cout Q2 LO VOUT CSG VCC VCCX VBIAS Figure 25. VCC Bias with Additional Bias Supply PCB Layout and Thermal Considerations In a buck-boost regulator, there are two loops where currents are switched very fast. The first loop starts from the input capacitors, and then to the buck switch, the inductor, the boost switch then back to the input capacitor. The second loop starts from the inductor, and then to the output diode, the output capacitor, the recirculating diode, and back to the inductor. Minimizing the PC board area of these two loops reduces the stray inductance and minimizes noise and the possibility of erratic operation. A ground plane in the PC board is recommended as a means to connect the input filter capacitors to the output filter capacitors and the PGND pins of the LM5118. Connect all of the low current ground connections (CSS, RT, CRAMP) directly to the regulator AGND pin. Connect the AGND and PGND pins together through topside copper area covering the entire underside of the device. Place several vias in this underside copper area to the ground plane of the input capacitors. Copyright © 2008–2013, Texas Instruments Incorporated Product Folder Links: LM5118 LM5118-Q1 Submit Documentation Feedback 29 LM5118, LM5118-Q1 SNVS566G – APRIL 2008 – REVISED FEBRUARY 2013 www.ti.com The highest power dissipating components are the two power MOSFETs, the recirculating diode, and the output diode. The easiest way to determine the power dissipated in the MOSFETs is to measure the total conversion losses (PIN - POUT), then subtract the power losses in the Schottky diodes, output inductor and any snubber resistors. An approximation for the recirculating Schottky diode loss is: P = (1-D) x IOUT x VFWD. (31) The boost diode loss is P = IOUT x VFWD. (32) If a snubber is used, the power loss can be estimated with an oscilloscope by observation of the resistor voltage drop at both turn-on and turn-off transitions. The LM5118 package has an exposed thermal pad to aid power dissipation. Selecting diodes with exposed pads will aid the power dissipation of the diodes as well. When selecting the MOSFETs, pay careful attention to RDS(ON) at high temperature. Also, selecting MOSFETs with low gate charge will result in lower switching losses. Figure 26. 12V, 3A Typical Application Schematic 30 Submit Documentation Feedback Copyright © 2008–2013, Texas Instruments Incorporated Product Folder Links: LM5118 LM5118-Q1 LM5118, LM5118-Q1 www.ti.com SNVS566G – APRIL 2008 – REVISED FEBRUARY 2013 REVISION HISTORY Changes from Revision F (February 2013) to Revision G • Page Changed layout of National Data Sheet to TI format .......................................................................................................... 30 Copyright © 2008–2013, Texas Instruments Incorporated Product Folder Links: LM5118 LM5118-Q1 Submit Documentation Feedback 31 PACKAGE OPTION ADDENDUM www.ti.com 11-Apr-2013 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish (2) MSL Peak Temp Op Temp (°C) Top-Side Markings (3) (4) LM5118MH/NOPB ACTIVE HTSSOP PWP 20 73 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 LM5118 MH LM5118MHX/NOPB ACTIVE HTSSOP PWP 20 2500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 LM5118 MH LM5118Q1MH/NOPB ACTIVE HTSSOP PWP 20 73 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 LM5118 Q1MH LM5118Q1MHX/NOPB ACTIVE HTSSOP PWP 20 2500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 LM5118 Q1MH (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) Multiple Top-Side Markings will be inside parentheses. Only one Top-Side Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Top-Side Marking for that device. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com 11-Apr-2013 OTHER QUALIFIED VERSIONS OF LM5118, LM5118-Q1 : • Catalog: LM5118 • Automotive: LM5118-Q1 NOTE: Qualified Version Definitions: • Catalog - TI's standard catalog product • Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 8-Apr-2013 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) LM5118MHX/NOPB HTSSOP PWP 20 2500 330.0 16.4 LM5118Q1MHX/NOPB HTSSOP PWP 20 2500 330.0 16.4 Pack Materials-Page 1 B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant 6.95 7.1 1.6 8.0 16.0 Q1 6.95 7.1 1.6 8.0 16.0 Q1 PACKAGE MATERIALS INFORMATION www.ti.com 8-Apr-2013 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) LM5118MHX/NOPB HTSSOP PWP 20 2500 367.0 367.0 35.0 LM5118Q1MHX/NOPB HTSSOP PWP 20 2500 367.0 367.0 35.0 Pack Materials-Page 2 MECHANICAL DATA PWP0020A MXA20A (Rev C) www.ti.com IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2013, Texas Instruments Incorporated