SHARP PQ070XZ02ZZH

PQ070XZ02ZxH
PQ070XZ02ZxH
Low Voltage Operation
Low Power-loss Voltage Regulator
■ Outline Dimensions
Features
(Unit : mm)
1.Low voltage operation (Minimum operating voltage: 2.35V)
2.Low dissipation current
Dissipation current at no load: MAX.2mA
Output OFF-state dissipation current: MAX.5μA
3.Low power-loss (Dropout voltage: MAX.0.5V)
4.Built-in overcurrent and overheat protection functions
5.RoHS directive compliant
2.3±0.5
6.6MAX.
5.2±0.5
(0.5)
3
(1.7)
H
(0~0.25)
0.5+0.2
-0.1
Applications
(0.5)
4–(1.27)
1.Peripheral equipment of personal computers
2.Power supplies for various electronic equipment such as
DVD player or STB
(
(0.9)
5.5±0.5
Lead finish
identification mark
2.5MIN.
9.7MAX.
Epoxy resin
070XZ02
) : Typical dimensions
Product mass:(0.3g)
1
Model Line-up
2
3
4
5
1
3
Specific IC
Output
current (IO)
2A
Package
type
Taping
Sleeve
2
Variable
output
4
5
1
2
PQ070XZ02ZPH
3
4
PQ070XZ02ZZH
5
DC input (VIN)
ON/OFF control (VC)
DC output (VO)
Output adjustment (Vadj)
GND
Lead finish:Lead-free solder plating
(Composition: Sn2Cu)
Absolute Maximum Ratings
(Ta=25°C)
Parameter
Symbol
VIN
Input voltage
*1 Output control voltage
VC
*1 Output adjustment pin voltage
Vadj
Output current
IO
*2
Pd
Power dissipation
*3
Tj
Junction temperature
Operating temperature
Topr
Storage temperature
Tstg
Soldering temperature
Tsol
*1
Rating
10
10
5
2
8
150
-40 to +85
-40 to +150
260(10s)
Unit
V
V
V
A
W
°C
°C
°C
°C
*1 All are open except GND and applicable terminals.
*2 Pd:With infinite heat sink
*3 There is case that over heat protection operates at the temperature Tj:125°C to 150°C,
so this item cannot be used in this temperature range.
Notice The content of data sheet is subject to change without prior notice.
In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in equipment using any SHARP
devices shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.
1
Sheet No.: OP07009
PQ070XZ02ZxH
Electrical Characteristics
(Unless otherwise specified, condition shall be VIN=5V, VO=3V(R1=1kΩ), IO=0.5A, VC=2.7V,Ta=25˚C)
Symbol
Conditions
MIN.
TYP.
MAX.
Unit
Input voltage
VIN
2.35
V
VO
Load regulation
RegL
IO=5mA to 2.0A
Line regulation
RegI
VIN=4 to 8V,IO=5mA
-
-
10
Output voltage
-
Ripple rejection
RR
Refer to Fig.2
45
Dropout voltage
VI-O
VIN=2.85V,IO=2.0A
Reference voltage
Vref
-
Temperature coefficient of reference voltage
TCVref
Tj=0 to 125°C, IO=5mA
ON-state voltage for control
VC(ON)
ON-state current for control
IC(ON)
-
OFF-state voltage for control
VC(OFF)
IO=0A
OFF-state current for control
IC(OFF)
IO=0A, VC=0.4V
Iq
Iqs
VC=0.4V
Parameter
4
Quiescent current
Output OFF-state consumption current
4
1.5
7
V
0.2
2
%
0.2
1
%
60
-
-
dB
0.5
V
1.225
1.25
1.275
V
-
±1.0
-
%
200
μA
-
4
2.0
-
IO=0A
1
-
V
0.8
V
2
2
μA
mA
5
μA
In case of opening control terminal ② , output voltage turns off.
Fig.1 Test Circuit
VIN
VO
3
1
R2
VC
2
+
4
IO
+
5
A
0.33μF
A
Vref
V
47μF
IC
A
R1
1kΩ
Iq
V
RL
VO=Vref×(1+R2/R1)
[R1=1kΩ,Vref≒1.25V]
Fig.2 Test Circuit for Ripple Rejection
+
3
1
ei ~
R2
+
VIN
VC
4
2
Vref
5
0.33μF
IO
eo
+
47μF
V
~
RL
R1
1kΩ
2.7V
f=120Hz sine wave
ei(rms)=0.5V
VO=3V(R1=1kΩ)
VIN=5V
IO=0.3A
RR=20log(ei(rms)/eo(rms))
Sheet No.: OP07009
2
PQ070XZ02ZxH
Fig.4 Overcurrent Protection
Characteristics
Fig.3 Power Dissipation vs. Ambient
Temperature
3.0
Power dissipation PD (W)
10
PD : With infinite heat sink
2.5
Output voltage VO (V)
8
VO=3.0V 5
VIN=10.0V
VIN=4.5V
2.0
VIN=5.5V
1.5
VIN=5.0V
1.0
VIN=7.0V
0.5
0
-40 -20
0
0
20 40 60 80 100 120 140 150
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
Output current IO (A)
Ambient temperature Ta (°C)
Note) Oblique line portion:Overheat protection may operate in this area.
Power dissipation PD (W)
Fig.5 Power Dissipation vs. Ambient
Temperature (Typical Value)
2.0
1.5
1.0
Cu area 740mm2
Cu area 180mm2
Cu area 100mm2
Cu area 70mm2
PWB PWB Cu
Cu area 36mm2
0.5
0
-40
Material
:Glass-cloth epoxy resin
Size
:50×50×1.6mm
Cu thickness:35μm
-20
0
20
40
60
80
Ambient temperature Ta (°C)
Fig.6 Output Voltage Adjustment
Characteristics (Typical Value)
10
R1=1kΩ
Output voltage VO (V)
9
8
7
6
5
4
3
2
1
0
100
103
104
R2 (Ω)
Sheet No.: OP07009
3
PQ070XZ02ZxH
Fig.7 Typical Application
DC input
1
VO
3
R2
VIN
+
2
CO +
4
CIN
Load
5
R1
1kΩ
ON/OFF signal
High:Output ON
Low or Open:Output OFF
■ Setting of Output Voltage
Output
voltage is able to set from 1.5V to 7V when resistors R1 and R2 are attached to ③,④,⑤ terminals. As for the external
resistors to set output voltage, refer to the figure below and Fig.6.
VO
3
R2
-
4
R1
+
5
Vref
VO=Vref × (1+R2/R1)
[R1=1kΩ, Vref≒1.25V]
Sheet No.: OP07009
4