FR601G-FR607G 50V-1000V 6.0A GLASS PASSIVATED FAST RECOVERY RECTIFIERS FEATURES • • • • • Fast switching for high efficiency Glass passivated chip junction High current surge capability Low leakage High temperature soldering guaranteed 260 /10 seconds,0.375 (9.5mm)lead length at 5 lbs (2.3kg) tension MECHANICAL DATA • • • • • • Case: Transfer molded plastic Epoxy: UL94V-0 rate flame retardant Polarity: Color band denotes cathode end Lead: Plated axial lead, solderable per MIL-STD-202E method 208C Mounting position: Any Weight: 0.07 ounce, 2.0 gram Maximum Ratings and Electrical Characteristics Rating at 25 oC ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20% Type Number Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current .375”(9.5mm) Lead Length @T A = 55 oC Peak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method ) Maximum Instantaneous Forward Voltage @ 6.0A Maximum DC Reverse Current @T A =25 oC at Rated DC Blocking Voltage @ T A =125 oC Maximum Reverse Recovery Time ( Note 1) Typical Junction Capacitance ( Note 2 ) Typical Thermal Resistance Operating Temperature Range Symbol V RRM V RMS V DC FR FR FR FR FR FR FR Units 601G 602G 603G 604G 605G 606G 607G 50 100 200 400 600 800 1000 V 35 70 140 280 420 560 700 V 50 100 200 400 600 800 1000 V I(AV) 6.0 A IFSM 250 A VF 1.3 V IR 5.0 200 uA uA nS pF o C/W o C o C Trr Cj 150 R θJA TJ 250 50 30 -65 to +150 -65 to +150 Storage Temperature Range T STG 1. Reverse Recovery Test Conditions: IF =0.5A, IR =1.0A, IRR =0.25A Notes: 2. Measured at 1 MHz and Applied Reverse Voltage of 4.0 Volts D.C. 3. Mount on Cu-Pad Size 16mm x 16mm on P.C.B. E-mail: [email protected] 1 of 2 500 Web Site: www.taychipst.com FR601G-FR607G 50V-1000V 6.0A GLASS PASSIVATED FAST RECOVREY RECTIFIERS FIG.1-TYPICAL FORWARD CURRENT FIG.2-MAXIMUM NON-REPETITIVE PEAK DERATING CURVE FORWARD SURGE CURRENT PEAK FORWARD SURGE 6.0 Half Wave 60Hz Resistive or Inductive Load 0.375″(9.5mm) Lead Length 4.0 2.0 300 CURRENT, (A) Single Phase (A) AVERAGE FORWARD CURRENT, RATING AND CHRACTERISTIC CURVES FR601G THRU FR607G 8.3ms Single Half Sine-Wave (JEDEC Method) T= T jmax 200 100 1 Cycle 0 0 25 50 55 150 125 100 75 175 0 1 2 AMBIENT TEMPERATURE, ( C) 4 FIG.3-TYPICAL INSTANTANEOUS 0.1 TJ =25 C Pulse Width=300us 1% Duty Cycle 0.8 1.0 1.2 1.6 1.4 10 40 20 60 80 100 1.8 20 TJ =125 C 10 TJ =100 C (μA) INSTANTANEOUS REVERSE CURRENT, 1.0 (A) INSTANTANEOUS FORWARD CURRENT, 10 0.6 8 FIG.4-TYPICAL REVERSE CHARACTERISTICS FORWARD CHARACTERISTICS 0.01 0.4 6 NUMBER OF CYCLES AT 60 Hz 1.0 TJ =75 C 0.1 TJ=25 C INSTANTANEOUS FORWARD VOLTAGE,(V) 0.01 0 20 60 40 80 100 120 140 PERCENT OF RATED PEAK REVERSE VOLTAGE,(%) FIG.5-TYPICAL JUNCTION CAPACITANCE F1G.6-TEST CIRCUIT DIAGRAM AND REVERSE RECOVERY TIME CHARACTERISTIC JUNCTION CAPACITANCE,(pF) 210 180 Trr 50Ω 10Ω NONINDUCTIVE NONINDUCTIVE +0.5A 150 (-) 120 (+) 90 25 Vdc (approx.) (-) D.U.T. 1Ω NON INDUCTIVE PULSE GENERATIOR (NOTE 2) 0 -0.25A (+) OSCILLOSCOPE (NOTE 1) -1.0A 60 1cm T J =25 C f=1MHz Vsig=50mVp-p 30 0 0.1 1.0 10 100 200 NOTES : 1.Rise Time=7ns mas. Input Impedance= 1 magohm. 22pF 2.Rise time=10ns max. Source Impedance= 50 ohms SET TIME BASE FOR 50/100ns/cm REVERSE VOLTAGE,(V) E-mail: [email protected] 2 of 2 Web Site: www.taychipst.com