WINBOND W25X40BLSNIG

W25X10BL/20BL/40BL
1M-BIT, 2M-BIT AND 4M-BIT
2.5V SERIAL FLASH MEMORY WITH
4KB SECTORS AND DUAL I/O SPI
- 1-
Publication Release Date: October 14, 2009
Preliminary -- Revision A
W25X10BL/20BL/40BL
Table of Contents
1.
GENERAL DESCRIPTION.......................................................................................................... 4
2.
FEATURES ................................................................................................................................. 4
3.
PIN CONFIGURATION SOIC 150-MIL / 208-MIL ....................................................................... 5
4.
PAD CONFIGURATION WSON 6X5-MM................................................................................... 5
5.
PIN CONFIGURATION PDIP 300-MIL ....................................................................................... 6
6.
PIN DESCRIPTION SOIC 150 / 208-MIL, PDIP 300-MIL, WSON 6X5-MM ............................... 6
6.1
Package Types ............................................................................................................... 7
6.2
Chip Select (/CS) ............................................................................................................ 7
6.3
Serial Data Input, Output and IOs (DI, DO, IO0 and IO1) ............................................... 7
6.4
Write Protect (/WP)......................................................................................................... 7
6.5
HOLD (/HOLD)................................................................................................................ 7
6.6
Serial Clock (CLK) .......................................................................................................... 7
7.
BLOCK DIAGRAM ...................................................................................................................... 8
8.
FUNCTIONAL DESCRIPTION.................................................................................................... 9
8.1
8.2
SPI OPERATIONS.......................................................................................................... 9
8.1.1
Standard SPI Instructions ................................................................................................ 9
8.1.2
Dual SPI Instructions ........................................................................................................ 9
8.1.3
Hold Function ................................................................................................................... 9
WRITE PROTECTION ................................................................................................. 10
8.2.1
9.
Write Protect Features ................................................................................................... 10
CONTROL AND STATUS REGISTERS ................................................................................... 11
9.1
9.2
STATUS REGISTER .................................................................................................... 11
9.1.1
BUSY.............................................................................................................................. 11
9.1.2
Write Enable Latch (WEL) ............................................................................................. 11
9.1.3
Block Protect Bits (BP2, BP1, BP0) ............................................................................... 11
9.1.4
Top/Bottom Block Protect (TB)....................................................................................... 11
9.1.5
Reserved Bits ................................................................................................................. 11
9.1.6
Status Register Protect (SRP)........................................................................................ 12
9.1.7
Status Register Memory Protection ................................................................................ 13
INSTRUCTIONS ........................................................................................................... 14
9.2.1
Manufacturer and Device Identification .......................................................................... 14
9.2.2
Instruction Set ................................................................................................................ 15
9.2.3
Write Enable (06h) ......................................................................................................... 16
9.2.4
Write Disable (04h) ........................................................................................................ 16
9.2.5
Read Status Register (05h) ............................................................................................ 18
9.2.6
Write Status Register (01h) ............................................................................................ 19
9.2.7
Read Data (03h) ............................................................................................................. 21
9.2.8
Fast Read (0Bh) ............................................................................................................. 22
-2-
W25X10BL/20BL/40BL
10.
11.
12.
Fast Read Dual Output (3Bh) ......................................................................................... 23
Fast Read Dual I/O (BBh) ............................................................................................ 24
9.2.11
Continuous Read Mode Bits (M7-0) ............................................................................. 26
9.2.12
Continuous Read Mode Reset (FFFFh) ....................................................................... 26
9.2.13
Page Program (02h) ..................................................................................................... 27
9.2.14
Sector Erase (20h) ....................................................................................................... 28
9.2.15
32KB Block Erase (52h) ............................................................................................... 29
9.2.16
Block Erase (D8h) ........................................................................................................ 30
9.2.17
Chip Erase (C7h or 60h) .............................................................................................. 31
9.2.18
Power-down (B9h) ........................................................................................................ 32
9.2.19
Release Power-down / Device ID (ABh)....................................................................... 33
9.2.20
Read Manufacturer / Device ID (90h) ........................................................................... 35
9.2.21
Read Manufacturer / Device ID Dual I/O (92h)............................................................. 36
9.2.22
Read Unique ID Number (4Bh) .................................................................................... 37
9.2.23
JEDEC ID (9Fh) ........................................................................................................... 38
ELECTRICAL CHARACTERISTICS ......................................................................................... 39
10.1
Absolute Maximum Ratings .......................................................................................... 39
10.2
Operating Ranges ......................................................................................................... 39
10.3
Power-up Timing and Write Inhibit Threshold............................................................... 40
10.4
DC Electrical Characteristics ........................................................................................ 41
10.5
AC Measurement Conditions ........................................................................................ 42
10.6
AC Electrical Characteristics......................................................................................... 43
10.7
AC Electrical Characteristics (cont’d)............................................................................ 44
10.8
Serial Output Timing ..................................................................................................... 45
10.9
Input Timing .................................................................................................................. 45
10.10
Hold Timing ................................................................................................................. 45
PACKAGE SPECIFICATION .................................................................................................... 46
11.1
8-Pin SOIC 150-mil (Package Code SN) ...................................................................... 46
11.2
8-Pin SOIC 208-mil (Package Code SS) ...................................................................... 47
11.3
8-Pin PDIP 300-mil (Package Code DA) ...................................................................... 48
11.4
8-Contact 6x5mm WSON (Package Code ZP) ............................................................ 49
ORDERING INFORMATION..................................................................................................... 51
12.1
13.
9.2.9
9.2.10
Valid Part Numbers and Top Side Marking .................................................................. 52
REVISION HISTORY ................................................................................................................ 53
-3-
Publication Release Date: October 14, 2009
Preliminary -- Revision A
W25X10BL/20BL/40BL
1. GENERAL DESCRIPTION
The W25X10BL (1M-bit), W25X20BL (2M-bit) and the W25X40BL (4M-bit) Serial Flash memories
provides a storage solution for systems with limited space, pins and power. The 25X series offers
flexibility and performance well beyond ordinary Serial Flash devices. They are ideal for code download
applications as well as storing voice, text and data. The devices operate on a single 2.3V to 3.6V
power supply with current consumption as low as 4mA active and 1µA for power-down. All devices are
offered in space-saving packages.
The W25X10BL/20BL/40BL arrays are organized into 512/1,024/2,048 programmable pages of 256bytes each. Up to 256 bytes can be programmed at a time using the Page Program instruction. Pages
can be erased in groups of 16 (sector erase), groups of 128 (32KB block erase), groups of 256 (block
erase) or the entire chip (chip erase). The W25X10BL/20BL/40BL has 32/64/128 erasable sectors and
2/4/8 erasable 64KB blocks respectively. The small 4KB sectors allow for greater flexibility in
applications that require data and parameter storage. (See figure 2.)
The W25X10BL/20BL/40BL supports the standard Serial Peripheral Interface (SPI), and a high
performance dual output as well as Dual I/O SPI: Serial Clock, Chip Select, Serial Data DI (I/O0), DO
(I/O1). SPI clock frequencies of up to 50MHz are supported allowing equivalent clock rates of 100MHz
when using the Fast Read Dual Output instruction. These transfer rates are comparable to those of 8
and 16-bit Parallel Flash memories.
A Hold pin, Write Protect pin and programmable write protect, with top or bottom array control features,
provide further control flexibility. Additionally, the device supports JEDEC standard manufacturer and
device identification.
2. FEATURES
• Software and Hardware Write Protection
– Write-Protect all or portion of memory
– Enable/Disable protection with /WP pin
– Top or bottom array protection
– Volatile & Non-volatile Status Register Bits
• Family of Serial Flash Memories
– W25X10BL: 1M-bit/128K-byte (131,072)
– W25X20BL: 2M-bit/256K-byte (262,144)
– W25X40BL: 4M-bit/512K-byte (524,288)
– 256-bytes per programmable page
– Uniform 4KB Sectors, 32KB & 64KB Blocks
• Flexible Architecture with 4KB sectors
– Sector Erase (4K-bytes)
– Block Erase (32K and 64K-byte)
– Page program up to 256 bytes <1ms
– More than 100,000 erase/write cycles
– More than 20-year retention
• SPI with Single / Dual Outputs / Dual I/O
– Clock, Chip Select, Data I/O, Data Out
– Optional Hold function for SPI flexibility
• Data Transfer up to 100M-bits / second
– Clock operation to 50MHz
– Fast Read Dual Output instruction
– Auto-increment Read capability
• Low Power Consumption, Wide
Temperature Range
– Single 2.3 to 3.6V supply
– 4mA active current, 1µA Power-down (typ)
– -40° to +85°C operating range
• Efficient “Continuous Read Mode”
– Low Instruction overhead
– Continuous Read
– As few as 8 clocks to address memory
– Allows true XIP (execute in place) operation
• Space Efficient Packaging
– 8-pin SOIC 150-mil
– 8-pin SOIC 208-mil
– 8-pad WSON 6x5-mm
– 8-pin PDIP 300-mil
-4-
W25X10BL/20BL/40BL
3. PIN CONFIGURATION SOIC 150-MIL / 208-MIL
Figure 1a. W25X10BL/20BL/40BL Pin Assignments, 8-pin SOIC 150 / 208-mil (Package Code SN & SS)
4. PAD CONFIGURATION WSON 6X5-MM
Figure 1b. W25X10BL/20BL/40BL Pad Assignments, 8-pad WSON 6X5-mm (Package Code ZP)
-5-
Publication Release Date: October 14, 2009
Preliminary -- Revision A
W25X10BL/20BL/40BL
5. PIN CONFIGURATION PDIP 300-MIL
Figure 1c. W25X40BL Pin Assignments, 8-pin PDIP (Package Code DA)
6. PIN DESCRIPTION SOIC 150 / 208-MIL, PDIP 300-MIL, WSON 6X5-MM
PIN NO.
PIN NAME
I/O
FUNCTION
1
/CS
I
Chip Select Input
2
DO (IO1)
O
Data Input / Output
3
/WP
I
Write Protect Input
4
GND
5
DIO (IO0)
I/O
Data Input / Output
6
CLK
I
Serial Clock Input
7
/HOLD
I
Hold Input
8
VCC
Ground
Power Supply
-6-
W25X10BL/20BL/40BL
6.1
Package Types
W25X10BL/20BL/40BL are offered in an 8-pin plastic 150-mil width SOIC (package code SN) and 6x5mm WSON (package code ZP), see figures 1a and 1b, respectively. The W25X40BL is offered in the
208-mil width SOIC (package code SS) and the 300-mil 8-pin PDIP (package code DA), see figure 1c.
Package diagrams and dimensions are illustrated at the end of this datasheet.
6.2
Chip Select (/CS)
The SPI Chip Select (/CS) pin enables and disables device operation. When /CS is high the device is
deselected and the Serial Data Output (DO) pin is at high impedance. When deselected, the devices
power consumption will be at standby levels unless an internal erase, program or status register cycle
is in progress. When /CS is brought low the device will be selected, power consumption will increase to
active levels and instructions can be written to and data read from the device. After power-up, /CS
must transition from high to low before a new instruction will be accepted. The /CS input must track the
VCC supply level at power-up (see “Write Protection” and Figure 26). If needed a pull-up resister on
/CS can be used to accomplish this.
6.3
Serial Data Input, Output and IOs (DI, DO, IO0 and IO1)
The W25X10BL/20BL/40BL supports standard SPI and Dual SPI operation. Standard SPI instructions
use the unidirectional DI (input) pin to serially write instructions, addresses or data to the device on the
rising edge of the Serial Clock (CLK) input pin. Standard SPI also uses the unidirectional DO (output)
to read data or status from the device on the falling edge of CLK.
Dual SPI instructions use the bidirectional IO pins to serially write instructions, addresses or data to the
device on the rising edge of CLK and read data or status from the device on the falling edge of CLK.
6.4
Write Protect (/WP)
The Write Protect (/WP) pin can be used to prevent the Status Register from being written. Used in
conjunction with the Status Register’s Block Protect (BP2, BP1, and BP0) bits and Status Register
Protect (SRP) bit, a portion or the entire memory array can be hardware protected. The /WP pin is
active low.
6.5
HOLD (/HOLD)
The Hold (/HOLD) pin allows the device to be paused while it is actively selected. When /HOLD is
brought low, while /CS is low, the DO pin will be at high impedance and signals on the DIO and CLK
pins will be ignored (don’t care). When /HOLD is brought high, device operation can resume. The
/HOLD function can be useful when multiple devices are sharing the same SPI signals. (“See Hold
function”)
6.6
Serial Clock (CLK)
The SPI Serial Clock Input (CLK) pin provides the timing for serial input and output operations. (“See
SPI Operations”)
-7-
Publication Release Date: October 14, 2009
Preliminary -- Revision A
W25X10BL/20BL/40BL
7. BLOCK DIAGRAM
Block Segmentation
xxFF00h
•
xxF000h
Sector 15 (4KB)
xxFFFFh
•
xxF0FFh
xxEF00h
•
xxE000h
Sector 14 (4KB)
xxEFFFh
•
xxE0FFh
xxDF00h
•
xxD000h
Sector 13 (4KB)
xxDFFFh
•
xxD0FFh
07FF00h
•
070000h
Block 7 (64KB)
xx2FFFh
•
xx20FFh
xx1F00h
•
xx1000h
Sector 1 (4KB)
xx1FFFh
•
xx10FFh
xx0F00h
•
xx0000h
Sector 0 (4KB)
xx0FFFh
•
xx00FFh
Write Control
Logic
04FF00h
•
040000h
Block 4 (64KB)
04FFFFh
•
0400FFh
03FF00h
•
030000h
Block 3 (64KB)
03FFFFh
•
0300FFh
W25X20BL
Sector 2 (4KB)
Write Protect Logic and Row Decode
xx2F00h
•
xx2000h
W25X40BL
•
•
•
•
•
•
/WP
07FFFFh
•
0700FFh
•
•
•
High Voltage
Generators
/HOLD
CLK
/CS
SPI
Command &
Control Logic
Page Address
Latch / Counter
01FF00h
•
010000h
Block 1 (64KB)
01FFFFh
•
0100FFh
00FF00h
•
000000h
Block 0 (64KB)
00FFFFh
•
0000FFh
Beginning
Page Address
Column Decode
And 256-Byte Page Buffer
Data
DIO (IO0)
DO (IO1)
Ending
Page Address
Byte Address
Latch / Counter
Figure 2. W25X10BL/20BL/40BL Block Diagram
-8-
W25X10BL
Status
Register
W25X10BL/20BL/40BL
8.
FUNCTIONAL DESCRIPTION
8.1
SPI OPERATIONS
8.1.1
Standard SPI Instructions
The W25X10BL/20BL/40BL are accessed through an SPI compatible bus consisting of four signals:
Serial Clock (CLK), Chip Select (/CS), Serial Data Input (DI) and Serial Data Output (DO). Standard
SPI instructions use the DI input pin to serially write instructions, addresses or data to the device on the
rising edge of CLK. The DO output pin is used to read data or status from the device on the falling
edge CLK.
SPI bus operation Modes 0 (0,0) and 3 (1,1) are supported. The primary difference between Mode 0
and Mode 3 concerns the normal state of the CLK signal when the SPI bus master is in standby and
data is not being transferred to the Serial Flash. For Mode 0 the CLK signal is normally low on the
falling and rising edges of /CS. For Mode 3 the CLK signal is normally high on the falling and rising
edges of /CS..
8.1.2
Dual SPI Instructions
The W25X10BL/20BL/40BL supports Dual SPI operation when using the “Fast Read Dual Output
(3Bh)” and “Fast Read Dual I/O (BBh)” instructions. These instructions allow data to be transferred to
or from the device at two to three times the rate of ordinary Serial Flash devices. The Dual SPI Read
instructions are ideal for quickly downloading code to RAM upon power-up (code-shadowing) or for
executing non-speed-critical code directly from the SPI bus (XIP). When using Dual SPI instructions,
the DI and DO pins become bidirectional I/O pins: IO0 and IO1.
8.1.3
Hold Function
The /HOLD signal allows the W25X10BL/20BL/40BL operation to be paused while it is actively
selected (when /CS is low). The /HOLD function may be useful in cases where the SPI data and clock
signals are shared with other devices. For example, consider if the page buffer was only partially
written when a priority interrupt requires use of the SPI bus. In this case the /HOLD function can save
the state of the instruction and the data in the buffer so programming can resume where it left off once
the bus is available again.
To initiate a /HOLD condition, the device must be selected with /CS low. A /HOLD condition will activate
on the falling edge of the /HOLD signal if the CLK signal is already low. If the CLK is not already low
the /HOLD condition will activate after the next falling edge of CLK. The /HOLD condition will terminate
on the rising edge of the /HOLD signal if the CLK signal is already low. If the CLK is not already low the
/HOLD condition will terminate after the next falling edge of CLK.
During a /HOLD condition, the Serial Data Output (DO) is high impedance, and Serial Data
Input/Output (DIO) and Serial Clock (CLK) are ignored. The Chip Select (/CS) signal should be kept
active (low) for the full duration of the /HOLD operation to avoid resetting the internal logic state of the
device.
-9-
Publication Release Date: October 14, 2009
Preliminary -- Revision A
W25X10BL/20BL/40BL
8.2
WRITE PROTECTION
Applications that use non-volatile memory must take into consideration the possibility of noise and
other adverse system conditions that may compromise data integrity. To address this concern the
W25X10BL/20BL/40BL provides several means to protect data from inadvertent writes.
8.2.1
Write Protect Features
•
Device resets when VCC is below threshold.
•
Time delay write disable after Power-up.
•
Write enable/disable instructions.
•
Automatic write disable after program and erase.
•
Software write protection using Status Register.
•
Hardware write protection using Status Register and /WP pin.
•
Write Protection using Power-down instruction.
Upon power-up or at power-down the W25X10BL/20BL/40BL will maintain a reset condition while VCC
is below the threshold value of VWI, (See Power-up Timing and Voltage Levels and Figure 26). While
reset, all operations are disabled and no instructions are recognized. During power-up and after the
VCC voltage exceeds VWI, all program and erase related instructions are further disabled for a time
delay of tPUW . This includes the Write Enable, Page Program, Sector Erase, Block Erase, Chip Erase
and the Write Status Register instructions. Note that the chip select pin (/CS) must track the VCC
supply level at power-up until the VCC-min level and tVSL time delay is reached. If needed a pull-up
resister on /CS can be used to accomplish this.
After power-up the device is automatically placed in a write-disabled state with the Status Register
Write Enable Latch (WEL) set to a 0. A Write Enable instruction must be issued before a Page
Program, Sector Erase, Chip Erase or Write Status Register instruction will be accepted. After
completing a program, erase or write instruction the Write Enable Latch (WEL) is automatically cleared
to a write-disabled state of 0.
Software controlled write protection is facilitated using the Write Status Register instruction and setting
the Status Register Protect (SRP) and Block Protect (TB, BP2, BP1, and BP0) bits. These Status
Register bits allow a portion or all of the memory to be configured as read only. Used in conjunction
with the Write Protect (/WP) pin, changes to the Status Register can be enabled or disabled under
hardware control. See Status Register for further information.
Additionally, the Power-down instruction offers an extra level of write protection as all instructions are
ignored except for the Release Power-down instruction.
- 10 -
W25X10BL/20BL/40BL
9.
CONTROL AND STATUS REGISTERS
The Read Status Register instruction can be used to provide status on the availability of the Flash
memory array, if the device is write enabled or disabled, and the state of write protection. The Write
Status Register instruction can be used to configure the device write protection features. See Figure 3.
9.1
9.1.1
STATUS REGISTER
BUSY
BUSY is a read only bit in the status register (S0) that is set to a 1 state when the device is executing a
Page Program, Sector Erase, Block Erase, Chip Erase or Write Status Register instruction. During this
time the device will ignore further instructions except for the Read Status Register instruction (see tW ,
tPP, tSE, tBE, and tCE in AC Characteristics). When the program, erase or write status register
instruction has completed, the BUSY bit will be cleared to a 0 state indicating the device is ready for
further instructions.
9.1.2
Write Enable Latch (WEL)
Write Enable Latch (WEL) is a read only bit in the status register (S1) that is set to a 1 after executing
a Write Enable Instruction. The WEL status bit is cleared to a 0 when the device is write disabled. A
write disable state occurs upon power-up or after any of the following instructions: Write Disable, Page
Program, Sector Erase, Block Erase, Chip Erase and Write Status Register.
9.1.3
Block Protect Bits (BP2, BP1, BP0)
The Block Protect Bits (BP2, BP1, and BP0) are non-volatile read/write bits in the status register (S4,
S3, and S2) that provide Write Protection control and status. Block Protect bits can be set using the
Write Status Register Instruction (see tW in AC characteristics). All, none or a portion of the memory
array can be protected from Program and Erase instructions (see Status Register Memory Protection
table). The factory default setting for the Block Protection Bits is 0, none of the array protected. The
Block Protect bits cannot be written to if the Status Register Protect (SRP) bit is set to 1 and the Write
Protect (/WP) pin is low.
9.1.4
Top/Bottom Block Protect (TB)
The Top/Bottom bit (TB) controls if the Block Protect Bits (BP2, BP1, BP0) protect from the Top (TB=0)
or the Bottom (TB=1) of the array as shown in the Status Register Memory Protection table. The TB bit
is non-volatile and the factory default setting is TB=0. The TB bit can be set with the Write Status
Register Instruction provided that the Write Enable instruction has been issued. The TB bit cannot be
written to if the Status Register Protect (SRP) bit is set to 1 and the Write Protect (/WP) pin is low.
9.1.5
Reserved Bits
Status register bit location S6 is reserved for future use. Current devices will read 0 for this bit location.
It is recommended to mask out the reserved bit when testing the Status Register. Doing this will ensure
compatibility with future devices.
- 11 -
Publication Release Date: October 14, 2009
Preliminary -- Revision A
W25X10BL/20BL/40BL
9.1.6
Status Register Protect (SRP)
The Status Register Protect (SRP) bit is a non-volatile read/write bit in status register (S7) that can be
used in conjunction with the Write Protect (/WP) pin to disable writes to status register. When the SRP
bit is set to a 0 state (factory default) the /WP pin has no control over status register. When the SRP
pin is set to a 1, the Write Status Register instruction is locked out while the /WP pin is low. When the
/WP pin is high the Write Status Register instruction is allowed.
Figure 3. Status Register Bit Locations
- 12 -
W25X10BL/20BL/40BL
9.1.7
Status Register Memory Protection
STATUS REGISTER(1)
W25X40BL (4M-BIT) MEMORY PROTECTION
TB
BP2
BP1
BP0
BLOCK(S)
ADDRESSES
DENSITY
PORTION
x
0
0
0
1
1
1
x
0
0
0
0
0
0
0
1
0
0
1
1
0
1
1
x
0
1
0
1
1
0
1
x
NONE
7
6 and 7
4 thru 7
0
0 and 1
0 thru 3
0 thru 7
NONE
070000h - 07FFFFh
060000h - 07FFFFh
040000h - 07FFFFh
000000h - 00FFFFh
000000h - 01FFFFh
000000h - 03FFFFh
000000h - 07FFFFh
NONE
64KB
128KB
256KB
64KB
128KB
256KB
512KB
NONE
Upper 1/8
Upper 1/4
Upper 1/2
Lower 1/8
Lower 1/4
Lower 1/2
ALL
STATUS REGISTER(1)
W25X20BL (2M-BIT) MEMORY PROTECTION
TB
BP2
BP1
BP0
BLOCK(S)
ADDRESSES
DENSITY
PORTION
x
0
0
1
1
x
x
x
x
x
x
x
0
0
1
0
1
1
0
1
0
1
0
1
NONE
3
2 and 3
0
0 and 1
0 thru 3
NONE
030000h - 03FFFFh
020000h - 03FFFFh
000000h - 00FFFFh
000000h - 01FFFFh
000000h - 03FFFFh
NONE
64KB
128KB
64KB
128KB
256KB
NONE
Upper 1/4
Upper 1/2
Lower 1/4
Lower 1/2
ALL
STATUS REGISTER(1)
W25X10BL (1M-BIT) MEMORY PROTECTION
TB
BP2
BP1
BP0
BLOCK(S)
ADDRESSES
DENSITY
PORTION
x
0
1
x
x
x
x
x
0
0
0
1
0
1
1
x
NONE
1
0
0 and 1
NONE
010000h - 01FFFFh
000000h - 00FFFFh
000000h - 01FFFFh
NONE
64KB
64KB
128KB
NONE
Upper 1/2
Lower 1/2
ALL
Note:
1. x = don’t care
- 13 -
Publication Release Date: October 14, 2009
Preliminary -- Revision A
W25X10BL/20BL/40BL
9.2
INSTRUCTIONS
The instruction set of the W25X10BL/20BL/40BL consists of nineteen basic instructions that are fully
controlled through the SPI bus (see Instruction Set table). Instructions are initiated with the falling edge
of Chip Select (/CS). The first byte of data clocked into the DIO input provides the instruction code.
Data on the DIO input is sampled on the rising edge of clock with most significant bit (MSB) first.
Instructions vary in length from a single byte to several bytes and may be followed by address bytes,
data bytes, dummy bytes (don’t care), and in some cases, a combination. Instructions are completed
with the rising edge of edge /CS. Clock relative timing diagrams for each instruction are included in
figures 4 through 25. All read instructions can be completed after any clocked bit. However, all
instructions that Write, Program or Erase must complete on a byte boundary (CS driven high after a full
8-bits have been clocked) otherwise the instruction will be terminated. This feature further protects the
device from inadvertent writes. Additionally, while the memory is being programmed or erased, or when
the Status Register is being written, all instructions except for Read Status Register will be ignored until
the program or erase cycle has completed.
9.2.1
Manufacturer and Device Identification
MANUFACTURER ID
(M7-M0)
Winbond Serial Flash
EFh
Device ID
(ID7-ID0)
(ID15-ID0)
Instruction
ABh, 90h, 92h
9Fh
W25X10BL
10h
3011h
W25X20BL
11h
3012h
W25X40BL
12h
3013h
- 14 -
W25X10BL/20BL/40BL
9.2.2
Instruction Set (1)
INSTRUCTION NAME
BYTE 1
CODE
BYTE 2
BYTE 3
BYTE 4
BYTE
5
BYTE 6 N-BYTES
Write Enable
06h
Write Disable
04h
Write Enable for Volatile
Status Register
50h
Read Status Register
05h
(S7–S0)(1)
Write Status Register
01h
S7–S0
Read Data
03h
A23–A16
A15–A8
A7–A0
(D7–D0)
(Next
byte)
continuous
Fast Read
0Bh
A23–A16
A15–A8
A7–A0
dummy
(D7–D0)
(Next Byte)
continuous
Fast Read Dual Output
3Bh
A23–A16
A15–A8
A7–A0
dummy
(D7-D0,
…)(5)
(one byte per 4
clocks, continuous)
Fast Read Dual I/O
BBh
A23-A8(6)
A7-A0, M7M0(6)
(D7-D0,
…)(5)
Page Program
02h
A23–A16
A15–A8
A7–A0
(D7–D0)
(Next
byte)
Up to 256 bytes
(2)
Sector Erase (4KB)
20h
A23–A16
A15–A8
A7–A0
Block Erase (32KB)
52h
A23–A16
A15–A8
A7–A0
Block Erase (64KB)
D8h
A23–A16
A15–A8
A7–A0
Chip Erase
C7h/60h
Power-down
B9h
Release Power-down /
Device ID
ABh
dummy
dummy
dummy
(ID7ID0)(4)
90h
dummy
dummy
00h
(M7-M0)
(ID7ID0)
Manufacturer/Device
ID by Dual I/O
92h
A23-A8
A7-A0, M[7:0]
(MF[7:0],
ID[7:0])
JEDEC ID
9Fh
(M7-M0)
Manufacturer
(ID15-ID8)
(ID7-ID0)
Memory Type Capacity
Read Unique ID
4Bh
dummy
dummy
dummy
(ID63ID0)
Manufacturer/
Device ID (3)
dummy
Read Unique ID
Notes:
1. Data bytes are shifted with Most Significant Bit first. Byte fields with data in parenthesis “( )” indicate data being read from the
device on the DO pin.
2. The Status Register contents will repeat continuously until /CS terminates the instruction.
3. See Manufacturer and Device Identification table for Device ID information.
4. The Device ID will repeat continuously until /CS terminates the instruction.
5. Dual Output and Dual I/O data
IO0 = (D6, D4, D2, D0)
IO1 = (D7, D5, D3, D1)
6. Dual Input Address
IO0 = A22, A20, A18, A16, A14, A12, A10, A8 A6, A4, A2, A0, M6, M4, M2, M0
IO1 = A23, A21, A19, A17, A15, A13, A11, A9 A7, A5, A3, A1, M7, M5, M3, M1
- 15 -
Publication Release Date: October 14, 2009
Preliminary -- Revision A
W25X10BL/20BL/40BL
9.2.3
Write Enable (06h)
The Write Enable instruction (Figure 4) sets the Write Enable Latch (WEL) bit in the Status Register to
a 1. The WEL bit must be set prior to every Page Program, Sector Erase, Block Erase, Chip Erase and
Write Status Register instruction. The Write Enable instruction is entered by driving /CS low, shifting
the instruction code “06h” into the Data Input (DI) pin on the rising edge of CLK, and then driving /CS
high.
Figure 4. Write Enable Instruction Sequence Diagram
9.2.4
Write Enable for Volatile Status Register (50h)
The non-volatile Status Register bits described in section 9.1 can also be written to as volatile bits. This
gives more flexibility to change the system configuration and memory protection schemes quickly
without waiting for the typical non-volatile bit write cycles or affecting the endurance of the Status
Register non-volatile bits. To write the volatile values into the Status Register bits, the Write Enable for
Volatile Status Register (50h) instruction must be issued prior to a Write Status Register (01h)
instruction. Write Enable for Volatile Status Register instruction (Figure 5) will not set the Write Enable
Latch (WEL) bit, it is only valid for the Write Status Register instruction to change the volatile Status
Register bit values.
Instruction (50h)
Figure 5. Write Enable for Volatile Status Register Instruction Sequence Diagram
- 16 -
W25X10BL/20BL/40BL
9.2.5
Write Disable (04h)
The Write Disable instruction (Figure 6) resets the Write Enable Latch (WEL) bit in the Status Register
to a 0. The Write Disable instruction is entered by driving /CS low, shifting the instruction code “04h”
into the DIO pin and then driving /CS high. Note that the WEL bit is automatically reset after Power-up
and upon completion of the Write Status Register, Page Program, Sector Erase, Block Erase and Chip
Erase instructions.
Figure 6. Write Disable Instruction Sequence Diagram
- 17 -
Publication Release Date: October 14, 2009
Preliminary -- Revision A
W25X10BL/20BL/40BL
9.2.6
Read Status Register (05h)
The Read Status Register instruction allows the 8-bit Status Register to be read. The instruction is
entered by driving /CS low and shifting the instruction code “05h” into the DIO pin on the rising edge of
CLK. The status register bits are then shifted out on the DO pin at the falling edge of CLK with most
significant bit (MSB) first as shown in figure 7. The Status Register bits are shown in figure 3 and
include the BUSY, WEL, BP2-BP0, TB and SRP bits (see description of the Status Register earlier in
this datasheet).
The Status Register instruction may be used at any time, even while a Program, Erase or Write Status
Register cycle is in progress. This allows the BUSY status bit to be checked to determine when the
cycle is complete and if the device can accept another instruction. The Status Register can be read
continuously, as shown in Figure 7. The instruction is completed by driving /CS high.
Figure 7. Read Status Register Instruction Sequence Diagram
- 18 -
W25X10BL/20BL/40BL
9.2.7
Write Status Register (01h)
The Write Status Register instruction allows the Status Register to be written. Only non-volatile Status
Register bits SRP, TB, BP2, BP1, BP0 (bits 7 thru 2 of Status Register) can be written to. All other
Status Register bit locations are read-only and will not be affected by the Write Status Register
instruction. The Status Register bits are shown in figure 3 and described in 9.1.
To write non-volatile Status Register bits, a standard Write Enable (06h) instruction must previously
have been executed for the device to accept the Write Status Register Instruction (Status Register bit
WEL must equal 1). Once write enabled, the instruction is entered by driving /CS low, sending the
instruction code “01h”, and then writing the status register data byte as illustrated in figure 8.
To write volatile Status Register bits, a Write Enable for Volatile Status Register (50h) instruction must
have been executed prior to the Write Status Register instruction (Status Register bit WEL remains 0).
Upon power off, the volatile Status Register bit values will be lost, and the non-volatile Status Register
bit values will be restored when power on again.
To complete the Write Status Register instruction, the /CS pin must be driven high after the eighth bit
of data that is clocked in. If this is not done the Write Status Register instruction will not be executed.
During non-volatile Status Register write operation (06h combined with 01h), after /CS is driven high,
the self-timed Write Status Register cycle will commence for a time duration of tW (See AC
Characteristics). While the Write Status Register cycle is in progress, the Read Status Register
instruction may still be accessed to check the status of the BUSY bit. The BUSY bit is a 1 during the
Write Status Register cycle and a 0 when the cycle is finished and ready to accept other instructions
again. After the Write Status Register cycle has finished, the Write Enable Latch (WEL) bit in the
Status Register will be cleared to 0.
During volatile Status Register write operation (50h combined with 01h), after /CS is driven high, the
Status Register bits will be refreshed to the new values within the time period of tSHSL2 (See AC
Characteristics). BUSY bit will remain 0 during the Status Register bit refresh period.
Please refer to 9.1 for detailed Status Register Bit descriptions. Factory default for all status Register
bits are 0.
.
- 19 -
Publication Release Date: October 14, 2009
Preliminary -- Revision A
W25X10BL/20BL/40BL
Figure 8. Write Status Register Instruction Sequence Diagram
- 20 -
W25X10BL/20BL/40BL
9.2.8
Read Data (03h)
The Read Data instruction allows one more data bytes to be sequentially read from the memory. The
instruction is initiated by driving the /CS pin low and then shifting the instruction code “03h” followed
by a 24-bit address (A23-A0) into the DIO pin. The code and address bits are latched on the rising
edge of the CLK pin. After the address is received, the data byte of the addressed memory location will
be shifted out on the DO pin at the falling edge of CLK with most significant bit (MSB) first. The
address is automatically incremented to the next higher address after each byte of data is shifted out
allowing for a continuous stream of data. This means that the entire memory can be accessed with a
single instruction as long as the clock continues. The instruction is completed by driving /CS high. The
Read Data instruction sequence is shown in figure 9. If a Read Data instruction is issued while an
Erase, Program or Write cycle is in process (BUSY=1) the instruction is ignored and will not have any
effects on the current cycle. The Read Data instruction allows clock rates from D.C. to a maximum of
fR (see AC Electrical Characteristics).
Figure 9. Read Data Instruction Sequence Diagram
- 21 -
Publication Release Date: October 14, 2009
Preliminary -- Revision A
W25X10BL/20BL/40BL
9.2.9
Fast Read (0Bh)
The Fast Read instruction is similar to the Read Data instruction except that it can operate at the
highest possible frequency of FR (see AC Electrical Characteristics). This is accomplished by adding
eight “dummy” clocks after the 24-bit address as shown in figure 10. The dummy clocks allow the
devices internal circuits additional time for setting up the initial address. During the dummy clocks the
data value on the DIO pin is a “don’t care”.
Figure 10. Fast Read Instruction Sequence Diagram
- 22 -
W25X10BL/20BL/40BL
9.2.10 Fast Read Dual Output (3Bh)
The Fast Read Dual Output (3Bh) instruction is similar to the standard Fast Read (0Bh) instruction
except that data is output on two pins, DO and DIO, instead of just DO. This allows data to be
transferred from the W25X10BL/20BL/40BL at twice the rate of standard SPI devices. The Fast Read
Dual Output instruction is ideal for quickly downloading code from Flash to RAM upon power-up or for
applications that cache code-segments to RAM for execution.
Similar to the Fast Read instruction, the Fast Read Dual Output instruction can operate at the highest
possible frequency of FR (see AC Electrical Characteristics). This is accomplished by adding eight
“dummy” clocks after the 24-bit address as shown in figure 11. The dummy clocks allow the device's
internal circuits additional time for setting up the initial address. The input data during the dummy
clocks is “don’t care”. However, the DIO pin should be high-impedance prior to the falling edge of the
first data out clock.
Figure 11. Fast Read Dual Output Instruction Sequence Diagram
- 23 -
Publication Release Date: October 14, 2009
Preliminary -- Revision A
W25X10BL/20BL/40BL
9.2.11
Fast Read Dual I/O (BBh)
The Fast Read Dual I/O (BBh) instruction allows for improved random access while maintaining two IO
pins, IO 0 and IO 1 . It is similar to the Fast Read Dual Output (3Bh) instruction but with the capability to
input the Address bits (A23-0) two bits per clock. This reduced instruction overhead may allow for code
execution (XIP) directly from the Dual SPI in some applications.
Fast Read Dual I/O with “Continuous Read Mode”
The Fast Read Dual I/O instruction can further reduce instruction overhead through setting the
“Continuous Read Mode” bits (M7-0) after the input Address bits (A23-0), as shown in figure 12a. The
upper nibble of the (M7-4) controls the length of the next Fast Read Dual I/O instruction through the
inclusion or exclusion of the first byte instruction code. The lower nibble bits of the (M3-0) are don’t
care (“x”). However, the IO pins should be high-impedance prior to the falling edge of the first data out
clock.
If the “Continuous Read Mode” bits M5-4 = (1,0), then the next Fast Read Dual I/O instruction (after
/CS is raised and then lowered) does not require the BBh instruction code, as shown in figure 12b. This
reduces the instruction sequence by eight clocks and allows the Read address to be immediately
entered after /CS is asserted low. If the “Continuous Read Mode” bits M5-4 do not equal to (1,0), the
next instruction (after /CS is raised and then lowered) requires the first byte instruction code, thus
returning to normal operation. A “Continuous Read Mode” Reset instruction can also be used to reset
(M7-0) before issuing normal instructions (See 9.2.13 for detail descriptions).
Figure 12a. Fast Read Dual I/O Instruction Sequence (Initial instruction or previous M5-4 ≠ 10)
- 24 -
W25X10BL/20BL/40BL
Figure 12b. Fast Read Dual I/O Instruction Sequence (Previous instruction set M5-4 = 10)
- 25 -
Publication Release Date: October 14, 2009
Preliminary -- Revision A
W25X10BL/20BL/40BL
9.2.12
Continuous Read Mode Bits (M7-0)
The “Continuous Read Mode” bits are used in conjunction with the “Fast Read Dual I/O” instruction to
provide the highest random Flash memory access rate with minimum SPI instruction overhead, thus
allow true XIP (execute in place) to be performed on serial flash devices.
M7-0 need to be set by the Dual I/O Read instruction. M5-4 are used to control whether the 8-bit SPI
instruction code BBh is needed or not for the next command. When M5-4 = (1,0), the next command
will be treated same as the current Dual I/O Read command without needing the 8-bit instruction code;
when M5-4 do not equal to (1,0), the device returns to normal SPI mode, all commands can be
accepted. M7-6 and M3-0 are reserved bits for future use, either 0 or 1 values can be used.
9.2.13
Continuous Read Mode Reset (FFFFh)
Continuous Read Mode Reset instruction can be used to set M4 = 1, thus the device will release the
Continuous Read Mode and return to normal SPI operation, as shown in figure 13.
Mode Bit Reset
for Dual I/O
/CS
Mode 3
CLK
IO 0
IO 1
0
1
2
3
4
5
6
7
8
9
10
11
12
13
Mode 0
14
15
Mode 3
Mode 0
FFFFh
Don’t Care
Figure 13. Continuous Read Mode Reset for Fast Read Dual I/O
Since W25X10BL/20BL/40BL does not have a hardware Reset pin, so if the controller resets while
W25X10BL/20BL/40BL are set to Continuous Mode Read, the W25X10BL/20BL/40BL will
not recognize any initial standard SPI instructions from the controller. To address this possibility, it is
recommended to issue a Continuous Read Mode Reset instruction as the first instruction after a
system Reset. Doing so will release the device from the Continuous Read Mode and allow Standard
SPI instructions to be recognized.
To reset “Continuous Read Mode” during Dual I/O operation, sixteen clocks are needed to shift in
instruction “FFFFh”.
- 26 -
W25X10BL/20BL/40BL
9.2.14 Page Program (02h)
The Page Program instruction allows up to 256 bytes of data to be programmed at previously erased to
all 1s (FFh) memory locations. A Write Enable instruction must be executed before the device will
accept the Page Program Instruction (Status Register bit WEL must equal 1). The instruction is
initiated by driving the /CS pin low then shifting the instruction code “02h” followed by a 24-bit address
(A23-A0) and at least one data byte, into the DIO pin. The /CS pin must be held low for the entire
length of the instruction while data is being sent to the device.
If an entire 256 byte page is to be programmed, the last address byte (the 8 least significant address
bits) should be set to 0. If the last address byte is not zero, and the number of clocks exceed the
remaining page length, the addressing will wrap to the beginning of the page. In some cases, less than
256 bytes (a partial page) can be programmed without having any effect on other bytes within the
same page. One condition to perform a partial page program is that the number of clocks cannot
exceed the remaining page length. If more than 256 bytes are sent to the device the addressing will
wrap to the beginning of the page and overwrite previously sent data.
As with the write and erase instructions, the /CS pin must be driven high after the eighth bit of the last
byte has been latched. If this is not done the Page Program instruction will not be executed. After /CS
is driven high, the self-timed Page Program instruction will commence for a time duration of tpp (See
AC Characteristics). While the Page Program cycle is in progress, the Read Status Register instruction
may still be accessed for checking the status of the BUSY bit. The BUSY bit is a 1 during the Page
Program cycle and becomes a 0 when the cycle is finished and the device is ready to accept other
instructions again. After the Page Program cycle has finished the Write Enable Latch (WEL) bit in the
Status Register is cleared to 0. The Page Program instruction will not be executed if the addressed
page is protected by the Block Protect (BP2, BP1, and BP0) bits (see Status Register Memory
Protection table).
Figure 14. Page Program Instruction Sequence Diagram
- 27 -
Publication Release Date: October 14, 2009
Preliminary -- Revision A
W25X10BL/20BL/40BL
9.2.15
Sector Erase (20h)
The Sector Erase instruction sets all memory within a specified sector (4K-bytes) to the erased state of
all 1s (FFh). A Write Enable instruction must be executed before the device will accept the Sector
Erase Instruction (Status Register bit WEL must equal 1). The instruction is initiated by driving the /CS
pin low and shifting the instruction code “20h” followed a 24-bit sector address (A23-A0) (see Figure 2).
The Sector Erase instruction sequence is shown in figure 15.
The /CS pin must be driven high after the eighth bit of the last byte has been latched. If this is not done
the Sector Erase instruction will not be executed. After /CS is driven high, the self-timed Sector Erase
instruction will commence for a time duration of tSE (See AC Characteristics). While the Sector Erase
cycle is in progress, the Read Status Register instruction may still be accessed for checking the status
of the BUSY bit. The BUSY bit is a 1 during the Sector Erase cycle and becomes a 0 when the cycle is
finished and the device is ready to accept other instructions again. After the Sector Erase cycle has
finished the Write Enable Latch (WEL) bit in the Status Register is cleared to 0. The Sector Erase
instruction will not be executed if the addressed page is protected by the Block Protect (TB, BP2, BP1,
and BP0) bits (see Status Register Memory Protection table).
Figure 15. Sector Erase Instruction Sequence Diagram
- 28 -
W25X10BL/20BL/40BL
9.2.16
32KB Block Erase (52h)
The Block Erase instruction sets all memory within a specified block (32K-bytes) to the erased state of
all 1s (FFh). A Write Enable instruction must be executed before the device will accept the Block Erase
Instruction (Status Register bit WEL must equal 1). The instruction is initiated by driving the /CS pin low
and shifting the instruction code “52h” followed a 24-bit block address (A23-A0) (see Figure 2). The
Block Erase instruction sequence is shown in figure 16.
The /CS pin must be driven high after the eighth bit of the last byte has been latched. If this is not done
the Block Erase instruction will not be executed. After /CS is driven high, the self-timed Block Erase
instruction will commence for a time duration of tBE1 (See AC Characteristics). While the Block Erase
cycle is in progress, the Read Status Register instruction may still be accessed for checking the status
of the BUSY bit. The BUSY bit is a 1 during the Block Erase cycle and becomes a 0 when the cycle is
finished and the device is ready to accept other instructions again. After the Block Erase cycle has
finished the Write Enable Latch (WEL) bit in the Status Register is cleared to 0. The Block Erase
instruction will not be executed if the addressed page is protected by the Block Protect (SEC, TB, BP2,
BP1, and BP0) bits (see Status Register Memory Protection table).
Figure 16. 32KB Block Erase Instruction Sequence Diagram
- 29 -
Publication Release Date: October 14, 2009
Preliminary -- Revision A
W25X10BL/20BL/40BL
9.2.17
Block Erase (D8h)
The Block Erase instruction sets all memory within a specified block (64K-bytes) to the erased state of
all 1s (FFh). A Write Enable instruction must be executed before the device will accept the Block Erase
Instruction (Status Register bit WEL must equal 1). The instruction is initiated by driving the /CS pin low
and shifting the instruction code “D8h” followed a 24-bit block address (A23-A0) (see Figure 2). The
Block Erase instruction sequence is shown in figure 17.
The /CS pin must be driven high after the eighth bit of the last byte has been latched. If this is not done
the Block Erase instruction will not be executed. After /CS is driven high, the self-timed Block Erase
instruction will commence for a time duration of tBE (See AC Characteristics). While the Block Erase
cycle is in progress, the Read Status Register instruction may still be accessed for checking the status
of the BUSY bit. The BUSY bit is a 1 during the Block Erase cycle and becomes a 0 when the cycle is
finished and the device is ready to accept other instructions again. After the Block Erase cycle has
finished the Write Enable Latch (WEL) bit in the Status Register is cleared to 0. The Block Erase
instruction will not be executed if the addressed page is protected by the Block Protect (TB, BP2, BP1,
and BP0) bits (see Status Register Memory Protection table).
Figure 17. Block Erase Instruction Sequence Diagram
- 30 -
W25X10BL/20BL/40BL
9.2.18
Chip Erase (C7h or 60h)
The Chip Erase instruction sets all memory within the device to the erased state of all 1s (FFh). A
Write Enable instruction must be executed before the device will accept the Chip Erase Instruction
(Status Register bit WEL must equal 1). The instruction is initiated by driving the /CS pin low and
shifting the instruction code “C7h” or “60h”. The Chip Erase instruction sequence is shown in figure 18.
The /CS pin must be driven high after the eighth bit has been latched. If this is not done the Chip Erase
instruction will not be executed. After /CS is driven high, the self-timed Chip Erase instruction will
commence for a time duration of tCE (See AC Characteristics). While the Chip Erase cycle is in
progress, the Read Status Register instruction may still be accessed to check the status of the BUSY
bit. The BUSY bit is a 1 during the Chip Erase cycle and becomes a 0 when finished and the device is
ready to accept other instructions again. After the Chip Erase cycle has finished the Write Enable Latch
(WEL) bit in the Status Register is cleared to 0. The Chip Erase instruction will not be executed if any
page is protected by the Block Protect (BP2, BP1, and BP0) bits (see Status Register Memory
Protection table).
Figure 18. Chip Erase Instruction Sequence Diagram
- 31 -
Publication Release Date: October 14, 2009
Preliminary -- Revision A
W25X10BL/20BL/40BL
9.2.19
Power-down (B9h)
Although the standby current during normal operation is relatively low, standby current can be further
reduced with the Power-down instruction. The lower power consumption makes the Power-down
instruction especially useful for battery powered applications (See ICC1 and ICC2 in AC
Characteristics). The instruction is initiated by driving the /CS pin low and shifting the instruction code
“B9h” as shown in figure 19.
The /CS pin must be driven high after the eighth bit has been latched. If this is not done the Powerdown instruction will not be executed. After /CS is driven high, the power-down state will entered within
the time duration of tDP (See AC Characteristics). While in the power-down state only the Release from
Power-down / Device ID instruction, which restores the device to normal operation, will be recognized.
All other instructions are ignored. This includes the Read Status Register instruction, which is always
available during normal operation. Ignoring all but one instruction makes the Power Down state a
useful condition for securing maximum write protection. The device always powers-up in the normal
operation with the standby current of ICC1.
Figure 19. Deep Power-down Instruction Sequence Diagram
- 32 -
W25X10BL/20BL/40BL
9.2.20
Release Power-down / Device ID (ABh)
The Release from Power-down / Device ID instruction is a multi-purpose instruction. It can be used to
release the device from the power-down state, obtain the devices electronic identification (ID) number
or do both.
When used only to release the device from the power-down state, the instruction is issued by driving
the /CS pin low, shifting the instruction code “ABh” and driving /CS high as shown in figure 20. After the
time duration of tRES1 (See AC Characteristics) the device will resume normal operation and other
instructions will be accepted. The /CS pin must remain high during the tRES1 time duration.
When used only to obtain the Device ID while not in the power-down state, the instruction is initiated by
driving the /CS pin low and shifting the instruction code “ABh” followed by 3-dummy bytes. The Device
ID bits are then shifted out on the falling edge of CLK with most significant bit (MSB) first as shown in
figure 20. The Device ID values for the W25X10BL/20BL/40BL are listed in Manufacturer and Device
Identification table. The Device ID can be read continuously. The instruction is completed by driving
/CS high.
When used to release the device from the power-down state and obtain the Device ID, the instruction
is the same as previously described, and shown in figure 21, except that after /CS is driven high it must
remain high for a time duration of tRES2 (See AC Characteristics). After this time duration the device
will resume normal operation and other instructions will be accepted.
If the Release from Power-down / Device ID instruction is issued while an Erase, Program or Write
cycle is in process (when BUSY equals 1) the instruction is ignored and will not have any effects on the
current cycle
Figure 20. Release Power-down Instruction Sequence
- 33 -
Publication Release Date: October 14, 2009
Preliminary -- Revision A
W25X10BL/20BL/40BL
Figure 21. Release Power-down / Device ID Instruction Sequence Diagram
- 34 -
W25X10BL/20BL/40BL
9.2.21 Read Manufacturer / Device ID (90h)
The Read Manufacturer/Device ID instruction is an alternative to the Release from Power-down/
Device ID instruction that provides both JEDEC assigned manufacturer ID and the specific device ID.
The Read Manufacturer/Device ID instruction is very similar to the Release from Power-down / Device
ID instruction. The instruction is initiated by driving the /CS pin low and shifting the instruction code
“90h” followed by a 24-bit address (A23-A0) of 000000h. After which, the Manufacturer ID for Winbond
(EFh) and the Device ID are shifted out on the falling edge of CLK with most significant bit (MSB) first
as shown in figure 22. The Device ID values for the W25X10BL/20BL/40BL are listed in Manufacturer
and Device Identification table. If the 24-bit address is initially set to 000001h the Device ID will be read
first and then followed by the Manufacturer ID. The Manufacturer and Device IDs can be read
continuously, alternating from one to the other. The instruction is completed by driving /CS high.
31 32
33 34 35
36 37 38 39
40 41 42
43 44
45 46
Figure 22. Read Manufacturer / Device ID Diagram
- 35 -
Publication Release Date: October 14, 2009
Preliminary -- Revision A
W25X10BL/20BL/40BL
9.2.22
Read Manufacturer / Device ID Dual I/O (92h)
The Manufacturer / Device ID Dual I/O instruction is an alternative to the Read Manufacturer/Device ID
instruction that provides both the JEDEC assigned manufacturer ID and the specific device ID at 2x
speed.
The Read Manufacturer / Device ID Dual I/O instruction is similar to the Fast Read Dual I/O instruction.
The instruction is initiated by driving the /CS pin low and shifting the instruction code “92h” followed by
a 24-bit address (A23-A0) of 000000h, but with the capability to input the Address bits two bits per
clock. After which, the Manufacturer ID for Winbond (EFh) and the Device ID are shifted out 2 bits per
clock on the falling edge of CLK with most significant bits (MSB) first as shown in figure 23. The Device
ID values for the W25X10BL/20BL/40BL are listed in Manufacturer and Device Identification table. If
the 24-bit address is initially set to 000001h the Device ID will be read first and then followed by the
Manufacturer ID. The Manufacturer and Device IDs can be read continuously, alternating from one to
the other. The instruction is completed by driving /CS high.
Figure 23. Read Manufacturer / Device ID Dual I/O Diagram
Note:
The “Continuous Read Mode” bits M7-0 must be set to Fxh to be compatible with Fast Read Dual I/O instruction.
- 36 -
W25X10BL/20BL/40BL
9.2.23
Read Unique ID Number (4Bh)
The Read Unique ID Number instruction accesses a factory-set read-only 64-bit number that is unique
to each W25X10BL/20BL/40BL device. The ID number can be used in conjunction with user software
methods to help prevent copying or cloning of a system. The Read Unique ID instruction is initiated by
driving the /CS pin low and shifting the instruction code “4Bh” followed by a four bytes of dummy
clocks. After which, the 64-bit ID is shifted out on the falling edge of CLK as shown in figure 24.
DO
24 25
26
27 28
29 30
31 32 33
34
35 36
37 38
39
40
*
DO
41
42 43 44 101 102 103
63 62 61 60 59
2
1
0
*=MSB
Figure 24. Read Unique ID Number Instruction Sequence
- 37 -
Publication Release Date: October 14, 2009
Preliminary -- Revision A
W25X10BL/20BL/40BL
9.2.24 JEDEC ID (9Fh)
For compatibility reasons, the W25X10BL/20BL/40BL provides several instructions to electronically
determine the identity of the device. The Read JEDEC ID instruction is compatible with the JEDEC
standard for SPI compatible serial memories that was adopted in 2003.
The instruction is initiated by driving the /CS pin low and shifting the instruction code “9Fh”. The
JEDEC assigned Manufacturer ID byte for Winbond (EFh) and two Device ID bytes, Memory Type
(ID15-ID8) and Capacity (ID7-ID0) are then shifted out on the falling edge of CLK with most significant
bit (MSB) first as shown in figure 25. For memory type and capacity values refer to Manufacturer and
Device Identification table.
15
16
17
18
19
20
21
22
23
24
25
26
Figure 25. Read JEDEC ID
- 38 -
27
28
29
30 31
W25X10BL/20BL/40BL
10. ELECTRICAL CHARACTERISTICS(1)
10.1 Absolute Maximum Ratings (2)
PARAMETERS
SYMBOL
Supply Voltage
VCC
Voltage Applied to Any Pin
VIO
Transient Voltage on any Pin
VIOT
Storage Temperature
TSTG
Lead Temperature
CONDITIONS
RANGE
–0.6 to +4.0
V
Relative to Ground
–0.6 to VCC +0.4
V
<20nS Transient
Relative to Ground
–2.0V to VCC+2.0V
V
–65 to +150
°C
(3)
°C
TLEAD
Electrostatic Discharge Voltage
VESD
UNIT
See Note
Human Body
Model(4)
–2000 to +2000
V
Notes:
1. Specification for W25X10BL/20BL/40BL are preliminary. See preliminary designation at the end of
this document.
2. This device has been designed and tested for the specified operation ranges. Proper operation
outside of these levels is not guaranteed. Exposure to absolute maximum ratings may affect device
reliability. Exposure beyond absolute maximum ratings may cause permanent damage.
3. Compliant with JEDEC Standard J-STD-20C for small body Sn-Pb or Pb-free (Green) assembly and
the European directive on restrictions on hazardous substances (RoHS) 2002/95/EU.
4. JEDEC Std JESD22-A114A (C1=100 pF, R1=1500 ohms, R2=500 ohms).
10.2 Operating Ranges
PARAMETER
Supply Voltage(1)
Ambient Temperature,
Operating
SYMBOL
VCC
TA
SPEC
CONDITIONS
UNIT
MIN
MAX
F R = 50MHz, fR = 25MHz
2.3
3.6
V
Industrial
Commercial
–40
0
+85
+70
°C
Note:
1. VCC voltage during Read can operate across the min and max range but should not exceed ±10%
of the programming (erase/write) voltage.
- 39 -
Publication Release Date: October 14, 2009
Preliminary -- Revision A
W25X10BL/20BL/40BL
10.3 Power-up Timing and Write Inhibit Threshold
SPEC
PARAMETER
SYMBOL
VCC (min) to /CS Low
tVSL(1)
10
Time Delay Before Write Instruction
tPUW
1
10
ms
Write Inhibit Threshold Voltage
VWI
1
2
V
(1)
(1)
MIN
Note:
1. These parameters are characterized only.
Figure 26. Power-up Timing and Voltage Levels
- 40 -
MAX
UNIT
µs
W25X10BL/20BL/40BL
10.4 DC Electrical Characteristics
PARAMETER
SYMBOL CONDITIONS
Input Capacitance
CIN(1)
VIN = 0V(2)
Output Capacitance
Cout
VOUT = 0V
Input Leakage
SPEC
MIN
TYP
MAX
UNIT
6
pF
8
pF
ILI
±2
µA
I/O Leakage
ILO
±2
µA
Standby Current
ICC1
/CS = VCC,
VIN = GND or VCC
25
50
µA
Power-down Current
ICC2
/CS = VCC,
VIN = GND or VCC
1
5
µA
Current Read Data /
Dual Output 1MHz(2)
ICC3
C = 0.1 VCC / 0.9 VCC
DO = Open
4/5
6/7.5
mA
Current Read Data /
Dual Output 33MHz(2)
ICC3
C = 0.1 VCC / 0.9 VCC
DO = Open
6/7
9/10
mA
Current Read Data /
Dual Output 50MHz(2)
ICC3
C = 0.1 VCC / 0.9 VCC
DO = Open
7/8
10/12
mA
Current Write Status
Register
ICC4
/CS = VCC
8
12
mA
Current Page Program
ICC5
/CS = VCC
20
25
mA
Current Sector/Block
Erase
ICC6
/CS = VCC
20
25
mA
Current Chip Erase
ICC7
/CS = VCC
20
25
mA
Input Low Voltage
VIL
–0.5
VCCx0.3
V
Input High Voltage
VIH
VCCx0.7
VCC+0.4
V
Output Low Voltage
VOL
IOL = 1.6 mA
0.4
V
Output High Voltage
VOH
IOH = –100 µA
(1)
(2)
VCC–0.2
V
Notes:
1. Tested on sample basis and specified through design and characterization data. TA=25°C, VCC=3V.
2. Checker Board Pattern.
- 41 -
Publication Release Date: October 14, 2009
Preliminary -- Revision A
W25X10BL/20BL/40BL
10.5 AC Measurement Conditions
PARAMETER
SYMBOL
Load Capacitance
Input Rise and Fall Times
Input Pulse Voltages
Input Timing Reference Voltages
Output Timing Reference Voltages
SPEC
MIN
MAX
UNIT
CL
30
pF
TR, TF
5
ns
VIN
0.2 VCC to 0.8 VCC
V
IN
0.3 VCC to 0.7 VCC
V
OUT
0.5 VCC to 0.5 VCC
V
Note:
1. Output Hi-Z is defined as the point where data out is no longer driven.
Figure 27. AC Measurement I/O Waveform
- 42 -
W25X10BL/20BL/40BL
10.6 AC Electrical Characteristics
SPEC
DESCRIPTION
SYMBOL
ALT
UNIT
MIN
Clock frequency for all instructions,
except Read Data (03h)
2.3V-3.6V VCC & Industrial Temperature
FR
Clock freq. Read Data instruction 03h
TYP
MAX
D.C.
50
MHz
fR
D.C.
25
MHz
Clock High, Low Time, for Fast Read (0Bh, 3Bh) /
other instructions except Read Data (03h)
tCLH,
tCLL(1)
4
ns
Clock High, Low Time for Read Data (03h)
instruction
tCRLH,
tCRLL(1)
8
ns
Clock Rise Time peak to peak
tCLCH(2)
0.1
V/ns
Clock Fall Time peak to peak
tCHCL(2)
0.1
V/ns
5
ns
5
ns
fc
/CS Active Setup Time relative to CLK
tSLCH
/CS Not Active Hold Time relative to CLK
tCHSL
Data In Setup Time
tDVCH
tDSU
2
ns
Data In Hold Time
tCHDX
tDH
5
ns
/CS Active Hold Time relative to CLK
tCHSH
5
ns
/CS Not Active Setup Time relative to CLK
tSHCH
5
ns
/CS Deselect Time (for Array Read  Array Read)
tSHSL1
tCSH
10
ns
/CS Deselect Time (for Erase or Program  Read
Status Registers and Volatile Status Register Write)
tSHSL2
tCSH
50
ns
tSHQZ(2)
tDIS
7
ns
Clock Low to Output Valid
tCLQV
tV
7
ns
Output Hold Time
tCLQX
tHO
Output Disable Time
tCSS
0
ns
Continued – next page
- 43 -
Publication Release Date: October 14, 2009
Preliminary -- Revision A
W25X10BL/20BL/40BL
10.7 AC Electrical Characteristics (cont’d)
SPEC
DESCRIPTION
SYMBOL
ALT
UNIT
MIN
TYP
MAX
/HOLD Active Setup Time relative to CLK
tHLCH
5
ns
/HOLD Active Hold Time relative to CLK
tCHHH
5
ns
/HOLD Not Active Setup Time relative to CLK
tHHCH
5
ns
/HOLD Not Active Hold Time relative to CLK
tCHHL
5
ns
/HOLD to Output Low-Z
tHHQX(2)
tLZ
7
ns
/HOLD to Output High-Z
tHLQZ(2)
tHZ
12
ns
Write Protect Setup Time Before /CS Low
tWHSL(3)
20
ns
Write Protect Hold Time After /CS High
tSHWL(3)
100
ns
tDP(2)
3
µs
/CS High to Standby Mode without Electronic
Signature Read
tRES1(2)
3
µs
/CS High to Standby Mode with Electronic
Signature Read
tRES2(2)
1.8
µs
/CS High to Power-down Mode
Write Status Register Time
tW
10
15
ms
Byte Program Time (First Byte) (4)
t BP1
30
50
µs
Additional Byte Program Time (After First Byte) (4)
t BP2
2.5
12
µs
Page Program Time
tPP
0.7
3
ms
Sector Erase Time (4KB)
tSE
30
200
ms
Block Erase Time (32KB)
tBE 1
120
800
ms
Block Erase Time (64KB)
tBE 2
150
1,000
ms
Chip Erase Time W25X10BL / W25X20BL
Chip Erase Time W25X40BL
tCE
0.5
1
2
4
s
Notes:
1.
Clock high + Clock low must be less than or equal to 1/fC.
2.
Value guaranteed by design and/or characterization, not 100% tested in production.
3.
Only applicable as a constraint for a Write Status Register instruction when SRP is set to 1.
4.
For multiple bytes after first byte within a page, t BPN = t BP1 + t BP2 * N (typical) and t BPN = t BP1 + t BP2 * N (max),
where N = number of bytes programmed.
- 44 -
W25X10BL/20BL/40BL
10.8 Serial Output Timing
10.9 Input Timing
10.10 Hold Timing
- 45 -
Publication Release Date: October 14, 2009
Preliminary -- Revision A
W25X10BL/20BL/40BL
11. PACKAGE SPECIFICATION
11.1 8-Pin SOIC 150-mil (Package Code SN)
1
SYMBOL
A
A1
b
c
E(3)
D(3)
e(2)
HE
Y(4)
L
θ
MILLIMETERS
Min
Max
1.35
0.10
0.33
0.19
3.80
4.80
1.75
0.25
0.51
0.25
4.00
5.00
1.27 BSC
5.80
0.40
0°
6.20
0.10
1.27
10°
INCHES
Min
Max
0.053
0.069
0.004
0.010
0.013
0.020
0.008
0.010
0.150
0.157
0.188
0.196
0.050 BSC
0.228
0.244
0.004
0.016
0.050
0°
10°
Notes:
1. Controlling dimensions: millimeters, unless otherwise specified.
2. BSC = Basic lead spacing between centers.
3. Dimensions D and E do not include mold flash protrusions and should be measured from the bottom of the package.
4. Formed leads coplanarity with respect to seating plane shall be within 0.004 inches.
- 46 -
W25X10BL/20BL/40BL
11.2 8-Pin SOIC 208-mil (Package Code SS)
SYMBOL
A
A1
A2
b
C
D
D1
E
E1
e
H
L
y
θ
MILLIMETERS
INCHES
MIN
NOM
MAX
MIN
NOM
MAX
1.75
0.05
1.70
0.35
0.19
5.18
5.13
5.18
5.13
1.95
0.15
1.80
0.42
0.20
5.28
5.23
5.28
5.23
1.27 BSC
7.90
0.65
-
2.16
0.25
1.91
0.48
0.25
5.38
5.33
5.38
5.33
0.069
0.002
0.067
0.014
0.007
0.204
0.202
0.204
0.202
0.085
0.010
0.075
0.019
0.010
0.212
0.210
0.212
0.210
8.10
0.80
0.010
8°
0.303
0.020
0°
0.077
0.006
0.071
0.017
0.008
0.208
0.206
0.208
0.206
0.050 BSC
0.311
0.026
-
7.70
0.50
0°
0.319
0.031
0.004
8°
Notes:
1. Controlling dimensions: millimeters, unless otherwise specified.
2. BSC = Basic lead spacing between centers.
3. Dimensions D1 and E1 do not include mold flash protrusions and should be measured from the bottom of the package.
4. Formed leads coplanarity with respect to seating plane shall be within 0.004 inches.
- 47 -
Publication Release Date: October 14, 2009
Preliminary -- Revision A
W25X10BL/20BL/40BL
11.3 8-Pin PDIP 300-mil (Package Code DA)
Millimeters
Inches
Symbol
Min
Typ.
Max
Min
Typ.
Max
A
---
---
4.45
---
---
0.175
A1
0.25
---
---
0.010
---
---
A2
3.18
3.30
3.43
0.125
0.130
0.135
B
0.41
0.46
0.56
0.016
0.018
0.022
B1
1.47
1.52
1.63
0.058
0.060
0.064
c
0.20
0.25
0.36
0.008
0.010
0.014
D
-
9.14
9.65
-
0.360
0.380
0.310
E
7.37
7.62
7.87
0.290
0.300
E1
6.22
6.35
6.48
0.245
0.250
0.255
e1
2.29
2.54
2.79
0.090
0.100
0.110
L
3.05
3.30
3.56
0.120
0.130
0.140
α
0
-
15
0
-
15
eA
8.51
9.02
9.53
0.335
0.355
0.375
S
---
---
1.14
---
---
0.045
- 48 -
W25X10BL/20BL/40BL
11.4 8-Contact 6x5mm WSON (Package Code ZP)
SYMBOL
MILLIMETERS
INCHES
MIN
TYP.
MAX
MIN
TYP.
MAX
A
0.70
0.75
0.80
0.0275
0.0295
0.0314
A1
0.00
0.02
0.05
0.0000
0.0007
0.0019
b
0.35
0.40
0.48
0.0137
0.0157
0.0188
C
-
0.20 REF.
-
-
0.0078 REF.
-
D
5.90
6.00
6.10
0.2322
0.2362
0.2401
D2
3.35
3.40
3.45
0.1318
0.1338
0.1358
E
4.90
5.00
5.10
0.1929
0.1968
0.2007
E2
4.25
4.30
4.35
0.1673
0.1692
0.1712
E(2)
1.27 BSC
0.0500 BSC
L
0.55
0.60
0.65
0.0216
0.0236
0.0255
y
0.00
-
0.75
0.0000
-
0.0029
- 49 -
Publication Release Date: October 14, 2009
Preliminary -- Revision A
W25X10BL/20BL/40BL
8-Pad WSON 6x5mm Cont’d.
MILLIMETERS
INCHES
SYMBOL
MIN
TYP.
MAX
MIN
TYP.
MAX
SOLDER PATTERN
M
3.40
0.1338
N
4.30
0.1692
P
6.00
0.2360
Q
0.50
0.0196
R
0.75
0.0255
Notes:
1. Advanced Packaging Information; please contact Winbond for the latest minimum and maximum specifications.
2. BSC = Basic lead spacing between centers.
3. Dimensions D and E do not include mold flash protrusions and should be measured from the bottom of the package.
4. The metal pad area on the bottom center of the package is connected to the device ground (GND pin). Avoid placement of
exposed PCB vias under the pad.
- 50 -
W25X10BL/20BL/40BL
12. ORDERING INFORMATION(1)
W
W
=
Winbond
25X =
40
20
10
=
=
=
L =
25X xxB L xx(2)
spiFlash Serial Flash Memory with 4KB sectors, Dual Outputs
4M-bit
2M-bit
1M-bit
2.3V to 3.6V
SN = 8-pin SOIC 150-mil
SS = 8 pin SOIC 208-mil
ZP
DA
= 8-pad WSON 6x5mm
= 8-pin PDIP 300mil
I
=
Industrial (-40°C to +85°C)
G
= Green Package (Lead-free, RoHS Compliant, Halogen-free (TBBA), Antimony-Oxide-free Sb2O3)
Notes:
1a. Standard bulk shipments are in Tube (shape E). Please specify alternate packing method, such as Tape and Reel
(shape T) or Tray (shape S), when placing orders.
1b. The “W” prefix is not included on the part marking.
2.
Only the 2nd letter is used for the part marking, package type ZP is not used for the part marking.
- 51 -
Publication Release Date: October 14, 2009
Preliminary -- Revision A
W25X10BL/20BL/40BL
12.1 Valid Part Numbers and Top Side Marking
The following table provides the valid part numbers for the W25X10BL/20BL/40BL SpiFlash Memories.
Please contact Winbond for specific availability by density and package type. Winbond SpiFlash
memories use an 12-digit Product Number for ordering. However, due to limited space, the Top Side
Marking on all packages use an abbreviated 10-digit number.
PACKAGE TYPE
SN
SOIC-8 150mil
SS
SOIC-8 208mil
(1)
ZP
WSON-8 6x5mm
DA
PDIP-8 300mil
DENSITY
PRODUCT NUMBER
TOP SIDE MARKING
1M-bit
W25X10BLSNIG
25X10BLNIG
2M-bit
W25X20BLSNIG
25X20BLNIG
4M-bit
W25X40BLSNIG
25X40BLNIG
4M-bit
W25X40BLSSIG
25X40BLSIG
1M-bit
W25X10BLZPIG
25X10BLIG
2M-bit
W25X20BLZPIG
25X20BLIG
4M-bit
W25X40BLZPIG
25X40BLIG
4M-bit
W25X40BLDAIG
25X40BLAIG
Notes:
1. For WSON packages, the package type ZP is not used in the top side marking.
- 52 -
W25X10BL/20BL/40BL
13. REVISION HISTORY
VERSION
DATE
PAGE
A
10/14/09
All
DESCRIPTION
New create preliminary.
Preliminary Designation
The “Preliminary” designation on a Winbond datasheet indicates that the product is not fully
characterized. The specifications are subject to change and are not guaranteed. Winbond or an
authorized sales representative should be consulted for current information before using this product.
Trademarks
Winbond and SpiFlash are trademarks of Winbond Electronics Corporation.
All other marks are the property of their respective owner.
Important Notice
Winbond products are not designed, intended, authorized or warranted for use as components
in systems or equipment intended for surgical implantation, atomic energy control instruments,
airplane or spaceship instruments, transportation instruments, traffic signal instruments,
combustion control instruments, or for other applications intended to support or sustain life.
Further more, Winbond products are not intended for applications wherein failure of Winbond
products could result or lead to a situation wherein personal injury, death or severe property or
environmental damage could occur. Winbond customers using or selling these products for
use in such applications do so at their own risk and agree to fully indemnify Winbond for any
damages resulting from such improper use or sales.
Information in this document is provided solely in connection with Winbond products.
Winbond reserves the right to make changes, corrections, modifications or improvements to
this document and the products and services described herein at any time, without notice.
- 53 -
Publication Release Date: October 14, 2009
Preliminary -- Revision A