AGAMEM AA8600AP

AA8600AP
Agamem Microelectronics Inc.
___________________________________________________________
PRELIMINARY
Y/C MIX
„ FEATURE
1. Y/C mix circuit
2. Output and Chrominance muting function
3. Output protection function
4. SAG correction function
5. A load sufficient for driving two circuits
6. Low power consumption, 60mw typical
7. Internal voltage clamp circuit
„
APPLICATION
¾ VCR
¾ Video Camera
¾ TV
¾ Video Player
„ DESCRIPTION
AA8600AP is a Y/C mix with 6db gain, 75Ω output buffer and SAG correction.
The 75Ω buffer is capable of driving two circuits. The SAG could reduce the
capacitance of output coupling capacitor. The Y signal is clamped input, while the
C signal is biased input. The power saving circuit provides the output and
chrominance muting function. The IC is available in 8-pin TSSOP.
„ BLOCK DIAGRAM & PIN ASSIGNMENT
MUTE
1
8 VCC
MUTE
Clamp
YIN
2
GND
3
6db
Amp
75Ω
Buff
7
OUT
6
SAG
5
MUTC
Bias
CIN
CHROMINANCE MUTE
4
1
2006/7/5
AA8600AP
Agamem Microelectronics Inc.
___________________________________________________________
PRELIMINARY
Y/C MIX
„ PIN DESCRIPTION
Symbol Pin-No Type
„
Function
MUTE
1
I
Output is muted as this pin is set to high
YIN
2
I
Composite Y input signal is clamped input
GND
3
CIN
4
I
MUTC
5
I
SAG
6
O
OUT
7
O
VCC
8
Ground
Chrominance C input signal is bias input
Only chrominance output signal is muted as this pin is
set to high
SAG correction to reduce the capacitance of output
coupling capacitor
Y/C mix output. As it is less than 0.6V, the protect circuit
is triggered to enable the power saving function
Power supply
ABSOLUTE MAXIMUM RATING
Ta = 25 ℃
Parameter
Supply Voltage
Operating
Ambient
Temperature
Storage
Temperature
Symbol
Rating
MIN TYP
MAX
UNIT
Vcc
-0.3
8
V
Ta
-25
75
℃
Ts
-55
125
℃
CONDITION
NOTE : Stress above those listed under “Absolute Maximum Rating” may cause
permanent damage to the device. This is a stress rating only and functional
operation of the device at these or any other conditions above those indicated
in the operational section of this specification is not implied. Exposure to
absolute maximum rating conditions for the extended periods of time may
affect device reliability.
2
2006/7/5
AA8600AP
Agamem Microelectronics Inc.
___________________________________________________________
PRELIMINARY
Y/C MIX
„ ELECTRICAL CHARACTERISTICS
Ta = 25℃ , Vcc = 5V
Parameter
Symbol
Min
Typ
Max
20
Supply Current
Icc
12.6
Voltage Gain
Gv
-0.3
Frequency
Characteristic
GF
Muting
Attenuation
MT
Muting High Level
VMH
2.2
Vcc
Muting Low Level
VML
GND
0.8
Input Impedance
ZIN
15
Muted Current
SAG-Terminal
Gain
-1.5
-0.5
0.5
-64
Unit
Condition
mA No input Signal
Input Signal Freq =
dB 4.43MHz, 1VP-P,
measure VO1
Input Signal Freq =
dB 7MHz/1MHz, 1VP-P,
measure VO1
Input Signal Freq =
dB 4.43MHz, 1VP-P,
measure VO1
V
V
20
25
KΩ CIN, 50uA
IM
1
2.5
mA MUTE = ‘H’
GSAG
48
Differential Gain
DG
1
2
Differential Phase
DP
1
2.5
„
dB
VIN = 1VP-P, refer
staircase signal
VIN = 1VP-P, refer
deg
staircase signal
%
MUTE MODE
Function
MUTE
MUTC
Output Muting
H
NA
Chrominance Muting
L
H
3
2006/7/5
AA8600AP
Agamem Microelectronics Inc.
___________________________________________________________
PRELIMINARY
Y/C MIX
„ MEASUREMENT CIRCUIT
2.2v
Vcc
1
SW1
2
0.8v
VCC 8 +
47uF
1 MUTE
3
0.1uF
A
1uF +
1 SW2
2.1v
A
2 YIN
2
8
OUT 7
To
+
3 GND
0.1uF
0
SAG 6
Ts
+
2
0.6v
2.2v
P
4 CIN
75Ω
400Ω
SW6
1
SW4
150Ω
22uF
A
0.1uF
VO1
75Ω
SW7
6
0
VO2
100uF
MUTC 5
SW5
0.8v
3
4
2006/7/5
AA8600AP
Agamem Microelectronics Inc.
___________________________________________________________
PRELIMINARY
Y/C MIX
„ MEASUREMENT CONDITIONS
Parameter
Supply Current
Symbol
Icc
SW Condition
2
4
5
6
7
2
1
1
2
O
C No signal input
Voltage Gain
Gv
3
2
2
3
O
C
Frequency
Characteristic
GF
3
1
2
3
O
C
Output Mute
MT
1
1
2
3
O
C
Chrominance Mute
MC
3
2
2
1
O
C
Input Impedance
ZIN
3
1
3
3
O
C
Muted Current
IM
1
1
1
2
O
C
3
2
2
3
O
C
3
2
2
3
C
O
AG Terminal Gain
Measurement Method
1
GSAG
5
Input a 4.43MHz, 1Vp-p
sine wave from CIN and
then measure the output
level from VO1
GV1M : voltage gain at
input frequency=1MHz
GV7M : voltage gain at
input frequency=7MHz
GF=GV7M-GV1M
Input a 4.43MHz, 1Vp-p
sine wave and then
measure the output level
from VO1
Same as output muting
Measure the input voltage
VIS & the open voltage
VIO when a 50uA is
introduced. The ZIN =
|VIS-VIO| / 50uA
Measure the current of
power supply when mute
is set at high
Measure the value of TS
and To at the first as VS1
& VO1 and the value at
second condition as VS2
& VO2, respectively.
GSAG= 20log{(VS2 - VS1)
/ (VO2 - VO1) }
2006/7/5
AA8600AP
Agamem Microelectronics Inc.
___________________________________________________________
PRELIMINARY
Y/C MIX
„ APPLICATION
¾
With SAG
1 MUTE A
A
1uF +
Composite Y
2 YIN
VCC 8 +
47uF
0.1uF
OUT 7 +
100uF
8
6
22uF
0
SAG 6 +
3 GND
0
A
4 CIN P MUTC 5
Chrominance C
75Ω
75Ω
0.1uF
¾
Without SAG
1 MUTE A
A
1uF +
Composite Y
2 YIN
8
VCC 8
+
47uF
OUT 7
6
0
3 GND
Chrominance C
4 CIN
SAG 6
0.1uF
75Ω
+
1000uF
75Ω
0
A
P MUTC 5
0.1uF
6
2006/7/5
AA8600AP
Agamem Microelectronics Inc.
___________________________________________________________
PRELIMINARY
Y/C MIX
„ TSSOP 8L PACKAGE DIMENSION
NOTES:
1. Package body sizes exclude mold flash protrusions or gate burrs
2. Tolerance ± 0.1 ㎜ (4 mil) unless otherwise specified
3. Coplanarity:0.1 ㎜
4. Controlling dimension is millimeter converted inch dimensions are not necessarily exact
5. Followed from jedec mo-153
SYMBOLS
DIMENSIONS IN MILLIMETERS DIMENSIONS IN INCHES
MIN
NOM
MAX
MIN
NOM
MAX
A
---
---
1.20
---
---
0.048
A1
0.05
---
0.15
0.002
---
0.006
A2
0.80
1.00
1.05
0.031
0.039
0.041
b
0.19
---
0.30
0.007
---
0.012
C
0.09
---
0.20
0.004
---
0.008
D
2.90
3.00
3.10
0.114
0.118
0.122
E
6.20
6.40
6.60
0.244
0.252
0.260
E1
4.30
4.40
4.50
0.169
0.173
0.177
e
---
0.65
---
---
0.026
---
L
0.45
0.60
0.75
0.018
0.024
0.030
y
---
---
0.10
---
---
0.004
θ
0°
---
8°
0°
---
8°
7
2006/7/5