AWT6273 HELP3TM Cellular/WCDMA 3.4 V/29 dBm Linear Power Amplifier Module Data Sheet - Rev 2.1 FEATURES • InGaP HBT Technology • High Efficiency: 43 % @ POUT = +29 dBm AWT6273R 20 % @ POUT = +16 dBm 8 % @ POUT = +8 dBm • Low Quiescent Current: 7 mA • Low Leakage Current in Shutdown Mode: <1 µA • Internal Voltage Regulator Eliminates the Need for External Reference Voltage (No VREF Required) • Optimized for a 50 Ω System M20 Package 10 Pin 4 mm x 4 mm x 1 mm Surface Mount Module • Low Profile Miniature Surface Mount Package • RoHS Compliant Package, 250 oC MSL-3 • HSDPA Compliant (no backoff) APPLICATIONS • Dual Band WCDMA Wireless Handsets • Dual Mode 3GPP Wireless Handsets PRODUCT DESCRIPTION The AWT6273 HELP3TM PA is the 3rd generation WCDMA product for UMTS handsets. This PA incorporates ANADIGICS’ HELP3TM technology to provide low power consumption without the need for an external voltage regulator. The device is manufactured on an advanced InGaP HBT MMIC technology offering state-of-the-art reliability, temperature stability, and ruggedness. There are three selectable bias modes that optimize efficiency for different output power levels, and a shutdown mode with low leakage current, increase handset talk and standby time. The self-contained 4 mm x 4 mm x 1 mm surface mount package incorporates matching networks optimized for output power, efficiency, and linearity in a 50 Ω system. GND at slug (pad) VENABLE 1 Bias Control Voltage Regulation 10 GND 9 GND VMODE1 2 VMODE2 3 8 RFOUT RFIN 4 7 GND 5 6 VCC VBATT Figure 1: Block Diagram 05/2008 AWT6273 GND VENABLE 1 10 GND VMODE1 2 9 GND VMODE2 3 8 RFOUT RFIN 4 7 GND VBATT 5 6 VCC GND Figure 2: Pinout (X-ray Top View) Table 1: Pin Description 2 PIN NAME DESCRIPTION 1 VENABLE PA Enable Voltage 2 VMODE1 Mode Control Voltage 1 3 VMODE2 Mode Control Voltage 2 4 RFIN RF Input 5 VBATT Battery Voltage 6 VCC Supply Voltage 7 GND Ground 8 RFOUT RF Output 9 GND Ground 10 GND Ground Data Sheet - Rev 2.1 05/2008 AWT6273 ELECTRICAL CHARACTERISTICS Table 2: Absolute Minimum and Maximum Ratings PARAMETER MIN MAX UNIT Supply Voltage (VCC) 0 +5 V Battery Voltage (VBATT) 0 +6 V Control Voltages (VMODE1, VMODE2, VENABLE) 0 +3.5 V RF Input Power (PIN) - +10 dBm -40 +150 °C Storage Temperature (TSTG) Stresses in excess of the absolute ratings may cause permanent damage. Functional operation is not implied under these conditions. Exposure to absolute ratings for extended periods of time may adversely affect reliability. Table 3: Operating Ranges PARAMETER MIN TYP MAX UNIT COMMENTS Operating Frequency (f) 824 - 849 MHz Supply Voltage (VCC) +3.2 - +3.4 +1.5 +4.2 - V POUT < +29 dBm TBD Enable Voltage (VENABLE) +2.15 0 +2.4 - +3.1 +0.5 V PA "on" PA "shut down" Mode Control Voltage (VMODE1,VMODE2) +2.15 0 +2.4 - +3.1 +0.5 V Low Bias Mode High Bias Mode RF Output Power (POUT) 3GPP HSDPA Case A HSDPA Case B HSDPA Case C +28.5 (1) +27.5 (1) +26.5 (1) +26.0 (1) +29.0 +28.0 +27.0 +26.5 - dBm Case Temperature (TC) -10 - +90 °C 1/15 < c/d < 12/15 13/15 < c/d < 15/8 15/7 < c/d < 15/0 The device may be operated safely over these conditions; however, parametric performance is guaranteed only over the conditions defined in the electrical specifications. Notes: (1) For operation at Vcc = +3.2 V, Pout is derated by 0.5 dB. Data Sheet - Rev 2.1 05/2008 3 AWT6273 Table 4: Electrical Specifications (TC = +25 °C, VCC = +3.4 V, VBATT = +3.4 V, VENABLE = +2.4 V, 50 Ω system) PARAMETER MIN TYP MAX UNIT Gain 25 13 10.5 27.5 15 12.5 30 17.5 15 ACLR1 at 5 MHz offset (1) - -42 -44 -42 ACLR2 at 10 MHz offset - COMMENTS POUT VMODE1 VMODE2 dB +29 dBm +16 dBm +8 dBm 0V 2.4 V 2.4 V 0V 0V 2.4 V -38 -38 -38 dBc +29 dBm +16 dBm +8 dBm 0V 2.4 V 2.4 V 0V 0V 2.4 V -55 -57 -62 -48 -48 -48 dBc +29 dBm +16 dBm +8 dBm 0V 2.4 V 2.4 V 0V 0V 2.4 V 40 17 6 43 20 8 - % +29 dBm +16 dBm +8 dBm 0V 2.4 V 2.4 V 0V 0V 2.4 V Quiescent Current (Icq) - 7 15 11 21 mA VMODE1 = +2.4 V, VMODE2 = +2.4 V VMODE1 = +2.4 V, VMODE2 = 0 V Mode Control Current - 0.3 0.8 mA through VMODE pins, VMODE = +2.4 V Enable Current - 0.5 1 mA through VENABLE pin BATT Current - 2.5 5 mA through VBATT pin, VMODE1 = +2.4 V, VMODE2 = +2.4 V or 0 V Leakage Current - <1 5 µA VBATT = +4.2 V, VCC = +4.2 V, VENABLE = 0 V, VMODE1 = 0 V, VMODE2 = 0 V Noise in Receive Band (2) - -136 -134 dBm/Hz Harmonics 2fo 3fo, 4fo - -43 -50 -35 -35 dBc Input Impedance - - 2:1 VSWR Spurious Output Level (all spurious outputs) - - -70 dBc 8:1 - - VSWR Power-Added Efficiency (1) Load mismatch stress with no permanent degradation or failure POUT = +29 dBm, VMODE1 = 0 V, VMODE2 = 0 V POUT < +29 dBm See Note 3 Applies over full operating range Notes: (1) ACLR and Efficiency measured at 836.5 MHz. (2) 869 MHz to 894 MHz. (3) POUT +29 dBm, In-band load VSWR < 5:1, Out-of-band load VSWR < 10:1. Applies over all operating conditions. 4 Data Sheet - Rev 2.1 05/2008 AWT6273 APPLICATION INFORMATION To ensure proper performance, refer to all related Application Notes on the ANADIGICS web site: http://www.anadigics.com Shutdown Mode The power amplifier may be placed in a shutdown mode by applying logic low levels (see Operating Ranges table) to the VENABLE, VMODE1 and VMODE2 voltages. Bias Modes The power amplifier may be placed in either a Low Bias mode or a High Bias mode by applying the appropriate logic level (see Operating Ranges table) to the VMODE voltages. The Bias Control table lists the recommended modes of operation for various applications. Three operating modes are recommended to optimize current consumption. High Bias/High Power operating mode is for POUT levels > 16 dBm. At ~16dBm - 7 dBm, the PA should be “Mode Switched” to Medium Bias Mode. For POUT levels < ~8 dBm, the PA can be switched to Low Bias/Low Power Mode used for this POUT range for even lower quiescent current consumption. Table 5: Bias Control APPLICATION POUT LEVELS BIAS MODE VENABLE VMODE1 VMODE2 VCC VBATT WCDMA - low power (Low Bias Mode) < +8 dBm Low +2.4 V +2.4 V +2.4 V 3.2 - 4.2 V > 3.2 V WCDMA - med power (Medium Bias Mode) < +16 dBm Med +2.4 V +2.4 V 0V 3.2 - 4.2 V > 3.2 V WCDMA - high power (High Bias Mode) > +16 dBm High +2.4 V 0V 0V 3.2 - 4.2 V > 3.2 V Optional lower VCC in low power mode < +7 dBm Low +2.4 V +2.4 V 2.4 V > 1.5 V > 3.2 V - Shutdown 0V 0V 0V 3.2 - 4.2 V > 3.2 V Shutdown 1 VENABLE C2 0.01 µF VMODE1 2 3 VMODE2 10K Optional pull-down RF IN 4 5 VENABLE GND VMODE1 GND VMODE2 RFOUT RFIN GND VBATT VCC 10 9 8 RF OUT 7 6 GND at slug VBATT VCC C5 2.2 µF C1 0.01µF C3 0.01µF C4 2.2µF ceramic Figure 3: Application Circuit Schematic Data Sheet - Rev 2.1 05/2008 5 AWT6273 PACKAGE OUTLINE Figure 4: M20 Package Outline - 10 Pin 4 mm x 4 mm x 1 mm Surface Mount Module 73R 73R Figure 5: Branding Specification - M20 Package 6 Data Sheet - Rev 2.1 05/2008 AWT6273 COMPONENT PACKAGING Figure 6: Tape & Reel Packaging Table 6: Tape & Reel Dimensions PACKAGE TYPE TAPE WIDTH POCKET PITCH REEL CAPACITY MAX REEL DIA 4 mm x 4 mm x 1 mm 12 mm 8 mm 2500 13" Data Sheet - Rev 2.1 05/2008 7 AWT6273 ORDERING INFORMATION ORDER NUMBER TEMPERATURE RANGE PACKAGE DESCRIPTION AWT6273RM20P8 -10 oC to +90 oC RoHS Compliant 10 Pin 4 mm x 4 mm x 1 mm Tape and Reel, 2500 pieces per Reel Surface Mount Module AWT6273RM20P9 -10 oC to +90 oC RoHS Compliant 10 Pin 4 mm x 4 mm x 1 mm Partial Tape and Reel Surface Mount Module COMPONENT PACKAGING ANADIGICS, Inc. 141 Mount Bethel Road Warren, New Jersey 07059, U.S.A. Tel: +1 (908) 668-5000 Fax: +1 (908) 668-5132 URL: http://www.anadigics.com E-mail: [email protected] IMPORTANT NOTICE ANADIGICS, Inc. reserves the right to make changes to its products or to discontinue any product at any time without notice. The product specifications contained in Advanced Product Information sheets and Preliminary Data Sheets are subject to change prior to a product’s formal introduction. Information in Data Sheets have been carefully checked and are assumed to be reliable; however, ANADIGICS assumes no responsibilities for inaccuracies. ANADIGICS strongly urges customers to verify that the information they are using is current before placing orders. warning ANADIGICS products are not intended for use in life support appliances, devices or systems. Use of an ANADIGICS product in any such application without written consent is prohibited. 8 Data Sheet - Rev 2.1 05/2008