HELP4 TM ALT6720 E800 (Band 20) LTE Linear PAM Data Sheet - Rev 2.3 FEATURES • LTE Compliant • 4th Generation HELPTM technology • High Efficiency (LTE MPR = 0 dB): • 36 % @ POUT = +27.5 dBm • 23 % @ POUT = +16 dBm • 16 % @ POUT = +7 dBm ALT6720 • Low Quiescent Current: 3 mA • Low Leakage Current in Shutdown Mode: <5 µA • Internal Voltage Regulator • Integrated “daisy chainable” directional coupler with CPLIN and CPLOUT port. M45 Package 10 Pin 3 mm x 3 mm x 1 mm Surface Mount Module • Internal DC block on IN/OUT RF ports • Optimized for a 50 Ω System • 1.8 V Control Logic • RoHS Compliant Package, 260 oC MSL-3 APPLICATIONS • Band 20 LTE Wireless Devices PRODUCT DESCRIPTION GND at Slug (pad) The ALT6720 HELP4TM PA is a 4th generation HELPTM product for LTE devices operating in E800 MHz Band 20. This PA incorporates ANADIGICS’ HELP4 TM technology to deliver exceptional efficiency at low power levels and low quiescent current without the need for external voltage regulators or converters. The device is manufactured using advanced InGaPPlus TM HBT technology offering state-of-the-art reliability, temperature stability, and ruggedness. Three selectable bias modes that optimize efficiency for different output power levels and a shutdown mode with low leakage current increase handset talk and standby time. A “daisy chainable” directional coupler is integrated in the module, thus eliminating the need of an external coupler. The self-contained 3 mm x 3 mm x 1 mm surface mount package incorporates matching networks optimized for output power, efficiency, and linearity in a 50 Ω system. VBATT 1 RFIN 2 VMODE2 3 VMODE1 VEN 03/2012 10 VCC 9 RFOUT 8 CPLIN 4 7 GND 5 6 CPLOUT CPL Bias Control Voltage Regulation Figure 1: Block Diagram ALT6720 VBATT 1 10 RFIN 2 9 RFOUT VMODE2 3 8 CPLIN VMODE1 4 7 GND VEN 5 6 CPLOUT Figure 2: Pinout (X-ray Top View) Table 1: Pin Description 2 PIN NAME DESCRIPTION 1 VBATT Battery Voltage 2 RFIN RF Input 3 VMODE2 Mode Control Voltage 2 4 VMODE1 Mode Control Voltage 1 5 VEN 6 CPLOUT 7 GND Ground 8 CPLIN Coupler Input 9 RFOUT RF Output 10 VCC PA Enable Voltage Coupler Output Supply Voltage Data Sheet - Rev 2.3 03/2012 VCC ALT6720 ELECTRICAL CHARACTERISTICS Table 2: Absolute Minimum and Maximum Ratings PARAMETER MIN MAX UNIT Supply Voltage (VCC) 0 +5.0 V Battery Voltage (VBATT) 0 +6 V Control Voltages (VMODE1, VMODE2, VEN) 0 +3.5 V RF Input Power (PIN) - +10 dBm -40 +150 °C Storage Temperature (TSTG) Stresses in excess of the absolute ratings may cause permanent damage. Functional operation is not implied under these conditions. Exposure to absolute ratings for extended periods of time may adversely affect reliability. Table 3: Operating Ranges PARAMETER MIN TYP MAX UNIT COMMENTS Operating Frequency (f) 832 - 862 MHz Supply Voltage (VCC) +3.1 +3.4 +4.35 V POUT ≤ +27.5 dBm Enable Voltage (VEN) +1.35 0 +1.8 - +3.1 +0.5 V PA "on" PA "shut down" Mode Control Voltage (VMODE1,VMODE2) +1.35 0 +1.8 - +3.1 +0.5 V Low Bias Mode High Bias Mode LTE/UMTS Output Power (1, 2, 3) LTE (MPR=0), HPM LTE (MPR=0), MPM LTE (MPR=0), LPM 26.7 - 27.5 16.0 7.0 - dBm TS 36.101 Rel 8 Case Temperature (TC) -40 - +90 °C The device may be operated safely over these conditions; however, parametric performance is guaranteed only over the conditions defined in the electrical specifications. Notes: (1) LTE waveform characteristics up to 20 MHz QPSK, 18 RB’s. (2) For 3.1 V operation POUT derated 0.8 dB. (3) For operation at +105 °C, POUT is derated by 1.0 dB. 3 Data Sheet - Rev 2.3 03/2012 ALT6720 Table 4: Electrical Specifications - LTE Operation (MPR = 0 waveform, 10 MHZ QPSK, 12 RB’s) (TC = +25 °C, VCC = +3.4 V, VBATT = +3.4 V, VEN = +1.8 V, 50 Ω system) PARAMETER MIN TYP MAX UNIT Gain 27.5 17 10 30 20 13 33.5 23 16 LTE to LTE, E-UTRA - -39 -39 -40 UTRA ACLR1 - UTRA ACLR2 POUT VMODE1 VMODE2 dB +27.5 dBm +16 dBm +7 dBm 0V 1.8 V 1.8 V 0V 0V 1.8 V -35 -35 -35 dBc +27.5 dBm +16 dBm +7 dBm 0V 1.8 V 1.8 V 0V 0V 1.8 V -40 -39 -41 -36 -36 -36 dBc +27.5 dBm +16 dBm +7 dBm 0V 1.8 V 1.8 V 0V 0V 1.8 V - -60 -60 -60 -40 -40 -40 dBc +27.5 dBm +16 dBm +7 dBm 0V 1.8 V 1.8 V 0V 0V 1.8 V 32 19 13 36 23 16 - % +27.5 dBm +16 dBm +7 dBm 0V 1.8 V 1.8 V 0V 0 V 1.8 V Quiescent Current (Icq) Low Bias Mode - 2.5 4 mA through VCC pin 1.8 V 1.8 V Mode Control Current - 0.07 0.15 mA through VMODE pins, VMODE1,2 = +1.8 V Enable Current - 0.03 0.1 mA through VEN pin BATT Current - 0.8 1.5 mA through VBATT pin, VMODE1,2 = +1.8 V Leakage Current - <5 10 µA VBATT = +4.35 V, VCC = +4.35 V, VEN = 0 V, VMODE1,2 = 0 V Noise Power - -132 -138 -143 - Harmonics 2fo 3fo, 4fo - -50 -62 - dBc Coupling Factor - 20.5 - dB Directivity - 20 - dB Daisy Chain Insertion Loss - <0.3 - dB 698 - 2620 MHz Pin 8 through 9, shutdown mode Spurious Output Level (all spurious outputs) - - -70 dBc P OUT < +27.5 dBm In-band load VSWR < 5:1 Out-of-band load VSWR < 10:1 Applies over all operating conditions 8:1 - - VSWR Power-Added Efficiency (1) Load mismatch stress with no permanent degradation or failure 791 - 821 MHz dBm/Hz GPS Band, 1574 - 1577 MHz ISM Band, 2400 - 2483.5 MHz Notes: (1) ACLR and Efficiency measured at 847 MHz. 4 COMMENTS Data Sheet - Rev 2.3 03/2012 POUT < +27.5 dBm Applies over full operating range ALT6720 APPLICATION INFORMATION To ensure proper performance, refer to all related Application Notes on the ANADIGICS web site: http://www.anadigics.com to the VMODE pins. The Bias Control table below lists the recommended modes of operation for various applications. Shutdown Mode The power amplifier may be placed in a shutdown mode by applying logic low levels (see Operating Ranges table) to the VEN, VMODE1 and VMODE2 voltages. Three operating modes are recommended to optimize current consumption. High Bias/High Power operating mode is for POUT levels > 16 dBm. At ~16 dBm - 7 dBm, the PA could be switched to Medium Power Mode. For POUT levels < ~7 dBm, the PA could be switched to Low Power Mode for extremely low current consumption. Bias Modes The power amplifier may be placed in either Low, Medium or High Bias modes by applying the appropriate logic level (see Operating Ranges table) Table 5: Bias Control APPLICATION POUT LEVELS BIAS MODE VEN VMODE1 VMODE2 VCC VBATT Low power (Low Bias Mode) ≤ +7 dBm Low +1.8 V +1.8 V +1.8 V 3.2 - 4.35 V > 3.2 V Med power (Medium Bias Mode) ≥ +7 dBm ≤ +16 dBm Low +1.8 V +1.8 V 0V 3.2 - 4.35 V > 3.2 V High power (High Bias Mode) ≥ +16 dBm High +1.8 V 0V 0V 3.2 - 4.35 V > 3.2 V - Shutdown 0V 0V 0V 3.2 - 4.35 V > 3.2 V Shutdown VBATT C6 2.2 µF C1 0.01µF C5 100 pF GND at slug 1 VMODE2 VMODE1 VEN (1) VCC RFIN RFOUT 3 VMODE2 CPLIN 4 VMODE1 GND 7 5 VEN 9 8 CPLOUT 6 Notes: (1) Rise and Fall time on VEN Control Signal must be ≤ 1.0 µS. Figure 3: Evaluation Board Schematic 5 Data Sheet - Rev 2.3 03/2012 C2 0.01 µF VCC C4 2.2 µF ceramic 10 VBATT 2 RFIN C3 330 pF RFOUT CPLIN CPLOUT ALT6720 PACKAGE OUTLINE Figure 4: M45 Package Outline - 10 Pin 3 mm x 3 mm x 1 mm Surface Mount Module Pin 1 Identifier Date Code YY=Year; WW=Work week 6720R Part Number LLLLNN YYWWCC Lot Number Country Code (CC) Figure 5: Branding Specification - M45 Package 6 Data Sheet - Rev 2.3 03/2012 ALT6720 PCB AND STENCIL DESIGN GUIDELINE Figure 6: Recommended PCB Layout Information 7 Data Sheet - Rev 2.3 03/2012 ALT6720 COMPONENT PACKAGING Pin 1 Figure 7: Carrier Tape Table 8: Reel 8 Data Sheet - Rev 2.3 03/2012 ALT6720 ORDERING INFORMATION ORDER NUMBER TEMPERATURE RANGE PACKAGE DESCRIPTION ALT6720RM45Q7 -40 oC to +90 oC RoHS Compliant 10 Pin 3 mm x 3 mm x 1 mm Tape and Reel, 2500 pieces per Reel Surface Mount Module ALT6720RM45P9 -40 oC to +90 oC RoHS Compliant 10 Pin 3 mm x 3 mm x 1 mm Partial Tape and Reel Surface Mount Module COMPONENT PACKAGING ANADIGICS, Inc. 141 Mount Bethel Road Warren, New Jersey 07059, U.S.A. Tel: +1 (908) 668-5000 Fax: +1 (908) 668-5132 URL: http://www.anadigics.com IMPORTANT NOTICE ANADIGICS, Inc. reserves the right to make changes to its products or to discontinue any product at any time without notice. The product specifications contained in Advanced Product Information sheets and Preliminary Data Sheets are subject to change prior to a product’s formal introduction. Information in Data Sheets have been carefully checked and are assumed to be reliable; however, ANADIGICS assumes no responsibilities for inaccuracies. ANADIGICS strongly urges customers to verify that the information they are using is current before placing orders. warning ANADIGICS products are not intended for use in life support appliances, devices or systems. Use of an ANADIGICS product in any such application without written consent is prohibited. 9 Data Sheet - Rev 2.3 03/2012