AZ765 SPST SUBMINIATURE POWER RELAY FEATURES • • • • • Small footprint Low cost Epoxy sealed version available 10 Amp switching UL, CUR file E44211 CONTACTS GENERAL DATA Arrangement SPST (1 Form A) Ratings Resistive load: Max. switched power: 150 W or 1250 VA Max. switched current: 10 A Max. switched voltage: 30* VDC or 250 VAC *Note: If switching voltage is greater than 30 VDC, special precautions must be taken. Please contact the factory. Rated Load UL, CUR Life Expectancy Mechanical Electrical Minimum operations 1 x 107 1 x 105 at 10 A 120 VAC Res. Operate Time (typical) 8 ms at nominal coil voltage Release Time (typical) 5 ms at nominal coil voltage (with no coil suppression) Dielectric Strength 2500 Vrms coil to contact (at sea level for 1 min.) 1000 Vrms between open contacts 10 A at 125 VAC, 5A at 250 VAC 5 A at 30 VDC Insulation Resistance 1000 megohms min. at 20°C 500 VDC 50% RH Material Silver cadmium oxide Dropout Greater than 5% of nominal coil voltage Resistance < 50 milliohms initially (24 V, 1 A voltage drop method) Ambient Temperature Operating Storage At nominal coil voltage -40°C (-40°F) to 65°C (149°F) -40°C (-40°F) to 105°C (221°F) Vibration 0.040" DA at 10–50 Hz Shock 10 g operating, 100 g damage Enclosure P.B.T. polyester Terminals Tinned copper alloy, P. C. Max. Solder Temp. 270°C (518°F) Max. Solder Time 5 seconds Max. Solvent Temp. 80°C (176°F) Max. Immersion Time 30 seconds Weight 6 grams COIL Power At Pickup Voltage (typical) 253 mW Max. Continuous Dissipation 1.1 W at 20°C (68°F) ambient Temperature Rise 42°C (76°F) at nominal coil voltage Temperature Max. 105°C (221°F) NOTES 1. All values at 20°C (68°F). 2. Relay may pull in with less than “Must Operate” value. 3. Specifications subject to change without notice. 12/11/08W AZ765 RELAY ORDERING DATA COIL SPECIFICATIONS Nominal Coil VDC 3 Must Operate VDC 2.25 ORDER NUMBER* Max. Continuous VDC 4.7 Coil Resistance ± 10% 20 1 Form A AZ765–1A–3D 5 3.75 7.7 55 AZ765–1A–5D 6 4.5 9.4 80 AZ765–1A–6D AZ765–1A–9D 9 6.75 14.0 180 12 9.0 18.7 320 AZ765–1A–12D 18 13.5 28.1 720 AZ765–1A–18D 24 48 18.0 36.0 37.5 62.4 1,280 5,120 AZ765–1A–24D AZ765–1A–48D *Add suffix “E” for epoxy sealed version. MECHANICAL DATA PC BOARD LAYOUT .402 [10.2] .717 [18.2] .058 [1.48] .500 [12.7] .100 [2.54] .300 [7.6] .585 [14.85] 4 x ø.051 [ø1.3] FORM A .150 [3.8] 2 x .018 SQR. [0.45] .012 TYP. [0.3] VIEWED TOWARD TERMINALS WIRING DIAGRAM 5 4 .039 TYP. [1.0] 1 FORM A 3 VIEWED TOWARD TERMINALS Dimensions in inches with metric equivalents in parentheses. Tolerance: ± .010" 12/11/08W