AZ767 SPDT SUBMINIATURE POWER RELAY FEATURES • • • • • • Small footprint Low cost Class B insulation standard Epoxy sealed version available 10 Amp switching UL, CUR file E44211 CONTACTS Arrangement SPST (1 Form A) SPDT (1 Form C) Ratings Resistive load: Rated Load UL, CUR Material Resistance GENERAL DATA Life Expectancy Mechanical Electrical Minimum operations 1 x 107 1 x 105 at 5 A 240 VAC Res. Operate Time (typical) 8 ms at nominal coil voltage Release Time (typical) 5 ms at nominal coil voltage (with no coil suppression) Dielectric Strength 2500 Vrms coil to contact (at sea level for 1 min.) 1000 Vrms between open contacts Max. switched power: 150 W (SPST-NO) standard 1250 VA (SPST-NO) standard 90 W (SPST-NO) sensitive 750 VA (SPST-NO) sensitive 90 W (SPDT) 750 W (SPDT) Max. switched current: 10 A AC SPST-NO standard 5 A DC SPST-NO standard 3 A AC/DC SPST-NO sensitive 3 A AC/DC SPDT Max. switched voltage: 150* VDC or 380 VAC Insulation Resistance 1000 megohms min. at 20°C 500 VDC 50% RH Dropout Greater than 5% of nominal coil voltage Ambient Temperature Operating At nominal coil voltage -40°C (-40°F) to 90°C (194°F), standard -40°C (-40°F) to 105°C (221°F), sensitive -40°C (-40°F) to 130°C (266°F) Vibration 0.062" DA at 10–50 Hz *Note: If switching voltage is greater than 30 VDC, special precautions must be taken. Please contact the factory. Shock 10 g operating, 100 g damage Enclosure P.B.T. polyester Terminals Tinned copper alloy, P. C. Max. Solder Temp. 270°C (518°F) Max. Solder Time 5 seconds Max. Solvent Temp. 80°C (176°F) Max. Immersion Time 30 seconds Weight 6 grams Form A 10 A at 125 VAC, Res., 30k cycles [1] 10 A at 125 VAC, General Use., 100k cycles [2] 5 A at 250 VAC, General Use, 100k [1][2] 5 A at 30 VDC, Res., 100k cycles [1][2] 300 W at 120 VAC Tungsten [2] 3 A at 250 VAC, General Use, 100k cycles [1][2] sensitive 3 A at 30 VDC, Res., 100k cycles [1][2] - sensitive 5 A at 125 VAC, Res., 100k cycles [1] - sensitive 10 LRA / 1.5 FLA at 120 VAC, 100k cycles [1] 1/10 HP at 125 VAC, 100k cycles [1] 1/16 HP at 250 VAC, 100k cycles [1] 8 A at 250 VAC, General Use, 100k cycles [2] - sensitive high capacity Form C 3 A at 250 VAC, General Use, 100k cycles [1][2] 3 A at 30 VDC, Res., 100k cycles [1][2] [1] silver cadmium oxide [2] silver nickel Silver cadmium oxide or silver nickel <100 milliohms initially (24 V, 1 A voltage drop method) Storage COIL Power At Pickup Voltage (typical) 253 mW standard 113 mW sensitive Max. Continuous Dissipation 1.25 W at 20°C (68°F) ambient Temperature Rise 41°C (74°F) at nominal coil voltage, standard 22°C (40°F) at nominal coil voltage, sensitive Temperature Max. 130°C (266°F) NOTES 1. All values at 20°C (68°F). 2. Relay may pull in with less than “Must Operate” value. 3. Specifications subject to change without notice. 9/6/06 W AZ767 RELAY ORDERING DATA STANDARD RELAYS COIL SPECIFICATIONS Nominal Coil VDC 3 Must Operate VDC 2.25 Max. Continuous VDC 5.0 ORDER NUMBER* Coil Resistance ± 10% 20 Form A (SPST) Form C (SPDT) AZ767–1A–3D AZ767–1C–3D 5 3.75 8.3 55 AZ767–1A–5D AZ767–1C–5D 6 4.5 10.0 80 AZ767–1A–6D AZ767–1C–6D 9 6.75 15.0 180 AZ767–1A–9D AZ767–1C–9D 12 9.0 20.0 320 AZ767–1A–12D AZ767–1C–12D 18 13.5 30.0 720 AZ767–1A–18D AZ767–1C–18D 24 18.0 40.0 1,280 AZ767–1A–24D AZ767–1C–24D 48 36.0 80.0 5,120 AZ767-1A-48D AZ767-1C-48D *For silver nickel contacts change “-1A” to “-1AB” or “-1C” to “-1CB”. Add suffix “E” for epoxy sealed version. Add suffix “A” for gold plated version. SENSITIVE RELAYS COIL SPECIFICATIONS Nominal Coil VDC 3 Must Operate VDC 2.25 Max. Continuous VDC 7.5 ORDER NUMBER* Coil Resistance ± 10% 45 Form A (SPST) AZ767–1A–3DS 5 3.75 12.5 125 AZ767–1A–5DS 6 4.5 15.0 180 AZ767–1A–6DS 9 6.75 22.4 400 AZ767–1A–9DS 12 9.0 30.0 720 AZ767–1A–12DS 18 13.5 44.7 1600 AZ767–1A–18DS 24 18.0 59.2 2800 AZ767–1A–24DS *For silver nickel contacts change “-1A” to “-1AB”. For high capacity silver nickel contacts change “-1A” to “-1ABT”. Add suffix “E” for epoxy sealed version. Add suffix “A” for gold plated version. MECHANICAL DATA PC BOARD LAYOUT .059 [1.50] .073 [1.85] .417 MAX. [10.59] .740 MAX. [18.80] .100 [2.54] .058 [1.49] .300 [7.62] 5xø.052 - FORM C 4xø.052 - FORM A [ø1.3] .441 [11.20] FORM C ONLY VIEWED TOWARD TERMINALS WIRING DIAGRAM .614 MAX. [15.59] .147 [3.73] 5 1 .073 [1.85] 4 2 3 FORM C ONLY VIEWED TOWARD TERMINALS Dimensions in inches with metric equivalents in parentheses. Tolerance: ± .010" 9/6/06 W