TI TPS62111

Power for C5504/05
SLVA401A
C5504/05 Power Spec Table
Pin Name
LDOI 3
Voltage (V)
Max Current 4
(mA)
1.8 - 3.6
5
Tolerance
Sequencing
Order
Comments
Supplying ANA LDO (supplies
VDDA_ANA and VDDA_PLL).
Typical Core Power Consumption:
Core
CVDD1, CVDDRTC1
1.05 / 1.30
500
-5%, +10%
1.3V
70
-5%, +10%
DVDDIO, DVDDRTC
1.8 / 2.5 / 2.8 /
3.3
300
-10%,
+10%
DVDDEMIF
1.8 / 2.5 / 2.8 /
3.3
245
-10%,
+10%
3.3V
55
-5%, +5%
USB_VDD1P3, USB_VD
DA1P3
USB_VDDOSC,
USB_VDDA3P3,
USB_VDDPLL
- 0.22mW/MHz for 75% DMAC + 25% NOP (CVDD
=1.3V @ 100MHz, Room Temp)
- 0.14mW/MHz for 75% DMAC + 25% NOP (CVDD
=1.05V @ 100MHz, Room Temp)
12
For best performance, these voltages
should be powered by a LDO in order to
minimize noise.
NOTES:
1) CVDD & CVDDRTC can be 1.05Vor 1.30V for ≤60MHz operation and 1.30V for operating higher than 60MHz
2) Power Supply Sequencing: No sequencing is required (for further details, see section 5.3.1 of the data sheet)
3) If GPAIN pins are used as general purpose outputs, the internal ANA_LDO must not be used as the max current capability of ANA_LDO
can be exceeded. In this case use an external regulator to supply VDDA_ANA..
4) This column shows the maximum design current of each power domain. See the C5505/04 data sheet for actual current consumptions of
some usage cases. See the data in the “Comments” column above.
SLVA401A
Power Options for C5504/05
*Please visit ti.com/processorpower for COMPLETE power solutions
Highest Efficiency,
Low Cost
Integrated PMIC
High-Efficiency,
Dual DCDC + PMIC
VIN: 3.6V – 6V
TPS65054
TPS65054
VIN: 3.6V – 5V
Multi-output
Multi-output
DCDC
DCDC1
DCDC
Converter
Converter DCDC2
Vbat
LDO1
VINDCDC1/2
VIN_LDOx
LDO2
EN_LDOx
LDO3
LDO4
Lowest Cost,
Dual DCDC @ 3.3V & 1.3V
VIN: 12V
TPS62400
TPS62400
Dual
Dual
600mA/400mA
600mA/400mA
DCDC
DCDCConverter
Converter
DCDC1
EN1
EN2
DCDC2
TPS62410
TPS62410
VIN: 3.6V – 6V
Dual
Dual
600mA/400mA
600mA/400mA
DCDC
Converter
DCDC Converter
TPS65001
TPS65001
Triple
Triple
DCDC
DCDCConverter
Converter
With
WithSVS
SVS
EN2
EN1
DCDC1
DCDC2
• 2 DCDC + 4 LDO’s in 4x4mm QFN
• 2.25MHz for Small Inductors
• 180˚ Out-of-Phase Operation
SLVA401A
TPS62400
TPS62400
Dual
Dual
600mA/400mA
600mA/400mA
DCDC
DCDCConverter
Converter
EN2
EN1
DCDC1
DCDC2
LDO1
LDO2
• 3.6 – 6V input voltage
• Up to 95% Efficiency
• Efficiency up to 95%
• 2.25MHz for Small Inductors
• 2.25MHz for Small Inductors
• Integrated SVS
EN
Dual
Dual250mA
250mALDO
LDO
LDO1
LDO2
TPS62111
TPS62111
1.5
1.5
DCDC
DCDCConverter
Converter
TPS71202
TPS71202
DCDC1
EN
High Input Voltage,
DCDC Converters
• Input voltage capable up to 17V
• PFM mode for high efficiency
during light loads
• Low-Noise LDO (32uVrms)
Highest Efficiency, Single PMIC
(TPS65054)
Vin: 3.6V – 5.5V
TPS65054
C5514/15
1.8 / 2.5 / 2.8 / 3.3V
@ 300mA
1.05V / 1.3V @ 500mA
1.8 - 3.3V @ 5mA
1.8 / 2.5 / 2.8 / 3.3V
@ 245mA
DVDDIO, DVDDRTC
CVDD, CVDDRTC
LDOI
DVDDEMIF
OPEN
1.3V @ 70mA
3.3V @ 55mA
SLVA401A
USB_VDD1P3, USB_VDDA1P3,
USB_VDDOSC, USB_VDDA3P3,
USB_VDDPLL
High Efficiency, Low part count
(TPS62400 + TPS65001)
Vin: 3.6V – 5.5V
C5504/05
TPS62400
400mA
600mA
1.8 / 2.5 / 2.8 / 3.3V
@ 300mA
1.05V / 1.3V @ 500mA
DVDDIO, DVDDRTC
CVDD, CVDDRTC
TPS65001
600mA
1.8 / 2.5 / 2.8 / 3.3V
@ 245mA
DVDDEMIF
/PG
200mA
200mA
3.3V @ 55mA
1.8 - 3.3V @ 5mA
1.3V @ 70mA
SLVA401A
USB_VDDOSC, USB_VDDA3P3,
USB_VDDPLL
LDOI
USB_VDD1P3, USB_VDDA1P3,
High Efficiency, Lowest cost
Reduce rails to 1.3V and 3.3V
TPS62410
DVDDIO, DVDDRTC
Vin: 3.6V – 5.5V
800mA
C5504/05
3.3V @ 605mA
DVDDEMIF
LDOI
USB_VDDOSC, USB_VDDA3P3,
USB_VDDPLL
800mA
1.3V @ 500mA
1.3V @ 70mA
SLVA401A
CVDD, CVDDRTC
USB_VDD1P3, USB_VDDA1P3,
High Input Voltage
C5504/05
TPS62111
3.3V @ 55mA
TPS62400
400mA
1.8 - 3.0V @ 5mA
1.8 / 2.5 / 2.8V
@ 300mA
1.05V / 1.3V @ 500mA
USB_VDDOSC, USB_VDDA3P3,
USB_VDDPLL
LDOI
DVDDIO, DVDDRTC
CVDD, CVDDRTC
600mA
TPS71202
1.8 / 2.5 / 2.8V
@ 245mA
1.3V @ 70mA
SLVA401A
Note: If DVDDIO, DVDDRTC, DVDDEMIF, LDOI are 3.3V, connect directly to 3.3V
DVDDEMIF
USB_VDD1P3, USB_VDDA1P3,
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Amplifiers
amplifier.ti.com
Audio
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DLP® Products
www.dlp.com
Communications and
Telecom
www.ti.com/communications
DSP
dsp.ti.com
Computers and
Peripherals
www.ti.com/computers
Clocks and Timers
www.ti.com/clocks
Consumer Electronics
www.ti.com/consumer-apps
Interface
interface.ti.com
Energy
www.ti.com/energy
Logic
logic.ti.com
Industrial
www.ti.com/industrial
Power Mgmt
power.ti.com
Medical
www.ti.com/medical
Microcontrollers
microcontroller.ti.com
Security
www.ti.com/security
RFID
www.ti-rfid.com
Space, Avionics &
Defense
www.ti.com/space-avionics-defense
RF/IF and ZigBee® Solutions www.ti.com/lprf
Video and Imaging
www.ti.com/video
Wireless
www.ti.com/wireless-apps
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2010, Texas Instruments Incorporated