application INFO available UCC15701/2 UCC25701/2 UCC35701/2 Advanced Voltage Mode Pulse Width Modulator FEATURES DESCRIPTION 700kHz Operation The UCC35701/UCC35702 family of pulse width modulators is intended for isolated switching power supplies using primary side control. They can be used for both off-line applications and DC/DC converter designs such as in a distributed power system architecture or as a telecom power source. Integrated Oscillator/ Voltage Feed Forward Compensation Accurate Duty Cycle Limit The devices feature low startup current, allowing for efficient off-line starting, yet have sufficient output drive to switch power MOSFETs in excess of 500kHz. Accurate Volt-second Clamp Optocoupler Interface Fault Counting Shutdown Fault Latch off or Automatic Shutdown Soft Stop Optimized for Synchronous Rectification 1A Peak Gate Drive Output 130mA Start-up Current Voltage feed forward compensation is operational over a 5:1 input range and provides fast and accurate response to input voltage changes over a 4:1 range. An accurate volt-second clamp and maximum duty cycle limit are also featured. Fault protection is provided by pulse by pulse current limiting as well as the ability to latch off after a programmable number of repetitive faults has occurred. Two UVLO options are offered. UCC35701 family has turn-on and turn-off thresholds of 13V/9V and UCC35702 family has thresholds of 9.6V/8.8V. 750mA Operating Current The UCC35701/2 and the UCC25701/2 are offered in the 14 pin SOIC (D), 14 pin PDIP (N) or in 14 pin TSSOP (PW) packages. The UCC15701/2 is offered in the 14 pin CDIP (J) package. TYPICAL APPLICATION DIAGRAM VIN S UP P LY R1 R2 6 R3 VREF R6 VFF 7 RT 10 CT VDD UCC35701 CT C6 VOUT C4 C1 R4 R5 9 VS CLAMP 11 S YNC 14 SS CS OUT 4 ILIM 2 R8 R10 C2 CF RF R7 3 1 COUNT 12 VREF RCS C3 P GND 5 R8 VIN RETURN RGND 8 FB GND 13 R11 C5 R12 VOUT R13 C6 R14 C7 R15 UDG-98005-1 SLUS293C - JANUARY 2000 - REVISED JUNE 2005 UCC15701/2 UCC25701/2 UCC35701/2 ORDERING INFORMATION ABSOLUTE MAXIMUM RATINGS Supply voltage (Supply current limited to 20mA) . . . . . . . . 15V Supply Current. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20mA Input pins ( ILIM,VFF,RT,CT,VSCLAMP,SYNC,SS, FB) . . . 6V Output Current (OUT) DC. . . . . . . . . . . . . . . . . . . . . +/–180mA Output Current (OUT) Pulse (0.5ms) . . . . . . . . . . . . . . +/–1.2A Storage Temperature. . . . . . . . . . . . . . . . . . . –65°C to +150°C Junction Temperature . . . . . . . . . . . . . . . . . . . –55°C to +150°C Lead Temperature (Soldering, 10 sec.) . . . . . . . . . . . . +300°C UVLO Option 13V / 9V –55°C to +125°C 9.6V / 8.8V Note: All voltages are with respect to GND. Currents are positive into the specified terminal. Consult Packaging Section of the Databook for thermal limitations and considerations of packages. 9.6V / 8.8V TA = TJ 13V / 9V –40°C to +85°C 13V / 9V 0°C to +70°C CONNECTION DIAGRAMS 9.6V / 8.8V DIL-14, SOIC-14, TSSOP-14 (TOP VIEW) N or J, D, PW PACKAGE COUNT 1 14 SS ILIM 2 13 GND VDD 3 12 VREF OUT 4 11 S YNC P GND 5 10 CT VFF 6 9 VS CLAMP RT 7 8 FB Package Part Number CDIP-14 CDIP-14 SOIC-14 PDIP-14 TSSOP-14 SOIC-14 PDIP-14 TSSOP-14 SOIC-14 PDIP-14 TSSOP-14 SOIC-14 PDIP-14 TSSOP-14 UCC15701J UCC15702J UCC25701D UCC25701N UCC25701PW UCC25702D UCC25702N UCC25702PW UCC35701D UCC35701N UCC35701PW UCC35702D UCC35702N UCC35702PW The D and PW packages are available taped and reeled. Add TR suffix to the device type (e.g., UCC35701DTR). ELECTRICAL CHARACTERISTICS:Unless otherwise specified, VDD = 11V, RT = 60.4k, CT = 330pF, CREF = CVDD = 0.1m F, VFF = 2.0V, and no load on the outputs. PARAMETER TEST CONDITIONS MIN TYP MAX UNITS UVLO Section Start Threshold (UCCX5701) 12 13 14 V (UCCX5702) 8.8 9.6 10.4 V Stop Threshold (UCCX5701) 8 9 10 V (UCCX5702) 8.0 8.8 9.6 V Hysteresis (UCCX5701) 3 4 V (UCCX5702) 0.3 0.8 V Supply Current 130 200 mA Start-up Current (UCCX5701) VDD = 11V, VDD Comparator Off 120 190 mA (UCCX5702) VDD = 8V, VDD Comparator Off VDD Comparator On 0.75 1.5 mA IDD Active (UCCX5701) IDD = 10mA 13.5 14.3 15 V VDD Clamp Voltage 13 13.8 15 V (UCCX5702) IDD = 10mA (UCCX5701) 1.3 V VDD Clamp – Start Threshold (UCCX5702) 4.2 V Voltage Reference VDD = 10V to 13V, IVREF = 0mA to 2mA 4.9 5 5.1 V VREF 20 mV Line Regulation VDD = 10V to 13V 2 mV Load Regulation IVREF = 0mA to 2mA 20 50 mA Short Circuit Current VREF = 0V, TJ = 25°C 2 UCC15701/2 UCC25701/2 UCC35701/2 ELECTRICAL CHARACTERISTICS:Unless otherwise specified, VDD = 11V, RT = 60.4k, CT = 330pF, CREF = CVDD = 0.1m F, VFF = 2.0V, and no load on the outputs. PARAMETER TEST CONDITIONS MIN TYP MAX UNITS Line Sense Vth High Line Comparator 3.9 4 4.1 V Vth Low Line Comparator 0.5 0.6 0.7 V Input Bias Current –100 100 nA Oscillator Section 90 100 110 kHz Frequency VFF = 0.8V to 3.2V 90 100 110 kHz Frequency VFF = 0.6V to 3.4V (Note 1) SYNC VIH 2 V SYNC VIL 0.8 V SYNC Input Current VSYNC = 2.0V 3 10 mA RT Voltage VFF = 0.4V 0.5 0.6 0.7 V VFF = 0.8V 0.75 0.8 0.85 V VFF = 2.0V 1.95 2.0 2.05 V VFF = 3.2V 3.15 3.2 3.25 V VFF = 3.6V 3.3 3.4 3.5 V VFF = 0.8V (Note 1) 0.8 V CT Peak Voltage VFF = 3.2V (Note 1) 3.2 V (Note 1) 0 V CT Valley Voltage Soft Start/Shutdown/Duty Cycle Control Section 10 18 30 mA ISS Charging Current 300 500 750 mA ISS Discharging Current 25 100 mV Saturation VDD = 11V, IC Off Fault Counter Section Threshold Voltage VFF = 0.8V to 3.2V 3.8 4 4.2 V Saturation Voltage VFF = 0.8V to 3.2V 100 mV Count Charging Current 10 18 30 mA Current Limit Section Input Bias Current –100 0 100 nA Current Limit Threshold 180 200 220 mV Shutdown Threshold 500 600 700 mV Pulse Width Modulator Section FB Pin Input Impedance VFB = 3V 30 50 100 kW Minimum Duty Cycle VFB <= 1V 0 % Maximum Duty Cycle VFB >= 4.5V, VSCLAMP >= 2.0V 95 99 100 % PWM Gain VFF = 0.8V 35 50 70 %/V Volt Second Clamp Section Maximum Duty Cycle VFF = 0.8V, VSCLAMP = 0.6V 69 74 79 % Minimum Duty Cycle VFF = 3.2V, VSCLAMP = 0.6V 17 19 21 % Output Section 0.4 1 V VOH IOUT = –100mA, (VDD – VOUT) 0.4 1 V VOL IOUT = 100mA 20 100 ns Rise Time CLOAD = 1000pF 20 100 ns Fall Time CLOAD = 1000pF Note 1: Ensured by design. Not 100% tested in production. 3 UCC15701/2 UCC25701/2 UCC35701/2 DETAILED BLOCK DIAGRAM 2*IRT 11 S VFF 6 RT 7 CT 10 Q IRT 3 VDD 4 OUT 5 P GND P WM 0.2V S + VALLEY 8 1.5R VS CLAMP RD P EAK 0.7V FB S YNC 3m A Q RD R 9 4V HIGH LINE VREF I SS 0.6V 4.5V 14 S S DONE 0.6V ILIM 2 25*I CURRENT FAULT 0.2V CURRENT LIMIT VREF 0.2V D P WM S S DONE COUNT 13/9V (35701) 9.6/8.8V (35702) RUN LOW LINE 1 Q R Q VDD SD I R R Q SD 4V FAULT LATCH 5.0V REF 12 VREF 13 GND S HUTDOWN LATCH UDG-98004 PIN DESCRIPTIONS VDD: Power supply pin. A shunt regulator limits supply voltage to 14V typical at 10mA shunt current. RT: The voltage on this pin mirrors VFF over a 0.8V to 3.2V range. A resistor to ground sets the ramp capacitor charge current. The resistor value should be between 20k and 200k. PGND: Power Ground. Ground return for output driver and currents. GND: Analog Ground. Ground return for all other circuits. This pin must be connected directly to PGND on the board. CT: A capacitor to ground provides the oscillator/ feedforward sawtooth waveform. Charge current is 2 · IRT, resulting in a CT slope proportional to the input voltage. The ramp voltage range is GND to VRT. OUT: Gate drive output. Output resistance is 10W maximum. Period and oscillator frequency is given by: VFF: Voltage feedforward pin. This pin connects to the power supply input voltage through a resistive divider and provides feedforward compensation over a 0.8V to 3.2V range. A voltage greater than 4.0V or less than 0.6V on this pin initiates a soft stop cycle. 4 T= VR T · CT + t DIS CH » 0 . 5 · RT · CT 2 · IR T F» 2 R T · CT UCC15701/2 UCC25701/2 UCC35701/2 PIN DESCRIPTIONS (cont.) VSCLAMP: Voltage at this pin is compared to the CT voltage, providing a constant volt-second limit. The comparator output terminates the PWM pulse when the ramp voltage exceeds VSCLAMP. The maximum on time is given by: source. While the soft start capacitor is charging, and while VSS < (0.4 VFB), the duty cycle, and therefore the output voltage of the converter is determined by the soft start circuitry. At High Line or Low Line fault conditions, the soft start capacitor is discharged with a controlled discharge current of about 500mA. During the discharge time, the duty cycle of the converter is gradually decreased to zero. This soft stop feature allows the synchronous rectifiers to gradually discharge the output LC filter. An abrupt shut off can cause the LC filter to oscillate, producing unpredictable output voltage levels. V · CT t ON = VS CLAMP 2 · IR T The maximum duty cycle limit is given by: DMAX = t ON VVS CLAMP = T VR T FB: Input to the PWM comparator. This pin is intended to be driven with an optocoupler circuit. Input impedance is 50kW Typical modulation range is 1.6V to 3.6V. All other fault conditions (UVLO, VREF Low, Over Current (0.6V on ILIM) or COUNT) will cause an immediate stop of the converter. Furthermore, both the Over Current fault and the COUNT fault will be internally latched until VDD drops below 9V or VFF goes below the 600mV threshold at the input of the Low Line comparator. SYNC: Level sensitive oscillator sync input. A high level forces the gate drive output low and resets the ramp capacitor. On-time starts at the negative edge the pulse. There is a 3mA pull down current on the pin, allowing it to be disconnected when not used. After all fault conditions are cleared and the soft start capacitor is discharged below 200 mV, a soft start cycle will be initiated to restart the converter. VREF: 5.0V trimmed reference with 2% variation over line, load and temperature. Bypass with a minimum of 0.1mF to ground. ILIM: Provides a pulse by pulse current limit by terminating the PWM pulse when the input is above 200mV. An input over 600mV initiates a latched soft stop cycle. SS: Soft Start pin. A capacitor is connected between this pin and ground to set the start up time of the converter. After power up (VDD>13V AND VREF>4.5V), or after a fault condition has been cleared, the soft start capacitor is charged to VREF by a nominal 18mA internal current COUNT: Capacitor to ground integrates current pulses generated when ILIM exceeds 200mV. A resistor to ground sets the discharge time constant. A voltage over 4V will initiate a latched soft stop cycle. APPLICATION INFORMATION (Note: Refer to the Typical Application Diagram on the first page of this datasheet for external component names.) All the equations given below should be considered as first order approximations with final values determined empirically for a specific application. The circuit will start at this point. IVDD will increase from the start up value of 130mA to the run value of 750mA. The capacitor on SS is charged with a 18mA current. When the voltage on SS is greater than 0.8V, output pulses can begin, and supply current will increase to a level determined by the MOSFET gate charge requirements to IVDD ~ 1mA + QT · fs. When the output is active, the bootstrap winding should be sourcing the supply current. If VDD falls below the UVLO stop threshold, the controller will enter a shutdown sequence and turn the controller off, returning the start sequence to the initial condition. Power Sequencing VDD is normally connected through a high impedance (R6) to the input line, with an additional path (R7) to a low voltage bootstrap winding on the power transformer. VFF is connected through a divider (R1/R2) to the input line. For circuit activation, all of the following conditions are required: VDD Clamp An internal shunt regulator clamps VDD so the voltage does not exceed a nominal value of 14V. If the regulator is active, supply current must be limited to less than 20mA. 1. VFF between 0.6V and 4.0V (operational input voltage range). 2. VDD has been under the UVLO stop threshold to reset the shutdown latch. 3. VDD is over the UVLO start threshold. 5 UCC15701/2 UCC25701/2 UCC35701/2 APPLICATION INFORMATION (cont.) Output Inhibit VFF is intended to operate accurately over a 4:1 range between 0.8V and 3.2V. Voltages at VFF below 0.6V or above 4.0V will initiate a soft stop cycle and a chip restart when the under/over voltage condition is removed. During normal operation, OUT is driven high at the start of a clock period and is driven low by voltages on CT, FB or VSCLAMP. Volt-Second Clamp The following conditions cause the output to be immediately driven low until a clock period starts where none of the conditions are true: A constant volt-second clamp is formed by comparing the timing capacitor ramp voltage to a fixed voltage derived from the reference. Resistors R4 and R5 set the volt-second limit. For a volt-second product defined as VIN tON(max), the required voltage at VSCLAMP is: 1. ILIM > 0.2V 2. FB or SS is less than 0.8V æ R2 ö ÷ · VIN · t ON (ma x) ç èR1 + R 2 ø . RT · CT Current Limiting ( ILIM is monitored by two internal comparators. The current limit comparator threshold is 0.2V. If the current limit comparator is triggered, OUT is immediately driven low and held low for the remainder of the clock cycle, providing pulse-by-pulse over-current control for excessive loads. This comparator also causes CF to be charged for the remainder of the clock cycle. ) The duty cycle limit is then: VVS CLAMP , or VVFF If repetitive cycles are terminated by the current limit comparator causing COUNT to rise above 4V, the shutdown latch is set. The COUNT integration delay feature will be bypassed by the shutdown comparator which has a 0.6V threshold. The shutdown comparator immediately sets the shutdown latch. RF in parallel with CF resets the COUNT integrator following transient faults. RF must be greater than (4 · R4) · (1 – DMAX). VVS CLAMP . æ R2 ö ÷ VIN · ç èR1 + R 2 ø The maximum duty cycle is realized when the feedforward voltage is set at the low end of the operating range (VFF = 0.8V). The absolute maximum duty cycle is: DMAX = VVS CLAMP VR EF R5 = · 0.8 0.8 R 4 + R 5 Frequency Set Latched Shutdown The frequency is set by a resistor from RT to ground and a capacitor from CT to ground. The frequency is approxi2 mately: F = (RT · CT ) If ILIM rises above 0.6V, or COUNT rises to 4V, the shutdown latch will be set. This will force OUT low, discharge SS and COUNT, and reduce IDD to approximately 750mA. When, and if, VDD falls below the UVLO stop threshold, the shutdown latch will reset and IDD will fall to 130mA, allowing the circuit to restart. If VDD remains above the UVLO stop threshold (within the UVLO band), an alternate restart will occur if VFF is momentarily reduced below 1V. External shutdown commands from any source may be added into either the COUNT or ILIM pins. External synchronization is via the SYNC pin. The pin has a 1.5V threshold , making it compatible with 5V and 3.3V CMOS logic. The input is level sensitive, with a high input forcing the oscillator ramp low and the output low. An active pull down on the SYNC pin allows it to be unconnected when not used. Gate Drive Output Voltage Feedforward The UCC35701/2 is capable of a 1A peak output current. Bypass with at least 0.1mF directly to PGND. The capacitor must have a low equivalent series resistance and inductance. The connection from OUT to the power MOSFET gate should have a 2W or greater damping resistor and the distance between chip and MOSFET should be minimized. A low impedance path must be established between the MOSFET source (or ground side of the current sense resistor), the VDD capacitor and PGND. PGND should then be connected by a single path (shown as RGND) to GND. The voltage slope on CT is proportional to line voltage over a 4:1 range and equals 2·VFF (RT·CT). The capacitor charging current is set by the voltage across RT. V(RT) tracks VFF over a range of 0.8V to 3.2V. A changing line voltage will immediately change the slope of V(CT), changing the pulse width in a proportional manner without using the feedback loop, providing excellent dynamic line regulation. 6 UCC15701/2 UCC25701/2 UCC35701/2 APPLICATION INFORMATION (cont.) UCC35701/2 is pin to pin compatible to UCC3570 but is not a direct drop-in replacement for UCC3570 sockets. The changes required to the power supply printed circuit board of for existing UCC3570 designs are minimal. For conversion, only one extra resistor to set the volt-second clamp needs to be added to the existing PC board layouts. In addition, some component values will need to be changed due to the functionality change in of four of the IC pins. Transitioning From UCC3570 To UCC35701 The UCC35701/2 is an advanced version of the popular, low power UCC3570 PWM. Significant improvements were made to the IC’s oscillator and PWM control sections to enhance overall system performance. All of the key attributes and functional blocks of the UCC3570 were maintained in the UCC35701/2. A typical application using UCC3570 and UCC35701/2 is shown in Fig. 6 for comparison. The Pinout Changes from UCC3570 are as follows. The advantages of the UCC35701/2 over the UCC3570 are as follows. Pin 7 was changed from SLOPE to RT (for timing resistor) Improved oscillator and PWM control section. Pin 8 was changed from ISET to VSCLAMP (requiring one additional resistor from pin 9 to VREF) A precise maximum volt-second clamp circuit. The UCC3570 has a dual time base between oscillator and feedforward circuitry. The integated time base in UCC35701/2 improves the duty cycle clamp accuracy, providing better than ± 5% accurate volt- second clamp over full temperature range. Pin 10 was changed from RAMP to CT (single timing capacitor) Pin 11 was changed from FREQ to SYNC (input only) Additional Information Separately programmable oscillator timing resistor (RT) and capacitor (CT) circuits provide a higher degree of versatility. Please refer to the following two Unitrode application topics on UCC3570 for additional information. An independent SYNC input pin for simple external synchronization. [1] Application Note U-150, Applying the UCC3570 Voltage-Mode PWM Controller to Both Off-line and DC/DC Converter Designs by Robert A. Mammano A smaller value filter capacitor (0.1mF) can be used with the enhanced reference voltage. [2] Design Note DN-62, Switching Power Supply Topology, Voltage Mode vs. Current Mode by Robert Mammano TYPICAL WAVEFORMS FEEDBK VS CLAMP CT S OFTS T S OFT S TART HIGH DC LOW DC ZERO DC S OFT S TOP V-S CLAMP Figure 1. Timing diagram for PWM action with forward, soft start and volt-second clamp. 7 UDG-98207 UCC15701/2 UCC25701/2 UCC35701/2 TYPICAL WAVEFORMS (cont.) VFF CT S YNC UDG-98208 Figure 2. Timing diagram for oscillator waveforms showing feedforward action and synchronization. TYPICAL CHARACTERISTIC CURVES 1.03 1000 100 NORMALIZED DUTY CYCLE FREQUENCY [kHz] VFF=3.2 100pF 150pF 220pF 330pF 470pF 10 20 60 100 140 RT [K ] 180 NORMALIZED FREQUENCY 1 0.99 VFF=3.2 0.98 5 25 45 0.98 -35 -15 5 25 45 65 85 Figure 5. Normalized maximum duty cycle vs. temperature. VFF=0.8 -15 0.99 TEMPERATURE [°C] 1.01 -35 VFF=0.8 1.00 -55 CT=330pF FOSC = 100kHz -55 1.01 0.97 220 Figure 3. Oscillator frequency vs. RT and CT. 1.02 1.02 65 85 105 125 TEMPERATURE [°C] Figure 4. Oscillator frequency vs. temperature. 8 105 125 UCC15701/2 UCC25701/2 UCC35701/2 APPLICATION INFORMATION (cont.) VIN+ R1 R5 UCC3570 R2 6 VFF 7 S LOP E 10 RAMP 9 IS ET 11 FREQ 14 SS 1 COUNT R6 VDD 3 VOUT R3 CR C4 C1 R8 OUT 4 R4 R9 CT RT ILIM 2 C2 R S NS CS S CF RF P GND 5 R GND C3 12 VREF 8 FB R7 GND 13 R11 VOUT C5 R13 C6 R12 R14 C7 R15 VIN+ UCC35701 R1 R5 R2 R6 6 VFF VDD 3 VOUT R3 7 CT C4 RT C1 R8 10 CT OUT 4 9 ILIM 2 R4 R9 R NEW VS CLAMP C2 11 S YNC R S NS CS S 14 S S CF 1 RF P GND 5 COUNT R GND C3 12 VREF R7 GND 13 8 FB R11 VOUT C5 R12 R13 C6 R14 C7 R15 UDG-98210 Figure 6. Single-ended forward circuit comparison between UCC3570 and UCC37501. 9 UCC15701/2 UCC25701/2 UCC35701/2 REVISION HISTORY DATE 02/16/05 6/16/05 REVISION SLUS293B SLUS293C REASON Add FB to abs max table. Created revision history table. Updated block diagram and the SS pin description. 10 PACKAGE OPTION ADDENDUM www.ti.com 11-Apr-2013 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish (2) MSL Peak Temp Op Temp (°C) Top-Side Markings (3) (4) UCC15701J OBSOLETE CDIP J 14 TBD Call TI Call TI -55 to 125 UCC15701L OBSOLETE LCCC FK 20 TBD Call TI Call TI -55 to 125 UCC25701D ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 UCC25701D UCC25701DG4 ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 UCC25701D UCC25701DTR ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 UCC25701D UCC25701DTRG4 ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 UCC25701D UCC25701N ACTIVE PDIP N 14 25 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type -40 to 85 UCC25701N UCC25701NG4 ACTIVE PDIP N 14 25 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type -40 to 85 UCC25701N UCC25701PW ACTIVE TSSOP PW 14 90 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR -40 to 85 25701 UCC25701PWG4 ACTIVE TSSOP PW 14 90 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR -40 to 85 25701 UCC25701PWTR ACTIVE TSSOP PW 14 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR -40 to 85 25701 UCC25701PWTRG4 ACTIVE TSSOP PW 14 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR -40 to 85 25701 UCC25702D ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 UCC25702D UCC25702DG4 ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 UCC25702D UCC25702DTR ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 UCC25702D UCC25702DTRG4 ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 UCC25702D UCC25702N ACTIVE PDIP N 14 25 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type -40 to 85 UCC25702N UCC25702NG4 ACTIVE PDIP N 14 25 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type -40 to 85 UCC25702N Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com 11-Apr-2013 Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish (2) MSL Peak Temp Op Temp (°C) Top-Side Markings (3) (4) UCC25702PW ACTIVE TSSOP PW 14 90 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR -40 to 85 25702 UCC25702PWG4 ACTIVE TSSOP PW 14 90 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR -40 to 85 25702 UCC25702PWTR ACTIVE TSSOP PW 14 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR -40 to 85 25702 UCC25702PWTRG4 ACTIVE TSSOP PW 14 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR -40 to 85 25702 UCC35701D ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 0 to 70 UCC35701D UCC35701DG4 ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 0 to 70 UCC35701D UCC35701DTR ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 0 to 70 UCC35701D UCC35701DTRG4 ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 0 to 70 UCC35701D UCC35701N ACTIVE PDIP N 14 25 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type 0 to 70 UCC35701N UCC35701NG4 ACTIVE PDIP N 14 25 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type 0 to 70 UCC35701N UCC35701PW ACTIVE TSSOP PW 14 90 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR 0 to 70 35701 UCC35701PWG4 ACTIVE TSSOP PW 14 90 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR 0 to 70 35701 UCC35701Q OBSOLETE UTR 20 TBD Call TI Call TI 0 to 70 UCC35701QTR OBSOLETE UTR 20 TBD Call TI Call TI 0 to 70 UCC35702D ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 0 to 70 UCC35702D UCC35702DG4 ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 0 to 70 UCC35702D UCC35702N ACTIVE PDIP N 14 25 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type 0 to 70 UCC35702N UCC35702NG4 ACTIVE PDIP N 14 25 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type 0 to 70 UCC35702N UCC35702PW ACTIVE TSSOP PW 14 90 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR 0 to 70 35702 Addendum-Page 2 Samples PACKAGE OPTION ADDENDUM www.ti.com Orderable Device 11-Apr-2013 Status (1) UCC35702PWG4 ACTIVE Package Type Package Pins Package Drawing Qty TSSOP PW 14 90 Eco Plan Lead/Ball Finish (2) Green (RoHS & no Sb/Br) MSL Peak Temp Op Temp (°C) Top-Side Markings (3) CU NIPDAU Level-2-260C-1 YEAR (4) 0 to 70 35702 (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) Multiple Top-Side Markings will be inside parentheses. Only one Top-Side Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Top-Side Marking for that device. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. OTHER QUALIFIED VERSIONS OF UCC15701, UCC35701 : • Catalog: UCC35701 • Military: UCC15701 Addendum-Page 3 Samples PACKAGE OPTION ADDENDUM www.ti.com 11-Apr-2013 NOTE: Qualified Version Definitions: • Catalog - TI's standard catalog product • Military - QML certified for Military and Defense Applications Addendum-Page 4 PACKAGE MATERIALS INFORMATION www.ti.com 26-Jan-2013 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant UCC25701DTR SOIC D 14 2500 330.0 16.4 6.5 9.0 2.1 8.0 16.0 Q1 UCC25701PWTR TSSOP PW 14 2000 330.0 12.4 6.9 5.6 1.6 8.0 12.0 Q1 UCC25702DTR SOIC D 14 2500 330.0 16.4 6.5 9.0 2.1 8.0 16.0 Q1 UCC25702PWTR TSSOP PW 14 2000 330.0 12.4 6.9 5.6 1.6 8.0 12.0 Q1 UCC35701DTR SOIC D 14 2500 330.0 16.4 6.5 9.0 2.1 8.0 16.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 26-Jan-2013 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) UCC25701DTR SOIC D 14 2500 333.2 345.9 28.6 UCC25701PWTR TSSOP PW 14 2000 367.0 367.0 35.0 UCC25702DTR SOIC D 14 2500 333.2 345.9 28.6 UCC25702PWTR TSSOP PW 14 2000 367.0 367.0 35.0 UCC35701DTR SOIC D 14 2500 333.2 345.9 28.6 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2013, Texas Instruments Incorporated