PHOTOCOUPLER PS9117A HIGH CMR, 10 Mbps OPEN COLLECTOR OUTPUT TYPE 5-PIN SOP (SO-5) −NEPOC HIGH-SPEED PHOTOCOUPLER Series− DESCRIPTION The PS9117A is an optically coupled high-speed, active low type isolator containing a GaAlAs LED on the input side and a photodiode and a signal processing circuit on the output side on one chip. The PS9117A is designed specifically for high common mode transient immunity (CMR) and low pulse width distortion. The PS9117A is suitable for high density application. FEATURES • Pulse width distortion ( tPHL − tPLH = 35 ns MAX.) PIN CONNECTION (Top View) • High common mode transient immunity (CMH, CML = ±15 kV/µs MIN.) • Small package (SO-5) 5 4 3 • High-speed (10 Mbps) 1. Anode 2. Cathode 3. GND 4. VO 5. VCC • High isolation voltage (BV = 3 750 Vr.m.s.) • Open collector output • Ordering number of taping product: PS9117A-F3: 2 500 pcs/reel • Pb-Free product 1 2 APPLICATIONS • Measurement equipment • PDP • FA Network TRUTH TABLE LED Output ON L OFF H Document No. PN10646EJ01V0DS (1st edition) Date Published November 2006 NS CP(K) 2006 PS9117A PACKAGE DIMENSIONS (UNIT: mm) 3.4 5 +0.3 –0.1 4 3 7.0±0.3 4.4 2 2.6±0.2 0.15 +0.10 –0.05 1 0.5±0.3 0.1±0.1 1.27 0.4 +0.10 –0.05 0.25 M MARKING EXAMPLE 117A N631 No. 1 pin Mark Initial of NEC (Engraved mark) N Assembly Lot *1 N 6 31 Week Assembled Year Assembled (Last 1 Digit) Rank Code *1 2 Bar : Pb-Free Preliminary Data Sheet PN10646EJ01V0DS PS9117A ORDERING INFORMATION Part Number Order Number Solder Plating Packing Style Safety Standards Application Part Approval Number Specification PS9117A PS9117A-A PS9117A-F3 Pb-Free 20 pcs (Tape 20 pcs cut) Standard products PS9117A-F3-A Embossed Tape 2 500 pcs/reel (UL approved) PS9117A-V PS9117A-V-A 20 pcs (Tape 20 pcs cut) DIN EN60747-5-2 PS9117A-V-F3 PS9117A-V-F3-A Embossed Tape 2 500 pcs/reel (VDE0884 Part2) *1 PS9117A approved (Option) *1 For the application of the Safety Standard, following part number should be used. ABSOLUTE MAXIMUM RATINGS (TA = 25°C, unless otherwise specified) Parameter Symbol Ratings Unit IF 30 mA Reverse Voltage VR 5 V Supply Voltage VCC 7 V Output Voltage VO 7 V IO 25 mA PC 40 mW BV 3 750 Vr.m.s. Operating Ambient Temperature TA −40 to +85 °C Storage Temperature Tstg −55 to +125 °C Diode Detector Forward Current *1 Output Current Power Dissipation Isolation Voltage *2 *3 *1 Reduced to 0.3 mA/°C at TA = 25°C or more. *2 Applies to output pin VO (collector pin). Reduced to 1.5 mW/°C at TA = 65°C or more. *3 AC voltage for 1 minute at TA = 25°C, RH = 60% between input and output. Pins 1-2 shorted together, 3-5 shorted together. RECOMMENDED OPERATING CONDITIONS Parameter Symbol MIN. Low Level Input Voltage VFL 0 High Level Input Current IFH 6.3 Supply Voltage VCC 4.5 TTL (RL = 1 kΩ, loads) N Pull-up Resistor RL TYP. MAX. Unit 0.8 V 10 12.5 mA 5.0 5.5 V 5 330 4k Ω Preliminary Data Sheet PN10646EJ01V0DS 3 PS9117A ELECTRICAL CHARACTERISTICS (TA = −40 to +85°C, unless otherwise specified) Parameter Diode Symbol Conditions MIN. *1 Unit 1.8 V 10 µA VF IF = 10 mA, TA = 25°C Reverse Current IR VR = 3 V, TA = 25°C Terminal Capacitance Ct V = 0 V, f = 1 MHz, TA = 25°C 30 IOH VCC = VO = 5.5 V, VF = 0.8 V 1 100 µA VOL VCC = 5.5 V, IF = 5 mA, IOL = 8 mA 0.2 0.6 V High Level Supply Current ICCH VCC = 5.5 V, IF = 0 mA, VO = open 4 7 mA Low Level Supply Current ICCL VCC = 5.5 V, IF = 10 mA, VO = open 6 10 IFHL VCC = 5 V, VO = 0.8 V, RL = 350 Ω 2 5 RI-O VI-O = 1 kVDC, RH = 40 to 60%, Low Level Output Voltage *2 Coupled Threshold Input Current 1.65 MAX. Forward Voltage Detector High Level Output Current 1.4 TYP. pF (H → L) Isolation Resistance 10 Ω 11 TA = 25°C Isolation Capacitance CI-O V = 0 V, f = 1 MHz, TA = 25°C 0.6 Propagation Delay Time tPHL TA = 25°C 40 (H → L) *3 pF 75 ns 100 Propagation Delay Time tPLH TA = 25°C 45 (L → H) *3 75 100 Rise Time tr VCC = 5 V, RL = 350 Ω, IF = 7.5 mA 20 Fall Time tf VTHHL = VTHLH = 1.5 V 5 Pulse Width Distortion tPHL-tPLH 5 35 *3 (PWD) Propagation Delay Skew tPSK Common Mode CMH Common Mode 4 15 20 kV/µs 15 20 kV/µs *4 Transient Immunity at Low Level Output VCC = 5 V, RL = 350 Ω, TA = 25°C, IF = 0 mA, VO > 2 V, VCM = 1 kV Transient Immunity at High Level Output 40 CML VCC = 5 V, RL = 350 Ω, TA = 25°C, IF = 7.5 mA, VO < 0.8 V, VCM = 1 kV *4 Preliminary Data Sheet PN10646EJ01V0DS PS9117A *1 Typical values at TA = 25°C *2 Because VOL of 2 V or more may be output when LED current input and when output supply of VCC = 2.6 V or less, it is important to confirm the characteristics (operation with the power supply on and off) during design, before using this device. *3 Test circuit for propagation delay time (IF = 7.5 mA) 50% Input VCC = 5 V Pulse input (IF) 0.1 µ F (PW = 1 µ s, Duty cycle = 1/10) Input (monitor) RL = 350 Ω VO (monitor) CL = 15 pF Output 47 Ω tPHL 1.5 V VOL tPLH Remark CL includes probe and stray wiring capacitance. *4 Test circuit for common mode transient immunity SW 1 kV VCM 90% IF VCC = 5 V 0.1 µ F 10% RL = 350 Ω VO (monitor) 0V tr CL = 15 pF VO (IF = 0 mA) VCM VO (IF = 7.5 mA) tf VOH 2V 0.8 V VOL Remark CL includes probe and stray wiring capacitance. USAGE CAUTIONS 1. This product is weak for static electricity by designed with high-speed integrated circuit so protect against static electricity when handling. 2. By-pass capacitor of 0.1 µF is used between VCC and GND near device. Also, ensure that the distance between the leads of the photocoupler and capacitor is no more than 10 mm. 3. Avoid storage at a high temperature and high humidity. Preliminary Data Sheet PN10646EJ01V0DS 5 PS9117A TAPING SPECIFICATIONS (UNIT: mm) 1.55±0.1 7.4±0.1 5.5±0.1 1.5+0.1 –0 12.0±0.2 2.0±0.05 4.0±0.1 1.75±0.1 Outline and Dimensions (Tape) 3.9±0.1 8.0±0.1 3.45 MAX. 3.0±0.1 0.3±0.05 Tape Direction PS9117A-F3 Outline and Dimensions (Reel) 2.0±0.5 2.0±0.5 φ 100±1.0 21.0±0.8 φ 13.0±0.2 R 1.0 φ 330±2.0 13.0±0.2 13.5±1.0 17.5±1.0 Packing: 2 500 pcs/reel 6 Preliminary Data Sheet PN10646EJ01V0DS 11.9 to 15.4 Outer edge of flange PS9117A NOTES ON HANDLING 1. Recommended soldering conditions (1) Infrared reflow soldering • Peak reflow temperature 260°C or below (package surface temperature) • Time of peak reflow temperature 10 seconds or less • Time of temperature higher than 220°C 60 seconds or less • Time to preheat temperature from 120 to 180°C 120±30 s • Number of reflows Three • Flux Rosin flux containing small amount of chlorine (The flux with a maximum chlorine content of 0.2 Wt% is recommended.) Package Surface Temperature T (˚C) Recommended Temperature Profile of Infrared Reflow (heating) to 10 s 260˚C MAX. 220˚C to 60 s 180˚C 120˚C 120±30 s (preheating) Time (s) (2) Wave soldering • Temperature 260°C or below (molten solder temperature) • Time 10 seconds or less • Preheating conditions 120°C or below (package surface temperature) • Number of times One (Allowed to be dipped in solder including plastic mold portion.) • Flux Rosin flux containing small amount of chlorine (The flux with a maximum chlorine content of 0.2 Wt% is recommended.) (3) Soldering by Soldering Iron • Peak Temperature (lead part temperature) 350°C or below • Time (each pins) 3 seconds or less • Flux Rosin flux containing small amount of chlorine (The flux with a maximum chlorine content of 0.2 Wt% is recommended.) (a) Soldering of leads should be made at the point 1.5 to 2.0 mm from the root of the lead (b) Please be sure that the temperature of the package would not be heated over 100°C Preliminary Data Sheet PN10646EJ01V0DS 7 PS9117A (4) Cautions • Fluxes Avoid removing the residual flux with freon-based and chlorine-based cleaning solvent. 2. Cautions regarding noise Be aware that when voltage is applied suddenly between the photocoupler’s input and output or between collector-emitters at startup, the output transistor may enter the on state, even if the voltage is within the absolute maximum ratings. USAGE CAUTIONS 1. Protect against static electricity when handling. 2. Avoid storage at a high temperature and high humidity. 8 Preliminary Data Sheet PN10646EJ01V0DS PS9117A • The information in this document is current as of November, 2006. The information is subject to change without notice. For actual design-in, refer to the latest publications of NEC Electronics data sheets or data books, etc., for the most up-to-date specifications of NEC Electronics products. Not all products and/or types are available in every country. Please check with an NEC Electronics sales representative for availability and additional information. • No part of this document may be copied or reproduced in any form or by any means without the prior written consent of NEC Electronics. NEC Electronics assumes no responsibility for any errors that may appear in this document. • NEC Electronics does not assume any liability for infringement of patents, copyrights or other intellectual property rights of third parties by or arising from the use of NEC Electronics products listed in this document or any other liability arising from the use of such products. No license, express, implied or otherwise, is granted under any patents, copyrights or other intellectual property rights of NEC Electronics or others. • Descriptions of circuits, software and other related information in this document are provided for illustrative purposes in semiconductor product operation and application examples. The incorporation of these circuits, software and information in the design of a customer's equipment shall be done under the full responsibility of the customer. NEC Electronics assumes no responsibility for any losses incurred by customers or third parties arising from the use of these circuits, software and information. • While NEC Electronics endeavors to enhance the quality, reliability and safety of NEC Electronics products, customers agree and acknowledge that the possibility of defects thereof cannot be eliminated entirely. To minimize risks of damage to property or injury (including death) to persons arising from defects in NEC Electronics products, customers must incorporate sufficient safety measures in their design, such as redundancy, fire-containment and anti-failure features. • NEC Electronics products are classified into the following three quality grades: "Standard", "Special" and "Specific". The "Specific" quality grade applies only to NEC Electronics products developed based on a customerdesignated "quality assurance program" for a specific application. The recommended applications of an NEC Electronics product depend on its quality grade, as indicated below. Customers must check the quality grade of each NEC Electronics product before using it in a particular application. "Standard": Computers, office equipment, communications equipment, test and measurement equipment, audio and visual equipment, home electronic appliances, machine tools, personal electronic equipment and industrial robots. "Special": Transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster systems, anti-crime systems, safety equipment and medical equipment (not specifically designed for life support). "Specific": Aircraft, aerospace equipment, submersible repeaters, nuclear reactor control systems, life support systems and medical equipment for life support, etc. The quality grade of NEC Electronics products is "Standard" unless otherwise expressly specified in NEC Electronics data sheets or data books, etc. If customers wish to use NEC Electronics products in applications not intended by NEC Electronics, they must contact an NEC Electronics sales representative in advance to determine NEC Electronics' willingness to support a given application. (Note) (1) "NEC Electronics" as used in this statement means NEC Electronics Corporation and also includes its majority-owned subsidiaries. (2) "NEC Electronics products" means any product developed or manufactured by or for NEC Electronics (as defined above). M8E 02. 11-1 Preliminary Data Sheet PN10646EJ01V0DS 9 PS9117A Caution GaAs Products This product uses gallium arsenide (GaAs). GaAs vapor and powder are hazardous to human health if inhaled or ingested, so please observe the following points. • Follow related laws and ordinances when disposing of the product. If there are no applicable laws and/or ordinances, dispose of the product as recommended below. 1. Commission a disposal company able to (with a license to) collect, transport and dispose of materials that contain arsenic and other such industrial waste materials. 2. Exclude the product from general industrial waste and household garbage, and ensure that the product is controlled (as industrial waste subject to special control) up until final disposal. • Do not burn, destroy, cut, crush, or chemically dissolve the product. • Do not lick the product or in any way allow it to enter the mouth. 4590 Patrick Henry Drive Santa Clara, CA 95054-1817 Telephone: (408) 919-2500 Facsimile: (408) 988-0279 Subject: Compliance with EU Directives CEL certifies, to its knowledge, that semiconductor and laser products detailed below are compliant with the requirements of European Union (EU) Directive 2002/95/EC Restriction on Use of Hazardous Substances in electrical and electronic equipment (RoHS) and the requirements of EU Directive 2003/11/EC Restriction on Penta and Octa BDE. CEL Pb-free products have the same base part number with a suffix added. The suffix –A indicates that the device is Pb-free. The –AZ suffix is used to designate devices containing Pb which are exempted from the requirement of RoHS directive (*). In all cases the devices have Pb-free terminals. All devices with these suffixes meet the requirements of the RoHS directive. This status is based on CEL’s understanding of the EU Directives and knowledge of the materials that go into its products as of the date of disclosure of this information. Restricted Substance per RoHS Concentration Limit per RoHS (values are not yet fixed) Concentration contained in CEL devices -A Not Detected Lead (Pb) < 1000 PPM Mercury < 1000 PPM Not Detected Cadmium < 100 PPM Not Detected Hexavalent Chromium < 1000 PPM Not Detected PBB < 1000 PPM Not Detected PBDE < 1000 PPM Not Detected -AZ (*) If you should have any additional questions regarding our devices and compliance to environmental standards, please do not hesitate to contact your local representative. Important Information and Disclaimer: Information provided by CEL on its website or in other communications concerting the substance content of its products represents knowledge and belief as of the date that it is provided. CEL bases its knowledge and belief on information provided by third parties and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. CEL has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. CEL and CEL suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall CEL’s liability arising out of such information exceed the total purchase price of the CEL part(s) at issue sold by CEL to customer on an annual basis. See CEL Terms and Conditions for additional clarification of warranties and liability.