CM2500 WIDE INPUT 2A STEP DOWN CONVERTER GENERAL DESCRIPTION FEATURES The CM2500 is a current-mode step-down DC-DC converter 2A Output Current that generates up to 2A output current at 380kHz switching Up to 95% Efficiency frequency. The device utilizes advanced BCD process for 4.75V to 20V Input Range operation with input voltage up to 20V consuming only 20μA 20μA Shutdown Supply Current in shutdown mode, the CM2500 is highly efficient with peak 380kHz Switching Frequency efficiency at 95% when in operation. Adjustable Output Voltage from 1.28V to 0.85·VIN Cycle-by-Cycle Current Limit Protection Protection features include cycle-by-cycle current limit, Thermal Shutdown Protection thermal shutdown, and frequency fold back at short circuit. Frequency Fold Back at Short Circuit Stability with Wide Range of Capacitors, SOP-8 Package The CM2500 is available in SOP-8 package and requires very few external devices for operation. APPLICATIONS TFT LCD Monitors Portable DVDs Car-Powered or Battery-Powered Equipments Set-Top Boxes Telecom Power Supplies DSL and Cable Modems and Routers Termination Supplies TYPICAL APPLICATIONS 2008/04/15 Rev1.0 Champion Microelectronic Corporation Page 1 CM2500 WIDE INPUT 2A STEP DOWN CONVERTER PIN CONFIGURATION BLOCK DIAGRAM 2008/04/15 Rev1.0 Champion Microelectronic Corporation Page 2 CM2500 WIDE INPUT 2A STEP DOWN CONVERTER ORDERING INFORMATION Part Number Temperature Range Package Packing CM2500GIS -40℃ ~ +85℃ SOP-8 TAPE & REEL ABSOLUTE MAXIMUM RATINGS OPERATING RATINGS Input Voltage Ambient Temperature Range (TA) …..…..... -40℃ to +85℃ …………….……..……………… -0.3V to +25V Output Current …………………….…… PD / (VIN - Vo) mA Output Voltage ………………….…… GND-0.3V to VIN+0.3V Junction Temperature Range ……...…... -40℃ to +150℃ ESD Classification …………………………………………… B PIN DESCRIPTION Pin Number Pin Name 1 BS Pin Description Bootstrap. This pin acts as the positive rail for the high-side switch’s gate driver. Connect a 10nF capacitor between BS and SW. 2 IN 3 SW 4 GND 5 FB Input Supply. Bypass this pin to G with a low ESR capacitor. See Input Capacitor in the Application Information section. Switch Output. Connect this pin to the switching end of the inductor. Ground. Feedback Input. The voltage at this pin is regulated to 1.28V. Connect to the resistor divider between output and ground to set output voltage. 6 COMP Compensation Pin. See Stability Compensation in the Application Information section. 7 EN Enable Input. When higher than 1.85V, this pin turns the IC on. When lower than 1.7V, this pin turns the IC off. Output voltage is discharged when the IC is off. When left unconnected, EN is pulled up to 4.5V tip with a 2.5μA pullup current. 8 2008/04/15 Rev1.0 N/C Not Connected. Champion Microelectronic Corporation Page 3 CM2500 WIDE INPUT 2A STEP DOWN CONVERTER ABSOLUTE MAXIMUM RATINGS (Note: Exceeding these limits may damage the device. Exposure to absolute maximum rating conditions for long periods may affect device reliability.) PARAMETER VALUE UNIT IN Supply Voltage -0.3 to 20 V SW Voltage -1 to VIN + 1 V BS Voltage VSW – 0.3 to VSW + 6 V -0.3 to 6 V EN, FB, COMP Voltage Continuous SW Current Internally Limited A Junction to Ambient Thermal Resistance(θJA) 105 °C/W Maximum Power Dissipation 0.76 W Operating Junction Temperature -40 to 150 °C Storage Temperature -55 to 150 °C 300 °C Lead Temperature (Soldering, 10 sec) APPLICATION CIRCUIT 2008/04/15 Rev1.0 Champion Microelectronic Corporation Page 4 CM2500 WIDE INPUT 2A STEP DOWN CONVERTER ELECTRICAL CHARACTERISTICS (VIN = 12V, TA= 25°C unless otherwise specified.) PARAMETER SYMBOL TEST CONDITIONS Input Voltage VIN VOUT = 5V, ILOAD = 0A to 1A Feedback Voltage VFB 4.75V ≤ VIN ≤ 20V, VCOMP =1.5V MIN TYP 7 1.184 1.222 MAX UNIT 20 V 1.258 V High-Side Switch On Resistance RONH 0.22 Ω Low-Side Switch On Resistance RONL 4.7 Ω SW Leakage Current Limit COMP to Current Limit Transconductance VEN = 0 ILIM GEA Error Amplifier DC Gain AVEA ΔICOMP = ±10μA fSW Short Circuit Switching Frequency Maximum Duty Cycle 2.6 GCOMP Error Amplifier Transconductance Switching Frequency 1 DMAX 300 10 μA 3.3 A 1.8 A/V 550 μA/V 3200 V/V 360 420 kHz VFB = 0 50 kHz VFB = 1.1V 90 % Minimum Duty Cycle VFB = 1.4V Enable Threshold Voltage Hysteresis = 0.1V Enable Pull Up Current 0 2.2 V Pin pulled up to 4.5V typically when left unconnected 2.5 uA Supply Current in Shutdown VEN=0 20 50 uA IC Supply Current in Operation VEN=3V , VFB=1.4V 1.0 1.5 mA Thermal Shutdown Temperature Hysteresis=10°C 168 2008/04/15 Rev1.0 Champion Microelectronic Corporation 2.0 % °C Page 5 CM2500 WIDE INPUT 2A STEP DOWN CONVERTER FUNCTIONAL DESCRIPTION APPLICATION INFORMATION As seen in Figure 2, Functional Block Diagram, the CM2500 OUTPUT VOLTAGE SETTING is a current mode pulse width modulation (PWM) converter. The converter operates as follows : A switching cycle starts when the rising edge of the Oscillator clock output causes the High- Side Power Switch to turn on and the Low-Side Power Switch to turn off. With the SW side of the inductor now connected to IN, the inductor current ramps up to store energy in the magnetic field. The inductor current level is measured by the Current Sense Amplifier and added to the Oscillator ramp signal. If the resulting summation is higher than the COMP voltage, the output of the PWM Comparator Figure 4 shows the connections for setting the output voltage. goes high. When this happens or when Oscillator clock Select the proper ratio of the two feedback resistors RFB1 and output goes low, the High-Side Power Switch turns off and RFB2 based on the output voltage. Typically, use RFB2 ≈ the Low-Side Power Switch turns on. At this point, the SW 10kΩ and determine RFB1 from the following equation: side of the inductor swings to a diode voltage below ground, causing the inductor current to decrease and magnetic energy to be transferred to output. This state continues until the cycle starts again. The High-Side Power Switch is driven by logic using BS as the positive rail. This pin is charged to VSW + 6V when the Low-Side Power Switch turns on. The COMP voltage is the integration of the error between FB input and the internal 1.28V reference. If FB is lower than the reference voltage, COMP tends to go higher to increase current to the output. Current limit happens when COMP reaches its maximum clamp value of 2.55V. The Oscillator normally switches at 380kHz. However, if FB INDUCTOR SELECTION The inductor maintains a continuous current to the output load. This inductor current has a ripple that is dependent on the inductance value: higher inductance reduces the peak-to-peak ripple current. The trade off for high inductance value is the increase in inductor core size and series resistance, and the reduction in current handling capability. In general, select an inductance value L based on the ripple current requirement: voltage is less than 0.7V, then the switching frequency decreases until it reaches a minimum of 50kHz at VFB = 0.5V. where VIN is the input voltage, VOUT is the output voltage, SHUTDOWN CONTROL fSW is the switching frequency, IOUTMAX is the maximum The CM2500 has an enable input EN for turning the IC on or output current, and KRIPPLE is the ripple factor. Typically, off. When EN is less than 1.8V, the IC is in 8μA low current choose KRIPPLE = 30% to correspond to the peak-to-peak shutdown mode and output is discharged through the Low- ripple current being 30% of the maximum output current. With Side Power Switch. When EN is higher than 1.85V, the IC is this inductor value, the peak inductor current is IOUT • (1 + in normal operation mode. EN is internally pulled up with a KRIPPLE / 2). Make sure that this peak inductor current is less 2.5μA current source and can be left unconnected for that the 3A current limit. Finally, select the inductor core size so always-on operation. Note that EN is a low voltage input with that it does not saturate at 3A. Typical inductor values for a maximum voltage of 6V; it should never be directly various output voltages are shown in Table 1. connected to IN. Table 1. Typical Inductor Values THERMAL SHUTDOWN VOUT 1.5V 1.8V 2.5V 3.3V 5V The CM2500 automatically turns off when its junction L 6.8μH 6.8μH 10μH 15μH 22μH temperature exceeds 170°C. 2008/04/15 Rev1.0 Champion Microelectronic Corporation Page 6 CM2500 WIDE INPUT 2A STEP DOWN CONVERTER STABILITY COMPENSATION INPUT CAPACITOR The input capacitor needs to be carefully selected to maintain sufficiently low ripple at the supply input of the converter. A low ESR capacitor is highly recommended. Since large current flows in and out of this capacitor during switching, its ESR also affects efficiency. The input capacitance needs to be higher than 10μF. The best choice is the ceramic type; however, low ESR tantalum or electrolytic types may also be used provided that the RMS ripple current rating is higher than 50% of the output current. The input capacitor should be placed close to the IN and G The feedback loop of the IC is stabilized by the components at pins of the IC, with the shortest traces possible. In the case the COMP pin, as shown in Figure 5. The DC loop gain of the of tantalum or electrolytic types, they can be further away if a system is determined by the following equation: small parallel 0.1μF ceramic capacitor is placed right next to the IC. OUTPUT CAPACITOR The output capacitor also needs to have low ESR to keep low output voltage ripple. The output ripple voltage is: where IOUTMAX is the maximum output current, KRIPPLE is the ripple factor, RESR is the ESR of the output capacitor, fSW is the switching frequency, L is the inductor value, and COUT is the output capacitance. In the case of ceramic output capacitors, RESR is very small and does not contribute to the ripple. Therefore, a lower capacitance value can be used for ceramic capacitors. In the case of tantalum or electrolytic capacitors, the ripple is dominated by RESR multiplied by the ripple current. In that case, the output capacitor is chosen to have sufficiently low ESR. For ceramic output capacitors, typically choose a capacitance of about 22μF. For tantalum or electrolytic capacitors, choose a capacitor with less than 50mΩ ESR. RECTIFIER DIODE Use a Schottky diode as the rectifier to conduct current when the High-Side Power Switch is off. The Schottky diode must have a current rating higher than the maximum output current and a reverse voltage rating higher than the maximum input voltage. 2008/04/15 Rev1.0 Champion Microelectronic Corporation Page 7 CM2500 WIDE INPUT 2A STEP DOWN CONVERTER STEP 2. Set the zero fZ1 at 1/4 of the crossover frequency. If RCOMP is less than 15kΩ, the equation for CCOMP is: If RCOMP is limited to 15kΩ, then the actual cross over frequency is 3.4 / (VOUTCOUT). Therefore: STEP 3. If the output capacitor’s ESR is high enough to cause a zero at lower than 4 times the crossover frequency, an additional compensation capacitor CCOMP2 is required. The condition for using CCOMP2 is: RESRCOUT And the proper value for CCOMP2 is: Though CCOMP2 is unnecessary when the output capacitor has sufficiently low ESR, a small value CCOMP2 such as 100pF may improve stability against PCB layout parasitic effects. Table 2 shows some calculated results based on the compensation method above. Table 2. Typical Compensation for Different Output Voltages and Output Capacitors VOUT COUT RCOMP CCOMP CCOMP2 2.5V 22μF Ceramic 8.2kΩ 2.2nF None 3.3V 22μF Ceramic 12kΩ 1.5nF None 5V 22μF Ceramic 15kΩ 1.5nF None 2.5V 47μF SP Cap 15kΩ 1.5nF None 3.3V 47μF SP Cap 15kΩ 1.8nF None 5V 47μF SP Cap 15kΩ 2.7nF None 2.5V 470μF/6.3V/30mΩ 15kΩ 15nF 1nF 3.3V 470μF/6.3V/30mΩ 15kΩ 22nF 1nF 5V 470μF/10V/30mΩ 15kΩ 27nF None 2008/04/15 Rev1.0 Champion Microelectronic Corporation Page 8 CM2500 WIDE INPUT 2A STEP DOWN CONVERTER TYPICAL PERFORMANCE CHARACTERISTICS 2008/04/15 Rev1.0 Champion Microelectronic Corporation Page 9 CM2500 WIDE INPUT 2A STEP DOWN CONVERTER PACKAGE DIMENSION SOP-8 2008/04/15 Rev1.0 Champion Microelectronic Corporation Page 10 CM2500 WIDE INPUT 2A STEP DOWN CONVERTER IMPORTANT NOTICE Champion Microelectronic Corporation (CMC) reserves the right to make changes to its products or to discontinue any integrated circuit product or service without notice, and advises its customers to obtain the latest version of relevant information to verify, before placing orders, that the information being relied on is current. A few applications using integrated circuit products may involve potential risks of death, personal injury, or severe property or environmental damage. CMC integrated circuit products are not designed, intended, authorized, or warranted to be suitable for use in life-support applications, devices or systems or other critical applications. Use of CMC products in such applications is understood to be fully at the risk of the customer. In order to minimize risks associated with the customer’s applications, the customer should provide adequate design and operating safeguards. HsinChu Headquarter Sales & Marketing 5F, No. 11, Park Avenue II, Science-Based Industrial Park, HsinChu City, Taiwan 7F-6, No.32, Sec. 1, Chenggong Rd., Nangang District, Taipei City 115, Taiwan T E L : +886-3-567 9979 F A X : +886-3-567 9909 T E L : +886-2-2788 0558 F A X : +886-2-2788 2985 2008/04/15 Rev1.0 Champion Microelectronic Corporation Page 11