CHINA SEMICONDUCTOR CORPORATION Spec. No. PS-LU-U30AHR4-A0R A Rev. PRODUCT SPECIFICATION Model No ：CSPR-U30AHR4-A0R Descriptions: ■LED Type : Superbright Lamp ■LED Package : Piranha LED Lamp ■Emitting Color：Red ■Viewing Angle：60° ■Stopper CUSTOMER APPROVED SIGNATURES APPROVED BY CHECKED BY PREPARED BY CHINA SEMICONDUCTOR CORPORATION Address:2FL. NO.909,Chung-Cheng Road, Chung-Ho City Taipei Hsien,Taiwan. OPTO PLUS TECHNOLOGIES CO.,LTD Address:696 Shun jiang Rd.,Ji Shan St.Shaoxing, ZheJiang,China Tel:886-2-2223-9696 Fax:886-2-2223-9377 Tel:86-0575-88623888 Fax:86-0575-88623112 http://www.csctw.com.tw CHINA SEMICONDUCTOR CORPORATION Model No Spec. No. PS-LU-U30AHR4-A0R A Rev. ：CSPR-U30AHR4-A0R ■ Features - 1. High Current Operation 2. High Luminous Output 3. High Reliability and Solid Performance 4. Optimal Optical/Mechanical Design 5. Packaged in Tubes for Use with Automatic Pick and Place Equipment 6. Rohs Compliant ■ Device Selection Guide Chip LED Lens Part No. CSPR-U30AHR4-A0R Material Emitted Color AlInGaP Red Water Transparent ■ Package Outline Dimensions - ＊Tolerance：± 0.01 0.25 ：± Unit inch mm http://www.csctw.com.tw Page ： 1/5 CHINA SEMICONDUCTOR CORPORATION Model No Spec. No. PS-LU-U30AHR4-A0R A Rev. ：CSPR-U30AHR4-A0R ■ Absolute Maximum Rating - (Ta=25 Parameter Symbol Rating Unit Pd 196 mW Forward Current (DC) IF 70 mA Peak Forward Current * IFP 100 mA Reverse Voltage VR 5 V Operating Temp. Topr -30 ~ +80 Storage Temp. Tstg -40 ~ +100 Lead Soldering Temperature Tsol Power Dissipation * Pulse width ℃ ℃) ℃ ℃ Max. 260 for 5 sec Max. (3mm from the epoxy bulb) ≦0.1 msec. duty ≦1/10 ■ Electro-optical Characteristics - (Ta=25 Parameter Symbol Min. Typ. Max. Unit Forward Voltage VF ----- 2.3 2.8 V Luminous Intensity IV 6600 13000 ----- mcd Φv 6000 8000 ----- mlm Luminous Flux Dominant Wavelength Peak Wavelength Viewing Angle Reverse Current 2 ℃) Condition IF=70mA λd ----- 615 ------ nm λp ----- 625 ----- nm θ 1/2 ----- 60 ----- deg IR ----- ----- 100 μA http://www.csctw.com.tw VR=5V Page ： 2/5 CHINA SEMICONDUCTOR CORPORATION ■ Luminous Flux Rank Limits ( I Spec. No. PS-LU-U30AHR4-A0R A Rev. = 70mA ) F ： unit mlm Part No.CSPR-U30AHR4-A0R Code D E F G H min. 2000 2500 3000 3500 4000 ■ Dominant Wavelength Rank Limits ( I F max. 2500 3000 3500 4000 5000 = 70mA ) ：nm unit Part No. CSPR-U30AHR4-A0R Code min. max. A5 A6 R1 612 616 620 616 620 625 R2 625 630 ■ Forward Voltage Rank Limits ( I F = 70mA ) ： unit v Part No. CSPR-U30AHR4-A0R Code min. max. C 1.8 2.0 D 2.0 2.2 E 2.2 2.4 F 2.4 2.6 G 2.6 2.8 Notes: 1. 2. 3. 4. 5. 6. 7. ％ Tolerance of measurement of luminous Flux :±15 Tolerance of measurement of dominant wavelength :±2nm Tolerance of measurement of forward voltage :±0.05v All data are measured by CSC's test equipment. One delivery will include several color rank, VF rank and Iv ranks of the products. The quantity-ratio of the ranks is decided by CSC. Please confirm with CSC salesman,if your request different form standard specification. http://www.csctw.com.tw Page ： 3/5 CHINA SEMICONDUCTOR CORPORATION Model No Spec. No. PS-LU-U30AHR4-A0R A Rev. ：CSPR-U30AHR4-A0R ■ Typical Electrical / Optical Charateristics Curves - Relative Intensity @ 20mA (Ta = 25 ℃ Unless Otherwise Noted) 1.0 0.5 0 550 600 650 700 1 y t i s o n i m 0.5 u L e v i t a l e R 0------------ -- -------- ---Radiation Angle Wavelength (nm) Fig 5. Relative Intensity Vs. Wavelength Fig 6. Relative Luminous Intensity vs.Radiation Angle http://www.csctw.com.tw Page ： 4/5 CHINA SEMICONDUCTOR CORPORATION Model No Spec. No. PS-LU-U30AHR4-A0R A Rev. ：CSPR-U30AHR4-A0R ■ Precautions For Use - 1. Recommended Soldering conditions Wave Soldering Temperature(°C) 260(max.) 250 240 Preheat 105(max.) 0 5 sec. Max. 60sec. Time(sec.) 2. Soldering Iron Basic SPEC. is be shorter (+10 ≦5sec. When 260℃. If temperature is higher, time should ℃→ -1sec.). Power dissipation of iron should be smaller than 15W , and temperature should be controllable. Surface temperature of the device should be under 230 ℃. 3. Static Electricity a. Static electricity or surge voltage damages LEDs.. It is recommended that a wrist band or an anit-electrostatic glove be used when handling the LEDs. b. All devices, equipment and machinery must be properly grounded. It is recommended that mesures be taken against surge voltage to the equipment that mounts the LEDs. Note: The specifications are subject to change without notice. Please contact us for updated information. http://www.csctw.com.tw Page ： 5/5