DS92LX1621,DS92LX1622 DS92LX1621/DS92LX1622 10 - 50 MHz DC-Balanced Channel Link III Serializer and Deserializer with Bi-Directional Control Channel Literature Number: SNLS327G DS92LX1621/DS92LX1622 10 - 50 MHz DC-Balanced Channel Link III Serializer and Deserializer with Bi-Directional Control Channel General Description ■ Embedded clock with DC Balanced coding to support AC- The DS92LX1621 / DS92LX1622 chipset offers a Channel Link III interface with a high-speed forward channel and a fullduplex back channel for data transmission over a single differential pair. The Serializer/Deserializer pair is targeted for direct connections between automotive camera systems and Host Controller/Electronic Control Unit (ECU). The primary transport sends 16 bits of image data over a single high-speed serial stream together with a low latency bi-directional control channel transport that supports I2C. Included with the 16-bit payload is a selectable data integrity option for CRC (Cyclic Redundancy Check) or parity bit to monitor transmission link errors. Using National’s embedded clock technology allows transparent full-duplex communication over a single differential pair, carrying asymmetrical bi-directional control information without the dependency of video blanking intervals. This single serial stream simplifies transferring a wide data bus over PCB traces and cable by eliminating the skew problems between parallel data and clock paths. This significantly saves system cost by narrowing data paths that in turn reduce PCB layers, cable width, and connector size and pins. In addition, the Deserializer inputs provide equalization control to compensate for loss from the media over longer distances. Internal DC balanced encoding/decoding is used to support AC-Coupled interconnects. The sleep function provides a power-savings mode and a remote wake up interrupt for signaling of a remote device. The Serializer is offered in a 32-pin LLP package, and Deserializer is offered in a 40-pin LLP package. ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ coupled interconnects Capable to drive up to 10 meters shielded twisted-pair Bi-directional control interface channel with I2C support I2C interface for device configuration. Single-pin ID addressing 16–bit data payload with CRC (Cyclic Redundancy Check) for checking data integrity with programmable data transmission error detection and interrupt control Up to 6 Programmable GPIO's AT-SPEED BIST diagnosis feature to validate link integrity Individual power-down controls for both SER and DES User-selectable clock edge for parallel data on both SER and DES Integrated termination resistors 1.8V- or 3.3V-compatible parallel bus interface Single power supply at 1.8V IEC 61000–4–2 ESD compliant No reference clock required on Deserializer Programmable Receive Equalization LOCK output reporting pin to ensure link status EMI/EMC Mitigation — DES Programmable Spread Spectrum (SSCG) outputs — DES Receiver staggered outputs Temperature range −40°C to +85°C SER package: 32 pin LLP (5mm x 5mm) DES package: 40 pin LLP (6mm x 6mm) Features ■ ■ ■ ■ Configurable data throughput Applications — 12–bit (min) up to 600 Mbits/sec — 16–bit (def) up to 800 Mbits/sec — 18–bit (max) up to 900 Mbits/sec ■ 10 MHz to 50 MHz input clock support ■ Industrial Displays, Touch Screens ■ Medical Imaging Typical Application Diagram 30123027 FIGURE 1. Typical Application Circuit TRI-STATE® is a registered trademark of National Semiconductor Corporation. © 2011 National Semiconductor Corporation 301230 www.national.com DS92LX1621 / DS92LX1622 10 - 50 MHz DC-Balanced Channel Link III Serializer and Deserializer with Bi-Directional Control Channel July 12, 2011 DS92LX1621 / DS92LX1622 Block Diagrams 30123028 FIGURE 2. Block Diagram 30123029 FIGURE 3. Application Block Diagram Ordering Information NSID Package Description Quantity SPEC Package ID DS92LX1621SQE DS92LX1621SQ 32–pin LLP, 5.0 X 5.0 X 0.8 mm, 0.5 mm pitch 250 NOPB SQA32A 32–pin LLP, 5.0 X 5.0 X 0.8 mm, 0.5 mm pitch 1000 NOPB SQA32A DS92LX1621SQX 32–pin LLP, 5.0 X 5.0 X 0.8 mm, 0.5 mm pitch 4500 NOPB SQA32A DS92LX1622SQE 40–pin LLP, 6.0 X 6.0 X 0.8 mm, 0.5 mm pitch 250 NOPB SQA40A DS92LX1622SQ 40–pin LLP, 6.0 X 6.0 X 0.8 mm, 0.5 mm pitch 1000 NOPB SQA40A DS92LX1622SQX 40–pin LLP, 6.0 X 6.0 X 0.8 mm, 0.5 mm pitch 4500 NOPB SQA40A www.national.com 2 DS92LX1621 / DS92LX1622 DS92LX1621 Pin Diagram 30123019 Serializer - DS92LX1621 — Top View 3 www.national.com DS92LX1621 / DS92LX1622 DS92LX1621 Serializer Pin Descriptions Pin Name Pin No. I/O, Type Description LVCMOS PARALLEL INTERFACE DIN[13:0] 32, 31, 30, 29, 27, 26, 24, 23, 22, 21, 20, 19, 18, 17 Inputs, LVCMOS w/ Parallel data inputs. pull down HSYNC 1 Inputs, LVCMOS w/ Parallel data input 14, typically used as Horizontal SYNC Input pull down VSYNC 2 Inputs, LVCMOS w/ Parallel data input 15, typically used as Vertical SYNC Input pull down PCLK 3 Input, LVCMOS w/ pull down Pixel Clock Input Pin. Strobe edge set by TRFB control register. GENERAL PURPOSE INPUT OUTPUT (GPIO) DIN[3:0]/ GPIO[5:2] 20, 19, 18, 17 GPIO[1:0] 16, 15 Input/Output, Digital DIN[3:0] general-purpose pins can be individually configured as either inputs or outputs; used to control and respond to various commands. Input/Output, Digital General-purpose pins can be individually configured as either inputs or outputs; used to control and respond to various commands. SERIAL CONTROL BUS - I2C COMPATIBLE Clock line for the serial control bus communication SCL requires an external pull-up resistor to VDDIO. SCL 4 Input/Output, Digital SDA 5 Input/Output, Open Data line for the serial control bus communication SDA requires an external pull-up resistor to VDDIO. Drain M/S 8 CAD 6 Input, LVCMOS w/ pull down I2C Mode Select M/S = L, Master (default); device generates and drives the SCL clock line M/S = H, Slave; device accepts SCL clock input Input, analog Continuous Address Decoder Input pin to select the Slave Device Address. Input is connect to external resistor divider to programmable Device ID address (see Serial Control Bus Connection). CONTROL AND CONFIGURATION Power down Mode Input Pin. PDB = H, Transmitter is enabled and is ON. PDB = L, Transmitter is in Sleep (Power Down). When the transmitter is in the SLEEP state, the PLL is shutdown, and IDD is minimized. PDB 9 Input, LVCMOS w/ pull down RES 7 Input, LVCMOS w/ pull down Reserved. This pin MUST be tied LOW. Channel Link III INTERFACE DOUT+ 13 Input/Output, CML Non-inverting differential output, back-channel input. DOUT- 12 Input/Output, CML Inverting differential output, back-channel input. VDDPLL 10 Power, Analog PLL Power, 1.8V ±5% VDDT 11 Power, Analog Tx Analog Power, 1.8V ±5% VDDCML 14 Power, Analog LVDS & BC Dr Power, 1.8V ±5% VDDD 28 Power, Digital Digital Power, 1.8V ±5% 25 Power, Digital Power for input stage, The single-ended inputs are powered from VDDIO. DAP Ground, DAP DAP must be grounded. Connect to ground plane with at least 9 vias. Power and Ground VDDIO VSS www.national.com 4 DS92LX1621 / DS92LX1622 DS92LX1622 Pin Diagram 30123020 Deserializer - DS92LX1622 — Top View 5 www.national.com DS92LX1621 / DS92LX1622 DS92LX1622 Deserializer Pin Descriptions Pin Name Pin No. I/O, Type Description LVCMOS PARALLEL INTERFACE ROUT[13:0] 9, 10, 11, 12, 14, 15, 17, 18, 19, 20, 21, 22, 23, 24 Outputs, LVCMOS Parallel data outputs. HSYNC 7 Output, LVCMOS Parallel data output 14, typically used as Horizontal SYNC output VSYNC 6 Output, LVCMOS Parallel data output 14, typically used as Vertical SYNC output PCLK 5 Output, LVCMOS Pixel Clock Output Pin. Strobe edge set by RRFB control register General Purpose Input Output (GPIO) ROUT[3:0] / GPIO[5:2] 21, 22, 23, 24 Input/Output, Digital ROUT[3:0] general-purpose pins can be individually configured as either inputs or outputs; used to control and respond to various commands. 26, 27 Input/Output, Digital General-purpose pins can be individually configured as either inputs or outputs; used to control and respond to various commands. GPIO[1:0] SERIAL CONTROL BUS - I2C COMPATIBLE Clock line for the serial control bus communication SCL requires an external pull-up resistor to VDDIO. SCL 3 Input/Output, Digital SDA 2 Input/Output, Open Data line for serial control bus communication SDA requires an external pull-up resistor to VDDIO. Drain M/S 40 CAD Input, LVCMOS w/ pull up 1 Input, analog I2C Mode Select M/S = L, Master; device generates and drives the SCL clock line M/S = H, Slave (default); device accepts SCL clock input Continuous Address Decoder Input pin to select the Slave Device Address. Input is connect to external resistor divider to programmable Device ID address (see Serial Control Bus Connection) CONTROL AND CONFIGURATION PDB 29 LOCK PASS RES 28 31 Input, LVCMOS w/ pull down Power down Mode Input Pin. PDB = H, Receiver is enabled and is ON. PDB = L, Receiver is in Sleep (Power down mode). When the Receiver is in the SLEEP state, the LVCMOS Outputs are in TRI-STATE, the PLL is shutdown and IDD is minimized. Output, LVCMOS LOCK Status Output Pin. LOCK = H, PLL is Locked, outputs are active LOCK = L, PLL is unlocked, ROUT and PCLK output states are controlled by OSS_SEL. May be used as Link Status. Output, LVCMOS When BISTEN = L; Normal operation PASS is high to indicate no errors are detected. The PASS pin asserts low to indicate a CRC error was detected on the link. 32, 33, 39 - Reserved. Pin 39: This pin MUST be tied LOW. Pins 32, 33: Leave pin open. 37 Input, LVCMOS w/ pull down BIST Enable Pin. BISTEN = H, BIST Mode is enabled. BISTEN = L, BIST Mode is disabled. Output, LVCOMS PASS Output Pin for BIST mode. PASS = H, ERROR FREE Transmission PASS = L, one or more errors were detected in the received payload. Leave Open if unused. Route to test point (pad) recommended. BIST MODE BISTEN PASS 31 Channel Link III INTERFACE www.national.com 6 Pin No. I/O, Type Description RIN+ 35 Input/Output, CML Noninverting differential input, back channel output. RIN- 36 Input/Output, CML Inverting differential input, back channel output. POWER AND GROUND VDDSSCG VDDOR1/2/3 4 Digital Power SSCG Power, 1.8V ±5% Power supply must be connect regardless if SSCG function is in operation 25, 16, 8 Digital Power TTL Output Buffer Power, The single-ended outputs and control input are powered from VDDIO. VDDIO can be connected to a 1.8V ±5% or 3.3V ±10% VDDD 13 Digital Power Digital Core Power, 1.8V ±5% VDDR 30 Analog Power Rx Analog Power, 1.8V ±5% VDDCML 34 Analog Power Bi-Directional Control Channel Driver Power, 1.8V ±5% VDDPLL 38 Analog Power PLL Power, 1.8V ±5% DAP Ground VSS DAP must be grounded. Connect to the ground plane with at least 16 vias. 7 www.national.com DS92LX1621 / DS92LX1622 Pin Name DS92LX1621 / DS92LX1622 θJC(based on 16 thermal vias) ESD Rating (IEC 61000–4–2) Absolute Maximum Ratings (Note 1) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Supply Voltage ( VDD1V8) Supply Voltage (VDD3V3) LVCMOS Input Voltage (VDD1V8) LVCMOS Input Voltage (VDD3V3) LVCMOS Output Voltage (VDD) CML Driver I/O Voltage (VDD1V8) CML Receiver I/O Voltage (VDD1V8) Junction Temperature Storage Temperature Maximum Package Power Dissipation Capacity Package Derating: DS92LX1621 32L LLP 6.9 °C/W 1/θJA °C/W above +25° θJA(based on 16 thermal vias) 28.0 °C/W Serializer Electrical Characteristics Min 1.71 1.71 3 VDD (1.8V) VDDIO (1.8V Mode) VDDIO (3.3V Mode) Supply Noise VDDn(1.8V) VDDIO(1.8V) VDD3V3 Operating Free Air Temperature (TA) Input Clock Rate 1/θJA °C/W above +25° θJC (based on 9 thermal vias) Maximum Package Power Dissipation Capacity Package Package Derating: DS92LX1622 40L LLP ≥±25 kV ≥±10 kV ≥±8 kV Recommended Operating Conditions −0.3V to (VDD1V8 + 0.3V) +150°C −65°C to +150°C 34.3 °C/W RD = 330Ω, CS = 150pF Air Discharge (DOUT+, DOUT-, RIN+, RIN-) Contact Discharge (DOUT+, DOUT-, RIN+, RIN-) ESD Rating (HBM) −0.3V to +2.5V −0.3V to +4.0V −0.3V to +(VDD1V8 + 0.3V) −0.3V to +(VDD3V3 + 0.3V) −0.3V to +(VDD + 0.3V) −0.3V to (VDD1V8 + 0.3V) θJA (based on 9 thermal vias) 4.4 °C/W -40 Nom 1.8 1.8 3.3 25 10 Max 1.89 1.89 3.6 Units V V V 25 25 50 mVp-p mVp-p mVp-p 85 °C 50 MHz (Note 2, Note 3, Note 4) Over recommended operating supply and temperature ranges unless otherwise specified. Symbol Parameter Conditions Min Typ Max Units LVCMOS DC SPECIFICATIONS 3.3V I/O (SER INPUTS, DES OUTPUTS, GPIO, CONTROL INPUTS AND OUTPUTS) VIH High Level Input Voltage VIN = 3.0V to 3.6V 2.0 VIN V VIL Low Level Input Voltage VIN = 3.0V to 3.6V GND 0.8 V IIN Input Current VIN = 0V or 3.6V VIN = 3.0V to 3.6V -20 +20 µA VOH High Level Output Voltage VDDIO = 3.0V to 3.6V 2.4 VDDIO V VOL Low Level Output Voltage VDDIO = 3.0V to 3.6V IOH = +4mA GND 0.4 V IOS Output Short Circuit Current VOUT = 0V Serializer GPIO Outputs -24 mA Deserializer LVCMOS Outputs IOZ TRI-STATE® Output Current PDB = 0V, VOUT = 0V or VDD LVCMOS Outputs ±1 -39 -20 ±1 +20 µA LVCMOS DC SPECIFICATIONS 1.8V I/O (TX INPUTS, RX OUTPUTS, GPIO, CONTROL INPUTS AND OUTPUTS) VIH High Level Input Voltage VIN = 1.71V to 1.89V 0.65 VIN VIN +0.3 VIL Low Level Input Voltage VIN = 1.71V to 1.89V GND 0.35 VIN IIN Input Current VIN = 0V or 1.89V VIN = 1.71V to 1.89V -20 VOH High Level Output Voltage VDDIO = 1.71V to 1.89V IOH = −4mA VDDIO 0.45 VDDIO VOL Low Level Output Voltage VDDIO = 1.71V to 1.89V IOL = +4 mA GND 0.45 www.national.com 8 ±1 +20 V µA V V IOS IOZ Parameter Output Short Circuit Current Conditions VOUT = 0V (Note 10) TRI-STATE® Output Current PDB = 0V, VOUT = 0V or VDD Min Typ Serializer GPIO Outputs -11 Deserializer LVCMOS Outputs -20 LVCMOS Outputs Max Units mA -20 ±1 +20 µA 268 340 412 mV 1 50 mV CML DRIVER DC SPECIFICATIONS (DOUT+, DOUT-) |VOD| Output Differential Voltage RT = 100Ω ΔVOD Output Differential Voltage Unbalance RL = 100Ω VOS Output Differential Offset Voltage RL = 100Ω (Figure 7) ΔVOS Offset Voltage Unbalance RL = 100Ω IOS Output Short Circuit Current DOUT+/- = 0V, PDB = L or H (Note 10) RT Differential Internal Termination Resistance Differential across DOUT+ and DOUT- VDD (MIN) VDD (MAX) VDD - VOD VOD (MAX) VOD (MIN) V 1 mV 50 mA -27 80 100 120 Ω CML RECEIVER DC SPECIFICATIONS (RIN+, RIN-) VTH Differential Threshold High Voltage +90 Figure 8 mV VTL Differential Threshold Low Voltage VIN Differential Input Voltage Range IIN Input Current VIN = VDD or 0V, VDD = 1.89V -20 RT Differential Internal Termination Resistance Differential across RIN+ and RIN- 80 -90 RIN+ - RIN- 180 mV +20 µA 100 120 Ω 62 90 SER/DES SUPPLY CURRENT *DIGITAL, PLL, AND ANALOG VDDS IDDT IDDIOT IDDTZ IDDIOTZ Serializer (Tx) Total Supply Current Mode (includes load current) Serializer (Tx) VDDIO Supply Current (includes load current) RT = 100Ω WORST CASE pattern (Figure 5) RT = 100Ω RANDOM PRBS-7 pattern RT = 100Ω WORST CASE pattern () Serializer (Tx) Supply Current PDB = 0V; All other Power-down LVCMOS Inputs = 0V 9 VDDn = 1.89V, f = 50MHz Default Registers mA 55 VDDn = 1.89V, f = 50MHz Default Registers 2 VDDn = 3.6V, f = 50MHz Default Registers 7 15 VDD = 1.89V 370 775 VDDIO = 1.89V 55 125 VDDIO = 3.6V 65 135 5 mA µA www.national.com DS92LX1621 / DS92LX1622 Symbol DS92LX1621 / DS92LX1622 Symbol IDDR IDDIOR IDDRZ IDDIORZ Parameter Conditions Min Typ Max 96 VDDn = 1.89V CL = 8pF WORST CASE Pattern (Figure 5) f = 50 MHz SSCG[3:0] = ON Default Registers 60 VDDn = 3.6V CL = 8pF WORST CASE Pattern f = 50 MHz Default Registers 53 Deserializer (Rx) VDDIO VDDIO = 1.89V Supply Current (includes load CL = 8pF current) WORST CASE Pattern (Figure 5) f = 50 MHz Default Registers Deserializer (Rx) Supply Current (includes load current) Deserializer (Rx) Supply Current Power-down Units mA 16 25 VDDIO = 3.6V CL = 8pF Worst Case Pattern f = 50 MHz Default Registers 38 64 PDB = 0V; All other LVCMOS Inputs = 0V VDDn = 1.89V 42 400 VDDIO = 1.89V 8 40 VDDIO = 3.6V 350 800 µA Recommended Serializer Timing for PCLK Over recommended operating supply and temperature ranges unless otherwise specified. Symbol Parameter Min Typ Max Units 20 T 100 ns Transmit Clock Input High Time 0.4T 0.5T 0.6T ns tTCIL Transmit Clock Input Low Time 0.4T 0.5T 0.6T ns tCLKT PCLK Input Transition Time 3 ns fosc Internal oscillator clock source tTCP Transmit Clock Period tTCIH Conditions 10 MHz — 50 MHz 0.5 25 MHz Serializer Switching Characteristics Over recommended operating supply and temperature ranges unless otherwise specified. Symbol Parameter Conditions tLHT CML Low-to-High Transition Time RL = 100Ω (Figure 6) tHLT CML High-to-Low Transition Time RL = 100Ω (Figure 6) tDIS Data Input Setup to PCLK tDIH Data Input Hold from PCLK tPLD Serializer PLL Lock Time tSD Serializer Delay tJIND Serializer Output Deterministic Jitter www.national.com Serializer Data Inputs (Figure 10) Min Serializer output intrinsic deterministic jitter. Measure with PRBS-7 test pattern. PCLK = 50 MHz 10 Max Units 150 330 ps 150 330 ps 2.0 ns 2.0 ns RL = 100Ω ((Note 5, Note 9)) RT = 100Ω f = 10-50 MHz Reg Address 0x03h b[0] (TRFB = 1) (Figure 12) Typ 6.386T + 5 1 2 ms 6.386T + 12 6.386T + 19.7 ns 0.13 UI tJINR Parameter Serializer Output Random Jitter Conditions Min Typ Max Units Serializer output intrinsic random jitter (cycle-cycle). Alternating – 1,0 pattern. 0.04 UI 0.396 UI tJINT Peak-to-peak Serializer Output Jitter Serializer output peak-to-peak jitter includes deterministic jitter, random jitter, and jitter transfer from serializer input. Measure with PRBS-7 test pattern. λSTXBW Serializer Jitter Transfer Function -3 dB Bandwidth PCLK = 50 MHz Default Registers 1.9 MHz δSTX Serializer Jitter Transfer Function PCLK = 50 MHz Default Registers 0.944 dB δSTXf Serializer Jitter Transfer Function Peaking Frequency PCLK = 50 MHz Default Registers 500 kHz Deserializer Switching Characteristics Over recommended operating supply and temperature ranges unless otherwise specified. Symbol Parameter Conditions Pin/Freq. tRCP Receiver Output Clock Period tRCP = tTCP PCLK tPDC PCLK Duty Cycle Default Registers SSCG[3:0] = OFF PCLK tCLH LVCMOS Low-to-High Transition VDDIO: 1.71V to 1.89V or PCLK Time 3.0V to 3.6V, CL = 8 pF LVCMOS High-to-Low Transition (lumped load) Default Registers Time ( (Note 10)) tCHL tCLH tCHL LVCMOS Low-to-High Transition VDDIO: 1.71V to 1.89V or Time 3.0V to 3.6V, CL = 8 pF Deserializer Data (lumped load) Outputs LVCMOS High-to-Low Transition Default Registers Time ( ) (Note 9) tROS ROUT Setup Data to PCLK tROH ROUT Hold Data to PCLK tDD Deserializer Delay tDDLT Deserializer Data Lock Time tRJIT Receiver Input Jitter Tolerance VDDIO: 1.71V to 1.89V or 3.0V to 3.6V, CL = 8pF Deserializer Data (lumped load) Outputs Default Registers () Default Registers Register 0x03h b[0] (RRFB = 1) 10 MHz-50 MHz Min Typ Max Units 20 T 100 ns 45 50 55 % 1.3 2.0 2.8 1.3 2.0 2.8 1.6 2.4 3.3 1.6 2.4 3.3 0.38T 0.5T 0.38T 0.5T ns ns ns 4.571T + 4.571T + 4.571T 8 12 + 16 10 MHz-50 MHz 10 50 MHz 0.53 10 MHz 300 550 50 MHz 120 250 ns ms UI tRDJ Receiver Clock Jitter PCLK SSCG[3:0] = OFF tDPJ Deserializer Period Jitter PCLK SSCG[3:0] = OFF 10 MHz 425 600 50 MHz 320 480 tDCCJ Deserializer Cycle-to-Cycle Clock PCLK SSCG[3:0] = OFF Jitter 10 MHz 320 500 50 MHz 300 500 fdev Spread Spectrum Clocking Deviation Frequency 20 MHz-50 MHz ±0.5% to ±2.0% % fmod Spread Spectrum Clocking Modulation Frequency 20 MHz-50 MHz ±9 kHz to ±66 kHz kHz LVCMOS Output Bus (Figure 17) 11 ps ps ps www.national.com DS92LX1621 / DS92LX1622 Symbol DS92LX1621 / DS92LX1622 Bi-Directional Control Bus Timing Specifications (SCL, SDA) - (Figure 4) Over recommended operating supply and temperature ranges unless otherwise specified. Symbol Parameter Conditions Min Typ Max Units RECOMMENDED INPUT TIMING REQUIREMENTSRECOMMENDED INPUT TIMING REQUIREMENTS ((Note 13)) fSCL SCL Clock Frequency fLOW SCL Low Period fHIGH >0 fSCL = 100 kHz 100 kHz 4.7 µs SCL High Period 4.0 µs tHD:STA Hold time for a start or a repeated start condition 4.0 µs tSU:STA Set Up time for a start or a repeated start condition 4.7 µs tHD:DAT Data Hold Time tSU:DAT Data Set Up Time 250 tSU:STO Set Up Time for STOP Condition, 4.0 tr SCL & SDA Rise Time 1000 tf SCL & SDA Fall Time 300 ns Cb Capacitive load for bus 400 pF 0 3.45 µs ns µs ns SWITCHING CHARACTERISTICS ((Note 9)) fSCL fLOW SCL Clock Frequency SCL Low Period Serializer M/S = 0 – R/W Register 0x05 = 0x40'h 100 Deserializer M/S = 0 – READ Register 0x06 b[6:4] = 0x00'h 100 Serializer M/S = 0 – R/W Register 0x05 = 0x40'h Deserializer M/S = 0 – READ Register 0x06 b[6:4] = 0x00'h Serializer M/S = 0 – R/W Register 0x05 = 0x40'h kHz 4.7 μs 4.0 μs fHIGH SCL High Period tHD:STA Hold time for a start or a repeated start Serializer M/S = 0 Register 0x05 = condition 0x40'h 4.0 μs tSU:STA Set Up time for a start or a repeated start condition 4.7 μs tHD:DAT Data Hold Time tSU:DAT Data Set Up Time tSU:STO Set Up Time for STOP Condition tf SCL & SDA Fall Time tBUF Bus free time between a stop and start Serializer M/S = 0 condition tTIMEOUT NACK Time out www.national.com Deserializer M/S = 0 – READ Register 0x06 b[6:4] = 0x00'h Serializer M/S = 0 Register 0x05 = 0x40'h 0 3.45 250 Serializer M/S = 0 μs 4.0 300 ns μs 4.7 Serializer M/S = 1 1 Deserializer MODE = 1 Register 0x06 b[2:0]=111'b 25 12 μs ns ms DS92LX1621 / DS92LX1622 30123036 FIGURE 4. Bi-Directional Control Bus Timing Bi-Directional Control Bus DC Characteristics (SCL, SDA) - I2C Compliant Symbol Parameter Conditions Max Units 0.7 x VDDIO Min Typ VDDIO V GND 0.3 x VDDIO V VIH Input High Level SDA and SCL VIL Input Low Level Voltage SDA and SCL VHY Input Hysteresis IOZ TRI-STATE® Output Current PDB = 0V VOUT = 0V or VDD -20 ±1 +20 µA IIN Input Current SDA or SCL, Vin = VDDIO or GND -20 ±1 +20 µA CIN Input Pin Capacitance VOL Low Level Output Voltage >50 mV <5 pF SCL and SDA VDDIO = 3.0V IOL = 1.5 mA 0.36 SCL and SDA VDDIO = 1.71V IOL = 1 mA 0.36 V Note 1: “Absolute Maximum Ratings” indicate limits beyond which damage to the device may occur, including inoperability and degradation of device reliability and/or performance. Functional operation of the device and/or non-degradation at the Absolute Maximum Ratings or other conditions beyond those indicated in the Recommended Operating Conditions is not implied. The Recommended Operating Conditions indicate conditions at which the device is functional; the device should not be operated beyond such conditions. Note 2: The Electrical Characteristics tables list guaranteed specifications under the listed Recommended Operating Conditions except as otherwise modified or specified by the Electrical Characteristics Conditions and/or Notes. Typical specifications are estimations only and are not guaranteed. Note 3: Current into device pins is defined as positive. Current out of a device pin is defined as negative. Voltages are referenced to ground except VOD, ΔVOD, VTH and VTL which are differential voltages. Note 4: Typical values represent most likely parametric norms at 1.8V or 3.3V, TA = +25°C, and at the Recommended Operation Conditions at the time of product characterization and are not guaranteed. Note 5: tPLD and tDDLT is the time required by the serializer and deserializer to obtain data lock when exiting power-down state with an active PCLK. Note 6: tDCJ is the maximum amount of jitter measured over 30,000 samples based on Time Interval Error (TIE). Note 7: tDPJ is the maximum amount the period is allowed to deviate measured over 30,000 samples. Note 8: tDCCJ is the maximum amount of jitter between adjacent clock cycles measured over 30,000 samples. Note 9: Specification is guaranteed by design and is not tested in production. Note 10: Specification is guaranteed by characterization and is not tested in production. Note 11: tRJIT max (0.61 UI) is limited by instrumentation and actual tRJIT of in-band jitter at low frequency (<2MHz) is greater than 1 UI. Note 12: UI – Unit Interval is equivalent to one ideal serialized data bit width. The UI scales with PCLK frequency. Note 13: Recommended Input Timing Requirements are input specifications and not tested in production. 13 www.national.com DS92LX1621 / DS92LX1622 AC Timing Diagrams and Test Circuits 30123052 FIGURE 5. “Worst Case” Test Pattern 30123046 30123047 FIGURE 6. Serializer CML Output Load and Transition Times www.national.com 14 DS92LX1621 / DS92LX1622 30123048 30123030 FIGURE 7. Serializer VOD DC Diagram 30123034 FIGURE 8. Differential VTH/VTL Definition Diagram 30123016 FIGURE 9. Serializer Input Clock Transition Times 15 www.national.com DS92LX1621 / DS92LX1622 30123049 FIGURE 10. Serializer Setup/Hold Times 30123032 FIGURE 11. Serializer Data Lock Time 30123050 FIGURE 12. Serializer Delay 30123013 FIGURE 13. Deserializer Data Lock Time www.national.com 16 DS92LX1621 / DS92LX1622 30123014 FIGURE 14. Deserializer LVCMOS Output Load and Transition Times 30123011 FIGURE 15. Deserializer Delay 30123031 FIGURE 16. Deserializer Output Setup/Hold Times 30123035 FIGURE 17. Spread Spectrum Clock Output Profile 17 www.national.com DS92LX1621 / DS92LX1622 30123062 FIGURE 18. Typical Serializer Jitter Transfer Function at 43 MHz 30123059 FIGURE 19. Typical Deserializer Input Jitter Tolerance Curve at 43 MHz www.national.com 18 Addr (Hex) 0 Name Bits Field R/W Default 7:1 DEVICE ID RW 0x58 SER ID RW 0 0: Device ID is from CAD 1: Register I2C Device ID overrides CAD 0 Reserved 0 Standby mode control. Retains control register data. Supported only when M/S = 0 0: Enabled. Low-current Standby mode with wake-up capability. Suspends all clocks and functions. 1: Disabled. Standby and wake-up disabled I2C Device ID 0 7:3 1 2 Reserved STANDBY RW 1 DIGITAL RESET0 RW 1: Resets the device to default register values. Does not 0 self clear affect device I2C Bus or Device ID 0 DIGITAL RESET1 RW 0 1: Digital Reset, retains all register values self clear 7:0 7 RESERVED RX CRC CHECKER ENABLE 0x20'h RW Reserved 1 Back Channel CRC Enable 0: Disable 1: Enable For propper CRC operation, control register 0x03h b[6] of the Deserializer must be enabled. CRC Fault Tolerant Transmission 6 TX CRC GEN ENABLE RW 1 Forward Channel CRC Enable 0: Disable 1: Enable For propper CRC operation, control register 0x03h b[7] of the Deserializer must be enabled. VDDIO Control 5 VDDIO CONTOL RW 1 Auto VDDIO detect 0: Disable 1: Enable (auto detect mode) VDDIO Mode 4 VDDIO MODE RW 1 VDDIO voltage set Only used when VDDIOCONTROL = 0 0: 1.8V 1: 3.3V I2C PassThrough 3 I2C PASSTHROUGH RW 1 I2C Pass-Through Mode 0: Disabled 1: Enabled Reserved 2 RESERVED 0 Reserved 1 Switch over to internal 25 MHz oscillator clock in the absence of PCLK 0: Disable 1: Enable 1 Pixel Clock Edge Select: 0: Parallel Interface Data is strobed on the Falling Clock Edge. 1: Parallel Interface Data is strobed on the Rising Clock Edge. 0 Reserved 0 1: CRC Reset. Clears CRC Error counter. PCLK_AUTO TRFB 4 7-bit address of Serializer; 0x58h (1011_000X) default 2 Reset CRC Fault Tolerant Transmission 3 RESERVED Description CRC Transmission 1 0 PCLK_AUTO TRFB 7:6 RESERVED 5 CRC RESET 4:0 RESERVED RW RW RW Reserved 19 www.national.com DS92LX1621 / DS92LX1622 TABLE 1. DS92LX1621 Control Registers DS92LX1621 / DS92LX1622 Addr (Hex) Name 5 I2C Bus Rate 6 DES ID Bits R/W Default Description 7:0 I2C BUS RATE RW 0x40 I2C ratio is determined by the following: fSCL = 6.25 MHz / register value (in decimal) 0x40'h = ~100 kHz SCL (default) Note: Register values <0x32'h are NOT supported. 7:1 DES DEV ID RW 0x60 Deserializer Device ID = 0x60 (1100_000X) default 0 RESERVED 7:1 7 Field SLAVE DEV ID RW 0 Reserved. 0 Slave Device ID. Must be programmed to communicate with remote slave device 0 Reserved. Slave ID 0 RESERVED 8 Reserved 7:0 RESERVED RW 0 Reserved 9 Reserved 7:0 RESERVED RW 1 Reserved A CRC Errors 7:0 CRC ERROR B0 R 0 Number of CRC errors - 8 LSBs B CRC Errors 7:0 CRC ERROR B1 R 0 Number of CRC errors - 8 MSBs Reserved 7:3 RESERVED 0 Reserved PCLK Detect 2 PCLK DETECT R 0 1: Valid PCLK detected 0: Valid PCLK not detected CRC Check 1 DES ERROR R 0 1: CRC error during communication with Deserializer Cable Link Detect Status 0 LINK DETECT R 0 1: Cable link detected 0: Cable link not detected C D E F 10 11 GPIO[0] Config GPIO[1] Config GPIO[2] Config GPIO[3] Config GPIO[4] Config www.national.com 7:4 RESERVED 1 Reserved 3:2 RESERVED 0 Reserved 1 GPIO0 DIR RW 0 0: Output 1: Input 0 GPIO0 EN RW 1 0: TRI-STATE® 1: Enabled 7:4 RESERVED 0 Reserved 3:2 RESERVED 0 Reserved 1 GPIO1 DIR RW 0 0: Output 1: Input 0 GPIO1 EN RW 1 0: TRI-STATE® 1: Enabled 7:4 RESERVED 0 Reserved 3:2 RESERVED 0 Reserved 1 GPIO2 DIR RW 1 0: Output 1: Input 0 GPIO2 EN RW 1 0: TRI-STATE® 1: Enabled 7:4 RESERVED 0 Reserved 3:2 RESERVED 0 Reserved 1 GPIO3 DIR RW 1 0: Output 1: Input 0 GPIO3 EN RW 1 0: TRI-STATE® 1: Enabled 7:4 RESERVED 0 Reserved 3:2 RESERVED 0 Reserved 1 GPIO4 DIR RW 1 0: Output 1: Input 0 GPIO4 EN RW 1 0: TRI-STATE® 1: Enabled 20 12 13 Name GPIO[5] Config General Purpose Control Reg Bits Field 7:4 RESERVED 0 Reserved 3:2 RESERVED 0 Reserved 1 GPIO5 DIR RW 1 0: Output 1: Input 0 GPIO5 EN RW 1 0: TRI-STATE® 1: Enabled 7:0 GPCR[7] GPCR[6] GPCR[5] GPCR[4] GPCR[3] GPCR[2] GPCR[1] GPCR[0] R/W Default DS92LX1621 / DS92LX1622 Addr (Hex) Description 0: LOW 1: HIGH RW 0 21 www.national.com DS92LX1621 / DS92LX1622 TABLE 2. DS92LX1622 Control Registers Addr (Hex) 0 Name Bits Field R/W Default 7:1 DEVICE ID RW 0x60h DES ID RW 0 I2C Device ID 0 7:3 1 Description 7-bit address of Deserializer; 0x60h (1100_000X) default 0: Device ID is from CAD 1: Register I2C Device ID overrides CAD RESERVED Reserved 2 REM_WAKEUP RW 0 Remote Wake-up Select 1: Enable. Generate remote wakeup signal automatically wake-up the Serializer in Standby mode 0: Disable. Puts the Serializer (M/S = 0) in Standby mode when Deserializer M/S = 1 1 DIGITALRESET0 RW 0 self clear 1: Resets the device to default register values. Does not affect device I2C Bus or Device ID 0 DIGITALRESET1 RW 0 self clear 1: Digital Reset, retains all register values Reset Reserved 7:6 Reserved Auto Clock 5 AUTO_CLOCK RW 0 1: Output PCLK or Internal 25 MHz Oscillator clock 0: Only PCLK when valid PCLK present OSS Select 4 OSS_SEL RW 0 Output Sleep State Select 0: Outputs = LOW , when LOCK = L 1: Outputs = TRI-STATE®, when LOCK = L 0 SSCG Select 0000: Normal Operation, SSCG OFF 0001: fmod (KHz) PCLK/2168, fdev ±0.50% 0010: fmod (KHz) PCLK/2168, fdev ±1.00% 0011: fmod (KHz) PCLK/2168, fdev ±1.50% 0100: fmod (KHz) PCLK/2168, fdev ±2.00% 0101: fmod (KHz) PCLK/1300, fdev ±0.50% 0110: fmod (KHz) PCLK/1300, fdev ±1.00% 0111: fmod (KHz) PCLK/1300, fdev ±1.50% 1000: fmod (KHz) PCLK/1300, fdev ±2.00% 1001: fmod (KHz) PCLK/868, fdev ±0.50% 1010: fmod (KHz) PCLK/868, fdev ±1.00% 1011: fmod (KHz) PCLK/868, fdev ±1.50% 1100: fmod (KHz) PCLK/868, fdev ±2.00% 1101: fmod (KHz) PCLK/650, fdev ±0.50% 1110: fmod (KHz) PCLK/650, fdev ±1.00% 1111: fmod (KHz) PCLK/650, fdev +/-1.50% 2 SSCG www.national.com 3:0 SSCG 22 Name Bits 7 Tx CRC CHECK ENABLE 6 Rx CRC GEN ENABLE 5 VDDIO CONTROL CRC Fault Tolerant Transmission VDDIO Control 3 R/W Default 1 Back Channel CRC Enable 0: Disable 1: Enable For proper CRC operation, on Serailizer 0x03h b[6] control register must be Enabled. RW 1 Foward Channel CRC Enable 0: Disable 1: Enable For proper CRC operation, on Serailizer 0x03h b[7] control register must be Enabled. RW 1 Auto voltage control 0: Disable 1: Enable (auto detect mode) RW VDDIO Mode 4 VDDIO MODE RW 0 I2C Pass-Through 3 I2C PASSTHROUGH RW 1 I2C Pass-Through Mode 0: Disabled 1: Enabled Auto ACK 2 AUTO ACK RW 0 0: Disable 1: Enable CRC Reset 1 CRC RESET RW 0 1: CRC reset 1 Pixel Clock Edge Select 0: Parallel Interface Data is strobed on the Falling Clock Edge 1: Parallel Interface Data is strobed on the Rising Clock Edge. 0 00'h: ~0.0 dB 01'h: ~4.5 dB 03'h: ~6.5 dB 07'h: ~7.5 dB 0F'h: ~8.0 dB 1F'h: ~11.0 dB 3F'h: ~12.5 dB FF'h: ~14.0 dB 0 Reserved 0 RRFB RW EQ Feature Control1 5 Description VDDIO voltage set Only used when VDDIOCONTROL = 0 0: 1.8V 1: 3.3V RRFB 4 Field Reserved 7:0 EQ 7:0 RESERVED RW 23 www.national.com DS92LX1621 / DS92LX1622 Addr (Hex) DS92LX1621 / DS92LX1622 Addr (Hex) Name Bits Reserved 7 SCL Prescale 6 Remote NACK Remote NACK 7 8 9 SER ID ID[0] Index ID[1] Index A ID[2] Index B ID[3] Index C D E ID[4] Index ID[5] Index ID[6] Index F ID[7] Index 10 ID[0] Match 11 12 13 14 ID[1] Match ID[2] Match ID[3] Match ID[4] Match www.national.com 6:4 3 Field R/W Default Description RESERVED SCL_PRESCALE REM_NACK_TIM ER RW 0 Prescales the SCL clock line when reading data byte from a slave device (M/S = 0) 000 : ~100 kHz SCL (default) 001 : ~125 kHz SCL 101 : ~11 kHz SCL 110 : ~33 kHz SCL 111 : ~50 kHz SCL Other values are NOT supported. 1 Remote NACK Timer Enable In slave mode (MODE = 1) if bit is set the I2C core will automatically timeout when no acknowledge condition was detected. 1: Enable 0: Disable 2:0 NACK_TIMEOUT RW 111'b Remote NACK Timeout. 000: 2.0 ms 001: 5.2 ms 010: 8.6 ms 011: 11.8 ms 100: 14.4 ms 101: 18.4 ms 110: 21.6 ms 111: 25.0 ms 7:1 SER DEV ID RW 0x58h Serializer Device ID = 0x58 (1011_000X) default 0 RESERVED 7:1 ID[0] INDEX 0 RESERVED 7:1 ID[1] INDEX 0 RESERVED 7:1 ID[2] INDEX 0 RESERVED 7:1 ID[3] INDEX 0 RESERVED 7:1 ID[4] INDEX 0 RESERVED 7:1 ID[5] INDEX 0 RESERVED 7:1 ID[6] INDEX 0 RESERVED 7:1 ID[7] INDEX 0 RESERVED 7:1 ID[0] MATCH 0 RESERVED 7:1 ID[1] MATCH 0 RESERVED 7:1 ID[2] MATCH 0 RESERVED 7:1 ID[3] MATCH 0 RESERVED 7:1 ID[4] MATCH 0 RESERVED RW RW RW RW RW RW RW RW RW RW RW RW RW 24 0 Reserved 0 Target slave Device ID slv_id1 [7:1] 0 Reserved. 0 Target slave Device ID slv_id1 [7:1] 0 Reserved. 0 Target slave Device ID slv_id2 [7:1] 0 Reserved. 0 Target slave Device ID slv_id3 [7:1] 0 Reserved. 0 Target slave Device ID slv_id4 [7:1] 0 Reserved. 0 Target slave Device ID slv_id5 [7:1] 0 Reserved. 0 Target slave Device ID slv_id6 [7:1] 0 Reserved. 0 Target slave Device ID slv_id7 [7:1] 0 Reserved. 0 Alias to match Device ID slv_id0 [7:1] 0 Reserved. 0 Alias to match Device ID slv_id1 [7:1] 0 Reserved. 0 Alias to match Device ID slv_id2 [7:1] 0 Reserved. 0 Alias to match Device ID slv_id3 [7:1] 0 Reserved. 0 Alias to match Device ID slv_id4 [7:1] 0 Reserved. Name 15 ID[5] Match Bits Field R/W Default RW 0 Alias to match Device ID slv_id5 [7:1] 0 Description Reserved 0 Alias to match Device ID slv_id6 [7:1] 0 Reserved. 7:1 ID[5] MATCH 0 RESERVED 7:1 ID[6] MATCH 0 RESERVED 7:1 ID[7] MATCH 0 Alias to match Device ID slv_id7 [7:1] 0 RESERVED 0 Reserved. 0 Reserved 16 ID[6] Match 17 ID[7] Match 18 Reserved 7:0 RESERVED RW RW 19 Reserved 7:0 RESERVED 1 Reserved 1A CRC Errors 7:0 CRC ERROR B0 R 0 Number of CRC errors 8 LSBs 1B CRC Errors 7:0 CRC ERROR B1 R 0 Number of CRC errors 8 MSBs Reserved 7:3 RESERVED CRC Check 2 SER ERROR Signal Detect Status LOCK Pin Status 1C 1D 1E 1F 20 GPIO[0] Config GPIO[1] Config GPIO[2] Config GPIO[3] Config 0x02'h DS92LX1621 / DS92LX1622 Addr (Hex) Reserved R 0 CRC error during communication with Serializer on Forward Channel 1 R 0 0: Active signal not detected 1: Active signal detected 0 R 0 0: CDR/PLL Unlocked 1: CDR/PLL Locked 7:3 RESERVED RW 0 Reserved. 2 GPIO0 SET RW 1 1: Configured as GPIO 0: Configured as ROUT data (OSS_SEL controlled) 1 GPIO0 DIR RW 1 0: Output 1: Input 0 GPIO0 EN RW 1 0: TRI-STATE® 1: Enabled 7:3 RESERVED RW 0 Reserved. 2 GPIO1 SET RW 1 1: Configured as GPIO 0: Configured as ROUT data (OSS_SEL controlled) 1 GPIO1 DIR RW 1 0: Output 1: Input 0 GPIO1 EN RW 1 0: TRI-STATE® 1: Enabled 7:3 RESERVED RW 0 Reserved 2 GPIO2 SET RW 0 1: Configured as GPIO 0: Configured as ROUT0 data (OSS_SEL controlled) 1 GPIO2 DIR RW 0 0: Output 1: Input 0 GPIO2 EN RW 1 0: TRI-STATE® 1: Enabled 7:3 RESERVED RW 0 Reserved 2 GPIO3 SET RW 0 1: Configured as GPIO 0: Configured as ROUT1 data (OSS_SEL controlled) 1 GPIO3 DIR RW 0 0: Output 1: Input 0 GPIO3 EN RW 1 0: Tri-state 1: Enabled 25 www.national.com DS92LX1621 / DS92LX1622 Addr (Hex) 21 22 Name GPIO[4] Config GPIO[5] Config Bits Field R/W Default Description 7:3 RESERVED RW 0 Reserved 2 GPIO4 SET RW 0 1: Configured as GPIO 0: Configured as ROUT2 data (OSS_SEL controlled) 1 GPIO4 DIR RW 0 0: Output 1: Input 0 GPIO4 EN RW 1 0: TRI-STATE® 1: Enabled 7:3 RESERVED RW 0 Reserved 2 GPIO5 SET RW 0 1: Configured as GPIO 0: Configured as ROUT3 data (OSS_SEL controlled) 1 GPIO5 DIR RW 0 0: Output 1: Input 0 GPIO5 EN RW 1 0: TRI-STATE® 1: Enabled 23 General Purpose Control Reg 7:00 GPCR[7] GPCR[6] GPCR[5] GPCR[4] GPCR[3] GPCR[2] GPCR[1] GPCR[0] 24 BIST 0 BIST_EN 25 BIST_ERR 7:0 BIST_ERR 26 Remote Wake Enable 7:6 REM_WAKEUP_ EN RW 0 11: Enable remote wake up mode 00: Normal operation mode Other values are NOT supported. 5:0 RESERVED RW 0 Reserved www.national.com 0: LOW 1: HIGH RW 0 RW 0 BIST Enable 0: Normal operation 1: Bist Enable R 0 Bist Error Counter 26 The DS92LX1621 / DS92LX1622 Channel Link III chipset is intended for camera applications. The Serializer/ Deserializer chipset operates from a 10 MHz to 50 MHz pixel clock frequency. The DS92LX1621 transforms a 16-bit wide parallel LVCMOS data bus along with a bi-directional control bus into a single high-speed differential pair. The high speed serial bit stream contains an embedded clock and DC-balance information which enhances signal quality to support AC coupling. The DS92LX1622 receives the single serial data stream and converts it back into a 16-bit wide parallel data bus together with the bi-directional control bus. The bi-directional channel function of the DS92LX1621 / DS92LX1622 provides bi-directional communication between SERIAL FRAME FORMAT The DS92LX1621 / DS92LX1622 chipset will transmit and receive a pixel of data in the following format: 30123061 FIGURE 20. Serial Bitstream for 28-bit Symbol The High Speed Forward Channel (HS_FC) is a 28-bit symbol composed of 16 bits of data containing camera data & control information transmitted from Serializer to Deserializer. CLK1 and CLK0 represent the embedded clock in the serial stream. CLK1 is always HIGH and CLK0 is always LOW. This data payload is optimized for signal transmission over an AC coupled link. Data is randomized, balanced and scrambled. The data payload may be checked using a 4-bit CRC function. The CRC monitors the link integrity of the serialized data and reports when an error condition is detected. The bi-directional control data is transferred over the single serial link along with the high-speed forward data. This architecture provides a full duplex low speed forward and backward path across the serial link together with a high speed forward channel without the dependence of the video blanking phase. of the clock (SCL) and data (SDA) signals. Pull-up resistors or current sources are required on the SCL and SDA busses to pull them high when they are not being driven low. A logic zero is transmitted by driving the output low. A logic high is transmitted by releasing the output and allowing it to be pulled-up externally. The appropriate pull-up resistor values will depend upon the total bus capacitance and operating speed. The DS92LX1621 / DS92LX1622 I2C bus data rate supports up to 100 kbps according to I2C specification. To start any data transfer, the DS92LX1621 / DS92LX1622 must be configured in the proper I2C mode. Each device can function as an I2C slave proxy or master proxy depending on the mode determined by M/S pin. The Ser/Des interface acts as a virtual bridge between Master controller (MCU) and the remote device. When the M/S pin is set to HIGH, the device is treated as a slave proxy; acts as a slave on behalf of the remote slave. When addressing a remote peripheral or Serializer/ Deserializer (not wired directly to the MCU), the slave proxy will forward any byte transactions sent by the Master controller to the target device. When M/S pin is set to LOW, the device will function as a master proxy device; acts as a master on behalf of the I2C master controller. Note that the devices must have complementary settings for the M/S configuration. For example, if the Serializer M/S pin is set to HIGH then the Deserializer M/S pin must be set to LOW and viceversa. DESCRIPTION OF BI-DIRECTIONAL CONTROL BUS AND I2C MODES The I2C compatible interface allows programming of the DS92LX1621, DS92LX1622, or an external remote device (such as a camera) through the bi-directional control channel. Register programming transactions to/from the DS92LX1621 / DS92LX1622 chipset are employed through the clock (SCL) and data (SDA) lines. These two signals have open drain I/Os and both lines must be pulled-up to VDDIO by external resistor. Figure 4 shows the timing relationships 30123060 FIGURE 21. Write Byte 27 www.national.com DS92LX1621 / DS92LX1622 the image sensor and the host device (FPGA, frame grabber, display, etc.). The integrated back channel transfers data bidirectionally over the same differential pair used for video data interface. This interface offers advantages over other chipsets by eliminating the need for additional wires for programming and control. The bi-directional control channel is controlled via an I2C port. The bi-directional control channel offers asynchronous communication and is not dependent on video blanking intervals. Functional Description DS92LX1621 / DS92LX1622 30123010 FIGURE 22. Read Byte 30123041 FIGURE 23. Basic Operation 30123042 FIGURE 24. START and STOP Conditions SLAVE CLOCK STRETCHING In order to communicate and synchronize with remote devices on the I2C bus through the bi-directional control channel, slave clock stretching must be supported by the I2C master controller/MCU. The chipset utilizes bus clock stretching (holding the SCL line low) during data transmission; where the I2C slave pulls the SCL line low prior to the 9th clock of every I2C data transfer (before the ACK signal). The slave device will not control the clock and only stretches it until the remote peripheral has responded; which is typically in the order of 12 μs (typical). www.national.com CAD PIN ADDRESS DECODER The CAD pin is used to decode and set the physical slave address of the Serializer/Deserializer (I2C only) to allow up to six devices on the bus using only a single pin. The pin sets one of six possible addresses for each Serializer/Deserializer device. The pin must be pulled to VDD (1.8V, NOT VDDIO)) with a 10 kΩ resistor and a pull down resistor (RID) of the recommended value to set the physical device address. The recommended maximum resistor tolerance is 0.1% worst case (0.2% total tolerance). 28 DS92LX1621 / DS92LX1622 30123043 FIGURE 25. Serial Control Bus Connection CAD Resistor Value - DS92LX1621 Ser Resistor RID Ω (±0.1%) Address 7'b Address 8'b 0 appended (WRITE) 0 GND 7b' 101 1000 (h'58) 8b' 1011 0000 (h'B0) 2.0k 7b' 101 1001 (h'59) 8b' 1011 0010 (h'B2) 4.7k 7b' 101 1010 (h'5A) 8b' 1011 0100 (h'B4) 8.2k 7b' 101 1011 (h'5B) 8b' 1011 0110 (h'B6) 12.1k 7b' 101 1100 (h'5C) 8b' 1011 1000 (h'B8) 39.0k 7b' 101 1110 (h'5E) 8b' 1011 1100 (h'BC) Resistor RID Ω (±0.1%) Address 7'b Address 8'b 0 appended (WRITE) 0 GND 7b' 110 0000 (h'60) 8b' 1100 0000 (h'C0) 2.0k 7b' 110 0001 (h'61) 8b' 1100 0010 (h'C2) 4.7k 7b' 110 0010 (h'62) 8b' 1100 0100 (h'C4) 8.2k 7b' 110 0011 (h'63) 8b' 1101 0110 (h'C6) 12.1k 7b' 110 0100 (h'64) 8b' 1101 1000 (h'C8) 39.0k 7b' 110 0110 (h'66) 8b' 1100 1100 (h'CC) CAD Resistor Value - DS92LX1622 Des ter 0x07h sets the Serializer device address and SLAVE_x_MATCH/SLAVE_x_INDEX registers 0x08h~0x17h set the remote target slave addresses. In slave mode the address register is compared with the address byte sent by the I2C master. If the addresses are equal to any of registers values, the I2C slave will acknowledge and hold the bus to propagate the transaction to the target device otherwise it returns no acknowledge. CAMERA MODE OPERATION In Camera mode, I2C transactions originate from the Master controller at the Deserializer side. The I2C slave core in the Deserializer will detect if a transaction is intended for the Serializer or a slave at the Serializer. Commands are sent over the bi-directional control channel to initiate the transactions. The Serializer will receive the command and generate an I2C transaction on its local I2C bus. At the same time, the Serializer will capture the response on the I2C bus and return the response on the forward channel link. The Deserializer parses the response and passes the appropriate response to the Deserializer I2C bus. To configure the devices for camera mode operation, set the Serializer M/S pin to LOW and the Deserializer M/S pin to HIGH. Before initiating any I2C commands, the Deserializer needs to be programmed with the target slave device addresses and Serializer device address. SER_DEV_ID Regis- DISPLAY MODE OPERATION In Display mode, I2C transactions originate from the controller attached to the Serializer. The I2C slave core in the Serializer will detect if a transaction targets (local) registers within the Serialier or the (remote) registers within the Deserializer or a remote slave connected to the I2C master interface of the Deserializer. Commands are sent over the forward channel link to initiate the transactions. The Deserializer will receive the command and generate an I2C transaction on its local I2C 29 www.national.com DS92LX1621 / DS92LX1622 • • bus. At the same time, the Deserializer will capture the response on the I2C bus and return the response as a command on the bi-directional control channel. The Serializer parses the response and passes the appropriate response to the Serializer I2C bus. The physical device ID of the I2C slave in the Serializer is determined by the analog voltage on the ID[x] input. It can be reprogrammed by using the DEVICE_ID register and setting the bit . The device ID of the logical I2C slave in the Deserializer is determined by programming the DES ID in the Serializer. The state of the CAD] input on the Deserializer is used to set the device ID. The I2C transactions between Ser/Des will be bridged between the host controller to the remote slave. To configure the devices for display mode operation, set the Serializer M/S pin to HIGH and the Deserializer M/S pin to LOW. Before initiating any I2C commands, the Serializer needs to be programmed with the target slave device address and Serializer device address. DES_DEV_ID Register 0x06h sets the Deserializer device address and SLAVE_DEV_ID register 0x7h sets the remote target slave address. If the I2C slave address matches any of registers values, the I2C slave will hold the transaction allowing read or write to target device. Note: In Display mode operation, registers 0x08h~0x17h on Deserializer must be reset to 0x00. PROGRAMMABLE CONTROLLER An integrated I2C slave controller is embedded in each of the DS92LX1621 Serializer and DS92LX1622 Deserializer. It must be used to access and program the extra features embedded within the configuration registers. Refer to Table 1 and Table 2 for details of control registers. MULTIPLE DEVICE ADDRESSING Some applications require multiple camera devices with the same fixed address to be accessed on the same I2C bus. The DS92LX1621 / DS92LX1622 provide slave ID matching/aliasing to generate different target slave addresses when connecting more than two identical devices together on the same bus. This allows the slave devices to be independently addressed. Each device connected to the bus is addressable through a unique ID by programming of the SLAVE_ID_MATCH register on Deserializer. This will remap the SLAVE_ID_MATCH address to the target SLAVE_ID_INDEX address; up to 8 ID indexes are supported. The host controller must keep track of the list of I2C peripherals in order to properly address the target device. In a camera application, the microcontroller is located on the Deserializer side. In this case, the microcontroller programs the slave address matching registers and handles all data transfers to and from all slave I2C devices. This is useful in the event where camera modules are removed or replaced. For example in the configuration shown in Figure 26: • Host device (FPGA, frame grabber, etc.) is the I2C master and has an I2C master interface • The I2C protocol is bridged from DES A to SER A and from DES B to SER B • The I2C interfaces in SER A and SER B are both master interfaces If the master controller transmits I2C slave 0xA0, the DES A address 0xE0 will forward the transaction to remote Camera A. If the controller transmits slave address 0xA2, the DES B 0xE2 will recognize that 0xA2 is mapped to 0xA0 and will be transmitted to the remote Camera B. If controller sends command to address 0xB2, the DES B 0xE2 will forward transaction to slave device 0xB0. The Slave ID index/match is supported only in the camera mode (SER: M/S pin = L; DES: M/S pin = H). For Multiple device addressing in display mode (SER: M/S pin = H; DES: M/S pin = L), use the I2C pass through function. CRC (CYCLIC REDUNDANCY CHECK) A 4-bit CRC per symbol is reserved for checking the link integrity during transmission. The reporting status pin (PASS) is provided on the Deserializer side, which flags any mismatch of data transmitted to and from the remote device. The Deserializer's PLL must first be locked (LOCK pin is HIGH) to ensure the PASS status is valid. This error detection handling generates an interrupt signal onto the PASS output pin; notifying the host controller as soon as any errors are identified. When an error occurs, the PASS will asserts LOW. An adjustable interrupt threshold register is also available for managing the data flow. ERROR DETECTION The DS92LX1621 / DS92LX1622 chipset provides several error detection operations for ensuring data integrity in long distance transmission and reception. The data error detection function offers user flexibility and usability of performing bitby-bit and data transmission error checking. The error detection operating modes support data validation of the following signals: • Bi-directional Control Channel control data detection across serial link www.national.com Control VSYNC and HSYNC signals across serial link Parallel video/pixel data across serial link 30 DS92LX1621 / DS92LX1622 30123033 FIGURE 26. Multiple Device Addressing 31 www.national.com DS92LX1621 / DS92LX1622 communication to only specific devices on the remote bus. The feature is effective for both Camera mode and Display mode. For example in the configuration shown in Figure 27: If master controller transmits I2C transaction for address 0xA0, the SER A with I2C pass through enabled will transfer I2C commands to remote Camera A. The SER B with I2C pass through disabled, any I2C commands will be bypassed on the I2C bus to Camera B. I2C PASS THROUGH I2C pass-through provides an alternative means to independently address slave devices. The mode enables or disables I2C bidirectional control channel communication to the remote I2C bus. This option is used to determine whether or not an I2C instruction is to be transferred over to the remote I2C device. When enabled, the I2C bus traffic will continue to pass through and will be received by I2C devices downstream. If disabled, I2C commands will be blocked to the remote I2C device. The pass through function also provides access and 30123004 FIGURE 27. I2C Pass Through directional control channel, there will be a time variation of the GPIO signals arriving at the different target devices (between the parallel links). The maximum latency delta (t1) of the GPIO data transmitted across multiple links is 25 μs. Note: The user must verify that the timing variations between the different links are within their system and timing specifications. For example in the configuration shown in Figure 28: The maximum time (t1) between the rising edge of GPIO (i.e. sync signal) arriving at Camera A and Camera B is 25 μs. SYNCHRONIZING MULTIPLE CAMERAS For applications requiring multiple cameras for frame-synchronization, it is recommended to utilize the General Purpose Input/Output (GPIO) pins to transmit control signals to synchronize multiple cameras together. To synchronize the cameras properly, the system controller needs to provide a field sync output (such as a vertical or frame sync signal) and the cameras must be set to accept an auxiliary sync input. The vertical synchronize signal corresponds to the start and end of a frame and the start and end of a field. Note this form of synchronization timing relationship has a non-deterministic latency. After the control data is reconstructed from the bi- www.national.com 32 DS92LX1621 / DS92LX1622 30123053 FIGURE 28. Synchronizing Multiple Cameras 30123054 FIGURE 29. GPIO Delta Latency GENERAL PURPOSE I/O (GPIO) The DS92LX1621 / DS92LX1622 has up to 6 GPIO (2 dedicated and 4 programmable). GPIO[0] and GPIO[1] are always available and GPIO[2:5] are available depending on the parallel data bus size. DIN/ROUT[0:3] can be programmed into GPIOs (GPIO[2:5]) when the parallel data bus is less than 12 bits wide (10-bit data + HS,VS). Each GPIO can be configured as either an input or output port. The GPIO maximum switching rate is up to 66 kHz when configured for communication between Deserializer GPI to Serializer GPO. Whereas data flow configured for communication between Serializer GPI to Deserializer GPO is limited by the maximum data rate of the PCLK. AT-SPEED BIST (BISTEN, PASS) An optional AT SPEED Built in Self Test (BIST) feature supports at speed testing of the high-speed serial and the bidirectional control channel link. Control pins at the Deserializer are used to enable the BIST test mode and allow the system to initiate the test and set the duration. A HIGH on PASS pin indicates that all payloads received during the test were error free during the BIST duration test. A LOW on this pin at the conclusion of the test indicates that one or more payloads were detected with errors. The BIST duration is defined by the width of BISTEN. BIST starts when Deserializer LOCK goes HIGH and BISTEN is set HIGH. BIST ends when BISTEN goes LOW. Any errors detected after the BIST Duration are not included in PASS logic. 33 www.national.com DS92LX1621 / DS92LX1622 Note: AT-SPEED BIST is only available in the Camera mode and not the Display mode. The following diagram shows how to perform system AT SPEED BIST: 30123045 FIGURE 30. AT-SPEED BIST System Flow Diagram Step 1: Place the Deserializer in BIST Mode. Serializer and Deserializer power supply must be supplied. Enable the AT SPEED BIST mode on the Deserializer by set- ting the BISTEN pin High. The DS92LX1622 GPIO[1:0] pins are used to select the PCLK frequency of the on-chip oscillator for the BIST test on high speed data path. TABLE 3. BIST Oscillator Frequency Select DES GPIO [1:0] Oscillator Source min (MHz) External PCLK 10 01 Internal 10 Internal 25 11 Internal 12.5 max (MHz) 50 50 The Deserializer GPIO[1:0] set to 00 will bypass the on-chip oscillator and an external oscillator to Serializer PCLK input is required. This allows the user to operate BIST under different frequencies other than the predefined ranges. Step 2: Enable AT SPEED BIST by placing the Serializer into BIST mode. The deserializer will communicate through the back-channel to configure Serializer into BIST mode. Once the BIST mode is set, the Serializer will initiate BIST transmission to the Deserializer. Wait 10 ms for Deserializer to acquire lock and then monitor the LOCK pin transition from LOW to HIGH. At this point, AT SPEED BIST is operational and the BIST process has begun. www.national.com typ (MHz) 00 The Serializer will start transfer of an internally generated PRBS data pattern through the high speed serial link. This pattern traverses across the interconnecting link to the Deserializer. Check the status of the PASS pin; a HIGH indicates a pass, a LOW indicates a fail. A fail will stay LOW for ½ a clock cycle. If two or more bits fail in a row the PASS pin will toggle ½ clock cycle HIGH and ½ clock cycle low. The user can use the PASS pin to count the number of fails on the high speed link. In addition, there is a defined SER and DES register that will keep track of the accumulated error count. The Serializer DS92LX1621 GPIO[0] pin will be assigned as a PASS flag error indicator for the bi-directional control channel link. 34 DS92LX1621 / DS92LX1622 30123064 FIGURE 31. BIST Timing Diagram Step 3: Stop at SPEED BIST by turning off BIST mode in the Deserializer to determine Pass/Fail. To end BIST, the system must pull BISTEN pin of the Deserializer LOW. The BIST duration is fully defined by the BIS- TEN width and thus the Bit Error Rate is determined by how long the system holds BISTEN HIGH. 30123005 FIGURE 32. BIST BER Calculation For instance, if BISTEN is held HIGH for 1 second and the PCLK is running at 43 MHz with 16 bpp, then the Bit Error Rate is no better than 1.46E-9. Step 4: Place system in Normal Operating Mode by disabling BIST at the Serializer. Once Step 3 is complete, AT SPEED BIST is over and the Deserializer is out of BIST mode. To fully return to Normal mode, apply Normal input data into the Serializer. Any PASS result will remain unless it is changed by a new BIST session or cleared by asserting and releasing PDB. The default state of PASS after a PDB toggle is HIGH. It is important to note that AT SPEED BIST will only determine if there is an issue on the link that is not related to the clock and data recovery of the link (whose status is flagged with LOCK pin). LVCMOS VDDIO OPTION 1.8V or 3.3V SER Inputs and DES Outputs are user configurable to provide compatibility with 1.8V and 3.3V system interfaces. REMOTE WAKE UP (Camera Mode) After initial power up, the SER is in a low-power Standby mode. The DES (controlled by host controller) 'Remote Wakeup' register allows the DES side to generate a signal across the link to remotely wake-up the SER. Once the SER detects the wake-up signal, the SER switches from Standby mode to active mode. In active mode, the SER locks onto PCLK input (if present), otherwise the on-chip oscillator is used as the input clock source. Note the host controller should monitor the DES LOCK pin and confirm LOCK = H before performing any I2C communication across the link. For Remote Wake-up to function properly: • The chipset needs to be configured in Camera mode: SER M/S = 0 and DES M/S = 1 35 www.national.com DS92LX1621 / DS92LX1622 • • be connected to the PDB pin to ensure PDB arrives after all the VDD have stabilized. The SER expects remote wake-up by default at power on. Configure the control channel driver of the DES to be in remote wake up mode by setting DES register 0x26 to 0xC0. • Perform remote wake up on SER by setting DES register 0x01 b[2] to 1. • Return the control channel driver of the DES to the normal operation mode by setting DES register 0x26 to 0. The SER can also be put into standby mode by programming the DES remote wake up control register 0x01 b[2] REM_WAKEUP to 0. SIGNAL QUALITY ENHANCERS Des - Receiver Input Equalization (EQ) The receiver inputs provided input equalization filter in order to compensate for loss from the media. The level of equalization is controlled via register setting. EMI REDUCTION Des - Receiver Staggered Output The Receiver staggered outputs allows for outputs to switch in a random distribution of transitions within a defined window. Outputs transitions are distributed randomly. This minimizes the number of outputs switching simultaneously and helps to reduce supply noise. In addition it spreads the noise spectrum out reducing overall EMI. POWERDOWN The SER has a PDB input pin to ENABLE or Powerdown the device. The modes can be controlled by the host and is used to disable the link to save power when the remote device is not operational. An auto mode is also available. In this mode, the PDB pin is tied HIGH and the SER switches over to an internal oscillator when the PCLK stops or not present. When a PCLK starts again, the SER will then lock to the valid input PCLK and transmits the data to the DES. In powerdown mode, the high-speed driver outputs are static (HIGH). The DES has a PDB input pin to ENABLE or Powerdown the device. This pin can be controlled by the system and is used to disable the DES to save power. An auto mode is also available. In this mode, the PDB pin is tied HIGH and the DES will enter powerdown when the serial stream stops. When the serial stream starts up again, the DES will lock to the input stream and assert the LOCK pin and output valid data. In powerdown mode, the Data and PCLK outputs are set by the OSS_SEL control register. Des Spread Spectrum Clocking Compatibilty The DS92LX1622 parallel data and clock outputs have programmable SSCG ranges from 9 kHz–66 kHz and ±0.5%– ±2% from 20 MHz to 50 MHz. The modulation rate and modulation frequency variation of output spread is controlled through the SSC control registers. PIXEL CLOCK EDGE SELECT (TRFB/RRFB) The TRFB/RRFB selects which edge of the Pixel Clock is used. For the SER, this register determines the edge that the data is latched on. If TRFB register is 1, data is latched on the Rising edge of the PCLK. If TRFB register is 0, data is latched on the Falling edge of the PCLK. For the DES, this register determines the edge that the data is strobed on. If RRFB register is 1, data is strobed on the Rising edge of the PCLK. If RRFB register is 0, data is strobed on the Falling edge of the PCLK. POWER UP REQUIREMENTS AND PDB PIN It is required to delay and release the PDB input signal after VDD (VDDn and VDDIO) power supplies have settled to the recommended operating voltages. A external RC network can 30123051 FIGURE 33. Programmable PCLK Strobe Select www.national.com 36 AC COUPLING The SER/DES supports only AC-coupled interconnects through an integrated DC balanced decoding scheme. To use 30123038 FIGURE 34. AC-Coupled Application For high-speed Channel Link III transmissions, the smallest available package should be used for the AC coupling capacitor. This will help minimize degradation of signal quality due to package parasitics. The most common used capacitor value for the interface is 0.1μF. TYPICAL APPLICATION CONNECTION Figure 35 shows a typical connection of the DS92LX1621 Serializer. 37 www.national.com DS92LX1621 / DS92LX1622 the device in an AC-coupled application, insert external AC coupling capacitors in series in the Channel Link III signal path as illustrated in Figure 34. Applications Information DS92LX1621 / DS92LX1622 30123055 FIGURE 35. DS92LX1621 Typical Connection Diagram www.national.com 38 DS92LX1621 / DS92LX1622 Figure 36 shows a typical connection of the DS92LX1622 Deserializer. 30123056 FIGURE 36. DS92LX1622 Typical Connection Diagram 39 www.national.com DS92LX1621 / DS92LX1622 bypass capacitors connected to the plane with via on both ends of the capacitor. Connecting power or ground pins to an external bypass capacitor will increase the inductance of the path. A small body size X7R chip capacitor, such as 0603, is recommended for external bypass. Its small body size reduces the parasitic inductance of the capacitor. The user must pay attention to the resonance frequency of these external bypass capacitors, usually in the range of 20-30 MHz. To provide effective bypassing, multiple capacitors are often used to achieve low impedance between the supply rails over the frequency of interest. At high frequency, it is also a common practice to use two vias from power and ground pins to the planes, reducing the impedance at high frequency. Some devices provide separate power for different portions of the circuit. This is done to isolate switching noise effects between different sections of the circuit. Separate planes on the PCB are typically not required. Pin Description tables typically provide guidance on which circuit blocks are connected to which power pin pairs. In some cases, an external filter many be used to provide clean power to sensitive circuits such as PLLs. Use at least a four layer board with a power and ground plane. Locate LVCMOS signals away from the differential lines to prevent coupling from the LVCMOS lines to the differential lines. Closely-coupled differential lines of 100 Ohms are typically recommended for differential interconnect. The closely coupled lines help to ensure that coupled noise will appear as common-mode and thus is rejected by the receivers. The tightly coupled lines will also radiate less. Information on the LLP style package is provided in National Application Note: AN-1187. TRANSMISSION MEDIA The Ser/Des chipset is intended to be used over a wide variety of balanced cables depending on distance and signal quality requirements. The Ser/Des employ internal termination providing a clean signaling environment. The interconnect for Channel Link III interface should present a differential impedance of 100 Ohms. Use of cables and connectors that have matched differential impedance will minimize impedance discontinuities. Shielded or un-shielded cables may be used depending upon the noise environment and application requirements. The chipset's optimum cable drive performance is achieved at 43 MHz at 10 meters length. The maximum signaling rate increases as the cable length decreases. Therefore, the chipset supports 50 MHz at shorter distances. Other cable parameters that may limit the cable's performance boundaries are: cable attenuation, near-end crosstalk and intra-pair skew. For obtaining optimal performance, the following is recommended: • Use Shielded Twisted Pair (STP) cable • 100Ω differential impedance and 24 AWG (or lower AWG) cable • Low intra-pair skew, impedance matched • Terminate unused conductors PCB LAYOUT AND POWER SYSTEM CONSIDERATIONS Circuit board layout and stack-up for the Ser/Des devices should be designed to provide low-noise power feed to the device. Good layout practice will also separate high frequency or high-level inputs and outputs to minimize unwanted stray noise pickup, feedback and interference. Power system performance may be greatly improved by using thin dielectrics (2 to 4 mils) for power / ground sandwiches. This arrangement provides plane capacitance for the PCB power system with low-inductance parasitics, which has proven especially effective at high frequencies, and makes the value and placement of external bypass capacitors less critical. External bypass capacitors should include both RF ceramic and tantalum electrolytic types. RF capacitors may use values in the range of 0.01 uF to 0.1 uF. Tantalum capacitors may be in the 2.2 uF to 10 uF range. Voltage rating of the tantalum capacitors should be at least 5X the power supply voltage being used. Surface mount capacitors are recommended due to their smaller parasitics. When using multiple capacitors per supply pin, locate the smaller value closer to the pin. A large bulk capacitor is recommend at the point of power entry. This is typically in the 50uF to 100uF range and will smooth low frequency switching noise. It is recommended to connect power and ground pins directly to the power and ground planes with www.national.com INTERCONNECT GUIDELINES See AN-1108 and AN-905 for full details. • Use 100Ω coupled differential pairs • Use the S/2S/3S rule in spacings — S = space between the pair — 2S = space between pairs — 3S = space to LVCMOS signal • Minimize the number of Vias • Use differential connectors when operating above 500Mbps line speed • Maintain balance of the traces • Minimize skew within the pair Additional general guidance can be found in the LVDS Owner’s Manual - available in PDF format from the National web site at: www.national.com/lvds 40 DS92LX1621 / DS92LX1622 Physical Dimensions inches (millimeters) unless otherwise noted DS92LX1621 Serializer NS Package Number SQA32A DS92LX1622 Deserializer NS Package Number SQA40A 41 www.national.com DS92LX1621 / DS92LX1622 10 - 50 MHz DC-Balanced Channel Link III Serializer and Deserializer with Bi-Directional Control Channel Notes For more National Semiconductor product information and proven design tools, visit the following Web sites at: www.national.com Products Design Support Amplifiers www.national.com/amplifiers WEBENCH® Tools www.national.com/webench Audio www.national.com/audio App Notes www.national.com/appnotes Clock and Timing www.national.com/timing Reference Designs www.national.com/refdesigns Data Converters www.national.com/adc Samples www.national.com/samples Interface www.national.com/interface Eval Boards www.national.com/evalboards LVDS www.national.com/lvds Packaging www.national.com/packaging Power Management www.national.com/power Green Compliance www.national.com/quality/green Switching Regulators www.national.com/switchers Distributors www.national.com/contacts LDOs www.national.com/ldo Quality and Reliability www.national.com/quality LED Lighting www.national.com/led Feedback/Support www.national.com/feedback Voltage References www.national.com/vref Design Made Easy www.national.com/easy www.national.com/powerwise Applications & Markets www.national.com/solutions Mil/Aero www.national.com/milaero PowerWise® Solutions Serial Digital Interface (SDI) www.national.com/sdi Temperature Sensors www.national.com/tempsensors SolarMagic™ www.national.com/solarmagic PLL/VCO www.national.com/wireless www.national.com/training PowerWise® Design University THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION (“NATIONAL”) PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS, IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT NATIONAL’S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS. EXCEPT AS PROVIDED IN NATIONAL’S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness. National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other brand or product names may be trademarks or registered trademarks of their respective holders. Copyright© 2011 National Semiconductor Corporation For the most current product information visit us at www.national.com National Semiconductor Americas Technical Support Center Email: [email protected] Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Technical Support Center Email: [email protected] National Semiconductor Asia Pacific Technical Support Center Email: [email protected] National Semiconductor Japan Technical Support Center Email: [email protected] IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP® Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2011, Texas Instruments Incorporated