CONNOR-WINFIELD 6213

3.3V LVCMOS Surface Mount
Crystal Clock Oscillator
6213, 6223, 6233
XO
2111 Comprehensive Drive
2111 Comprehensive Drive
Aurora, Illinois 60505
Aurora, Illinois 60505
Phone: 630- 851- 4722
Phone: 630- 851- 4722
Fax: 630- 851- 5040
Fax: 630- 851- 5040
www.conwin.com
www.conwin.com
US Headquarters:
630-851-4722
European Headquarters:
+353-61-472221
Features:
1.8 to 50 MHz
3.3V Operation
RoHS Compliant
Tri-State Enable / Disable Function
Overall Frequency Tolerance:
6213 ± 25 ppm
6223 ± 50 ppm
6233 ± 100 ppm
Temperature Range: -40 to 85°C
Power Saving Stand-By Current
Ceramic Surface Mount Package
Tape and Reel Packaging
The Connor-Winfield models 6213, 6223, and
6233 are a 6 x 3.5mm, 3.3V LVCMOS, Surface
Mount, Ceramic, Fixed Frequency Crystal
Oscillators (XO) designed for use in all
applictions requiring precision clocks. These
oscillators feature low stand-by current (10uA)
when the output is disabled. The RoHS
compliant, surface mount package is designed
for high-density mounting and is optimum for
mass production.
Absolute Maximum Ratings
Parameter
Storage Temperature
Supply Voltage (Vcc)
Minimum
-55
-0.5
Nominal
-
Maximum
125
7.0
Parameter
Frequency Range (Fo)
Frequency Tolerance
6213
6223
6233
Operating Temp Range
Supply Voltage (Vdd)
Supply Current (Icc)
1.80 to 31.999 MHz
32.0 to 50.0 MHz
Minimum
1.8
Nominal
-
Maximum
50
-25
-50
-100
-40
3.0
3.3
25
50
100
85
3.6
-
-
12
17
Units
°C
Vdc
Notes
Units
MHz
ppm
Notes
Operating Specifications
1
°C
Vdc
mA
Input Characteristics
Parameter
Enable Voltage - (Vih)
Disable Voltage - (Vil)
Enable Time
Disable Time
Output Disable Current (lcc)
Minimum
≥ 70% Vdd
-
Nominal
-
Maximum
≤ 30% Vdd
10
150
10
Units
Vdc
Vdc
mS
nS
uA
Notes
2
Units
pF
Notes
LVCMOS Output Characteristics
Bulletin
Page
Revision
Date
Sm082
1 of 2
01
30 May 2002
Parameter
Load
(Voh)
Voltage High
Low (Vol)
(loh)
Current High
Low (lol)
Duty Cycle at 50% of Vcc
Rise / Fall Time 10% to 90%
Start-Up Time
Jitter
Minimum
2.70
-2
45
-
Nominal
50
-
Maximum
15
0.36
2
55
5
10
5
Vdc
mA
%
nS
mS
pS RMS
Notes:
1. Inclusive of calibration @ 25°C , frequency vs temperature stability, supply voltage change, load change, shock and vibration, 10 years aging.
2. Oscillator output is enabled with no connection on pad 1
Specifications subject to change without notice. All dimensions in inches. © Copyright 1998 The Connor-Winfield Corporation
2111 Comprehensive Drive
Aurora, Illinois 60505
Phone: 630- 851- 4722
Fax: 630- 851- 5040
www.conwin.com
Package Characteristics
Package
Suggested Pad Layout
Hermetically sealed ceramic package and metal cover
Environmental Characteristics
Temperature Cycle
The specimen shall meet electrical characteristics after
tested 5 cycles of -55°C / 30 minutes and +125°C / 30 minutes
Hermetical
No bubbles appear in Flourinert (FC-43) at 125°C ±5°C for 5 minutes
Solvent Resistance
Marking will withstand immersion in
Isopropyl Alcohol or Trichloroethylene
Soldering
Bypass capacitor, C-by, should
be ceramic capacitor ≥ .01uf.
General Conditions
260°C max x 10 sec max x 2 times max or
230°C max x 180 sec max x 1 time
Typical Operation Data
(Vapor phase reflow)
20 to 100 sec up to 215°C, 50 sec
at 215°C, then down to room temperature per 1 to 5°C / sec
Test Circuit
OSCILLOSCOPE
Mechanical Characteristics
Free Drop
The specimen shall meet electrical characteristics after tested 3 times,
Free Drop testing on the hard wooden board from a height of 75 cm.
Vibration
The specimen shall meet electrical characteristics after tested
by the following conditions: 10-55Hz 1.5mm Amplitude,
55-2000 Hz 20 G's, 2 hours for each plane
Thermal Shock
After applied Thermal Shock of 260°C
max x 10 sec max x 2 times, or 230°C max x 180 sec max,
the specimen shall meet electrical characteristics
Solderability
(EIAJ-RCX-0102.101 Condition 1a)
1) Flux: MIL-F-14256 (WW Rosin=25%, Isopropyl Alcohol = 75%)
2) Solder: QQ-S-571 (Sn = 63%, Pb = 37%)
3) Solder bath temperature: 235°C ±5°C
4) Depth of immersion: Up to electrical terminal
5) Immersing time: Within 2 sec ±0.5 sec into solder bath
PROBE
POWER
SUPPLY
OSC
FREQ
COUNTER
INPUT FOR E/D
Output Waveform
OUTPUT WAVEFORM
TF
TR
90%
After performing the above procedures, a newly soldered coverage shall be greater than 90%
50%
Pad
1:
2:
3:
4:
Connection
Tri-State E/D
Ground
Output
VDD
10%
GND. LEVEL
T1
T0 = 1/ fo
SYMMETRY=(T1/T0)X100%
Dimensional Tolerance: ±.008 (.20mm)
Ordering Information
Tape and Reel Dimensions
6213
- 32.768 MHz
CLOCK
SERIES
CENTER
FREQUENCY
Bulletin
Page
Meets EIA-481A and EIAJ-1009B
3,000 PCS/Reel
Dimensional Tolerance: ±.02" (.508mm)
±.005"(.127mm)
Specifications subject to change without notice. All dimensions in inches. © Copyright 1998 The Connor-Winfield Corporation
Revision
Date
Sm082
2 of 2
01
30 May 2002