6113 - Connor

3.3V HCMOS Surface Mount
Crystal Clock Oscillator
6113, 6123, 6133
XO Features:
2111 Comprehensive Drive
Aurora, Illinois 60505
• 3.3V Operation
• Tri-State Enable / Disable Function
• RoHS Compliant
• Overall Frequency Tolerance:
6113 ± 25 ppm
6123 ± 50 ppm
6133 ± 100 ppm
• Temperature Range: 0 to 70°C
• Power Saving Stand-By Current
• Ceramic Surface Mount Package
• Tape and Reel Packaging
The Connor-Winfield models 6113, 6123, and
6133 are a 6 x 3.5mm, 3.3V HCMOS, Surface
Mount, Ceramic, Fixed Frequency Crystal
Oscillators (XO) designed for use in all applictions
requiring precision clocks. These oscillators
feature low stand-by current (10uA) when the
output is disabled. The RoHS compliant, surface
mount package is designed for high-density
mounting and is optimum for mass production.
Phone: 630- 851- 4722
Fax: 630- 851- 5040
www.conwin.com
US Headquarters:
630-851-4722
European Headquarters:
+353-61-472221
Absolute Maximum Ratings
Parameter
Minimum
Parameter
Minimum
Storage Temperature
Supply Voltage (Vcc)
-55
-0.5
Nominal
-
-
Maximum
125
7.0
Units
Notes
Units
Notes
°C
Vdc
Operating Specifications
Nominal
Maximum
Frequency Range (Fo)
1.8
-
50
Frequency Tolerance
6113
-25
-
25
6123
-50
-
50
6133
-100
-
100
Operating Temp Range
0
-
70
Supply Voltage (Vdd)
3.0
3.3
3.6
Supply Current (Icc)
1.80 to 31.999 MHz
-
-
12
32.0 to 50.0 MHz
-
-
17
MHz
ppm
1
°C
Vdc
mA
Input Characteristics
Parameter
Enable Voltage - (Vih)
Disable Voltage - (Vil)
Enable Time
Disable Time
Output Disable Current (lcc)
Minimum
≥ 70% Vdd
-
-
-
-
Nominal
-
-
-
-
-
Maximum
-
≤ 30% Vdd
10
150
10
Units
Notes
Units
Notes
Vdc
Vdc
mS
nS
uA
2
HCMOS Output Characteristics
Parameter
Load
Voltage High (Voh)
Low (Vol)
Current High (loh)
Low (lol)
Duty Cycle at 50% of Vcc
Rise / Fall Time 10% to 90%
Start-Up Time
Jitter
Bulletin
Page
Revision
Date
Sm081
1 of 2
02
06 May 2014
Minimum
-
2.70
-
-2
-
40
-
-
-
Nominal
-
-
-
-
-
50
-
-
-
Maximum
15
-
0.36
-
2
60
6
10
5
pF
Vdc
mA
%
nS
mS
pS RMS
Notes:
1. Inclusive of calibration @ 25°C , frequency vs temperature stability, supply voltage change, load change, shock and vibration, 10 years aging.
2. Oscillator output is enabled with no connection on pad 1
2111 Comprehensive Drive
Aurora, Illinois 60505
Phone: 630- 851- 4722
Fax: 630- 851- 5040
www.conwin.com
Package Characteristics
Package
Suggested Pad Layout
Hermetically sealed ceramic package and metal cover
Environmental Characteristics
Temperature Cycle
The specimen shall meet electrical characteristics after
tested 5 cycles of -55°C / 30 minutes and +125°C / 30 minutes
Hermetical
No bubbles appear in Flourinert (FC-43) at 125°C ±5°C for 5 minutes
Solvent Resistance
Marking will withstand immersion in
Isopropyl Alcohol or Trichloroethylene
Soldering
Bypass capacitor, C-by, should
be ceramic capacitor ≥ .01uf.
General Conditions
260°C max x 10 sec max x 2 times max or
230°C max x 180 sec max x 1 time
Typical Operation Data
(Vapor phase reflow)
20 to 100 sec up to 215°C, 50 sec
at 215°C, then down to room temperature per 1 to 5°C / sec
Test Circuit
OSCILLOSCOPE
Mechanical Characteristics
Free Drop
The specimen shall meet electrical characteristics after tested 3 times,
Free Drop testing on the hard wooden board from a height of 75 cm.
Vibration
The specimen shall meet electrical characteristics after tested
by the following conditions: 10-55Hz 1.5mm Amplitude,
55-2000 Hz 20 G's, 2 hours for each plane
Thermal Shock
After applied Thermal Shock of 260°C
max x 10 sec max x 2 times, or 230°C max x 180 sec max,
the specimen shall meet electrical characteristics
Solderability
(EIAJ-RCX-0102.101 Condition 1a)
1) Flux: MIL-F-14256 (WW Rosin=25%, Isopropyl Alcohol = 75%)
2) Solder: QQ-S-571 (Sn = 63%, Pb = 37%)
3) Solder bath temperature: 235°C ±5°C
4) Depth of immersion: Up to electrical terminal
5) Immersing time: Within 2 sec ±0.5 sec into solder bath
After performing the above procedures, a newly soldered coverage shall be greater than 90%
PROBE
POWER
SUPPLY
OSC
FREQ
COUNTER
INPUT FOR E/D
Output Waveform
OUTPUT WAVEFORM
TF
TR
90%
50%
Pad Connection
1: Tri-State E/D
2: Ground
3: Output
4: VDD
Dimensional Tolerance: ±.008 (.20mm)
10%
GND. LEVEL
T1
T0 = 1/ fo
SYMMETRY=(T1/T0)X100%
Ordering Information
Tape and Reel Dimensions
6113-050.0M
CLOCK
SERIES
Dimensional Tolerance: ±.02" (.508mm)
±.005"
(.127mm)
CENTER
FREQUENCY
Bulletin
Page
Revision
Meets EIA-481A and EIAJ-1009B
3,000 PCS/Reel
Specifications subject to change without notification. See Connor-Winfield's website for latest revision. All dimensions in inches.
© Copyright 2014 The Connor-Winfield Corporation Not intended for life support applications.
Date
Sm081
2 of 2
02
06 May 2014