5.0V Surface Mount Crystal Clock Oscillator HSM9 Features: XO 2111 Comprehensive Drive 2111 Comprehensive Drive Aurora, Illinois 60505 Aurora, Illinois 60505 Phone: 630- 851- 4722 Phone: 630- 851- 4722 Fax: 630- 851- 5040 Fax: 630- 851- 5040 www.conwin.com www.conwin.com US Headquarters: 630-851-4722 European Headquarters: +353-61-472221 The Connor-Winfield HSM91, HSM92, HSM93, and HSM94 models are 7.5mm x 5mm, 5.0V HCMOS, Surface Mount, Fixed Frequency Crystal Oscillators (XO) designed for use in all applications requiring precision clocks. The RoHS compliant surface mount package is designed for high-density mounting and is optimum for mass production. 1.0 to 80 MHz 5.0V Operation RoHS Compliant Tri-State Enable / Disable Overall Frequency Tolerance: HSM94 ± 20 ppm, HSM91 ± 25 ppm HSM92 ± 50 ppm, HSM93 ± 100 ppm Temperature Range: 0 to 70°C Ceramic Surface Mount Package Tape and Reel Packaging Absolute Maximum Ratings Parameter Storage Temperature Supply Voltage (Vcc) Minimum -55 -0.5 Parameter Frequency Range (Fo) HSM94 HSM91 HSM92 HSM93 Frequency Tolerance HSM94 HSM91 HSM92 HSM93 Operating Temp Range Supply Voltage (Vdd) Supply Current (Icc) 1.0 to 31.999 MHz 32 to 49.999 MHz 50 to 80.0 MHz Minimum Nominal - Maximum 125 7.0 Units °C Vdc Notes Units MHz Notes ppm 1 Operating Specifications 1.8 1.0 1.0 1.0 -20 -25 -50 -100 0 4.5 - Nominal - - 5.0 - Maximum 80 20 25 50 100 70 5.5 27 45 75 °C Vdc mA Input Characteristics Parameter Enable Voltage - (Vih) Disable Voltage - (Vil) Enable Time Disable Time Minimum ≥ 70% Vdd - Nominal - Maximum ≤ 30% Vdd 100 100 Units Vdc Vdc mS nS Notes 2 Units pF Notes HCMOS Output Characteristics Bulletin Page Revision Date Sm006 1 of 2 27 07 May 2008 Parameter Load (Voh) Voltage High Low (Vol) (loh) Current High Low (lol) Duty Cycle at 50% of Vcc Rise / Fall Time 10% to 90% Start-Up Time Jitter Minimum 4.5 -16 45 - Nominal 50 - Maximum 50 0.55 16 55 6 10 5 Vdc mA % nS mS pS RMS Notes: 1. Inclusive of calibration @ 25°C , frequency vs temperature stability, supply voltage change, load change, shock and vibration, 10 years aging. 2. Oscillator output is enabled with no connection on pad 1 Specifications subject to change without notice. All dimensions in inches. © Copyright 1998 The Connor-Winfield Corporation 2111 Comprehensive Drive Aurora, Illinois 60505 Phone: 630- 851- 4722 Fax: 630- 851- 5040 www.conwin.com Package Characteristics Package Suggested Pad Layout Hermetically sealed ceramic package and metal cover Environmental Characteristics Temperature Cycle The specimen shall meet electrical characteristics after tested 5 cycles of -55°C / 30 minutes and +125°C / 30 minutes Hermetical No bubbles appear in Flourinert (FC-43) at 125°C ±5°C for 5 minutes Solvent Resistance Marking will withstand immersion in Isopropyl Alcohol or Trichloroethylene Soldering General Conditions 260°C max x 10 sec max x 2 times max or 230°C max x 180 sec max x 1 time Typical Operation Data (Vapor phase reflow) 20 to 100 sec up to 215°C, 50 sec at 215°C, then down to room temperature per 1 to 5°C / sec Mechanical Characteristics Bypass capacitor, C-by, should be ceramic capacitor ≥ .01 uf Test Circuit OSCILLOSCOPE Vcc PROBE POWER SUPPLY Free Drop The specimen shall meet electrical characteristics after tested 3 times, Free Drop testing on the hard wooden board from a height of 75 cm. Vibration The specimen shall meet electrical characteristics after tested by the following conditions: 10-55Hz 1.5mm Amplitude, 55-2000 Hz 20 G's, 2 hours for each plane Thermal Shock After applied Thermal Shock of 260°C max x 10 sec max x 2 times, or 230°C max x 180 sec max, the specimen shall meet electrical characteristics Solderability (EIAJ-RCX-0102.101 Condition 1a) 1) Flux: MIL-F-14256 (WW Rosin=25%, Isopropyl Alcohol = 75%) 2) Solder: QQ-S-571 (Sn = 63%, Pb = 37%) 3) Solder bath temperature: 235°C ±5°C 4) Depth of immersion: Up to electrical terminal 5) Immersing time: Within 2 sec ±0.5 sec into solder bath .01uf OSC FREQ COUNTER INPUT FOR E/D Output Waveform After performing the above procedures, a newly soldered coverage shall be greater than 90% SYMMETRY Pin Connections 1: Tri-State E/D 2: Ground 3: Output 4: VDD Tape and Reel Dimensions Ordering Information HSM91 - 050.0M CLOCK SERIES CENTER FREQUENCY Dimensional Tolerance: ±.02" (.508mm) ±.005"(.127mm) Bulletin Page Meets EIA-481A and EIAJ-1009B 2,000 PCS/Reel Specifications subject to change without notice. All dimensions in inches. © Copyright 1998 The Connor-Winfield Corporation Revision Date Sm006 2 of 2 27 07 May 2008