CAPACITORS TANTALUM DIPPED SH SECTION 1 The ‘SH’ is a premium grade tantalum capacitor, exhibiting ultra-low leakagecurrent and impedance in small case sizes. Applications for this device include:High density logic boards - where space is a premium Instrumentation - requiring high temperature stability Timing circuits - requiring low leakage current Decoupling circuits - requiring low impedance Product is normally supplied loose on a 5mm pitch, but it is also available with a 2.5mm pitch and also taped & reeled for auto-insertion. All product is manufactured to comply with Dubilier’s stringent quality standards involving quality checks at each stage of processing and production. SPECIFICATION RANGE V6.3 10 162535 µF øxl/mm øxl/mm øxl/mm øxl/mm øxl/mm 0.1 4.5x7.0 0.15 4.5x7.0 0.22 4.5x7.0 0.33 4.5x7.0 0.47 4.5x7.0 0.68 4.5x7.0 1.0 4.5x7.0 4.5x7.0 1.5 4.5x7.0 4.5x7.0 4.5x7.0 2.2 4.5x7.0 4.5x7.0 4.5x7.0 4.5x7.5 3.3 4.5x7.0 4.5x7.0 4.5x7.0 4.5x7.5 5.0x8.5 4.7 4.5x7.0 4.5x7.0 4.5x7.5 5.0x8.5 5.5x8.5 6.8 4.5x7.0 4.5x7.5 5.0x8.5 5.0x9.0 6.0x8.5 10 4.5x7.5 5.0x8.5 5.0x9.0 5.5x9.0 6.0x10.0 15 5.0x8.5 5.0x9.0 5.5x8.5 6.0x10.0 7.0x10.5 22 5.0x9.0 5.5x8.5 6.0x10.0 7.0x10.5 8.0x12.5 33 5.5x8.5 6.0x9.0 6.0x10.0 8.0x12.0 9.0x14.0 47 6.0x10.0 6.5x10.0 8.0x12.0 9.0x14.0 9.0x15.0 68 6.5x10.0 7.0x10.5 9.0x12.0 9.0x16 100 7.0x10.5 8.0x12.5 9.0x16 150 8.0x12.5 9.0x14.5 9.0x16 220 9.0x14.0 10.0x17 10.0x18.5 330 10.0x17 10.0x18.5 50 øxl/mm 4.5x7.0 4.5x7.0 4.5x7.0 4.5x7.0 4.5x7.0 4.5x7.0 5.0x8.5 5.0x9.0 5.5x8.5 6.0x10.0 6.5x10.0 7.0x10.5 8.0x13 8.5x14 9.0x14 Temperature Life Time Tolerance Leakage Current -55 to +85˚C (125˚C operation possible with de-rating) 2000 Hours @ +85°C ± 20% (10% available) <0.008CV or 0.05µA whichever larger (>2 mins.) All parts supplied with 5mm pitch as standard. 2.5mm pitch also available on parts with 7mm diameter or less. ORDERING INFORMATION SH 10 16 TR Range Capacitance µF Voltage V Options: TR = Tape/Reel k = 10% Tol 2.5P : 2.5 pitch Blank = 5mm pitch 106 Fax: 01371 875075 www.dubilier.co.uk Tel: 01371 875758 CAPACITORS TANTALUM DIPPED SH Test Time/Hr Leakage Current/µA Capacitance/µF Tan ∂ Stability at Temperature Extremes Humidity 40˚C, 90-95% RH 21 days Shelf Life 2000 ± 48 Less than 125% of initial value Within ± 10% of initial value Less than or equal to initial value TAN ∂ Capacitance/µF Tan ∂ 0.1 to 1.5 0.04 2.2 to 6.8 0.06 10 to 68 100 to 220 0.08 0.1 IMPEDANCE (ohms MAX.) V6.3 10 162535 µF 0.1 26.0 0.15 21.0 0.22 17.0 0.33 15.0 0.47 13.0 0.68 10.0 1.0 10.0 8.0 1.5 10.0 8.0 6.0 2.2 13.0 8.0 6.0 5.0 3.3 13.0 10.0 6.0 5.0 4.0 4.7 10.0 8.0 5.0 4.0 3.0 6.8 8.0 6.0 4.0 3.1 2.5 10 6.0 5.0 3.2 2.5 2.0 15 5.0 3.7 2.5 2.0 1.6 22 3.7 2.7 2.0 1.5 1.3 33 3.0 2.1 1.6 1.2 1.0 47 2.0 1.7 1.3 1.0 0.8 68 1.8 1.3 1.0 0.8 100 1.6 1.0 0.8 150 0.9 0.8 0.6 220 0.9 0.6 0.5 330 0.7 0.5 -55˚C Capacitance within ± 12% max (better than -5% typ) +85˚C Capacitance within ± 12% max (better than +5% typ). Leakage current within 10% initial value. Capacitance within 10% of initial value. Leakage current within 125% of initial value.Tan ∂ less than or equal to initial value. Capacitance within 10% of initial value. 2000Hr @ 85˚C; no Leakage current within125% of initial voltage applied value. Tan ∂ less than or equal to initial value. Surge Voltage 1000 Capacitance within 5% of initial value. cycles @ 85˚C Leakage current less than or equal to initial value. Tan ∂ less than or equal to initial value. Rated Voltage/V 6.3 10 16 25 35 50 Surge Voltage/V 8 13 20 32 44 63 Temperature - Voltage 6.3 10 16 25 35 50 de-rating @ 125˚C 4 6.3 10 16 23 33 50 26.0 21.0 17.0 15.0 13.0 10.0 8.0 5.0 3.5 3.0 2.5 2.0 1.6 1.2 1.0 Impedance measured at 100KHz and 25˚C. SAFETY Operating Properties Material Content It is recommended that the following operating modes are not imposed on the capacitors; Tantalum capacitors contain no material normally considered as hazardous. Materials include: Epoxy Resin, Graphite, Manganese Dioxide, Tantalum, Tantalum Oxide. Noxious fumes may be emitted if incinerated. Over or reverse voltage Over temperature Power rating exceeded High current surge due to low impedance (we recommend that the circuit impedance should be 3Ω/V minimum). 107 Fax: 01371 875075 www.dubilier.co.uk Tel: 01371 875758 SECTION 1 ELECTRICAL ENDURANCE CAPACITORS TANTALUM DIPPED SH 4 DIMENSIONS (mm) Code Description Po Feed hole pitch P Hole centre to component centre S Lead pitch H Height to seating plane Do Feed hole diameter W Tape width Dimensions/mm 12.7 ± 0.3 6.35 ± 0.4 5.0 + 0.8/-0.2 (2.5 + 0.4/-0.1 option) 16.0 ± 0.5 4.0 ± 0.2 18.0 + 1.0/-0.5 CHARACTERISTICS Capacitance typically changes with temperature according to the curve DC leakage current (DCL) increases with increasing temperature according to the typical curve +20 Capacitance Value 10.0 Multiplier of DC Leakage Current Reference 1.0 at + 25 ˚C +10 0 -10 -20 1.0 -80 -60 -40 -20 0 +20 +40 +60 +80 +100 +120 Operating Temperature ˚C Optimum Solder Wave Profile Solder Wave Peak Temperature 260 °C Entrance to Solder Wave Flux Zone 0.1 -60 -40 -20 0 Exit from Solder Wave (Time in Wave – 2 to 4 Secs.) Preheat Zone Hot Air Debridging +20 +40 +60 +80 +100 +125 250 Operating Temperature –˚C Typical Effect of Temperature upon DC Leakage Current 225 80°C to 120 °C 200 Degrees – C° SECTION 1 OUTLINE DRAWING 175 150 Entrance to Solder Machine 125 Free Free Air Air Cool Cool Entrance to In-Line Cleaner Exit from In-Line Cleaner (time in cleaner may be less) Bottom Side Temperature Range 100 Immersion in Cleaning Vapor 150°C Max. 75 Top Side Nominal 50 25 Exit from Solder Machine 0 1 2 3 4 5 6 Time (Minutes) 108 Fax: 01371 875075 www.dubilier.co.uk Tel: 01371 875758